According to hwmon ABI, in%d_enable is a sysfs interface that
allows user space to enable and disable the input sensor. So
this patch just simply adds the attribute to the list.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When CONFIG_PM_SLEEP is disabled, we get a warning about unused
suspend/resume functions:
drivers/hwmon/ina3221.c:451:12: error: 'ina3221_resume' defined but not used [-Werror=unused-function]
static int ina3221_resume(struct device *dev)
drivers/hwmon/ina3221.c:428:12: error: 'ina3221_suspend' defined but not used [-Werror=unused-function]
static int ina3221_suspend(struct device *dev)
Picking the correct #ifdef check is hard, so let's remove
that check and instead mark the functions as __maybe_unused
to let the compiler silently drop them instead.
Fixes: 7de1ab9dac8e ("hwmon: (ina3221) Add suspend and resume functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
An ina3221 chip has three input ports. Each port is used
to measure the voltage and current of its input source.
The DT binding now has defined bindings for their input
sources, so the driver should read these information and
handle accordingly.
This patch adds a new structure of input source specific
information including input source label, shunt resistor
value and its connection status. It exposes these labels
via in[123]_label sysfs nodes upon available, and also
disables those channels where there are no input source
being connected. Meanwhile, it also adds in[123]_enable
sysfs nodes for users to get control of three channels,
and returns -ENODATA code for any sensor read according
to hwmon ABI.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Depending on the hardware design, an INA3221 chip might lose
its power during system suspend/resume. So this patch adds
a set of suspend and resume functions to cache the register
values including config register value and limit settings.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[groeck: Moved call to dev_set_drvdata()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The three INA3221_CONFIG_MODE macros are not correctly defined here.
The MODE3-1 bits are located at BIT 2-0 according to the datasheet.
So this patch just fixes them by shifting all of them with a correct
offset. However, this isn't a crital bug fix as the driver does not
use any of them at this point.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MSB (15th bit) of INA3221_CONFIG is a self-clear reset bit.
So this register should be added to the volatile_table of the
regmap_config. Otherwise, we will see this bit is sticky in the
regcache which might accidentally reset the chip when an actual
write happens to the register.
This might not be a severe bug for the current code line since
there's no second place touching the INA3221_CONFIG except the
reset routine in the probe().
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.
One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.
Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.
The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Probe deferrals aren't actual errors, so silence the error message in
case the PWM cannot yet be acquired.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The continue will not truely skip any code. hence it is safe to
remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6798D is, with the exception of fan and pwm channel configuration
registers, similar to other chips of the series. One interesting
difference is the chip ID, which is now extended to 13 bit (the 12-bit
chip ID value overlaps with the chip ID of NCT6797D).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for NCT6797D. With the exception of fan/pwm configuration
registers, it is mostly compatible with NCT6795D.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For NCT6795D and NCT6796D, the DIMM temperature sources are named
"Agent[01] Dimm [01]" per datasheet. Match names in datasheets to
avoid confusion.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that everything is separated, clean up fan and pwm configuration
for NCT6796D. While doing that, take the forgotten configuration register
cre0 into account to determine if AUXFANIN2 (fan5) and AUXFANOUT2 (pwm5)
are connected.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Separate fan/pwm configuration detection for NCT6795D into separate
case statement to make the code easier to read.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While detecting the configuration for multiple chips in one go reduces
code size, it also increases code complexity. Separate chip detection
to improve code readability. As first step, separate detection for
NCT6793D.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When determining support for a given fan or pwm control, the code is
easier to read if the necessary instructions are grouped together.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use
boolean |= <expression>;
instead of
if (!boolean)
boolean = <expression>;
to assign values to boolean variables.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declare and initialize LDN / chip specific configuration variables
earlier. This simplifies re-using the configuration variables for
multiple chips and makes the code easier to read.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Group configuration variable declarations and initialization together.
While this results in reading more registers than necessary for a given
chip, it improves code readability and simplifies extending the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using variables named after configuration registers makes it more obvious
which configuration register value is used, especially if more than one
configuration register value is used to determine a configuration detail.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use variable names from chip datasheets (crXX) instead of regval_XX
for configuration register variables. This is shorter and, together
with subsequent changes, makes the code easier to read.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A fan speed tolerance only makes sense if a fan target speed has been
configured in the first place. Otherwise we get odd output such as
fan1_target:0
fan1_tolerance:337500
Only display values other than 0 if a fan target speed has been configured.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Clang warns when the address of a pointer is used in a boolean context
as it will always return true.
drivers/hwmon/scmi-hwmon.c:59:24: warning: address of array
'sensor->name' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (sensor && sensor->name)
~~ ~~~~~~~~^~~~
1 warning generated.
Remove the check as it isn't doing anything currently; if validation
of the contents of the data structure was intended by the original
author (since this line has been present from the first version of
this driver), it can be added in a follow-up patch.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PTR_ERR_OR_ZERO has implemented the same function. We prefer to use
inlined function rather than code-opened implementation.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31725/MAX31726 are local temperature sensors with +/- 0.5 degree
Celsius accuracy and 16-bit (0.00390625 degrees Celsius) resolution.
They have a register mapping and encoding compatible with the lm75
series drivers. Address scan and extended temperature range are
not supported by this patch.
Tested on real hardware and verified temperature readings are correct.
Signed-off-by: Kun Yi <kunyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I removed the "dsw_en &&" chunk of the condition because we know that
"dsw_en" is set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
BIOS developer guides refer to Family 15h Models 60h-6fh and Family 15h
Models 70h-7fh. So far the driver only checked for Models 60h and 70h.
However, there are now processors with other model numbers in the same
families. Example is A10-9620P family 15h model 65h. Follow the developer
guides and mask the lower 4 bit of the model number to determine the
registers to use for reading temperatures and temperature limits.
Reported-by: Guglielmo Fanini <g.fanini@gmail.com>
Cc: Guglielmo Fanini <g.fanini@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking the child node names is pointless as the DT node name can
never be NULL, so remove it.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-hwmon@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calling devm_kstrdup() on a fixed string is unnecessary, as is validating
its contents. Rearrange the code to avoid both.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for LTM4686 Ultrathin Dual 10A or
Single 20A uModule Regulator with Digital Power System Management.
Datasheet: http://www.analog.com/ltm4686
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The documented register to retrieve the fan RPM for fan7 is found
to be unreliable at least with NCT6796D revision 3. Let's use
register 0x4ce instead. This is undocumented for NCT6796D, but
documented for NCT6797D and NCT6798D and known to be working.
Reported-by: Robert Kern <ulteq@web.de>
Cc: Robert Kern <ulteq@web.de>
Fixes: 81820059a4 ("hwmon: (nct6775) Add support for NCT6796D")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
fan7 on NCT6796D does not have a fan count register; it only has an RPM
register. Switch to using RPM registers to read the fan speed for all
chips supporting it to solve the problem for good.
Reported-by: Robert Kern <ulteq@web.de>
Cc: Robert Kern <ulteq@web.de>
Fixes: 81820059a4 ("hwmon: (nct6775) Add support for NCT6796D")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following kernel log message is reported for the nct6775 driver
on ASUS WS X299 SAGE.
nct6775: Found NCT6796D or compatible chip at 0x2e:0x290
nct6775 nct6775.656: Invalid temperature source 11 at index 0,
source register 0x100, temp register 0x73
nct6775 nct6775.656: Invalid temperature source 11 at index 2,
source register 0x300, temp register 0x77
nct6775 nct6775.656: Invalid temperature source 11 at index 3,
source register 0x800, temp register 0x79
nct6775 nct6775.656: Invalid temperature source 11 at index 4,
source register 0x900, temp register 0x7b
A recent version of the datasheet lists temperature source 11 as reserved.
However, an older version of the datasheet lists temperature sources 10
and 11 as supported virtual temperature sources. Apparently the older
version of the datasheet is correct, so list those temperature sources
as supported.
Virtual temperature sources are different than other temperature sources:
Values are not read from a temperature sensor, but written either from
BIOS or an embedded controller. As such, each virtual temperature has to
be reported. Since there is now more than one temperature source, we have
to keep virtual temperature sources in a chip-specific mask and can no
longer rely on the assumption that there is only one virtual temperature
source with a fixed index. This accounts for most of the complexity of this
patch.
Reported-by: Robert Kern <ulteq@web.de>
Cc: Robert Kern <ulteq@web.de>
Fixes: 81820059a4 ("hwmon: (nct6775) Add support for NCT6796D")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A few more fixes who have trickled in:
- MMC bus width fixup for some Allwinner platforms
- Fix for NULL deref in ti-aemif when no platform data is passed in
- Fix div by 0 in SCMI code
- Add a missing module alias in a new RPi driver
-----BEGIN PGP SIGNATURE-----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=oZbn
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few more fixes who have trickled in:
- MMC bus width fixup for some Allwinner platforms
- Fix for NULL deref in ti-aemif when no platform data is passed in
- Fix div by 0 in SCMI code
- Add a missing module alias in a new RPi driver"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
memory: ti-aemif: fix a potential NULL-pointer dereference
firmware: arm_scmi: fix divide by zero when sustained_perf_level is zero
hwmon: rpi: add module alias to raspberrypi-hwmon
arm64: allwinner: dts: h6: fix Pine H64 MMC bus width
Not all fans have a fan pulse register. This can result in reading
beyond the end of REG_FAN_PULSES and FAN_PULSE_SHIFT arrays,
and was reported by smatch as possible error.
1672 for (i = 0; i < ARRAY_SIZE(data->rpm); i++) {
^^^^^^^^^^^^^^^^^^^^^^^^
This is a 7 element array.
...
1685 data->fan_pulses[i] =
1686 (nct6775_read_value(data, data->REG_FAN_PULSES[i])
1687 >> data->FAN_PULSE_SHIFT[i]) & 0x03;
^^^^^^^^^^^^^^^^^^^^^^^^
FAN_PULSE_SHIFT is either 5 or 6
elements.
To fix the problem, we have to ensure that all REG_FAN_PULSES and
FAN_PULSE_SHIFT have the appropriate length, and that REG_FAN_PULSES
is only read if the register actually exists.
Fixes: 6c009501ff ("hwmon: (nct6775) Add support for NCT6102D/6106D")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is dead code because j can never be 1 at this point. We had
intended to just test if the bit was clear.
Fixes: bbd8decd41 ("hwmon: (nct6775) Add support for weighted fan control")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The raspberrypi-hwmon driver doesn't automatically load, although it does work
when loaded, by adding the alias it auto loads as expected when built as a
module. Tested on RPi2/RPi3 on 32 bit kernel and RPi3B+ on aarch64 with
Fedora 28 and a patched 4.18 RC kernel.
Fixes: 3c493c885cf ("hwmon: Add support for RPi voltage sensor")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
CC: Stefan Wahren <stefan.wahren@i2se.com>
CC: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
val can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
vers/hwmon/nct6775.c:2698 store_pwm_weight_temp_sel() warn: potential
spectre issue 'data->temp_src' [r]
Fix this by sanitizing val before using it to index data->temp_src
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475_read_word() function was meant to return negative error
codes on failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475_update_device() function returns error pointers. The
problem is that in show_pwmfreq() we dereference it before the check.
And then in pwm_use_point2_pwm_at_crit_show() there isn't a check at
all. I don't know if it's required, but it silences a static checker
warning and it's doesn't hurt anything to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----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=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
