bnx2_has_work()'s logic is flawed and can cause the driver to miss
a link event. The fix is to compare the status block's attn_bits
and attn_bits_ack to determine if there is a link event.
Update version to 1.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Handle aborting a command after it is sent
IB/mthca: Fix thinko in init_mr_table()
RDMA/cxgb3: Fix resource leak in cxio_hal_init_ctrl_qp()
nmi_cpu_setup() is called from hardirq context and acquires oprofilefs_lock.
alloc_event_buffer() and oprofilefs_ulong_from_user() acquire this lock
without disabling irqs, which could deadlock.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: NCQ is broken on Maxtor 6L250S0
pata_pdc202xx_old: LBA48 bug
libata: IDENTIFY backwards for drive side cable detection
ahci.c: walkaround for SB600 SATA internal error issue
[libata] Disable ACPI by default; fix namespace problems
Fix section mismatch warning by moving data into __devinitdata section.
Add __devinit to initialization functions.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking for allocated DVMA memory and granted IRQ line.
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In this driver, the default ethernet address is first set by by calling
eth_port_uc_addr_get() which reads the relevant registers of the
corresponding port as initially set by firmware. However that function
used the port_num field accessed through the private area of net_dev
before it was set.
The result was that one board I have ended up with the unicast address
set to 00:00:00:00:00:00 (only port 1 is connected on this board). The
problem appeared after commit 84dd619e4d.
This patch fixes the bug by setting mp->port_num prior to calling
eth_port_uc_get_addr().
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The tx timeout routine was waking the tx queue conditionally. However,
it must call it unconditionally since the dev_watchdog has halted the tx
queue before calling the timeout function.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The nic poll routine was missing the call to the optimized irq routine.
This patch adds the missing call for the optimized path.
See http://bugzilla.kernel.org/show_bug.cgi?id=7950 for more information.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed rx checksum bits. Turn on TCP processing for rx checksum.
Fixed max frame length register write. It wasn't getting set
in multi-port system. Set rx buffer queue length properly
for jumbo frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the rx queue pointer when exiting NAPI poll rather than
at the end of each iteration. Remove unnecessary PCI flushes
that occurred after every write. Now write all regs and
flush once.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This was removed in a previous patch to increase performance, but
caused a transmit error for the 4032 chip.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original vendor driver contained a private ether_crc_le() function
that produced an inverted crc. When we changed to the kernel version of
ether_crc_le(), we neglected to undo the inversion. Let's do it now.
Discovered by and patch proffered by Jose Alberto Reguero.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correctly detect when TSO should be used on transmit by looking at the
skb->gso_size rather than seeing if the frame was larger than our MTU.
The old method causes problems when a host with a large (jumbo) MTU is
sending to a host with a small (standard) MTU.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With this applied, my machine has stopped all those painful messages.
dmesg now says :
root@riri:/Kernels# dmesg | grep LBA
ata1.00: 490234752 sectors, multi 0: LBA48 NCQ (not used)
ata2.00: 640 sectors, multi 1: LBA
ata3.00: 490234752 sectors, multi 0: LBA48 NCQ (not used)
Signed-off-by: Paul Rolland <rol@as2917.net>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In LBA48 mode we have to help the controller to get anything to work. The
chip provides a register giving word counts meant for ATAPI use which we
can use. However we need to load the count in words not bytes..
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For drive side cable detection to work correctly, drives need to be
identified backwards such that the slave device releases PDIAG- before
the mater drive tries to detect cable type. ata_bus_probe() was fixed
by commit f31f0cc2f0 but the new EH path
wasn't fixed. This patch makes new EH path do IDENTIFY backwards.
ata_dev_configure() for new devices are still performed master first.
This is to keep the detection messages in forward order.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is a HW issue in ATI SB600 SATA that PxSERR.E should not be
set on some conditions, for example, when there is no media in SATA
CD/DVD drive or media is not ready, AHCI controller fails to execute
ATAPI commands and reports PORT_IRQ_TF_ERR, but ATI SB600 SATA
controller sets PxSERR.E at the
same time, which is not necessary.
This patch is just to ignore the INTERNAL ERROR in such case.
Without this patch, ahci error handler will report many errors as
below:
----------- cut from dmesg -----------
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x0 data 0
res 51/24:03:00:00:20/00:00:00:00:00/a0 Emask 0x40 (internal error)
ata9: soft resetting port
ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata9.00: configured for UDMA/33
ata9: EH complete
ata9.00: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x2
ata9.00: (irq_stat 0x40000001)
ata9.00: cmd a0/01:00:00:00:00/00:00:00:00:00/a0 tag 0 cdb 0x43 data 12 in
res 51/24:03:00:00:00/00:00:00:00:00/a0 Emask 0x40 (internal error)
-------- end cut ---------
Signed-off-by: Conke Hu <conke.hu@amd.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not yet ready to turn on ATA ACPI by default, for either PATA or SATA.
Also, rename the global-scope module parameter variable 'noacpi' to
something more libata-specific, reducing the potential for namespace
collision.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent changes in the specs that were introduced in commit
740ac4fb08 were incorrect and resulted in machine check
errors on the PPC architecture for G PHY's with a revision number equal to 1. The
two offending changes are reverted.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a duplicated leftshift in bcm43xx_radio_set_tx_iq. data_high values are
already leftshifted. Thanks to Michael Buesch for spotting this.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places where the PHY version and revision were interchanged.
These are changed in the specifications on 2/13/07 and now use "analog" instead
instead of "version" to help reduce confusion.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://kvm.qumranet.com/home/avi/kvm:
KVM: always reload segment selectors
KVM: Prevent system selectors leaking into guest on real->protected mode transition on vmx
I2O subsystem has been broken in mainstream several months ago (after
2.6.18). Commit 4aff5e2333 from Jens
Axboe split struct request ->flags into two parts: cmd_type and
cmd_flags.
In i2o layer this patch has replaced flag REQ_SPECIAL by the according
cmd_type. However i2o has used REQ_SPECIAL not as command type but as
driver-specific flag for the debug purposes. As result all i2o requests
have type "special" now, are not processed to the hardware and fail with
I/O error:
i2o/hda:<3>Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
Buffer I/O error on device i2o/hda, logical block 0
unable to read partition table
block-osm: device added (TID: 207): i2o/hda
The following patch removes the extra debug checks without any drawbacks and
restores the normal driver's work.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Acked-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:eisa_root_register from .text between 'pci_eisa_init' (at offset 0xabf670) and 'virtual_eisa_release'
AFAIK a PCI to EISA bridge isn't anything hotpluggable, so
pci_eisa_init() can become __init.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_register_master from .text between 'spi_bitbang_start' (at offset 0x84e11a) and 'bitbang_work'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_alloc_master from .text between 'butterfly_attach' (at offset 0x84e681) and 'at25_remove'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:spi_new_device from .text between 'butterfly_attach' (at offset 0x84e7e4) and 'at25_remove'
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Bob's machine clocksource is selecting PIT over the ACPI PM timer,
because he has the PIIX4 bug. That bug drops the ACPI PM timers rating
to the same as the PIT, so that's why you're getting the PIT.
Realistically, the PIT is much slower then even the triple read ACPI PM,
so the de-ranking code is probably dropping it too far.
So don't drop ACPI PM quite so low if we see the PIIX4 bug.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Bob Tracy <rct@gherkin.frus.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d720bc4b8f partially removed a
private implementation of baud speed decoding. However it doesn't seem
to be complete: after the speed is decoded, it is still being used as an
index to a local speed table (array overrun, no doubt).
This was found by Graham Murray who noticed it caused a 2.6.19 regression
with the SX driver: https://bugs.gentoo.org/170554
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... still not sure why we need this ....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If this mddev and queue got reused for another array that doesn't register a
congested_fn, this function would get called incorretly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All that is missing the the function pointers in raid4_pers.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo reported it on lkml in the thread
"2.6.21-rc5: maxcpus=1 crash in cpufreq: kernel BUG at drivers/cpufreq/cpufreq.c:82!"
This check added to remove_dev is symmetric to one in add_dev and handles
callbacks for offline cpus cleanly.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
failed VM entry on VMX might still change %fs or %gs, thus make sure
that KVM always reloads the segment selectors. This is crutial on both
x86 and x86_64: x86 has __KERNEL_PDA in %fs on which things like
'current' depends and x86_64 has 0 there and needs MSR_GS_BASE to work.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Intel virtualization extensions do not support virtualizing real mode. So
kvm uses virtualized vm86 mode to run real mode code. Unfortunately, this
virtualized vm86 mode does not support the so called "big real" mode, where
the segment selector and base do not agree with each other according to the
real mode rules (base == selector << 4).
To work around this, kvm checks whether a selector/base pair violates the
virtualized vm86 rules, and if so, forces it into conformance. On a
transition back to protected mode, if we see that the guest did not touch
a forced segment, we restore it back to the original protected mode value.
This pile of hacks breaks down if the gdt has changed in real mode, as it
can cause a segment selector to point to a system descriptor instead of a
normal data segment. In fact, this happens with the Windows bootloader
and the qemu acpi bios, where a protected mode memcpy routine issues an
innocent 'pop %es' and traps on an attempt to load a system descriptor.
"Fix" by checking if the to-be-restored selector points at a system segment,
and if so, coercing it into a normal data segment. The long term solution,
of course, is to abandon vm86 mode and use emulation for big real mode.
Signed-off-by: Avi Kivity <avi@qumranet.com>
After freeing a block there should be no reference to this block.
Signed-off-by: Thomas Viehweger <Thomas.Viehweger@marconi.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Returning -1 causes the probe to stop, but it should just continue
instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix several instances of dvb-core functions using mutex_lock_interruptible
and returning -ERESTARTSYS where the calling function will either never
retry or never check the return value.
These cause a race condition with dvb_dmxdev_filter_free and
dvb_dvr_release, both of which are filesystem release functions whose
return value is ignored and will never be retried. When this happens it
becomes impossible to open dvr0 again (-EBUSY) since it has not been
released properly.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-By: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All the radio drivers need video_dev, but they were depending on
VIDEO_DEV!=n. That meant that one could try to compile the driver into
the kernel when VIDEO_DEV=m, which will not work. If video_dev is a
module, then the radio drivers must be modules too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The determination of whether the DAC has inverted cursor logic is
broken, import the version checks the X.org driver uses to fix this.
Next, when we change the timing generator, borrow code from X.org that
does 10 NOP reads of the timing generator register afterwards to make
sure the video-enable transition occurs cleanly.
Finally, use macros for the DAC registers and fields in order to
provide documentation for the next person who reads this code.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCSI midlayer may abort a command that was already sent. If the
initiator is still trying to send the command (or data-out PDUs for
that command), the QP may time out after the midlayer times
out. Therefore, when aborting the command, iSER may still have
references for the command's buffers. When sending these PDUs, the
sends will complete with an error and their resources will be released
then.
Signed-off-by: Erez Zilber <erezz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit c20e20ab ("IB/mthca: Merge MR and FMR space on 64-bit systems")
swapped the number of MTTs and MPTs when initializing the MR table. As
a result, we get a kernel oops when the number of MTT segments
allocated exceeds 0x20000.
Noted by Troy Benjegerdes <troy@scl.ameslab.gov>, and reproduced by
Dotan Barak <dotanb@mellanox.co.il>. This fixes
https://bugs.openfabrics.org/show_bug.cgi?id=490
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This was spotted by the Coverity checker (CID 1554).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the Kconfig files so that the Freescale QE options are automatically
selected if a QE device is selected. Previously, you'd need to manually
select UCC_FAST if you want any "fast" UCC devices, such as Gigabit Ethernet.
Now, the QE Gigabit Ethernet option is always available if the device has a
QE, and UCC_FAST is automatically enabled. A side-effect is that the
"QE Options" menu no longer exists.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: Fix ap_poll_requests counter in lost requests error path.
[S390] zcrypt: Fix possible dead lock in AP bus module.
[S390] cio: Device status validity.
[S390] kprobes: Align probe address.
[S390] Fix TCP/UDP pseudo header checksum computation.
[S390] dasd: Work around gcc bug.
This patch implements set_mac_address for the sungem driver. This
allows changing the mac address of the interface, even when the
interface is up.
Signed-off-by: Ruben Vandeginste <snowbender@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: fix usb-serial/ftdi build warning
USB: fix usb-serial/generic build warning
USB: another entry for the quirk list
USB: remove duplicated device id in airprime driver
USB: omap_udc: workaround dma_free_coherent() bogosity
UHCI: Fix problem caused by lack of terminating QH
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Fix warning message in PCIE port driver
PCI: Stop unhiding the SMBus on Toshiba laptops
PCI: Fix up PCI power management doc
pci: set pci=bfsort for PowerEdge R900
Fix annoying build warning:
drivers/usb/serial/ftdi_sio.c:890: warning: enumeration value `FT232RL' not handled in switch
Also add logic to detect FT232R chips (version 6.00, usb 2.0 full speed),
so that case isn't completely useless. (NOTE: FT232RL and FT232RQ are
the same chip in different packages: L is SSOP, Q is QFN.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix annoying build warning when CONFIG_USB_SERIAL_GENERIC is undefined.
drivers/usb/serial/generic.c:24: warning: `generic_probe' declared `static' but never defined
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both airprime and option now want to handle vendor ID 0x1410,
device ID 0x1100. Airprime calls it 'ExpressCard34 Qualcomm 3G CDMA'.
Option calls it 'Novatel Merlin XS620/S640'. Patch attached to remove it
from airprime.
From: Jon K Hellan <jon.kare.hellan@uninett.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various fixes to omap_udc, noted with some recent testing:
- Cope with some SMP-induced braindamage in ARM's dma_{alloc,free}_coherent()
implementation: alloc() can be called with IRQs blocked, but since late
last year that's no longer true for free(). This resolves really NASTY
problems with logspamming via WARN_ON(), indicating N-page leaks.
- Be more correct in handling GET_STATUS request for RECIP_ENDPOINT ... the
previous code only handled RECIP_INTERFACE, this version should be correct
except for (sigh) bulk/interrupt endpoints.
- Provide a better name for the function reporting whether the board has
vbus sensing wired up.
GET_STATUS requests for endpoint status still acts strangely though, at least
given one flakey host doesn't always ack the first DATA packet, then the packet
that gets retransmitted doesn't have data!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as871) fixes a problem introduced by an earlier change.
It turns out that some systems really do need to have a terminating
skeleton QH present whenever FSBR is on. I don't know any way to tell
which systems do need it and which don't; the easiest answer is to
have it there always.
This fixes the NumLock-hang bug reported by Jiri Slaby.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCIE error output should conform to vendor_id:device_id.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was found that the Toshiba laptops with hidden Intel SMBus have SMM
code handling the thermal management which accesses the SMBus. Thus it
is not safe to unhide it and let Linux access it. We have to leave the
SMBus hidden. SMM is a pain, really.
This fixes bugs #6315 and #6395, for good this time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[ bart: the ressurection of 2 years old patch which slipped thru the cracks
(thanks to Sergei Shtylyov for finding it) ]
These is the patch to turn on pdc202xx_new for ATAPI DMA. When testing, it
works fine without the (request_bufflen % 256) workaround as needed in libata.
ide-scsi filters out (pc->request_transfer % 1024) and use PIO, so the pdc202xx
ATAPI DMA problem is avoid. Both ide-cd and ide-scsi won't hit the ATAPI DMA
problem on pdc202xx_new.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since especially Serial ATA has it's own menu point now, I guess we can
change the description of the deprecated SATA driver as well, since the
new libATA subsystem is not configured through a SCSI low-level driver
anymore, but has it's own menu point.
From: Patrick Ringl <patrick_@freenet.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since hwif->ide_dma_check and hwif->ide_dma_on never queue any commands
(ide_config_drive_speed() sets transfer mode using polling and has no error
recovery) we are safe with setting hwgroup->busy for the time while DMA
setting for a drive is changed (so it won't race against I/O commands in fly).
I audited briefly all ->ide_dma_check/->ide_dma_on/->tuneproc/->speedproc
implementations and they all look OK wrt to this change.
This patch finally allowed me to close kernel bugzilla bug #8169
(once again thanks to Patrick Horn for reporting the issue & testing patches).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
"ide: fix drive side 80c cable check, take 2" patch from Tejun Heo (commit
fab59375b9) fixed 80c bit test (bit13 of word93)
but we also need to fix master/slave IDENTIFY order (slave device should be
probed first in order to make it release PDIAG- signal) and we should also
check for pre-ATA3 slave devices (which may not release PDIAG- signal).
[ Unfortunately the fact that IDE driver doesn't reset devices itself helps
only a bit as it seems that some BIOS-es reset ATA devices after programming
the chipset, some BIOS-es can be set to not probe/configure selected devices,
there may be no BIOS in case of add-on cards etc. ]
Since we are quite late in the release cycle and the required changes will
affect a lot of systems just revert the fix for now.
[ Please also see libata commit f31f0cc2f0. ]
Thanks goes out to Fernando Mitio Yamada for reporting the problem
and patiently testing patches.
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In the unlikely event that an AP device lost requests, don't forget to
update the ap_poll_requests counter too. Same must happen in case an AP
device is removed while there are still outstanding requests.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
If a AP device is unconfigured __ap_poll_all() will call
device_unregister() in software interrupt context which can cause
dead locks. To fix this the device will be only marked as unconfigured
and the device_unregister() call will be done later by either
ap_scan_bus() or ap_queue_message() in process context.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Only accumulate device status field in irb if it is valid.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
gcc incorrectly removes initialization of register 0 in dasd diag
inline assembly. Use different register to work around this compiler
bug.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Tracing through the code, no current PMU sleep notifier can abort sleep.
Since no new PMU sleep notifiers should be added, this patch simplifies the
code and removes the ability to abort sleep.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On most tg3 chips, the memory enable bit in the PCI command register
gets cleared during chip reset and must be restored before accessing
PCI registers using memory cycles. The chip does not generate
interrupt during chip reset, but the irq handler can still be called
because of irq sharing or irqpoll. Reading a register in the irq
handler can cause a master abort in this scenario and may result in a
crash on some architectures.
Use the TG3_FLAG_CHIP_RESETTING flag to tell the irq handler to exit
without touching any registers. The checking of the flag is in the
"slow" path of the irq handler and will not affect normal performance.
The msi handler is not shared and therefore does not require checking
the flag.
Thanks to Bernhard Walle <bwalle@suse.de> for reporting the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flag to support multiple PCIX split completions was never used
because of hardware bugs. This will make room for a new flag.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
->neigh_destructor() is killed (not used), replaced with
->neigh_cleanup(), which is called when neighbor entry goes to dead
state. At this point everything is still valid: neigh->dev,
neigh->parms etc.
The device should guarantee that dead neighbor entries (neigh->dead !=
0) do not get private part initialized, otherwise nobody will cleanup
it.
I think this is enough for ipoib which is the only user of this thing.
Initialization private part of neighbor entries happens in ipib
start_xmit routine, which is not reached when device is down. But it
would be better to add explicit test for neigh->dead in any case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After dvb tuner refactoring, the pllbuff has been altered such that the pll
address is now stored in buf[0]. Instead of sending buf to set_pll_input,
we should send buf+1.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Ivan Andrewjeski <ivan@fiero-gt.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: fix oops on "modprobe -r ohci1394" after network class_device conversion
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
[netdrvr] ewrk3: correct card detection bug
cxgb3 - fix white spaces in drivers/net/Kconfig
myri10ge: update driver version to 1.3.0-1.226
myri10ge: fix management of >4kB allocated pages
myri10ge: update wcfifo and intr_coal_delay default values
myri10ge: Serverworks HT2100 provides aligned PCIe completion
mv643xx_eth: add mv643xx_eth_shutdown function
SAA9730: Fix large pile of warnings
Revert "ucc_geth: returns NETDEV_TX_BUSY when BD ring is full"
cxgb3 - T3B2 pcie config space
cxgb3 - Fix potential MAC hang
cxgb3 - Auto-load FW if mismatch detected
cxgb3 - fix ethtool cmd on multiple queues port
Fix return code in pci-skeleton.c
skge: use per-port phy locking
skge: mask irqs when device down
skge: deadlock on tx timeout
[PATCH] airo: Fix an error path memory leak
[PATCH] bcm43xx: MANUALWLAN fixes
This is the rivafb equivalent of 238576e12f.
It fixes rivafb having a default backlight brightness of 0 (no picture at
all) on a PBook 6,1.
Signed-off-by: Guido Guenther <agx@sigxcpu.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds device ids of two Fujitsu Siemens Tablet PCs to pnp_dev_table
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turned out that it is almost impossible to trust ACPI, BIOS & Co.
regarding the C states. This was the reason to switch the local apic
timer off in C2 state already. OTOH there are sane and well behaving
systems, which get punished by that decision.
Allow the user to confirm that the local apic timer is trustworthy in C2
state. This keeps the default behaviour on the safe side.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 25496caec1, which
broke bootup on at least Ingo's ThinkPad T60. Need to figure out
exactly what is wrong before we can re-do the logic.
Requested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The networking subsystem has been converted from class_device to device
but ieee1394 hasn't. This results in a 100% reproducible NULL pointer
dereference if the ohci1394 driver module is unloaded while the eth1394
module is still loaded.
http://lkml.org/lkml/2006/11/16/147http://lkml.org/lkml/2007/3/14/4
This is a regression in 2.6.21-rc1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Ismail Dönmez <ismail@pardus.org.tr>
Arwin Vosselman pointed out:
> The ewrk3-driver doesn't function with 2.6.16-kernels (used 2.6.16.41 for
> my tests). Cards will never be detected due to this bug.
>
> drivers/net/ewrks3.c:
> Line 417 reads:
>
> if (nicsr == (CSR_TXD | CSR_RXD))
>
> that should be:
>
> if (nicsr != (CSR_TXD | CSR_RXD))
>
> Comparison with the same line in v2.4 shows why:
>
> 2.4:
> if (nicsr == (CSR_TXD | CSR_RXD)){
>
> blah, blah
> ==========
> 2.6:
> if (nicsr == (CSR_TXD | CSR_RXD))
> return -ENXIO;
>
> blah, blah
> ==========
>
> blah,blah will not, but should, be executed in 2.6 with a card being present.
>
> The fix mentioned above solves this bug.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix management of allocated physical pages when the architecture
page size is not 4kB since the firmware cannot cross 4K boundary.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SAA9730 driver doesn't quite grok what the difference between an ioport
and memory mapped I/O is. It just happened to work on the one Linux
system the SAA9730 happens to spend it's misserable existence on.
drivers/net/saa9730.c: In function 'evm_saa9730_enable_lan_int':
drivers/net/saa9730.c:68: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:70: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:72: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_disable_lan_int':
drivers/net/saa9730.c:78: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:80: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_clear_lan_int':
drivers/net/saa9730.c:85: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_block_lan_int':
drivers/net/saa9730.c:91: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'evm_saa9730_unblock_lan_int':
drivers/net/saa9730.c:97: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'show_saa9730_regs':
drivers/net/saa9730.c:150: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_allocate_buffers':
drivers/net/saa9730.c:292: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:295: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:302: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:305: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:312: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_cam_load':
drivers/net/saa9730.c:329: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:332: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_mii_init':
drivers/net/saa9730.c:369: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:395: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:403: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:410: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:432: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_control_init':
drivers/net/saa9730.c:470: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:474: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:478: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:484: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:487: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:490: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:493: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_stop':
drivers/net/saa9730.c:505: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:508: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:510: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_dma_init':
drivers/net/saa9730.c:536: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_start':
drivers/net/saa9730.c:556: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:560: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:564: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:567: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_tx':
drivers/net/saa9730.c:590: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_rx':
drivers/net/saa9730.c:664: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:729: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_write':
drivers/net/saa9730.c:848: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c: In function 'lan_saa9730_set_multicast':
drivers/net/saa9730.c:943: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
drivers/net/saa9730.c:949: warning: passing argument 2 of 'outl' makes integer from pointer without a cast
Fixed by using writel instead of outl. 42 warnings less.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This reverts commit 18babd3854.
Michael Barkowski points out that it's wrong, and I agree. The
patch causes a problem rather than fixes one after another
patch "ucc_geth: Fix BD processing" was applied. Before that
patch, current packet should be blocked. However after the patch
current packet is ok and we only need to block next.
Reported-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Under rare conditions, the MAC might hang while generating a pause frame.
This patch fine tunes the MAC settings to avoid the issue, allows for
periodic MAC state check, and triggers a recovery if hung.
Also fix one MAC statistics counter for the rev board T3B2.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver attempts to upgrade the FW if the card has the wrong version.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We assign the return value of register_netdev to i, but return rc later
on. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rather than a workqueue and a per-board mutex to control PHY,
use a tasklet and spinlock. Tasklet is lower overhead and works
just as well for this.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Wheen a port on the skge driver is not used, it should
mask off interrupts from theat port.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver will deadlock if gets a transmit timeout
because the netif_tx_lock() is already held.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: IA64: fix %ll build warnings
ACPI: IA64: fix allnoconfig build
ACPI: Only use IPI on known broken machines (AMD, Dothan/BaniasPentium M)
ACPI: ibm-acpi: allow module to load when acpi notifiers can't be set (v2)
ACPI: parse 2nd MADT by default
ACPICA: revert "acpi_serialize" changes
sony-laptop: MAINTAINERS fix entry, add L: and W:
ACPI: resolve HP nx6125 S3 immediate wakeup regression
ACPI: Add support to parse 2nd MADT
NULL checks should be before the first dereference.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/ds1374: Check workqueue creation status
i2c-i801: Restore the device state before leaving
i2c-amd8111: Missed cleanup
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: nat: avoid rerouting packets if only XFRM policy key changed
[NETFILTER]: nf_conntrack_netlink: add missing dependency on NF_NAT
[NET]: fix up misplaced inlines.
[SCTP]: Correctly reset ssthresh when restarting association
[BRIDGE]: Fix fdb RCU race
[NET]: Fix fib_rules dump race
[XFRM]: ipsecv6 needs a space when printing audit record.
[X25] x25_forward_call(): fix NULL dereferences
[SCTP]: Reset some transport and association variables on restart
[SCTP]: Increment error counters on user requested HBs.
[SCTP]: Clean up stale data during association restart
[IrDA]: Calling ppp_unregister_channel() from process context
[IrDA]: irttp_dup spin_lock initialisation
[IrDA]: Delay needed when uploading firmware chunks
The packet length checks in ipoib are broken: we add 4 bytes (IPoIB
encapsulation header) when sending a packet, not 20 bytes (hardware
address length) to each packet. Therefore, if connected mode is
enabled so that the interface MTU is larger than the multicast MTU,
IPoIB may end up trying to send too-long multicast packets. For
example, multicast is broken if a message of size 2048 bytes is sent
on an interface with UD MTU 2048, because 2048 is bigger than the real
limit of 2044 but the code tests against the wrong limit of 2060.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=418>,
submitted by Scott Weitzenkamp <sweitzen@cisco.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The connected mode code added the possibility that an neigh struct
gets freed in the list_for_each_entry() loop in path_rec_completion(),
which causes a use-after-free. Fix this by changing to the _safe
variant of the list walking macro.
This was spotted by the Coverity checker (CID 1567).
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA scaling code must not depend on register_cpu_notifier() if
CONFIG_HOTPLUG_CPU is not set, so put all related code into #ifdefs.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's a race between ipoib_mcast_leave() and ipoib_mcast_join_finish()
where we can try to detach from a multicast group before we've
attached to it. Fix this by reordering the code in ipoib_mcast_leave
to free the multicast group first, which waits for the multicast
callback thread (which calls ipoib_mcast_join_finish()) to complete
before detaching from the group.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The sense of the time_after_eq() test in ipoib_cm_stale_task() is
reversed so that only non-stale connections are reaped. Fix this by
changing to time_before_eq().
Noticed by Pradeep Satyanarayana <pradeep@us.ibm.com>.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check if workqueue creation failed. Further usage of NULL pointed
workqueue is not good I guess ;)
Signed-off-by: Cyrill V. Gorcunov <gorcunov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Restore the original host configuration on driver unload and on
suspend. In particular this returns the SMBus master in I2C mode if it
was originally in I2C mode, which should help with suspend/resume if
the BIOS expects to find the SMBus master in I2C mode.
This fixes bug #6449 (for real this time.)
http://bugzilla.kernel.org/show_bug.cgi?id=6449
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Tommi Kyntola <tommi.kyntola@ray.fi>
With 42101001.sb firmwares, we need a 10 ms delay between firmware chunks
upload on irda-usb.
Patch from Nigel Williams <nigelw@elder-gods.net>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: new Novatel device ids for option driver
USB: berry_charge: correct dbg string for second magic command
usblp: quirk flag and device entry for Seiko Epson M129C printer
airprime: USB ID for Novatel EV620 mini PCI-E card
USB: necessary update for mos7720 driver
USB: RAZR v3i unusual_devs
USB: two more device ids for dm9601 usbnet driver
USB: fix usb-serial regression
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: fix possible race when unloading zcrypt driver modules
[S390] zcrypt: fix possible dead lock in AP bus module
[S390] Wire up sys_utimes.
[S390] reboot from and dump to SCSI under z/VM fails.
[S390] Wire up compat_sys_epoll_pwait.
[S390] strlcpy is smart enough
[S390] memory detection: fix off by one bug.
[S390] cio: qdio slsb setup
This moves all of the Novatel device ids to the option driver, where
they belong.
Thanks to Novatel for providing a list of all supported devices.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was testing the berry_charge module with my Blackberry 8700c and had
great success, thanks. Looking at the code for my own learning I noticed
the following cut and paste error... just a nit.
Signed-off-by: Ken L Johnson <ken@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as872) adds a device table entry and a new quirk flag to
the usblp driver for the Seiko Epson Receipt printer. This printer
returns Vendor-Specific values for bInterfaceClass and
bInterfaceSubClass, but the bInterfaceProtocol value is valid and it
works with usblp. The new quirks flag tells the driver to ignore the
Class and SubClass values in the interface descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an ID to recognise the Novatel EV620 wireless adapter.
http://www.novatelwireless.com/products/expedite/ev620.html
It looks like a mini PCI-Express adapter. The mPCIE connector includes USB
pins... the card shows up to the system as a USB device, and powers itself
from the PCI bus.
The card I have isn't activated yet, so I can't get a PPP session up yet, but
I have tested basic serial communication successfully in both 2.6.18 and
2.6.20 kernels, once the product ID was added. (the driver changed quite a
bit between the two revs.) In both drivers, it responds to AT commands and
such.
Signed-off-by: Mark Glines <mark@glines.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
these devices have a shared interrupt endpoint. For serialcore to pass
an interrupt endpoint to a subdriver, the subdriver must define and
_export_ a fitting callback. The mos7720 driver failed to do so. This led
invariably to an oops upon open. This patch fixes it. The driver is useless
without it. Please try to get this into 2.6.21 and the stable kernels that
have this driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an unusual_devs entry for the Motorola RAZR 3vi.
From: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch for the linux-usb-devel tree adds two more
product ids to the dm9601 driver. These ids were found on
rebadged dm9601 devices in the wild.
Signed-off-by: Jon Dowland <jon@alcopop.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reverts d9a7ecacac since it
breaks drivers that need to access the ->port[] array in shutdown
(most of them).
Signed-Off: Jim Radford <radford@blackbean.org>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As per compact flash specifications, the default
irq mode upon cf insertion is pulse mode. this patch fixes
the driver to cope with that.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_ixp4xx_cf dodged dont-clear-drvdata-in-LLD bombing run as it used
platform_set_drvdata() instead of dev_set_drvdata(). This causes OOPS
on devres host release. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Warning(linux-2621-rc3g7/drivers/ata/libata-core.c:842): No description found for parameter 'unknown'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Regions are requested twice during initialization causing the second
one to fail. This is regression introduced during iomap conversion.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Adaptec 1220SA (SIL3132) to devices claimed by sata_sil24
Patch generated against 2.6.20.2
Signed-off-by: Jamie Clark <jclark@metaparadigm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
->prereset() returns -ENOENT to tell libata that the port is empty and
reset sequencing should be stopped. This is not an error condition.
Update ata_eh_reset() such that it sets device classes to ATA_DEV_NONE
and return success in on -ENOENT. This makes spurious error message
go away.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move try_module_get() call into spin protected block to prevent zcrypt
driver module unload while submitting a request to driver.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
AP bus module uses bus_for_each_dev() in software interrupt context to
poll for completed requests which might cause dead locks. Solution: use
private AP device list for polling in software interrupt context.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure set_slsb problems are handled correctly in
qdio_do_qdio_fill_input() and qdio_do_qdio_fill_output.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
