o Use correct l3 (ETH_IP or ETH_IPV6)protcol in case
of inband vlan. Because of incorrect protcol type driver
was setting incorrect opcode. This resulted in adapter calculating
checksum incorrectly.
o Updated driver version to 5.0.29
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size.
In case of LRO skb->len is aggregate of len of number of packets hence MSS
obtained using skb->len would be incorrect. Incorrect estimation of recv MSS
would lead to delayed acks in some traffic patterns (which sends two or three
packets and wait for ack and only then send remaining packets). This leads to
drop in performance. Hence we need to set gso_size to MSS obtained from firmware.
o This is fixed recently in firmware hence the MSS is obtained based on
capability. If fw is capable of sending the MSS then only driver sets the gso_size.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 0x3, 0x7, 0xF, 0x1F, 0x3F, 0x7F and 0xFF are the allowed capture masks.
o Updated driver version to 5.0.28
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Without failing probe, register netdevice when device is in FAILED state.
o Device will come up with minimum functionality.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- After FW reset, IP addresses need to be reprogrammed to FW for LRO to work. This
was not happening in context reset path. Fixed it here.
- Updated driver version to 5.0.27
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log dump status.
Remove unmatched qlcnic_api_unlock call.
Update version to 5.0.26.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Updated version number to 5.0.25
o Do not hold onto RESETTING_BIT for entire duration of LED/ beacon test.
Instead, just checking for RESETTING_BIT not set before sending config_led
command down to card.
o Take rtnl_lock instead of RESETTING_BIT for beacon test while sending
config_led command down to make sure interface cannot be brought up/ down.
o Allocate and free resources if interface is down before
sending the config_led command. This is to make sure config_led
command sending doesn't fail.
o Clear QLCNIC_LED_ENABLE bit if beacon/ LED test fails to start.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Argument list to CDRP function has become unmanageably long. Fix it by properly
declaring a struct that encompasses all the input and output parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beacon test flashes both port LEDs instead of just 1 LED of a port.
Updated driver version to 5.0.23.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading CRB registers(if reqd) before releasing the api lock.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLT entry for FW image region has changed for C0 cards.
Updated the driver to look at the right region in the FLT.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the QLogic drivers into drivers/net/ethernet/qlogic/ and
the necessary Kconfig and Makefile changes.
CC: Ron Mercer <ron.mercer@qlogic.com>
CC: Amit Kumar Salecha <amit.salecha@qlogic.com>
CC: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
