* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a couple drivers that do not correctly terminate their pci_device_id
lists. This results in garbage being spewed into modules.pcimap when the
module happens to not have 28 NULL bytes following the table, and/or the
last PCI ID is actually truncated from the table when calculating the
modules.alias PCI aliases, cause those unfortunate device IDs to not
auto-load.
Signed-off-by: Kees Cook <kees@ubuntu.com>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_property has been renamed to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is only called at init time and only happens if the BIOS screws
something up, so the leak is slight and it is probably not worth sending to
2.6.22.x. The driver would not initialize the interface in the case, and I
have no reports of this happening. I have booted and run tests on a system
with this patch. Note that the original patch was munged by the mailer,
here's a new one.
If we ever hit the "default:" case in the switch in try_init_dmi(),
then we'll leak the storage allocated with kzalloc() and assigned
to 'info'.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When trying to load the ipmi_si module on a powerpc with no BMC (baseboard
management controller) the driver failes to load correctly, but doesn't
unregister itself from of_platform. So, on a second modprobe the kernel
crashes. This patch adds the missing unregister call.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a rather obvious error that Patrick found in the setup routines. Need to
set the proper address space in the ACPI case.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add pci_remove handling to the driver, so it will clean up if
the device is hot-removed.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IPMI driver used enable_irq and disable_irq when it got into situations
where it couldn't allocate memory; it did this to avoid having the interrupt
just lock the machine when it couldn't get memory to perform the transaction
to disable the interrupt.
This patch modifies the driver to not use disable_irq and enable_irq. It
instead sends the messages to the BMC to perform this operation. It also
makes sure interrupts are cleanly disabled when the interface is shut down and
cleans up some shutdown things that are no longer necessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for of_platform_driver to the ipmi_si module. When loading the
module, the driver will be registered to of_platform. The driver will be
probed for all devices with the type ipmi. It's supporting devices with
compatible settings ipmi-kcs, ipmi-smic and ipmi-bt. Only ipmi-kcs could be
tested.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Heiko J Schick <schihei@de.ibm.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipmi_si_intf tries to access default ports, if no device could be found
elsewhere. On PPC we have a function to check, if these legacy IO ports
are accessible. This patch adds a check for these ports on PPC. This
patch fixes a breakage of IPMI module on PPC machines without a BMC.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix various problems pointed out by Andrew Morton and others:
* platform_device_unregister checks for NULL, no need to check here.
* Formatting fixes.
* Remove big macro and convert to a function.
* Use strcmp instead of defining a broken case-insensitive comparison,
and make the output parameter info match the case of the input one
(change "I/O" to "i/o").
* Return the length instead of 0 from the hotmod parameter handler.
* Remove some unused cruft.
* The trydefaults parameter only has to do with scanning the "standard"
addresses, don't check for that on ACPI.
Signed-off-by: Corey Minyard <cminyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove all =0 and =NULL from static initializers. They are not needed and
removing them saves space in the object files.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IPMI BT subdriver has been patched to survive "long busy" timeouts seen
during firmware upgrades and resets. The patch never returns the HOSED state,
synthesizes response messages with meaningful completion codes, and recovers
gracefully when the hardware finishes the long busy. The subdriver now issues
a "Get BT Capabilities" command and properly uses those results. More
informative completion codes are returned on error from transaction starts;
this logic was propogated to the KCS and SMIC subdrivers. Finally, indent and
other style quirks were normalized.
Signed-off-by: Rocky Craig <rocky.craig@hp.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change pci_module_init() to the new interface, and check the return code to
avoid warnings and give the user useful information if this fails.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the ability to hot add and remove interfaces in the ipmi_si driver. Any
users who have the device open will get errors if they try to send a message.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure to delay a little in the IPMI poll routine so we can pass in a
timeout time and thus time things out.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the IPMI message handler requested that the interface look for events,
the ipmi_si driver would request flags, see if the event buffer full flag was
set, then request events. It's better to just send the request for events, as
it cuts one message out of the transaction if there happens to be events, and
it will fetch events even if the event buffer was not full.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some commands and operations on a BMC can cause the BMC to "go away" for a
while. This can cause the automatic flag processing and other things of that
nature to timeout and generate annoying logs, or possibly cause other bad
things to happen when in firmware update mode.
Add detection of those commands (cold reset, warm reset, and any firmware
command) and turns off automatic processing for 30 seconds. It also add a
manual override either way.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass in the sysfs name from the lower-level IPMI driver, as the coming IPMI
serial driver will need that to link properly from the serial device sysfs
directory.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=7439
It looks like device registration in drivers/char/ipmi/ipmi_si_intf.c was
cleaned up and a small error was made when setting the class_mask. The fix
is simple as the correct mask value is defined in the code but is not used.
Acked-by: Corey Minyard <minyard@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These returns should be negative, like the others in this function.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
After the previous patch to disable the kernel IPMI daemon if interrupts
were available, the issue of broken hardware was raised, and a reasonable
request to add an override was mode. So here it is.
Allow the user to force the kernel ipmi daemon on or off. This way,
hardware with broken interrupts or users that are not concerned with
performance can turn it on or off to their liking.
[akpm@osdl.org: save 4 bytes in vmlinux]
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
gcc issues the following warning:
drivers/char/ipmi/ipmi_si_intf.c: In function âinit_ipmi_siâ:
drivers/char/ipmi/ipmi_si_intf.c:1729: warning: âdata.irqâ may be used uninitialized in this function
This is indeed a bug. data.irq is completely uninitialized in some code
paths. Worse than that, data from a previous decode_dmi() run can easily
leak through successive calls.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the driver has interrupts available to it, there is really no reason to
have a kernel daemon push the IPMI state machine.
Note that I have experienced machines where the interrupts do not work
correctly. This was a long time ago and hopefully things are better now.
If some machines still have broken interrupts, a blacklist will need to be
added.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If one of the OEM flags becomes set in the flags from the hardware, the
driver could hang if no OEM handler was set. Fix the code to handle this.
This was tested by setting the flags by hand after they were fetched.
Signed-off-by: Corey Minyard <minyard@acm.org>
Ackde-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the ipmi_si module is loaded on a system without any ipmi device, it
fails with nodev. It would be fine if all resources were freed. A call to
device_unregister() is missing, resulting to a oops when you remove the
ipmi_msghandler.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was some old high-res-timer code in the IPMI driver that is dead.
Remove it.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corey Minyard <minyard@acm.org>
The kthread used to speed up polling for IPMI was using udelay in its
busy-wait polling loop when the lower-level state machine told it to do a
short delay. This just used CPU and didn't help scheduling, thus causing
bad problems with other tasks. Call schedule() instead.
Signed-off-by: Corey Minyard <minyard@acm.org>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Corey Minyard <minyard@acm.org>
This patch is pretty important to get in for IPMI, new systems have been
changing the way ACPI and IPMI interact, and this works around the problems
for now. This is a temporary fix until we get proper ACPI handling in
IPMI.
Fixed releasing already-allocated regions when a later request fails, and
forward-ported it to HEAD.
Some BIOSes reserve disjoint I/O regions in their ACPI tables for the IPMI
controller. This causes problems when trying to register the entire I/O
region. Therefore we must register each I/O port separately.
Signed-off-by: Jordan Hargrave <Jordan_Hargrave@dell.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
gcc complains about __devinit in the wrong location:
drivers/char/ipmi/ipmi_si_intf.c:2205: warning: '__section__' attribute does not apply to types
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the remaining semaphores to mutexes in the IPMI driver. The
watchdog was using a semaphore as a real semaphore (for IPC), so the
conversion there required adding a completion.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tidy up various coding standard things, mostly removing the space after !,
but also break some long lines and fix a few other spacing inconsistencies.
Also fixes some bad error reporting when deleting an IPMI user.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Matt Domsch noticed a startup race with the IPMI kernel thread, it was
possible (though extraordinarly unlikely) that a message could come in
before the upper layer was ready to handle it. This patch splits the
startup processing of an IPMI interface into two parts, one to get ready
and one to actually start the processes to receive messages from the
interface.
[akpm@osdl.org: cleanups]
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add full driver model support for the IPMI driver. It links in the proper
bus and device support.
It adds an "ipmi" driver interface that has each BMC discovered by the
driver (as a device). These BMCs appear in the devices/platform directory.
If there are multiple interfaces to the same BMC, the driver should
discover this and will only have one BMC entry. The BMC entry will have
pointers to each interface device that connects to it.
The device information (statistics and config information) has not yet been
ported over to the driver model from proc, that will come later.
This work was based on work by Yani Ioannou. I basically rewrote it using
that code as a guide, but he still deserves credit :).
[bunk@stusta.de: make ipmi_find_bmc_guid() static]
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify the PCI hanling code for the IPMI driver to use the new method of
tables and registering, and adds more generic PCI handling for IPMI.
Unfortunately, this required a rather large rework of the way the driver
did detection so it would be more event-driven.
[bunk@stusta.de: make a struct static]
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On mips:
drivers/char/ipmi/ipmi_si_intf.c:1274: error: conflicting types for 'mem_inb'
include/asm/io.h:436: error: previous definition of 'mem_inb' was here
Don't look at line 436 unless you really know what you're doing.
Move those static functions out of more or less generic namespace.
Signed-off-by: Alexey "## should be banned" Dobriyan <adobriyan@gmail.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At the 2.6.12 timeframe ipmi_si_intf.c was patched to provide default
register spacings in try_init_acpi() if the register spacing was set to
zero, similar to code in other routines.
Unfortunately, another patch was simultaneously added that exits early from
try_init_acpi() if the register spacings are set to zero, circumventing the
new defaults. This patch removes the early exit code and some incorrect
comments that aren't present in other common code snippets.
Signed-off-by: Rocky Craig <rocky.craig@hp.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Andi Kleen's x86_64 patch to use DMI, and my ia64 to use DMI, there is
now a new CONFIG_DMI option which takes the place of CONFIG_X86 to denote
the availability of the DMI functions. Make the IPMI driver use CONFIG_DMI
instead.
Tested on ia64 2.6.15 kernel plus the previous patch, on a Dell PowerEdge
7250 Itanium2 server, and it now autodetects the IPMI KCS driver as
expected.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While doing some testing I discovered that if the BIOS on a board does not
properly setup the DMI information it leads to a panic in the IPMI code.
The panic is due to dereferencing a pointer which is not initialized. The
pointer is initialized in port_setup() and/or mem_setup() and used in
init_one_smi() and cleanup_one_si(), however if either port_setup() or
mem_setup() return ENODEV the pointer does not get initialized.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On IPMI systems with BT interfaces, we don't start the kernel thread, so
smi_info->thread is NULL. Test for NULL when stopping the thread, because
kthread_stop() doesn't, and an oops ensues otherwise.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert ipmi driver thread to kthread API, only sleep when interface is
idle.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We must poll for responses to commands when interrupts aren't in use. The
default poll interval is based on using a kernel timer, which varies with HZ.
For character-based interfaces like KCS and SMIC though, that can be way too
slow (>15 minutes to flash a new firmware with KCS, >20 seconds to retrieve
the sensor list).
This creates a low-priority kernel thread to poll more often. If the state
machine is idle, so is the kernel thread. But if there's an active command,
it polls quite rapidly. This decrease a firmware flash time from 15 minutes
to 1.5 minutes, and the sensor list time to 4.5 seconds, on a Dell PowerEdge
x8x system.
The timer-based polling remains, to ensure some amount of responsiveness even
under high user process CPU load.
Checking for a stopped timer at rmmod now uses atomics and del_timer_sync() to
ensure safe stoppage.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
BMCs can get into ERROR0 state while flashing new firmware, particularly while
the BMC is erasing the next flash block, which may take a just under 2 seconds
on a Dell PowerEdge 2800 (1.75 seconds typical), during which time the
single-threaded firmware may not be able to process new commands. In
particular, clearing OBF may not take effect immediately.
We want it to delay in ERROR0 after clearing OBF a bit waiting for OBF to
actually be clear before proceeding.
This introduces a new return value from the LLDD's event loop,
SI_SM_CALL_WITH_TICK_DELAY. This means the calling thread/timer should
schedule_timeout() at least 1 tick, rather than busy-wait. This is a longer
delay than SI_SM_CALL_WITH_DELAY, which is typically a 250us busy-wait.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some commands, on some system BMCs, don't respond at at all. This is seen on
Dell PowerEdge x6xx and x7xx systems with IPMI 1.0 BT controllers when a "Get
SDR" command is issued, with a length field of 0x3A, which happens to be the
length of about SDR entries. If another length is passed, this command
succeeds.
This patch adds general infrastructure for receiving commands before they're
passed down to the low-level drivers, such that they can be completed
immediately, or modified, prior to being sent to ->start_transaction().
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make SMIC driver ignore EVT_AVAIL and SMS_ATN bits in flags register, as
they're used by systems management interrupts, not the host OS.
Make the OEM0 Data Available handler work for pre-IPMI 1.5 systems from Dell
too.
Without these two fixes, PowerEdge 2650 and other similar systems with SMIC
may hang a process (modprobe or anything using /dev/ipmi0).
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A number of small changes for the various system interface drivers,
consolidated from a number of patches from Matt Domsch.
Clear B2H_ATN and drain the BMC message buffer on command timeout. This
prevents further commands from failing after a timeout.
Add bt_debug and smic_debug module parameters, expose them in sysfs. This
lets you enable and disable debugging messages at runtime.
Unsigned jiffies math in ipmi_si_intf.c causes a too-large value to be passed
to ->event() after jiffies wrap-around. The BT driver had caught this, but
didn't know how to fix it. Now all calls to ->event() use a sane value for
time.
Increase timeout for commands handed to the BT driver from 2 seconds to 5
seconds. This is necessary particularly when the previous command was a
"Clear SEL", as that command completes, yet the BMC isn't really ready to
handle another command yet.
Silence BT debugging messages which were being printed on the console.
Increase SMIC timeout form 1/10s to 2s. This is needed on Dell PowerEdge 2650
and PowerEdge 750 with ERA/O cards to allow commands to complete without
timing out.
Adds kcs_debug module param, to match behavior of BT and SMIC. This also
prevents messages from being sent to the console unless explicitly requested.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up various style issues in the IPMI driver. Should be no functional
changes.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds MODULE_VERSION, MODULE_DESCRIPTION, and MODULE_AUTHOR tags to the
IPMI driver modules. Also changes the MODULE_VERSION to remove the
prepended 'v' on each value, consistent with the module versioning policy.
This patch also removes all the version information from everything except
the ipmi_msghandler module.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ipmi driver does not have a way to handle firmware-generated events
which have the OEM[012] Data Available flags set. In such a case, the
SMS_ATN bit may never get cleared by firmware, leaving the driver looping
infinitely but never able to make any progress.
This patch first simplifies storage and use of the data returned from an
IPMI Get Device ID command.
It then creates a new per-OEM handler hook, which should know how to handle
events with the OEM[012] Data Available flags set. It then uses this to
implement a workaround for IPMI 1.5-capable Dell PowerEdge servers which
are susceptable to setting the OEM[012] Data Available flags when the
driver can't handle it.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some problems with the high-res timer support.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
annotated, a bunch of direct dereferencing replaced with readb().
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable interrupts for a BT interface. There is a specific register that
needs to be set up to enable interrupts that also must be modified to clear
the irq.
Also, don't reset the BMC on a BT interface. That's probably not a good
idea as the BMC may be performing other important functions and a reset
should only be a last resort. Also, that register is also used to
enable/disable interrupts to the BT; modifying it may screw up the
interrupts.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the ACPI register bit width is zero (an invalid value) assume it is the
default spacing. This avoids some coredumps on invalid data and makes some
systems work that have broken ACPI data.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ignore the bottom bit of the base address from the DMI data. It is
supposed to be set to 1 if it is I/O space. Few systems do this, but this
enables the ones that do set it to work properly.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
