The OMAP gpio binding documention [1] states that the #interrupts-cells
property for gpio controllers should be 2. Currently, for OMAP3+ devices
the #interrupt-cells is set to 1. By setting this property to 2, it
allows clients to pass a 2nd parameter indicating the sensitivity (level
or edge) and polarity (high or low) of the interrupt. The OMAP gpio
controllers support these options and so update the #interrupt-cells
property for OMAP3+ devices to 2.
[1] Documentation/devicetree/bindings/gpio/gpio-omap.txt
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add the device-tree node for GPMC on OMAP2, OMAP4 and OMAP5 devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add SDMA controller binding for OMAP2+ devices and populate DMA client
information for SPI and MMC peripheral on OMAP3+ devices. Please note
that OMAP24xx devices do not have SPI and MMC bindings available yet and
so DMA client information is not populated.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add usb otg data node in omap4/omap3 device tree file. Also update
the node with board specific setting in omapx-<board>.dts file.
The dt data specifies among others the interface type (ULPI or UTMI),
mode which is mostly OTG, power that specifies the amount of power
this can supply when in host mode.
The information about usb otg node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add omap-usb2 data node in omap4 device tree file. Since omap-usb2
is connected to ocp2scp, omap-usb2 dt data is added as a child node
of ocp2scp. The information about this data node is availabe @
Documentation/devicetree/bindings/usb/usb-phy.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add omap control usb data in omap4 device tree file. This will have the
register address of registers to power on the PHY and to write to
mailbox. The information about this data node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
For OMAP4 devices, timers 5-8 have both a L3 bus address and a Cortex-A9
private bus address. Currently the device-tree source only contains the
L3 bus address for these timers. Update these timers to include the
Cortex-A9 private address and make the default address the Cortex-A9
private bus address to match the current HWMOD implementation.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Adds the counter-32k timers nodes present in OMAP2/3/4 devices and
device-tree binding documentation for OMAP counter-32k.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add the 12 GP timers nodes present in OMAP2.
Add the 12 GP timers nodes present in OMAP3.
Add the 11 GP timers nodes present in OMAP4.
Add the 7 GP timers nodes present in AM33xx.
Add documentation for timer properties specific to OMAP.
Thanks to Vaibhav Hiremath for creating the AM33xx timer nodes. I have modified
Vaibhav's original nodes adding information on which timers support a PWM
output.
V5 changes:
- Updated timer register sizes for OMAP2/3/4.
- Modified AM335x timer register size to be 1KB instead of 4KB to align with
HWMOD.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-Reviewed-&-Tested-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
The interrupt-parent attribute does not have to be added in each
node since the fmwk will check for the parent as well to get it.
Create an interrupt-parent for OMAP2, OMAP3, AM33xx and remove the
attributes from every nodes that were using it.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sebastien Guiriec <s-guiriec@ti.com>
*reg* property for ocp2scp was previously obtained from ti,hwmods property.
But that is now explicitly added to the dt node.
Also updated the documentation with *reg* info.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
Add pinctrl driver entries for omap2+. These all use
the generic pinctrl-single driver for the padconf
registers.
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: updated to drop omap2420.dtsi rename changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Thanks to Vaibhav <hvaibhav@ti.com> omap_device fix
(ARM: OMAP: omap_device: Fix up resource names when booted with devicetre),
we can now specify reg and interrupts using standard device tree
attributes.
Update the OMAP4 dtsi file with missing reg and interrupts attributes.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
In order to get the memory areas by name when booted with DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Create the sections describing the McBSP ports to be able to use them via
DT.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Remove some useless comment and move GIC controller outside
of the OCP node since it does use the MPU internal bus and
not the OCP.
This will not change the functionality but will reflect the
reality more accurately.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add cortex-a9 local timer support for all OMAP4 based
SOCs using DT.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Provide PL310 Level 2 Cache Controller Device Tree
support for OMAP4 based devices.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Device tree data for the EMIF sdram controllers in OMAP4
and LPDDR2 memory devices attached to OMAP4 boards.
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
[santosh.shilimkar@ti.com: Rebased against 3.6-rc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[b-cousson@ti.com: Use label in board to access EMIF nodes]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add keypad data node in omap4 device tree file.
Also fill the device tree binding parameters
with the required value in "omap4-sdp" dts file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[b-cousson@ti.com: Re-align the entries and the comments]
Add ocp2scp data node in omap4 device tree file.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DMIC IP is used to connect up to 6 digital microphones directly to OMAP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McPDM is used on OMAP4 based boards to communicate with an external audio
codec (twl6040).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP mmc related device tree data for OMAP4.
Currenly limited to only omap4-panda and omap4-sdp
boards.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add the 4 McSPI controller nodes present in an OMAP4 device.
Remove SPI static device initialisation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
The GIC binding was updated in 3.2 and expects 3 interrupt-cells.
- Update the #interrupt-cells
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add i2c controllers nodes into the main ocp bus.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Follow the DTS convention and thus name the nodes <name>@<address> without
any '0x' prefix in the physical address.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Pass minimal data needed for console boot, from dt, for
OMAP4 panda/sdp and OMAP3 beagle boards, and get rid of the
static initialization from generic board file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for devices used by PM code (mpu, dsp, iva).
Add a cpus node as well as recommended in the DT spec.
Remove mpu, dsp, iva devices init if is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Kevin Hilman <khilman@ti.com>
Used the main OCP node to add bindings with the l3_noc driver.
Remove l3_noc static device creation if DT is populated.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add initial device-tree support for OMAP4 SoC.
This is based on the original panda board patch done by Manju:
http://permalink.gmane.org/gmane.linux.ports.arm.omap/60393
Add the generic GIC interrupt-controller from ARM.
Add an empty "soc" node to contain non memory mapped IPs
(DSP, MPU, IPU...).
Note: Since reg, irq and dma are provided by hwmod for the
moment, these attributes will not be present at all in DTS
to highlight the gap. They will be added as soon as dma bindings
will be there and drivers will be adapted.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
