Some systems incorrectly report the ExtINTA pin of the I/O APIC as the
genuine target of the timer interrupt. Here is a change that copies timer
pin information found to the other pin if one has been found only. This
way both a direct and a through-8259A route is tested with the pin letting
these problematic systems work well enough. If no timer pin information
has been found for the I/O APIC, then local APIC variations are tried
only, similarly to what is done without the change (except without the
misleading messages).
Obviously if we try the first-chance path without being told by the BIOS
to do so, we should not complain either, so do not print the message in
this case.
The 64-bit variation should be updated with a call to
replace_pin_at_irq() which can be done with the upcoming merge. Since
add_pin_to_irq() is now always called in the first-chance path, the
condition to require it in the second-chance path no longer happens.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Keep the timer interrupt line masked when reconfiguring its interrupt
redirection entry in the I/O APIC.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unmask the timer interrupt line set up in the through-8259A mode
explicitly after setup_timer_IRQ0_pin() has set up the I/O APIC interrupt
redirection entry to let the two operations be unbound from each other.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename setup_ExtINT_IRQ0_pin() to setup_timer_IRQ0_pin() to better
reflect the upcoming role of a function setting up a (semi-)arbitrary I/O
APIC pin appropriately for the 8254 timer. By "appropriate" the following
settings are meant: edge-triggered, active-high, all the other settings
per-architecture. Adjust comments to reflect code appropriately. No
functional changes.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The LINT0 line of the local APIC is masked in the LVT0 entry in
check_timer() before this function is ever called. Removed the
redundant unmasking for better control.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For a better control the masking and unmasking of the timer interrupt
line in the 8259A operating in the 'Virtual Wire' mode has been moved out
of setup_ExtINT_IRQ0_pin() now, so remove the redundant calls from the
function.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no point in keeping the 8259A enabled if the I/O APIC NMI
watchdog has failed and the 8259A is not used to pass through regular
timer interrupts. This fixes problems with some systems where some logic
gets confused.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Disable the 8259A acting in the "virtual wire" mode to keep the interrupt
line inactive while fiddling with local APIC interrupt vector registers
associated with its destination inputs. To be on the safe side,
especially concerning flipping the trigger mode.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Disable the 8259A when routing of the timer interrupt through the chip to
the local APIC of the primary processor has failed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the "disable_8254_timer" and "enable_8254_timer" kernel
parameters. Now that AEOI acknowledgements are no longer needed for
correct timer operation, the 8259A can be kept disabled unconditionally
unless interrupts, either timer or watchdog ones, are actually passed
through it.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The code that used to be in do_slow_gettimeoffset() that relied on the
IRR bit of the master 8259A PIC for IRQ0 to check the state of the output
timer 0 of the PIT is no longer there. As a result, there is no need to
use the POLL command to acknowledge the timer interrupt in the "8259A
Virtual Wire", except for the NMI watchdog when the i82489DX APIC is used
(this is because this particular APIC treats NMIs as level-triggered and
keeping the input asserted would keep motherboard NMI sources held off for
too long). Remove the unneeded bits and adjust comments accordingly.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes section mismatch warnings in unlock_ExtINT_logic().
WARNING: arch/x86/kernel/built-in.o(.text+0x14a92): Section mismatch in reference from the function unlock_ExtINT_logic()
to the function .init.text:find_isa_irq_pin()
The function unlock_ExtINT_logic() references
the function __init find_isa_irq_pin().
This is often because unlock_ExtINT_logic lacks a __init
annotation or the annotation of find_isa_irq_pin is wrong.
Signed-off-by: Jacek Luczak <luczak.jacek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* Replace usages of CPU_MASK_NONE, CPU_MASK_ALL, NODE_MASK_NONE,
NODE_MASK_ALL to reduce stack requirements for large NR_CPUS
and MAXNODES counts.
* In some cases, the cpumask variable was initialized but then overwritten
with another value. This is the case for changes like this:
- cpumask_t oldmask = CPU_MASK_ALL;
+ cpumask_t oldmask;
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use cpumask_of_cpu() rather than the pair of cpus_clear() and cpu_set().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
No need to clear the memory allocated by alloc_bootmem().
It is already filled with zero.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove duplicate code by using ioapic_read_entry() and ioapic_write_entry()
in io_apic_{32,64}.c
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If one can find an ack pending pin, there is no need to check
the rest of them.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce a function to read the local APIC_ID.
This change is in preparation for additional changes to
the APICID functions that will come in a later patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@ change_compare_np @
expression E;
@@
(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)
@ include depends on change_compare_np @
@@
#include <linux/jiffies.h>
@ no_include depends on !include && change_compare_np @
@@
#include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Its previous use in a call to on_each_cpu() was pointless, as at the
time that code gets executed only one CPU is online. Further, the
function can be __cpuinit, and for this to work without
CONFIG_HOTPLUG_CPU setup_nmi() must also get an attribute (this one
can even be __init; on 64-bits check_timer() also was lacking that
attribute).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have a lot of code which differs only by the naming of specific
members of structures that contain registers. In order to enable
additional unifications, this patch drops the e- or r- size prefix
from the register names in struct pt_regs, and drops the x- prefixes
for segment registers on the 32-bit side.
This patch also performs the equivalent renames in some additional
places that might be candidates for unification in the future.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
4 socket quad core, 8 socket quad core will do apic ID lifting for BSP.
But io-apic regs for ExtINT still use 0 as dest.
so when we enable apic error vector in BSP, we will get one APIC error.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/4 -> Node 0
CPU: Physical Processor ID: 1
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
enabled ExtINT on CPU#0
ESR value after enabling vector: 00000000, after 0000000c
APIC error on CPU0: 0c(08)
ENABLING IO-APIC IRQs
Synchronizing Arb IDs.
So move enable_IO_APIC from setup_IO_APIC into setup_local_APIC and call it
before enabling the ACPI error vector.
[ tglx: arch/x86 adaptation ]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The commit 399287229c hacked the
ioapic resource mapping into apic.c for no good reason.
Move the code into io_apic_64.c where it belongs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is the tale of a full day spent debugging an ancient but elusive bug.
after booting up thousands of random .config kernels, i finally happened
to generate a .config that produced the following rare bootup failure
on 32-bit x86:
| ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
| ..MP-BIOS bug: 8254 timer not connected to IO-APIC
| ...trying to set up timer (IRQ0) through the 8259A ... failed.
| ...trying to set up timer as Virtual Wire IRQ... failed.
| ...trying to set up timer as ExtINT IRQ... failed :(.
| Kernel panic - not syncing: IO-APIC + timer doesn't work! Boot with apic=debug
| and send a report. Then try booting with the 'noapic' option
this bug has been reported many times during the years, but it was never
reproduced nor fixed.
the bug that i hit was extremely sensitive to .config details.
First i did a .config-bisection - suspecting some .config detail.
That led to CONFIG_X86_MCE: enabling X86_MCE magically made the bug disappear
and the system would boot up just fine.
Debugging my way through the MCE code ended up identifying two unlikely
candidates: the thing that made a real difference to the hang was that
X86_MCE did two printks:
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
Adding the same printks to a !CONFIG_X86_MCE kernel made the bug go away!
this left timing as the main suspect: i experimented with adding various
udelay()s to the arch/x86/kernel/io_apic_32.c:check_timer() function, and
the race window turned out to be narrower than 30 microseconds (!).
That made debugging especially funny, debugging without having printk
ability before the bug hits is ... interesting ;-)
eventually i started suspecting IRQ activities - those are pretty much the
only thing that happen this early during bootup and have the timescale of
a few dozen microseconds. Also, check_timer() changes the IRQ hardware
in various creative ways, so the main candidate became IRQ0 interaction.
i've added a counter to track timer irqs (on which core they arrived, at
what exact time, etc.) and found that no timer IRQ would arrive after the
bug condition hits - even if we re-enable IRQ0 and re-initialize the i8259A,
but that we'd get a small number of timer irqs right around the time when we
call the check_timer() function.
Eventually i got the following backtrace triggered from debug code in the
timer interrupt:
...trying to set up timer as Virtual Wire IRQ... failed.
...trying to set up timer as ExtINT IRQ...
Pid: 1, comm: swapper Not tainted (2.6.24-rc5 #57)
EIP: 0060:[<c044d57e>] EFLAGS: 00000246 CPU: 0
EIP is at _spin_unlock_irqrestore+0x5/0x1c
EAX: c0634178 EBX: 00000000 ECX: c4947d63 EDX: 00000246
ESI: 00000002 EDI: 00010031 EBP: c04e0f2e ESP: f7c41df4
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 8005003b CR2: ffe04000 CR3: 00630000 CR4: 000006d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
[<c05f5784>] setup_IO_APIC+0x9c3/0xc5c
the spin_unlock() was called from init_8259A(). Wait ... we have an IRQ0
entry while we are in the middle of setting up the local APIC, the i8259A
and the PIT??
That is certainly not how it's supposed to work! check_timer() was supposed
to be called with irqs turned off - but this eroded away sometime in the
past. This code would still work most of the time because this code runs
very quickly, but just the right timing conditions are present and IRQ0
hits in this small, ~30 usecs window, timer irqs stop and the system does
not boot up. Also, given how early this is during bootup, the hang is
very deterministic - but it would only occur on certain machines (and
certain configs).
The fix was quite simple: disable/restore interrupts properly in this
function. With that in place the test-system now boots up just fine.
(64-bit x86 io_apic_64.c had the same bug.)
Phew! One down, only 1500 other kernel bugs are left ;-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MSI interrupt handler registrations and fault handling support for Intel-IOMMU
hadrware.
This patch enables the MSI interrupts for the DMA remapping units and in the
interrupt handler read the fault cause and outputs the same on to the console.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normally we will have two segment not connected pin pin0, and pin after
15...
So we need to print out "not connected\n" for previous segment, before
printing out connected pins info...
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
