For aesthetics. Shorten all the register names by removing '_REG' from all
of them.
This helps fix all the checkpatch.pl issues.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In case of error, the function of_io_request_and_map() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 847b8bf62eb4 ("rtc: sun6i: Expose the 32kHz oscillator")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
COMPILE_TEST was wrongly placed, move it to the "depends on" line.
Also depend on COMMON_CLK as the driver now needs it to be properly
compiled.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 847b8bf62eb4 ("rtc: sun6i: Expose the 32kHz oscillator") adds
a new clock for the rtc block with a 2 step probe mechanism. To share
the register region between both the clock and rtc instance, a static
pointer is used to keep the related data structure.
To preserve compatibility with the old binding, the data structure
should be saved as soon as the registers are mapped in, regardless
of the presence of the clock bindings, so that the rtc device can
retrieve it when it is probed.
This fixes the rtc device not probing when we use the updated driver
with an old device tree blob.
Fixes: 847b8bf62eb4 ("rtc: sun6i: Expose the 32kHz oscillator")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The clear of the LPTA_EN flag should be synced before writing to the
alarm register. Omitting this synchronization creates a race when
trying to change existing alarm.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The bq32000 includes a trickle charge circuit to maintain the charge of the
backup supply when a super capacitor is used.
You can enable the charging circuit by setting 'trickle-resistor-ohms',
additionally you can set TCFE to 1 to bypass the internal diode and boost
the charge voltage of the backup supply. You might want to enable/disable
the TCFE switch from userspace (e.g when device is only connected to a
battery)
This patch introduces a new sysfs entry to enable and disable this FET
form userspace.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now that we have a devm variant of rtc_device_register, switch to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC controls the input source of the main 32kHz oscillator in the
system, feeding it to the clock unit too.
By default, this is using an internal, very inaccurate (+/- 30%)
oscillator with a divider to make it roughly around 32kHz. This is however
quite impractical for the RTC, since our time will not be tracked properly.
Since this oscillator is an input of the main clock unit, and since that
clock unit will be probed using CLK_OF_DECLARE, we have to use it as well,
leading to a two stage probe: one to enable the clock, the other one to
enable the RTC.
There is also a slight change in the binding that is required (and should
have been from the beginning), since we'll need a phandle to the external
oscillator used on that board. We support the old binding by not allowing
to switch to the external oscillator and only using the internal one (which
was the previous behaviour) in the case where we're missing that phandle.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC is clocked from either an internal, imprecise, oscillator or an
external one, which is usually much more accurate.
The difference perceived between the time elapsed and the time reported by
the RTC is in a 10% scale, which prevents the RTC from being useful at all.
Fortunately, the external oscillator is reported to be mandatory in the
Allwinner datasheet, so we can just switch to it.
Cc: stable@vger.kernel.org
Fixes: 9765d2d943 ("rtc: sun6i: Add sun6i RTC driver")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Some registers have a read-modify-write access pattern that are not atomic.
Add some locking to prevent from concurrent accesses.
Cc: stable@vger.kernel.org
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since we have to provide the clock very early on, the RTC driver cannot be
built as a module. Make sure that won't happen.
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patches fixes comparison between signed and unsigned values as it
could produce an incorrect result when the signed value is converted to
unsigned:
drivers/rtc/rtc-stm32.c: In function 'stm32_rtc_valid_alrm':
drivers/rtc/rtc-stm32.c:404:21: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if ((((tm->tm_year > cur_year) &&
...
It also fixes comparison always true or false due to the fact that unsigned
value is compared against zero with >= or <:
drivers/rtc/rtc-stm32.c: In function 'stm32_rtc_init':
drivers/rtc/rtc-stm32.c:514:35: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
for (pred_a = pred_a_max; pred_a >= 0; pred_a-- ) {
drivers/rtc/rtc-stm32.c:530:44: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
(rate - ((pred_a + 1) * (pred_s + 1)) < 0) ?
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Using the ~ operator on a BIT() constant results in a large 'unsigned long'
constant that won't fit into an 'unsigned int' function argument on 64-bit
architectures, resulting in a harmless build warning in x86 allmodconfig:
drivers/rtc/rtc-stm32.c: In function 'stm32_rtc_probe':
drivers/rtc/rtc-stm32.c:651:51: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
regmap_update_bits(rtc->dbp, PWR_CR, PWR_CR_DBP, ~PWR_CR_DBP);
As PWR_CR_DBP mask prevents other bits to be cleared, replace all
~PWR_CR_DBP by 0.
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Accessing the registers of the RTC block on Tegra requires the module
clock to be enabled. This only works because the RTC module clock will
be enabled by default during early boot. However, because the clock is
unused, the CCF will disable it at late_init time. This causes the RTC
to become unusable afterwards. This can easily be reproduced by trying
to use the RTC:
$ hwclock --rtc /dev/rtc1
This will hang the system. I ran into this by following up on a report
by Martin Michlmayr that reboot wasn't working on Tegra210 systems. It
turns out that the rtc-tegra driver's ->shutdown() implementation will
hang the CPU, because of the disabled clock, before the system can be
rebooted.
What confused me for a while is that the same driver is used on prior
Tegra generations where the hang can not be observed. However, as Peter
De Schrijver pointed out, this is because on 32-bit Tegra chips the RTC
clock is enabled by the tegra20_timer.c clocksource driver, which uses
the RTC to provide a persistent clock. This code is never enabled on
64-bit Tegra because the persistent clock infrastructure does not exist
on 64-bit ARM.
The proper fix for this is to add proper clock handling to the RTC
driver in order to ensure that the clock is enabled when the driver
requires it. All device trees contain the clock already, therefore
no additional changes are required.
Reported-by: Martin Michlmayr <tbm@cyrius.com>
Acked-By Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ordering of includes is currently completely arbitrary, making it
impossible to decide where to put new includes. Remove the dilemma by
sort the include list alphabetically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The new driver has a stray #ifdef in it that causes a build error:
drivers/rtc/rtc-stm32.c:718:21: error: 'stm32_rtc_of_match' undeclared here (not in a function); did you mean 'stm32_rtc_pm_ops'?
As the #ifdef serves no purpose here, let's just remove it.
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The remove function can be called at runtime for a manual 'unbind'
operation and must not be left out from a built-in driver, as kbuild
complains:
`stm32_rtc_remove' referenced in section `.data.stm32_rtc_driver' of drivers/rtc/rtc-stm32.o: defined in discarded section `.exit.text' of drivers/rtc/rtc-stm32.o
This removes the extraneous annotation.
Fixes: 4e64350f42 ("rtc: add STM32 RTC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds support for the STM32 RTC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Armada38x wants to modify its rtc_class_ops to remove the interrupt
handling when there is no usable interrupt, but this means we leave
function pointers in writable memory.
Since rtc_class_ops is small, arrange to have two instances, one for
when we have interrupts, and one for when we have none, both marked
const. This allows the compiler to place them in read-only memory,
which is better than placing them in __ro_after_init.
Thanks to Bhumika Goyal <bhumirks@gmail.com> for pointing out that
the structure was writable and submitting a patch to add
__ro_after_init.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Declare rtc_class_ops structures as const as they are only passed
as an argument to the function devm_rtc_device_register. This argument
is of type const struct rtc_class_ops *, so rtc_class_ops structures
having this property can be declared const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct rtc_class_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
devm_rtc_device_register(...,&i@p,...)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct rtc_class_ops i;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The DryIce chipset has a dedicated security violation interrupt that is
triggered for security violations (if configured to do so). According
to the publicly available imx258 reference manual, irq 56 is used for
this interrupt.
If an irq number is provided for the security violation interrupt,
install the same handler that we're already using for the "normal"
interrupt.
imxdi->irq is used only in the probe function, make it a local variable.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds alarm support. This allows to configure the chip
to generate an interrupt when the alarm matches current time value.
Alarm can be programmed up to one year in the future
and is accurate to the second.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds support for saving/loading weekday value from the chip.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to RES-3124064:
The device supports CPU write and read access to the RTC time register.
However, due to this restriction, read and write from/to internal RTC
register may fail.
Workaround:
General setup:
1. Configure the RTC Mbus Bridge Timing Control register (offset 0x184A0)
to value 0xFD4D4FFF
Write RTC WRCLK Period to its maximum value (0x3FF)
Write RTC WRCLK setup to 0x29
Write RTC WRCLK High Time to 0x53 (default value)
Write RTC Read Output Delay to its maximum value (0x1F)
Mbus - Read All Byte Enable to 0x1 (default value)
2. Configure the RTC Test Configuration Register (offset 0xA381C) bit3
to '1' (Reserved, Marvell internal)
For any RTC register read operation:
1. Read the requested register 100 times.
2. Find the result that appears most frequently and use this result
as the correct value.
For any RTC register write operation:
1. Issue two dummy writes of 0x0 to the RTC Status register (offset
0xA3800).
2. Write the time to the RTC Time register (offset 0xA380C).
This patch is based on the work of Shaker Daibes
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fixes checkpatch.pl warning:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Vesa Jääskeläinen <vesa.jaaskelainen@vaisala.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Texas Instrument's TPS65910 has support for compensating RTC crystal
inaccuracies. When enabled every hour RTC counter value will be compensated
with two's complement value.
Signed-off-by: Vesa Jääskeläinen <vesa.jaaskelainen@vaisala.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system power
controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only
-----BEGIN PGP SIGNATURE-----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=z4SX
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- non-modular drivers are now explicitly non-modular
New driver:
- Epson Toyocom rtc-7301sf/dg
Drivers:
- cmos: reject unsupported alarm values wrt the RTC capabilities
- ds1307: ACPI support
- jz4740: DT support, jz4780 handling, can now be used as a system
power controller
- mcp795: many fixes, in particular proper month handling
- twl: driver is now DT only"
* tag 'rtc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (31 commits)
rtc: mcp795: Fix whitespace and indentation.
rtc: mcp795: Prefer using the BIT() macro.
rtc: mcp795: fix month write resetting date to 1.
rtc: mcp795: fix time range difference between linux and RTC chip.
rtc: mcp795: fix bitmask value for leap year (LP).
rtc: mcp795: use bcd2bin/bin2bcd.
rtc: add support for EPSON TOYOCOM RTC-7301SF/DG
rtc: ds1307: Add ACPI support
rtc: imxdi: (trivial) fix a typo
rtc: ds1374: Merge conditional + WARN_ON()
rtc: twl: make driver DT only
rtc: twl: kill static variables
rtc: fix typos in Kconfig
rtc: jz4740: make the driver builtin only
rtc: jz4740: remove unused EXPORT_SYMBOL
Documentation: bindings: fix twl-rtc documentation
rtc: Enable compile testing for Maxim and Samsung drivers
MIPS: jz4740: Remove obsolete code
MIPS: qi_lb60: Probe RTC driver from DT and use it as power controller
MIPS: jz4740: DTS: Probe the jz4740-rtc driver from devicetree
...
Fix whitespace and indentation errors and the following
checkpatch warnings:
- line 15: Block comments use a trailing */ on a separate line
- line 256: Line over 80 characters
No code change.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch doesn't change the code but replaces all bitmask values
with the BIT(x) macro.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According to Microchip errata some combinations of date and month
values may result in the date being reset to 1, even if the date
is also written with the month (for example 31-07 or 31-08).
As a workaround avoid writing date and month values within the same
Write command. Instead, terminate the Write command after loading
the date and begin a new command to write the month. In addition,
disable the oscillator before loading the new values. This is done
by ensuring both the ST and EXTOSC bits are cleared and waiting for
the OSCON bit to clear.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
In linux rtc_time struct, tm_mon range is 0~11, while in RTC HW REG,
month range is 1~12. This patch adjusts difference of them.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
According the datasheet the leap year is a fifth bit in month register.
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Change rtc-mcp795.c to use the bcd2bin/bin2bcd functions.
This change fixes the wrong conversion of month value
from binary to BCD (missing right shift operation for 10 month).
Signed-off-by: Emil Bartczak <emilbart@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This adds support for EPSON TOYOCOM RTC-7301SF/DG which has parallel
interface compatible with SRAM.
This driver supports basic clock, calendar and alarm functionality.
Tested with Microblaze linux running on Artix7 FPGA board with my own
custom IP for RTC-7301.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch enables ACPI support for rtc-ds1307 driver.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
WARN_ON does both these things in one statement.
Using a better pattern with WARN_ON().
Signed-off-by: Srikant Ritolia <s.ritolia@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since there are no platform based users and all users
of this code are TI OMAP-based which is DT only, it makes
sense to remove unused code.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The current code uses static variables which prevent
the use of multiple rtc twl instances.
We also make it clear that this driver supports only
TWL4030 and TWL6030 classes.
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Power management suspend/resume tracing (ab)uses the RTC to store
suspend/resume information persistently. As a consequence the RTC value is
clobbered when timekeeping is resumed and tries to inject the sleep time.
Commit a4f8f6667f ("timekeeping: Cap array access in timekeeping_debug")
plugged a out of bounds array access in the timekeeping debug code which
was caused by the clobbered RTC value, but we still use the clobbered RTC
value for sleep time injection into kernel timekeeping, which will result
in random adjustments depending on the stored "hash" value.
To prevent this keep track of the RTC clobbering and ignore the invalid RTC
timestamp at resume. If the system resumed successfully clear the flag,
which marks the RTC as unusable, warn the user about the RTC clobber and
recommend to adjust the RTC with 'ntpdate' or 'rdate'.
[jstultz: Fixed up pr_warn formating, and implemented suggestions from Ingo]
[ tglx: Rewrote changelog ]
Originally-from: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Xunlei Pang <xlpang@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1480372524-15181-3-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since the driver is now calling machine_halt() that is not exported, it has
to be built in the kernel. Building it as a module will fail at linking
time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
max8907, max77686 and s5m RTC drivers can be compile tested to increase
build coverage. The s5m-rtc uses REGMAP_IRQ so add this as explicit
dependency.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The 'system-power-controller' singleton entry can be used in the
devicetree node of the jz4740-rtc driver to specify that the driver is
granted the right to power off the system through the registers of the
RTC unit.
See the documentation for more details:
Documentation/devicetree/bindings/rtc/ingenic,jz4740-rtc.txt
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
