The watchdog driver of the SoC uses the clk API to
get the clock associated with the watchdog device.
However the MT7620 specific setup code does not
register a clock for the watchdog device yet which
leads to the following error:
rt2880_wdt: probe of 10000120.watchdog failed with error -2
Register a clock device for the watchdog in order to
avoid the error and make the watchdog usable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5756/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code assumes that the peripheral clock always
runs at 40MHz which is not true in all configuration. The
peripheral clock can also use the reference clock instead
of the fixed 40MHz rate. If the reference clock runs at a
different rate, various peripheries are behaving incorrectly.
Additionally, the currectly calculated system clock is also
wrong. The actual value what the code computes is the rate
of the DRAM which can be different from the system clock.
Add new helper functions to get the rate of the different
clocks and use the correct values for the registered clock
devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5755/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Newer Ralink SoC (MT7620x and RT5350) have a 50KHz clock that runs independent
of the SoC master clock. If we want to automatic frequency scaling to work we
need to use the systick timer as the clock source.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5669/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 3747069b25e419f6b51395f48127e9812abc3596 upstream.
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
Here, we remove all the MIPS __cpuinit from C code and __CPUINIT
from asm files. MIPS is interesting in this respect, because there
are also uasm users hiding behind their own renamed versions of the
__cpuinit macros.
[1] https://lkml.org/lkml/2013/5/20/589
[ralf@linux-mips.org: Folded in Paul's followup fix.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5494/
Patchwork: https://patchwork.linux-mips.org/patch/5495/
Patchwork: https://patchwork.linux-mips.org/patch/5509/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
'compatible' is used by strlen() in __of_device_is_compatible().
Ensure strings are always '\0' terminated.
'of_ids is not a structure in "include/uapi/*", so no need to initialize
it completly; using strlcpy() instead of strncpy() will do.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: juhosg@openwrt.org
Cc: linux-mips@linux-mips.org
Cc: Linux-Arch <linux-arch@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/5330/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On RT5350 the memory size is set to Bytes and not MegaBytes due to a missing
multiplier.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/5378/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This sets up the devicetree file for the rt3050 chip series and rt3052
eval board to use the right compatible string for the dwc2 driver.
Acked-by: John Crispin <blogic@openwrt.org>
Cc: blogic@openwrt.org
Cc: linux-mips@linux-mips.org
Cc: Matthijs Kooijman <matthijs@stdin.nl>
Patchwork: https://patchwork.linux-mips.org/patch/5226/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
- More work on DT support for various platforms
- Various fixes that were to late to make it straight into 3.9
- Improved platform support, in particular the Netlogic XLR and
BCM63xx, and the SEAD3 and Malta eval boards.
- Support for several Ralink SOC families.
- Complete support for the microMIPS ASE which basically reencodes the
existing MIPS32/MIPS64 ISA to use non-constant size instructions.
- Some fallout from LTO work which remove old cruft and will generally
make the MIPS kernel easier to maintain and resistant to compiler
optimization, even in absence of LTO.
- KVM support. While MIPS has announced hardware virtualization
extensions this KVM extension uses trap and emulate mode for
virtualization of MIPS32. More KVM work to add support for VZ
hardware virtualizaiton extensions and MIPS64 will probably already
be merged for 3.11.
Most of this has been sitting in -next for a long time. All defconfigs
have been build or run time tested except three for which fixes are being
sent by other maintainers.
Semantic conflict with kvm updates done as per Ralf
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (118 commits)
MIPS: Add new GIC clockevent driver.
MIPS: Formatting clean-ups for clocksources.
MIPS: Refactor GIC clocksource code.
MIPS: Move 'gic_frequency' to common location.
MIPS: Move 'gic_present' to common location.
MIPS: MIPS16e: Add unaligned access support.
MIPS: MIPS16e: Support handling of delay slots.
MIPS: MIPS16e: Add instruction formats.
MIPS: microMIPS: Optimise 'strnlen' core library function.
MIPS: microMIPS: Optimise 'strlen' core library function.
MIPS: microMIPS: Optimise 'strncpy' core library function.
MIPS: microMIPS: Optimise 'memset' core library function.
MIPS: microMIPS: Add configuration option for microMIPS kernel.
MIPS: microMIPS: Disable LL/SC and fix linker bug.
MIPS: microMIPS: Add vdso support.
MIPS: microMIPS: Add unaligned access support.
MIPS: microMIPS: Support handling of delay slots.
MIPS: microMIPS: Add support for exception handling.
MIPS: microMIPS: Floating point support.
MIPS: microMIPS: Fix macro naming in micro-assembler.
...
Call detect_memory_region() from plat_mem_setup() unless the size was already
read from the system controller.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5184/
Populate struct soc_info with the data that describes our RAM window.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5183/
Populate struct soc_info with the data that describes our RAM window.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5182/
Populate struct soc_info with the data that describes our RAM window.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5181/
Populate struct soc_info with the data that describes our RAM window.
As memory detection fails on RT5350 we read the amount of available memory
from the system controller.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5180/
Depending on the actual SoC we have a different base address as well as minimum
and maximum size for RAM. Add these fields to the per SoC structure.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5179/
Add a dtsi file for MT7620A SoC and a sample dts file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5190/
Add a dtsi file for RT3883 SoC and a sample dts file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5189/
Add a dtsi file for RT2880 SoC and a sample dts file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5188/
* remove nodes for cores whose drivers are not upstream yet
* add compat string for an additional soc
* fix a whitespace error
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: http://patchwork.linux-mips.org/patch/5186/
Add support code for mt7620 SOC.
The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5177/
Add support code for rt3883 SOC.
The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5185/
Add support code for rt2880 SOC.
The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5176/
Add a field for the uart muxing mask and set it inside the rt305x setup code.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5744/
This will be used for RT3662/RT3883.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5173/
These structures are exported via struct ralink_pinmux rt_gpio_pinmux and can
hence be static.
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5172/
RT2880 has a different location for the early serial port.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5170/
Trivial patch that adds a comment that makes the code more readable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5168/
Add a few missing clocks.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5167/
The Ralink IRQ code was not handling the PCI IRQ yet. Add this functionaility
to make PCI work on rt3883.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5165/
Convert the ralink IRQ code to make use of the new MIPS IRQ controller OF
mappings.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4900/
Add the Kbuild symbols and Makefiles needed to actually build the ralink code
from this series
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4899/
This adds the devicetree file that describes the rt305x evaluation kit.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4898/
Add support code for rt3050, rt3052, rt3350, rt3352 and rt5350 SOC.
The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4896/
Add the code needed to make early printk work.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4897/
Until there is a generic MIPS way of handing the DTB over from bootloader to
kernel we rely on a built in devicetrees. The OF code also remaps those register
ranges that we use global in our drivers.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4895/
These SoCs have a limited number of fixed rate clocks. Add support for the
clk and clkdev api.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4894/
Resetting these SoCs requires no real magic. The code is straight forward.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4891/
All of the Ralink Wifi SoC currently supported by this series share the same
interrupt controller (INTC).
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4890/
Before we start adding the platform code we add the common include files.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4893/
