Re-schedule napi after napi_complete() for tx, if it is necessay.
In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.
After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another rebranded Novatel E371. qmi_wwan should drive this device, while
cdc_ether should ignore it. Even though the USB descriptors are plain
CDC-ETHER that USB interface is a QMI interface. Ref commit 7fdb7846c9
("qmi_wwan/cdc_ether: add device IDs for Dell 5804 (Novatel E371) WWAN
card")
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Runtime suspend shouldn't be executed if the tx queue is not empty,
because the device is not idle.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_post_reset() should sumbit rx urb and interrupt transfer,
otherwise the rx wouldn't work and the linking change couldn't be
detected.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/usb/cdc_ether.c:469:6: warning:
symbol 'usbnet_cdc_zte_status' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the hw rx checksum is always enabled, and the user couldn't switch
it to sw rx checksum.
Note that the RTL_VER_01 only support sw rx checksum only. Besides,
the hw rx checksum for RTL_VER_02 is disabled after
commit b9a321b48a ("r8152: Fix broken RX checksums."). Re-enable it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.
If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add LAN7801 MAC only support with phy fixup functions.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.
This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function lan78xx_probe(), variable ret takes the errno code on
failures. However, when the call to usb_alloc_urb() fails, its value
will keeps 0. 0 indicates success in the context, which is inconsistent
with the execution result. This patch fixes the bug, assigning
"-ENOMEM" to ret when usb_alloc_urb() returns a NULL pointer.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188771
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PID 0x1040 of Telit LE922A.
The qmi adapter requires to have DTR set for proper working,
so QMI_WWAN_QUIRK_DTR has been enabled.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduced a work-around in usbnet_cdc_status() for devices that exported
cdc carrier on twice on connect. Before the commit, this behavior caused
the link state to be incorrect. It was assumed that all CDC Ethernet
devices would either export this behavior, or send one off and then one on
notification (which seems to be the default behavior).
Unfortunately, it turns out multiple devices sends a connection
notification multiple times per second (via an interrupt), even when
connection state does not change. This has been observed with several
different USB LAN dongles (at least), for example 13b1:0041 (Linksys).
After bfe9b9d2df, the link state has been set as down and then up for
each notification. This has caused a flood of Netlink NEWLINK messages and
syslog to be flooded with messages similar to:
cdc_ether 2-1:2.0 eth1: kevent 12 may have been dropped
This commit fixes the behavior by reverting usbnet_cdc_status() to how it
was before bfe9b9d2df. The work-around has been moved to a separate
status-function which is only called when a known, affect device is
detected.
v1->v2:
* Do not open-code netif_carrier_ok() (thanks Henning Schild).
* Call netif_carrier_off() instead of usb_link_change(). This prevents
calling schedule_work() twice without giving the work queue a chance to be
processed (thanks Bjørn Mork).
Fixes: bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change fixes AX88772_suspend() USB vendor commands failure issues.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Allan Chou <allan@asix.com.tw>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate mdix code to phy driver to be called at config_init().
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If usb_submit_urb() called from the open function fails, the following
crash may be observed.
r8152 8-1:1.0 eth0: intr_urb submit failed: -19
...
r8152 8-1:1.0 eth0: v1.08.3
Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b6b7b
pgd = ffffffc0e7305000
[6b6b6b6b6b6b6b7b] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
...
PC is at notifier_chain_register+0x2c/0x58
LR is at blocking_notifier_chain_register+0x54/0x70
...
Call trace:
[<ffffffc0002407f8>] notifier_chain_register+0x2c/0x58
[<ffffffc000240bdc>] blocking_notifier_chain_register+0x54/0x70
[<ffffffc00026991c>] register_pm_notifier+0x24/0x2c
[<ffffffbffc183200>] rtl8152_open+0x3dc/0x3f8 [r8152]
[<ffffffc000808000>] __dev_open+0xac/0x104
[<ffffffc0008082f8>] __dev_change_flags+0xb0/0x148
[<ffffffc0008083c4>] dev_change_flags+0x34/0x70
[<ffffffc000818344>] do_setlink+0x2c8/0x888
[<ffffffc0008199d4>] rtnl_newlink+0x328/0x644
[<ffffffc000819e98>] rtnetlink_rcv_msg+0x1a8/0x1d4
[<ffffffc0008373c8>] netlink_rcv_skb+0x68/0xd0
[<ffffffc000817990>] rtnetlink_rcv+0x2c/0x3c
[<ffffffc000836d1c>] netlink_unicast+0x16c/0x234
[<ffffffc00083720c>] netlink_sendmsg+0x340/0x364
[<ffffffc0007e85d0>] sock_sendmsg+0x48/0x60
[<ffffffc0007e9c30>] SyS_sendto+0xe0/0x120
[<ffffffc0007e9cb0>] SyS_send+0x40/0x4c
[<ffffffc000203e34>] el0_svc_naked+0x24/0x28
Clean up error handling to avoid registering the notifier if the open
function is going to fail.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Cypress GX3 SuperSpeed to Gigabit Ethernet
Bridge Controller (Vendor=04b4 ProdID=3610).
Patch verified on x64 linux kernel 4.7.4, 4.8.6, 4.9-rc4 systems
with the Kensington SD4600P USB-C Universal Dock with Power,
which uses the Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge
Controller.
A similar patch was signed-off and tested-by Allan Chou
<allan@asix.com.tw> on 2015-12-01.
Allan verified his similar patch on x86 Linux kernel 4.1.6 system
with Cypress GX3 SuperSpeed to Gigabit Ethernet Bridge Controller.
Tested-by: Allan Chou <allan@asix.com.tw>
Tested-by: Chris Roth <chris.roth@usask.ca>
Tested-by: Artjom Simon <artjom.simon@gmail.com>
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Chris Roth <chris.roth@usask.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
To utilize phylib with interrupt fully than handling some of phy stuff in the MAC driver,
create irq_domain for USB interrupt EP of phy interrupt and
pass the irq number to phy_connect_direct() instead of PHY_IGNORE_INTERRUPT.
Idea comes from drivers/gpio/gpio-dl2.c
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 driver has been broken since (approx) 3.16.xx
when support was added for hardware RX checksums
on newer chip versions. Symptoms include random
segfaults and silent data corruption over NFS.
The hardware checksum logig does not work on the VER_02
dongles I have here when used with a slow embedded system CPU.
Google reveals others reporting similar issues on Raspberry Pi.
So, disable hardware RX checksum support for VER_02, and fix
an obvious coding error for IPV6 checksums in the same function.
Because this bug results in silent data corruption,
it is a good candidate for back-porting to -stable >= 3.16.xx.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The kalmia_send_init_packet() returns zero or a negative return
code, but gcc has no way of knowing that there cannot be a
positive return code, so it determines that copying the ethernet
address at the end of kalmia_bind() will access uninitialized
data:
drivers/net/usb/kalmia.c: In function ‘kalmia_bind’:
arch/x86/include/asm/string_32.h:78:22: error: ‘*((void *)ðernet_addr+4)’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
*((short *)to + 2) = *((short *)from + 2);
^
drivers/net/usb/kalmia.c:138:5: note: ‘*((void *)ðernet_addr+4)’ was declared here
This warning is harmless, but for consistency, we should make
the check for the return code match what the driver does everywhere
else and just progate it, which then gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet:
- Remove stale new_mtu <= 0 check in usbnet.c
- Set min_mtu = 0, max_mtu = 65535 (sub-drivers must set their own
max_mtu and/or min_mtu as needed)
r8152:
- Set appropriate max_mtu for different variants (1500 or 9194)
lan78xx:
- Set max_mtu = 9000
asix_driver:
- max_mtu = 16384 for ax88178 variant
ax88179:
- max_mtu = 4088
cdc_ncm:
- max_mtu from hardware
cdc-phonet:
- min_mtu = 6, max_mtu = 65541
sierra_net:
- max_mtu = 1500, call usbnet_change_mtu directly
- sierra_net_change_mtu checked for MTU > 1500, then called
usbnet_change_mtu, but if we set max_mtu to let the network core handle
the range check, then we can simply call usbnet_change_mtu directly
smsc75xx:
- max_mtu = 9000
CC: netdev@vger.kernel.org
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
CC: Hayes Wang <hayeswang@realtek.com>
CC: Oliver Neukum <oneukum@suse.com>
CC: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following four products of Lenovo and sort the order of the list.
VID PID
0x17ef 0x3062
0x17ef 0x3069
0x17ef 0x720c
0x17ef 0x7214
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check answers from USB stack and avoid re-sending the request
multiple times if the device does not respond.
This fixes the following problem, observed with a probably flaky adapter.
[62108.732707] usb 1-3: new high-speed USB device number 5 using xhci_hcd
[62108.914421] usb 1-3: New USB device found, idVendor=0b95, idProduct=7720
[62108.914463] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[62108.914476] usb 1-3: Product: AX88x72A
[62108.914486] usb 1-3: Manufacturer: ASIX Elec. Corp.
[62108.914495] usb 1-3: SerialNumber: 000001
[62114.109109] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
[62114.109139] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to send software reset: ffffff92
[62119.109048] asix 1-3:1.0 (unnamed net_device) (uninitialized):
Failed to write reg index 0x0000: -110
...
Since the USB timeout is 5 seconds, and the operation is retried 30 times,
this results in
[62278.180353] INFO: task mtpd:1725 blocked for more than 120 seconds.
[62278.180373] Tainted: G W 3.18.0-13298-g94ace9e #1
[62278.180383] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
...
[62278.180957] kworker/2:0 D 0000000000000000 0 5744 2 0x00000000
[62278.180978] Workqueue: usb_hub_wq hub_event
[62278.181029] ffff880177f833b8 0000000000000046 ffff88017fd00000 ffff88017b126d80
[62278.181048] ffff880177f83fd8 ffff880065a71b60 0000000000013340 ffff880065a71b60
[62278.181065] 0000000000000286 0000000103b1c199 0000000000001388 0000000000000002
[62278.181081] Call Trace:
[62278.181092] [<ffffffff8e0971fd>] ? console_conditional_schedule+0x2c/0x2c
[62278.181105] [<ffffffff8e094f7b>] schedule+0x69/0x6b
[62278.181117] [<ffffffff8e0972e0>] schedule_timeout+0xe3/0x11d
[62278.181133] [<ffffffff8daadb1b>] ? trace_timer_start+0x51/0x51
[62278.181146] [<ffffffff8e095a05>] do_wait_for_common+0x12f/0x16c
[62278.181162] [<ffffffff8da856a7>] ? wake_up_process+0x39/0x39
[62278.181174] [<ffffffff8e095aee>] wait_for_common+0x52/0x6d
[62278.181187] [<ffffffff8e095b3b>] wait_for_completion_timeout+0x13/0x15
[62278.181201] [<ffffffff8de676ce>] usb_start_wait_urb+0x93/0xf1
[62278.181214] [<ffffffff8de6780d>] usb_control_msg+0xe1/0x11d
[62278.181230] [<ffffffffc037d629>] usbnet_write_cmd+0x9c/0xc6 [usbnet]
[62278.181286] [<ffffffffc03af793>] asix_write_cmd+0x4e/0x7e [asix]
[62278.181300] [<ffffffffc03afb41>] asix_set_sw_mii+0x25/0x4e [asix]
[62278.181314] [<ffffffffc03b001d>] asix_mdio_read+0x51/0x109 [asix]
...
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quectel EC21 and EC25 need the same "set DTR" request as devices
based on the MDM9230 chipset, but has no USB3 support. Our best guess
is that the "set DTR" functionality depends on chipset and/or
baseband firmware generation. But USB3 is still an optional feature.
Since we cannot enable this unconditionally for all older devices, and
there doesn't appear to be anything we can use in the USB descriptors
to identify these chips, we are forced to use a device specific quirk
flag.
Reported-and-tested-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable ALDPS and EEE to avoid the possible failure when setting the PHY.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY relative settings together to hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move enabling PHY to init(), otherwise some other settings may fail.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the following functions forward.
r8152_mmd_indirect()
r8152_mmd_read()
r8152_mmd_write()
r8152_eee_en()
r8152b_enable_eee()
r8153_eee_en()
r8153_enable_eee()
r8152b_enable_fc()
r8153_aldps_en()
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOme statements in the driver only served to inform
which functions were entered. Ftrace can do that just as good without
needing memory. Remove the statements.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a few warnings when building kernel with W=1:
drivers/net/usb/lan78xx.c:1182:6: warning: no previous prototype for 'lan78xx_defer_kevent' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:1409:5: warning: no previous prototype for 'lan78xx_nway_reset' [-Wmissing-prototypes]
drivers/net/usb/lan78xx.c:2000:5: warning: no previous prototype for 'lan78xx_set_mac_addr' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more common logging style
Miscellanea:
o Add pr_fmt to prefix each output message
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macros that end in an underscore are just odd.
Add hso_dbg(level, fmt, ...) and use it everwhere instead.
Several uses had additional unnecessary newlines as the
macro added a newline. Remove the newline from the macro
and add newlines to each use as appropriate.
Remove now unused D<digit> macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue "pegasus_workqueue" queues a single work item per pegasus
instance and hence it doesn't require execution ordering. Hence,
alloc_workqueue has been used to replace the deprecated
create_singlethread_workqueue instance.
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure since it's a network driver.
Since there are fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check the coding style with checkpatch.pl and fix the warnings and errors.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Grant Grundler <grundler@chromium.org>
The miii_nway_restart() causes a PHY link change activity and
ax88772_link_reset will be called. link_reset will set
AX_CMD_WRITE_MEDIUM_MODE register correctly.
The asix_write_medium_mode in reset() fills in a default value to the register
which may be different from the negotiation result. So do this first.
Ignore the ret value since it's ignored in XXX_link_reset() functions.
Signed-off-by: Grant Grundler <grundler@google.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Grant Grundler <grundler@chromium.org>
https://lkml.org/lkml/2014/11/11/947
Ben Hutchings is correct. IEEE 802.3 spec section "22.2.4.1.1 Reset" requires
up to 500ms delay. Mitigate the "max" delay by polling the phy until BCM_RESET
bit is clear.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Allan Chou <allan@asix.com.tw>
The change fixes AX88772x resume failure by
- Restore incorrect AX88772A PHY registers when resetting
- Need to stop MAC operation when suspending
- Need to restart MII when restoring PHY
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Vincent Palatin <vpalatin@chromium.org>
Check the answers from the USB stack and avoid re-sending multiple times
the request if the device has disappeared.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Freddy Xin <freddy@asix.com.tw>
In order to R/W registers in suspend/resume functions, in_pm flags are
added to some functions to determine whether the nopm version of usb
functions is called.
Save BMCR and ANAR PHY registers in suspend function and restore them
in resume function.
Reset HW in resume function to ensure the PHY works correctly.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the oops discovered by the Umap2 project and Alan Stern.
The intf member needs to be set before the firmware is downloaded.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
The firmware in several ZTE devices (at least the MF823/831/910
modems/mifis) use OS fingerprinting to determine which type of device to
export. In addition, these devices export a REST API which can be used to
control the type of device. So far, on Linux, the devices have been seen as
RNDIS or CDC Ether.
When CDC Ether is used, devices of the same type are, as with RNDIS,
exported with the same, bogus random MAC address. In addition, the devices
(at least on all firmware revisions I have found) use the bogus MAC when
sending traffic routed from external networks. And as a final feature, the
devices sometimes export the link state incorrectly. There are also
references online to several other ZTE devices displaying this behavior,
with several different PIDs and MAC addresses.
This patch tries to improve the handling of ZTE devices by doing the
following:
* Create a new driver_info-struct that is used by ZTE devices that do not
have an explicit entry in the product table. This struct is the same as the
default cdc_ether driver info, but a new bind- and an rx_fixup-function
have been added.
* In the new bind function, we check if we have read a random MAC from the
device. If we have, then we generate a new random MAC address. This will
ensure that all devices get a unique MAC.
* The rx_fixup-function replaces the destination MAC address in the skb
with that of the device. I have not seen a revision of these devices that
behaves correctly (i.e., sets the right destination MAC), so I chose not to
do any comparison with for example the known, bogus addresses.
* The MF823/MF832/MF910 sometimes export cdc carrier on twice on connect
(the correct behavior is off then on). Work around this by manually setting
carrier to off if an on-notification is received and the NOCARRIER-bit is
not set.
This change will affect all devices, but it should take care of similar
mistakes made by other manufacturers. I tried to think of/look/test for
problems/regressions that could be introduced by this behavior, but could
not find any. However, my familiarity with this code path is not that
great, so there could be something I have overlooked.
I have tested this patch with multiple revisions of all three devices, and
they behave as expected. In other words, they all got a valid, random MAC,
the correct operational state and I can receive/sent traffic without
problems. I also tested with some other cdc_ether devices I have and did
not find any problems/regressions caused by the two general changes.
v3->v4:
* Forgot to remove unused variables, sorry about that (thanks David
Miller).
v2->v3:
* I had forgot to remove the random MAC generation from usbnet_cdc_bind()
(thanks Oliver).
* Rework logic in the ZTE bind-function a bit.
v1->v2:
* Only generate random MAC for ZTE devices (thanks Oliver Neukum).
* Set random MAC and do RX fixup for all ZTE devices that do not have a
product-entry, as the bogus MAC have been seen on devices with several
different PIDs/MAC addresses. In other words, it seems to be the default
behavior of ZTE CDC Ether devices (thanks Lars Melin).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big USB driver update for 4.8-rc1. Lots of the normal stuff
in here, musb, gadget, xhci, and other updates and fixes. All of the
details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAleVPioPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspB5AAnj7a
VJ2t2kcWzFUNQ6dyJrJCGGRAAKDZmb5CnOGeqJmdVpDzN1CGLYjfiw==
=47iA
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB driver update for 4.8-rc1. Lots of the normal
stuff in here, musb, gadget, xhci, and other updates and fixes. All
of the details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
cdc-acm: beautify probe()
cdc-wdm: use the common CDC parser
cdc-acm: cleanup error handling
cdc-acm: use the common parser
usbnet: move the CDC parser into USB core
usb: musb: sunxi: Simplify dr_mode handling
usb: musb: sunxi: make unexported symbols static
usb: musb: cppi41: add dma channel tracepoints
usb: musb: cppi41: move struct cppi41_dma_channel to header
usb: musb: cleanup cppi_dma header
usb: musb: gadget: add usb-request tracepoints
usb: musb: host: add urb tracepoints
usb: musb: add tracepoints to dump interrupt events
usb: musb: add tracepoints for register access
usb: musb: dsps: use musb register read/write wrappers instead
usb: musb: switch dev_dbg to tracepoints
usb: musb: add tracepoints support for debugging
usb: quirks: Add no-lpm quirk for Elan
phy: rcar-gen3-usb2: fix mutex_lock calling in interrupt
phy: rockhip-usb: use devm_add_action_or_reset()
...
The dependencies were impossible to handle preventing
drivers for CDC devices not which are not network drivers
from using the common parser.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices of the same type all export the same, random MAC address. This
behavior has been seen on the ZTE MF910, MF823 and MF831, and there are
probably more devices out there. Fix this by generating a valid random MAC
address if we read a random MAC from device.
Also, changed the memcpy() to ether_addr_copy(), as pointed out by
checkpatch.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -i provides a driver version that is hard coded.
Export the same value via "modinfo".
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8153-AD supports a persistent system specific MAC address.
This means a device plugged into two different systems with host side
support will show different (but persistent) MAC addresses.
This information for the system's persistent MAC address is burned in when
the system HW is built and available under \_SB.AMAC in the DSDT at runtime.
This technology is currently implemented in the Dell TB15 and WD15 Type-C
docks. More information is available here:
http://www.dell.com/support/article/us/en/04/SLN301147
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no conflict between the work_queue function and
rtl8152_set_speed(), so we don't have to cancel the delayed work in
rtl8152_set_speed().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90186af404 ("r8152: fix lockup when runtime PM is enabled"),
the autoresume wouldn't start the device before rtl8152_open() is finished.
Therefore, we don't have to reset the linking status before and after
autoresume. That is, one of netif_carrier_off() in rtl8152_open() could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtl_hw_phy_work_func_t(), the flag of PHY_RESET is set in
rtl_ops.hw_phy_cfg() and cleared in rtl8152_set_speed(). Therefore,
the rtl_phy_reset() is never run and is unnecessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN_WAKE_EN is not used to determine if the device could support
WOL. It is used to signal a GPIO pin when a WOL event occurs. The WOL
still works even though it is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8152 doesn't have U1U2 and U2P3 features, so use different
runtime functions for RTL812 and RTL8153 by adding autosuspend_en()
to rtl_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several Lenovo users have reported problems with their Sierra
Wireless EM7455 modem. The driver has loaded successfully and
the MBIM management channel has appeared to work, including
establishing a connection to the mobile network. But no frames
have been received over the data interface.
The problem affects all EM7455 and MC7455, and is assumed to
affect other modems based on the same Qualcomm chipset and
baseband firmware.
Testing narrowed the problem down to what seems to be a
firmware timing bug during initialization. Adding a short sleep
while probing is sufficient to make the problem disappear.
Experiments have shown that 1-2 ms is too little to have any
effect, while 10-20 ms is enough to reliably succeed.
Reported-by: Stefan Armbruster <ml001@armbruster-it.de>
Reported-by: Ralph Plawetzki <ralph@purejava.org>
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Reported-by: Rasmus Lerdorf <rasmus@lerdorf.com>
Reported-by: Samo Ratnik <samo.ratnik@gmail.com>
Reported-and-tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
LINK_OFF_WAKE_EN should be cleared after autoresume, otherwise after
system suspend, the system would wake up when linking off occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When MTU is changed unlink_urbs() flushes RX Q but mean while usbnet_bh()
can fill up the Q at the same time.
Depends on which HCD is down there unlink takes long time then the flush
never ends.
Signed-off-by: Soohoon Lee <soohoon.lee@f5.com>
Reviewed-by: Kimball Murray <kmurray@f5.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
In set_speed(), BMCR_RESET would be set when the flag of PHY_RESET
is set. Use BMCR_RESET to replace testing the flag of PHY_RESET.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx early size should be
(agg_buf_sz - packet size) / 8
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset the BMU to clear the rx/tx fifo. This avoids that the unexpected
data remains in the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable MAC clock speed down. It may casue the first control
transfer to contain the wrong data, when the power state change
from U1 to U0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user may change the speed. Use it to replace the default one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calling set_speed() from open() to rtl_hw_phy_work_func_t().
Then, we would set the default speed only for first initialization
or after resuming.
Besides, the set_speed() could handle the flag of PHY_RESET which
would be set in rtl_ops.hw_phy_cfg().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the settings of PHY to a work queue and schedule it after
rtl_ops.init().
There are some reasons for this. First, the settings are only
needed for the first time initialization or after the power
down occurs.
Second, the settings are independent with the others.
Last, the settings may take more time than the others. Leave
they in probe() or open() may delay the following flows.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace netdev_alloc_skb_ip_align() with napi_alloc_skb() which can save
several CPU cycles by avoiding having to disable and re-enable IRQs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To detect link status up/down for connections where autonegotiation is
explicitly disabled, we don't get an irq but need to poll the status
register for link up/down detection.
This patch adds a workqueue to poll for link status.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If !count is true, count < 4 is also true.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation updates the mtu size and notify cdc_ncm
device using USB_CDC_SET_MAX_DATAGRAM_SIZE request about datagram
size change instead of changing rx_urb_size.
Whenever mtu is being changed, datagram size should also be
updated. Also updating maxmtu formula so it takes max_datagram_size with
use of cdc_ncm_max_dgram_size() and not ctx.
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
