We were expecting to sit on this branch through most of the merge window since
the contents was merged into our tree late, but we ended up sitting on all of
our contents so it can go in with the rest.
The contents here is:
- A large branch of cleanups of the CM/PRM blocks on OMAP.
- A couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- A branch with DT updates for Freescale i.MX. including some shuffling from
.dts to .dtsi (include) files that causes a little churn.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ssbK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Olof Johansson:
"We were expecting to sit on this branch through most of the merge
window since the contents was merged into our tree late, but we ended
up sitting on all of our contents so it can go in with the rest.
The contents here is:
- a large branch of cleanups of the CM/PRM blocks on OMAP.
- a couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- a branch with DT updates for Freescale i.MX. including some
shuffling from .dts to .dtsi (include) files that causes a little
churn"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
ARM: OMAP4+: control: add support for initializing control module via DT
ARM: dts: dra7: add minimal l4 bus layout with control module support
ARM: dts: omap5: add minimal l4 bus layout with control module support
ARM: OMAP4+: control: remove support for legacy pad read/write
ARM: OMAP4: display: convert display to use syscon for dsi muxing
ARM: dts: omap4: add minimal l4 bus layout with control module support
ARM: dts: am4372: add minimal l4 bus layout with control module support
ARM: dts: am43xx-epos-evm: fix pinmux node layout
ARM: dts: am33xx: add minimal l4 bus layout with control module support
ARM: dts: omap3: add minimal l4 bus layout with control module support
ARM: dts: omap24xx: add minimal l4 bus layout with control module support
ARM: OMAP2+: control: add syscon support for register accesses
ARM: OMAP2+: id: cache omap_type value
ARM: OMAP2+: control: remove API for getting control module base address
ARM: OMAP2+: clock: add low-level support for regmap
ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
ARM: OMAP2+: CM: move SoC specific init calls within a generic API
ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
...
Pinmux node should be a reference to the base one, not a complete re-write
of it. Having the node like this also prevents modifying the node layout
in the base am4372.dtsi file, which is needed for control module changes.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP4/5 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the WUGEN HW block, kernels with this patch applied
won't have any suspend-resume facility when booted with old DTs,
and old kernels with updated DTs won't even boot.
On a platform with this patch applied, the system looks like
this:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 0 0 WUGEN 37 gp_timer
19: 233799 155916 GIC 27 arch_timer
23: 0 0 WUGEN 9 l3-dbg-irq
24: 1 0 WUGEN 10 l3-app-irq
27: 282 0 WUGEN 13 omap-dma-engine
44: 0 0 4ae10000.gpio 13 DMA
294: 0 0 WUGEN 20 gpmc
297: 506 0 WUGEN 56 48070000.i2c
298: 0 0 WUGEN 57 48072000.i2c
299: 0 0 WUGEN 61 48060000.i2c
300: 0 0 WUGEN 62 4807a000.i2c
301: 8 0 WUGEN 60 4807c000.i2c
308: 2439 0 WUGEN 74 OMAP UART2
312: 362 0 WUGEN 83 mmc2
313: 502 0 WUGEN 86 mmc0
314: 13 0 WUGEN 94 mmc1
350: 0 0 PRCM pinctrl, pinctrl
406: 35155709 0 GIC 109 ehci_hcd:usb1
407: 0 0 WUGEN 7 palmas
409: 0 0 WUGEN 119 twl6040
410: 0 0 twl6040 5 twl6040_irq_ready
411: 0 0 twl6040 0 twl6040_irq_th
IPI0: 0 1 CPU wakeup interrupts
IPI1: 0 0 Timer broadcast interrupts
IPI2: 95334 902334 Rescheduling interrupts
IPI3: 0 0 Function call interrupts
IPI4: 479 648 Single function call interrupts
IPI5: 0 0 CPU stop interrupts
IPI6: 0 0 IRQ work interrupts
IPI7: 0 0 completion interrupts
Err: 0
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add device tree nodes and pinmux entries for Video Processing
Front End (VPFE) on am43x epos evm.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
* AMLogic Meson8
* ARM Realview in DT mode
* Allwinner A80
* Broadcom BCM47081
* Broadcom Cygnus
* Freescale LS1021A
* Freescale Vybrid 500 series
* Mediatek MT6592, MT8127, MT8135
* STMicroelectronics STiH410
* Samsung Exynos4415
The level of support for the above differs widely, some are just
stubs with nothing more than CPU, memory and a UART, but others
are fairly complete. As usual, these get extended over time.
There are also many new boards getting added, this is the
list of model strings that are showing up in new dts files:
* ARM RealView PB1176
* Altera SOCFPGA Arria 10
* Asus RT-N18U (BCM47081)
* Buffalo WZR-1750DHP (BCM4708)
* Buffalo WZR-600DHP2 (BCM47081)
* Cygnus Enterprise Phone (BCM911360_ENTPHN)
* D-Link DIR-665
* Google Spring
* IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
* IGEPv2 Rev. F (TI OMAP AM/DM37x)
* LS1021A QDS Board
* LS1021A TWR Board
* LeMaker Banana Pi
* MarsBoard RK3066
* MediaTek MT8127 Moose Board
* MediaTek MT8135 evaluation board
* Mele M3
* Merrii A80 Optimus Board
* Netgear R6300 V2 (BCM4708)
* Nomadik STN8815NHK
* NovaTech OrionLXm
* Olimex A20-OLinuXino-LIME2
* Raspberry Pi Model B+
* STiH410 B2120
* Samsung Monk board
* Samsung Rinato board
* Synology DS213j
* Synology DS414
* TBS2910 Matrix ARM mini PC
* TI AM5728 BeagleBoard-X15
* Toradex Colibri VF50 on Colibri Evaluation Board
* Zynq ZYBO Development Board
Other notable changes include:
* exynos: cleanup of existing dts files
* mvebu: improved pinctrl support for Armada 370/XP
* nomadik: restructuring dts files
* omap: added CAN bus support
* shmobile: added clock support for some SoCs
* shmobile: added sound support for some SoCs
* sirf: reset controller support
* sunxi: continuing the relicensing under dual GPL/MIT
* sunxi: lots of new on-chip device support
* sunxi: working simplefb support (long awaited)
* various: provide stdout-path property for earlycon
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=BHwA
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Arnd Bergmann:
"The DT branch adds a lot of new stuff for additional SoC and board
support. The branch is the largest one and contains 513 out of the
total 972 non-merge arm-soc changesets for 3.19.
Most of the changes are about enabling additional on-chip devices for
existing machines, but there are also an unusual number of new SoC
types being added this time:
- AMLogic Meson8
- ARM Realview in DT mode
- Allwinner A80
- Broadcom BCM47081
- Broadcom Cygnus
- Freescale LS1021A
- Freescale Vybrid 500 series
- Mediatek MT6592, MT8127, MT8135
- STMicroelectronics STiH410
- Samsung Exynos4415
The level of support for the above differs widely, some are just stubs
with nothing more than CPU, memory and a UART, but others are fairly
complete. As usual, these get extended over time.
There are also many new boards getting added, this is the list of
model strings that are showing up in new dts files:
- ARM RealView PB1176
- Altera SOCFPGA Arria 10
- Asus RT-N18U (BCM47081)
- Buffalo WZR-1750DHP (BCM4708)
- Buffalo WZR-600DHP2 (BCM47081)
- Cygnus Enterprise Phone (BCM911360_ENTPHN)
- D-Link DIR-665
- Google Spring
- IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
- IGEPv2 Rev. F (TI OMAP AM/DM37x)
- LS1021A QDS Board
- LS1021A TWR Board
- LeMaker Banana Pi
- MarsBoard RK3066
- MediaTek MT8127 Moose Board
- MediaTek MT8135 evaluation board
- Mele M3
- Merrii A80 Optimus Board
- Netgear R6300 V2 (BCM4708)
- Nomadik STN8815NHK
- NovaTech OrionLXm
- Olimex A20-OLinuXino-LIME2
- Raspberry Pi Model B+
- STiH410 B2120
- Samsung Monk board
- Samsung Rinato board
- Synology DS213j
- Synology DS414
- TBS2910 Matrix ARM mini PC
- TI AM5728 BeagleBoard-X15
- Toradex Colibri VF50 on Colibri Evaluation Board
- Zynq ZYBO Development Board
Other notable changes include:
- exynos: cleanup of existing dts files
- mvebu: improved pinctrl support for Armada 370/XP
- nomadik: restructuring dts files
- omap: added CAN bus support
- shmobile: added clock support for some SoCs
- shmobile: added sound support for some SoCs
- sirf: reset controller support
- sunxi: continuing the relicensing under dual GPL/MIT
- sunxi: lots of new on-chip device support
- sunxi: working simplefb support (long awaited)
- various: provide stdout-path property for earlycon"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
ARM: BCM5301X: Add DT for Asus RT-N18U
ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
ARM: BCM5301X: Add DT for Netgear R6300 V2
ARM: BCM5301X: Add buttons for Netgear R6250
ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
arm: dts: zynq: Add Digilent ZYBO board
arm: dts: zynq: Move crystal freq. to board level
doc: dt: vendor-prefixes: Add Digilent Inc
Documentation: devicetree: Fix Xilinx VDMA specification
ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
ARM: dts: rockchip: add label property for leds on Radxa Rock
ARM: BCM5301X: Add LEDs for Netgear R6250 V1
ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
ARM: dts: add sysreg phandle to i2c device nodes for exynos
ARM: dts: Remove unused bootargs from exynos3250-rinato
ARM: dts: add board dts file for Exynos3250-based Monk board
...
This patch adds tscadc DT entries for am437x-gp-evm
and am43x-epos-evm.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DCDC3 supplies voltage to DDR. Fix DCDC3 volatge to 1.5V which is the reset
value. Programming to a non-reset value while executing from DDR will result
in random hangs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPMC binding is obviously very confusing as the values
are all over the place. People seem to confuse the GPMC partition
size for the chip select, and the device IO size within the GPMC
partition easily.
The ranges entry contains the GPMC partition size. And the
reg entry contains the size of the IO registers of the
device connected to the GPMC.
Let's fix the issue according to the following table:
Device GPMC partition size Device IO size
connected in the ranges entry in the reg entry
NAND 0x01000000 (16MB) 4
16550 0x01000000 (16MB) 8
smc91x 0x01000000 (16MB) 0xf
smc911x 0x01000000 (16MB) 0xff
OneNAND 0x01000000 (16MB) 0x20000 (128KB)
16MB NOR 0x01000000 (16MB) 0x01000000 (16MB)
32MB NOR 0x02000000 (32MB) 0x02000000 (32MB)
64MB NOR 0x04000000 (64MB) 0x04000000 (64MB)
128MB NOR 0x08000000 (128MB) 0x08000000 (128MB)
256MB NOR 0x10000000 (256MB) 0x10000000 (256MB)
Let's also add comments to the fixed entries while at it.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.
Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.
CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
Update the bindings for touchscreen size.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
window:
- Enable irqchip crossbar interrupt mapping. These changes
are based on an immutable irqchip branch set up by Jason
Cooper to make it easier to merge the related .dts changes.
- Removal of omap2 related static clock data that now comes
from device tree.
- Enabling of PHY regulators for various omaps
- Enabling of PCIe for dra7
- Add support for am437x starterkit
- Enable audio for for omap5
- Enable display and am335x-evmsk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4svh
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.17/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v3.17 merge window, part1" from Tony Lindgren:
First set of .dts changes for omaps for v3.17 merge window:
- Enable irqchip crossbar interrupt mapping. These changes
are based on an immutable irqchip branch set up by Jason
Cooper to make it easier to merge the related .dts changes.
- Removal of omap2 related static clock data that now comes
from device tree.
- Enabling of PHY regulators for various omaps
- Enabling of PCIe for dra7
- Add support for am437x starterkit
- Enable audio for for omap5
- Enable display and am335x-evmsk
* tag 'omap-for-v3.17/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (43 commits)
ARM: DTS: omap5-uevm: Enable basic audio (McPDM <-> twl6040)
ARM: DTS: omap5-uevm: Add node for twl6040 audio codec
ARM: DTS: omap5-uevm: Enable palmas clk32kgaudio clock
ARM: dts: dra7: Add dt data for PCIe controller
ARM: dts: dra7: Add dt data for PCIe PHY
ARM: dts: dra7: Add dt data for PCIe PHY control module
ARM: dts: dra7xx-clocks: Add missing clocks for second PCIe PHY instance
ARM: dts: dra7xx-clocks: rename pcie clocks to accommodate second PHY instance
ARM: dts: dra7xx-clocks: Add missing 32KHz clocks used for PHY
ARM: dts: dra7xx-clocks: Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
ARM: dts: dra7xx-clocks: Add divider table to optfclk_pciephy_div clock
ARM: dts: dra7-evm: Add regulator information to USB2 PHYs
ARM: omap2plus_defconfig: enable TPS65218 configs
ARM: dts: AM437x: Add TPS65218 device tree nodes
ARM: dts: AM437x: Fix i2c nodes indentation
ARM: dts: AM43x: Add TPS65218 device tree nodes
ARM: dts: Add devicetree for Gumstix Pepper board
ARM: dts: dra7: add crossbar device binding
ARM: dts: dra7: add routable-irqs property for gic node
ARM: OMAP24xx: clock: remove legacy clock data
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add TPS65218 device tree nodes. i2c clock frequency setting
also added as part of tps65218 nodes addition. As i2c clock
enabling is required.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x EPOS evm use external clock for RMII interface.
Enable the same in DT.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MTD NAND partition for file-system should start at offset=0xA00000
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux for hdq/1wire on
am43x epos evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixup Y resolution and add default pin state. Also update
the compatible id.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable
- USB PHY
- USB
for am43x-epos-evm
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add card detect gpio for SD card slot and include dt gpio header.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch:
- enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
- adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
present on following boards:
am43x-epos-evm:
On this board, NAND Flash control lines are muxed with QSPI, Thus only
one of the two can be used at a time. Selection is controlled by:
(a) dynamically driving following GPIO pin from software
GPMC_A0(GPIO) == 0 NAND is selected (default)
GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add AM43x ePOS EVM minimal DT source - this is a minimal one to get
it booting. Also include it in omap2plus dtbs and document bindings.
The hardware is under development.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
