The HVS FIFOs are currently assigned each time we have an atomic_check
for all the enabled CRTCs.
However, if we are running multiple outputs in parallel and we happen to
disable the first (by index) CRTC, we end up changing the assigned FIFO
of the second CRTC without disabling and reenabling the pixelvalve which
ends up in a stall and eventually a VBLANK timeout.
In order to fix this, we can create a special value for our assigned
channel to mark it as disabled, and if our CRTC already had an assigned
channel in its previous state, we keep on using it.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923084032.218619-2-maxime@cerno.tech
The current CRTC state reset hook in vc4 allocates a vc4_crtc_state
structure as a drm_crtc_state, and relies on the fact that vc4_crtc_state
embeds drm_crtc_state as its first member, and therefore can be safely
cast.
However, this is pretty fragile especially since there's no check for this
in place, and we're going to need to access vc4_crtc_state member at reset
so this looks like a good occasion to make it more robust.
Fixes: 6d6e500391 ("drm/vc4: Allocate the right amount of space for boot-time CRTC state.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923084032.218619-1-maxime@cerno.tech
The HVS has three FIFOs that can be assigned to a number of PixelValves
through a mux.
However, changing that FIFO requires that we disable and then enable the
pixelvalve, so we want to assign FIFOs to all the enabled CRTCs, and not
just the active ones.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200918145918.101068-1-maxime@cerno.tech
The vc4 display engine has a first controller called the HVS that will
perform the composition of the planes. That HVS has 3 FIFOs and can
therefore compose planes for up to three outputs. The timings part is
generated through a component called the Pixel Valve, and the BCM2711 has 6
of them.
Thus, the HVS has some bits to control which FIFO gets output to which
Pixel Valve. The current code supports that muxing by looking at all the
CRTCs in a new DRM atomic state in atomic_check, and given the set of
constraints that we have, assigns FIFOs to CRTCs or reject the mode
entirely. The actual muxing will occur during atomic_commit.
However, that doesn't work if only a fraction of the CRTCs' state is
updated in that state, since it will ignore the CRTCs that are kept running
unmodified, and will thus unassign its associated FIFO, and later disable
it.
In order to make the code work as expected, let's pull the CRTC state of
all the enabled CRTC in our atomic_check so that we can operate on all the
running CRTCs, no matter whether they are affected by the new state or not.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917121623.42023-1-maxime@cerno.tech
Handing the return value of drm_universal_plane_init to fix the following
W=1 kernel build warning(s):
vc4_plane.c: In function ‘vc4_plane_init’:
vc4_plane.c:1340:6: warning: variable ‘ret’ set but not
used [-Wunused-but-set-variable]
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1599811777-34093-1-git-send-email-tiantao6@hisilicon.com
Clang warns:
drivers/gpu/drm/vc4/vc4_plane.c:901:27: warning: operator '?:' has lower
precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
fb->format->has_alpha ?
~~~~~~~~~~~~~~~~~~~~~ ^
drivers/gpu/drm/vc4/vc4_plane.c:901:27: note: place parentheses around
the '|' expression to silence this warning
fb->format->has_alpha ?
~~~~~~~~~~~~~~~~~~~~~ ^
drivers/gpu/drm/vc4/vc4_plane.c:901:27: note: place parentheses around
the '?:' expression to evaluate it first
fb->format->has_alpha ?
~~~~~~~~~~~~~~~~~~~~~~^
1 warning generated.
Add the parentheses as that was clearly intended, otherwise
SCALER5_CTL2_ALPHA_PREMULT won't be added to the list.
Fixes: c54619b0bf ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1150
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910171831.4112580-1-natechancellor@gmail.com
Clang warns 100+ times in the vc4 driver along the lines of:
drivers/gpu/drm/vc4/vc4_hdmi_phy.c:518:13: warning: implicit conversion
from enumeration type 'enum vc4_hdmi_field' to different enumeration
type 'enum vc4_hdmi_regs' [-Wenum-conversion]
HDMI_WRITE(HDMI_TX_PHY_POWERDOWN_CTL,
~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
The HDMI_READ and HDMI_WRITE macros pass in enumerators of type
vc4_hdmi_field but vc4_hdmi_write and vc4_hdmi_read expect a enumerator
of type vc4_hdmi_regs, causing a warning for every instance of this.
Update the parameter type so there is no more mismatch.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1149
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910170401.3857250-1-natechancellor@gmail.com
The variant->registers[] has ->num_registers elements so the >
comparison needs to be changes to >= to prevent an out of bounds
access.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910100748.GA79916@mwanda
The BCM2711 has a reworked display pipeline, and the load tracker needs
some adjustment to operate properly. Let's add a compatible for BCM2711
and disable the load tracker until properly supported.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/beac4f9ef0261bca731a0402c8354e9af740519c.1599120059.git-series.maxime@cerno.tech
In order to avoid pixels getting stuck in an unflushable FIFO, we need when
we disable the HDMI controller to switch away from getting our pixels from
the pixelvalve and instead use blank pixels, and switch back to the
pixelvalve when we enable the HDMI controller.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fde3efb1ad79f4476a73d310cbba3ec07dc6dabe.1599120059.git-series.maxime@cerno.tech
The VID_CTL setup is done in several places in the driver even though it's
not really required. Let's simplify it a bit to do the configuration in one
go.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/08e7ebb605a560fcc149b69b4af52753a7870b2f.1599120059.git-series.maxime@cerno.tech
In order to prevent some pixels getting stuck in an unflushable FIFO on
bcm2711, we need to enable the HVS, the pixelvalve (the CRTC) and the HDMI
controller (the encoder) in an intertwined way, and with tight delays.
However, the atomic callbacks don't really provide a way to work with
either constraints, so we need to roll our own callbacks so that we can
provide those guarantees.
Since those callbacks have been implemented and called in the CRTC code, we
can just implement them in the HDMI driver now.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2e9226d971117065f3b97e597f04f7fe2f0c134c.1599120059.git-series.maxime@cerno.tech
In order to avoid a pixel getting stuck in an unflushable FIFO, we need to
recenter the FIFO every time we're doing a modeset and not only if we're
connected to an HDMI monitor.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b3faaf05ac6c4d3c364d28fa441571eb85903269.1599120059.git-series.maxime@cerno.tech
The current code has some logic, disabled by default, to dump the register
setup in the HDMI controller.
However, since we're going to split those functions in multiple, shorter,
functions that only make sense where they are called in sequence, keeping
the register dump makes little sense.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c8c8d388f2d32fc3536336be36d003a862487eb7.1599120059.git-series.maxime@cerno.tech
The HDMI driver was registering a single ALSA card so far with the name
vc4-hdmi.
Obviously, this is not going to work anymore when we will have multiple
HDMI controllers since we will end up trying to register two files with the
same name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e60a37444e848a384a45707a21d6df8883115f86.1599120059.git-series.maxime@cerno.tech
The audio configuration has changed for the BCM2711, with notably a
different parent clock and a different channel configuration.
Make that modular to be able to support the BCM2711.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/85a8ca721c2d800be758c55870cea98536749680.1599120059.git-series.maxime@cerno.tech
ALSA's iec958 plugin by default sets the block start preamble
to 8, whilst this driver was programming the hardware to expect
0xF.
Amend the hardware config to match ALSA.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d0b126deb228baf1244c91e02ac0a8f7c9c60dc5.1599120059.git-series.maxime@cerno.tech
If the encoder is disabled and re-enabled (eg mode change) all infoframes
are reset, whilst the audio subsystem know nothing about this change.
The driver therefore needs to reinstate the audio infoframe for
itself.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cd579ccc2c9b9d2fce0ebaf32f847cedb0e4a7a2.1599120059.git-series.maxime@cerno.tech
The register range used for audio setup in the previous generations of
SoC were always the second range in the device tree. However, now that
the BCM2711 has way more register ranges, it makes sense to retrieve it
by names for it, while preserving the id-based lookup as a fallback.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a1ba5605fe1006a1ead5262ef3d66ea5d0750381.1599120059.git-series.maxime@cerno.tech
The HSM clock needs to be running at 101% the pixel clock of the HDMI
controller, however it's shared between the two HDMI controllers, which
means that if the resolutions are different between the two HDMI
controllers, and the lowest resolution is on the second (in enable order)
controller, the first HDMI controller will end up with a smaller than
expected clock rate.
Since we don't really need an exact frequency there, we can simply change
the minimum rate we expect instead.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/821992209cc0d7a83254bf26fe2bf507ef0994d2.1599120059.git-series.maxime@cerno.tech
The HSM clock needs to be setup at around 101% of the pixel rate. This
was done previously by setting the clock rate to 163.7MHz at probe time and
only check in mode_valid whether the mode pixel clock was under the pixel
clock +1% or not.
However, with 4k we need to change that frequency to a higher frequency
than 163.7MHz, and yet want to have the lowest clock as possible to have a
decent power saving.
Let's change that logic a bit by setting the clock rate of the HSM clock
to the pixel rate at encoder_enable time. This would work for the
BCM2711 that support 4k resolutions and has a clock that can provide it,
but we still have to take care of a 4k panel plugged on a BCM283x SoCs
that wouldn't be able to use those modes, so let's define the limit in
the variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7e692ddc231d33dd671e70ea04dd1dcf56c1ecb3.1599120059.git-series.maxime@cerno.tech
The mode_valid hook on the encoder uses a pointer to a drm_encoder called
crtc, which is pretty confusing. Let's rename it to encoder to make it
clear what it is.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7fbabab03992efe4a3a3640ac5ee2bb49b1c7338.1599120059.git-series.maxime@cerno.tech
Similarly to the audio support, CEC support is not there yet for the
BCM2711, so let's skip entirely the CEC initialization through a variant
flag.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bd0c4afa83b4e121692352cdc2dd1886162c7552.1599120059.git-series.maxime@cerno.tech
The CEC init code was put directly into the bind function, which was quite
inconsistent with how the audio support was done, and would prevent us from
further changes to skip that initialisation entirely.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/21f4717e076291522d0784a7fd3774d8e97eaf01.1599120059.git-series.maxime@cerno.tech
The HDMI driver was registering a single debugfs file so far with the name
hdmi_regs.
Obviously, this is not going to work anymore when will have multiple HDMI
controllers since we will end up trying to register two files with the same
name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9505c1eb40b3ef3709277bf9e8af77917b249c32.1599120059.git-series.maxime@cerno.tech
The vc4 CRTC will use the encoder type to control its output clock
muxing. However, this will be different from HDMI0 to HDMI1, so let's
store our type in the variant structure so that we can support multiple
controllers later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2736a86b498551ba9dbc5803c5bb910627a2550c.1599120059.git-series.maxime@cerno.tech
Similarly to the previous patches, the timings setup in the HDMI controller
of the BCM2711 is slightly different, mostly because it supports higher
resolutions and thus needed more spaces for the various timings, resulting
in the register layout changing.
Let's add a callback for that as well.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0cfcbb379212f90b4abc76c0ccf3b90d1d7c0268.1599120059.git-series.maxime@cerno.tech
Similarly to the previous patches, the CSC setup is slightly different in
the BCM2711 than in the previous generations. Let's add a callback for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5c19bbf10153cb42ca0fb67e08606c8295c17236.1599120059.git-series.maxime@cerno.tech
The HDMI PHY in the BCM2711 HDMI controller is significantly more
complicated to setup than in the older BCM283x SoCs.
Let's add hooks to enable and disable the PHY.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7216826284dbc60a58bdacd662805d20699e5c80.1599120059.git-series.maxime@cerno.tech
The BCM2711 and BCM283x HDMI controllers use a slightly different reset
sequence, so let's add a callback to reset the controller.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a34bcb493da07eae58ed704f65e72ce0748e8952.1599120059.git-series.maxime@cerno.tech
The HDMI controllers found in the BCM2711 have most of the registers
reorganized in multiple registers areas and at different offsets than
previously found.
The logic however remains pretty much the same, so it doesn't really make
sense to create a whole new driver and we should share the code as much as
possible.
Let's implement some indirection to wrap around a register and depending on
the variant will lookup the associated register on that particular variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3070236daff920e7edd11c5a72ac31fd0f6a656b.1599120059.git-series.maxime@cerno.tech
The HDMI controllers found in the BCM2711 has a pretty different clock and
registers areas than found in the older BCM283x SoCs.
Let's create a variant structure to store the various adjustments we'll
need later on, and a function to get the resources needed for one
particular version.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/71cfa3ce3d865bbab52a0e5651bc052dc4893f11.1599120059.git-series.maxime@cerno.tech
The vc4_hdmi_connector was only used to switch between drm_connector to
drm_encoder. However, we can now use vc4_hdmi to do the switch, so that
structure is redundant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/aee5120728db350b19c074de4290eafaf01e6671.1599120059.git-series.maxime@cerno.tech
The unbind function needs to retrieve a vc4_hdmi structure pointer through
the struct device that we're given since we want to support multiple HDMI
controllers.
However, our optional ASoC support doesn't make that trivial since it will
overwrite the device drvdata if we use it, but obviously won't if we don't
use it.
Let's make sure the fields are at the proper offset to be able to cast
between the snd_soc_card structure and the vc4_hdmi structure
transparently so we can support both cases.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/717082cba06b5c06280f26c56c08aee512365ed3.1599120059.git-series.maxime@cerno.tech
Our CEC code also retrieves the associated vc4_hdmi by setting the
vc4_dev pointer as its private data, and then dereferences its vc4_hdmi
pointer.
In order to eventually get rid of that pointer, we can simply pass the
vc4_hdmi pointer directly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/cb575cb9e13018bce131b8535e5b572dc1027877.1599120059.git-series.maxime@cerno.tech
Whenever the code needs to access the vc4_hdmi structure from a DRM
connector or encoder, it first accesses the drm_device associated to the
connector, then retrieve the drm_dev private data which gives it a
pointer to our vc4_dev, and will finally follow the vc4_hdmi pointer in
that structure.
That will also give us some trouble when having multiple controllers,
but now that we have our encoder and connector structures that are part
of vc4_hdmi, we can simply call container_of on the DRM connector or
encoder and retrieve the vc4_hdmi structure directly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/536ecce5898ea75839fa3788b876009d69a5ccae.1599120059.git-series.maxime@cerno.tech
The function vc4_hdmi_connector_detect access its vc4_hdmi struct by
dereferencing the pointer in the structure vc4_dev. This will cause some
issues when we will have multiple HDMI controllers, so let's just use the
local variable for now instead of dereferencing that pointer all the time,
and we'll fix the local variable later.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/ef92c5582d3b2894128b2272a8ada7cbc20be3d9.1599120059.git-series.maxime@cerno.tech
The current driver only supports a single HDMI controller, and part of
the issue is that the main vc4_dev structure holds a pointer to its
(only) HDMI controller, and the HDMI registers accessors will use it to
retrieve the mapped addresses.
Let's modify those accessors to use directly the vc4_hdmi structure so
that we can eventually get rid of that single global pointer.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/886b955586264ce078d7d35e9b8ef9ae51675c27.1599120059.git-series.maxime@cerno.tech
The driver isn't consistent with the name given to the vc4_hdmi
structure pointer in its functions. Make sure to use a consistent name.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/696be840dc427245afe94b43e0b829c728d948a7.1599120059.git-series.maxime@cerno.tech
Now that we are passing the vc4_hdmi structure to the connector init
function, we can simply use the pointer in that structure instead of
having the pointer as an argument.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/4fe1b45fe45e4ba57d40154da010807d4e5db86c.1599120059.git-series.maxime@cerno.tech
the vc4_hdmi driver has some custom structures to hold the data it needs to
associate with the drm_encoder and drm_connector structures.
However, it allocates them separately from the vc4_hdmi structure which
makes it more complicated than it needs to be.
Move those structures to be contained by vc4_hdmi and update the code
accordingly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/93b418d63c876355af2b3d3afebe31a256268623.1599120059.git-series.maxime@cerno.tech
We're calling vc4_debugfs_add_file with our struct vc4_hdmi pointer set
in the private field, but we don't use that field and go through the
main struct vc4_dev to get it.
Let's use the private field directly, that will save us some trouble
later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/24028dc06c379dbc71f98e027cce2839fdd446ce.1599120059.git-series.maxime@cerno.tech
