.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs. This allows
low-level device drivers to create files in
/sys/class/infiniband/<hca>/ports/<N>/
without having to poke through the internals of the RDMA sysfs handling.
There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We shouldn't free things here because we free them later.
The call tree looks like this:
iser_connect() ==> initiating the connection establishment
and later
iser_cma_handler() => iser_route_handler() => iser_create_ib_conn_res()
if we fail here, eventually iser_conn_release() is called, resulting
in a double free.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The iser connection teardown flow isn't over until the underlying
Connection Manager (e.g the IB CM) delivers a disconnected or timeout
event through the RDMA-CM. When the remote (target) side isn't
reachable, e.g when some HW e.g port/hca/switch isn't functioning or
taken down administratively, the CM timeout flow is used and the event
may be generated only after relatively long time -- on the order of
tens of seconds.
The current iser code exposes this possibly long delay to higher
layers, specifically to the iscsid daemon and iscsi kernel stack. As a
result, the iscsi stack doesn't respond well: this low-level CM delay
is added to the fail-over time under HA schemes such as the one
provided by DM multipath through the multipathd(8) service.
This patch enhances the reference counting scheme on iser's IB
connections so that the disconnect flow initiated by iscsid from user
space (ep_disconnect) doesn't wait for the CM to deliver the
disconnect/timeout event. (The connection teardown isn't done from
iser's view point until the event is delivered)
The iser ib (rdma) connection object is destroyed when its reference
count reaches zero. When this happens on the RDMA-CM callback
context, extra care is taken so that the RDMA-CM does the actual
destroying of the associated ID, since doing it in the callback is
prohibited.
The reference count of iser ib connection normally reaches three,
where the <ref, deref> relations are
1. conn <init, terminate>
2. conn <bind, stop/destroy>
3. cma id <create, disconnect/error/timeout callbacks>
With this patch, multipath fail-over time is about 30 seconds, while
without this patch, multipath fail-over time is about 130 seconds.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The iscsi connection object life cycle includes binding and unbinding
(conn_stop) to/from the iscsi transport connection object. Since
iscsi connection objects are recycled, at the time the transport
connection (e.g iser's IB connection) is released, it is not valid to
touch the iscsi connection tied to the transport back-pointer since it
may already point to a different transport connection.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add handler to handle events such as port up and down. This is useful
when testing high-availability schemes such as multi-pathing.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for masked atomic operations (masked compare and swap,
masked fetch and add).
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Randomize local port allocation in the way sctp_get_port_local() does.
Update rover at the end of loop since we're likely to pick a valid port
on the first try.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This allows the compiler to do a bit better; on my x86-64 build:
add/remove: 0/2 grow/shrink: 1/0 up/down: 2288/-2365 (-77)
function old new delta
nes_init_phy 273 2561 +2288
nes_init_1g_phy 469 - -469
nes_init_2025_phy 1896 - -1896
Signed-off-by: Roland Dreier <rolandd@cisco.com>
nes_{read,write}_1G_phy_reg() are using phy_lock while
nes_{read,write}_10G_phy_reg() leave that to the caller.
Remove phy_lock from 1G routines and leave the locking to the caller.
Add additional phy_lock calls around 1G read/write.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an RDMA/iWARP driver for Chelsio T4 Ethernet adapters.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The DMA API is preferred; no functional change.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The DMA API is preferred; no functional change.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The low level cxgb3 driver can return NET_XMIT_CN and friends.
The iw_cxgb3 driver should _not_ treat these as errors.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The DMA API is preferred; no functional change.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Several RDMA user-access drivers have file_operations structures with
no .llseek method set. None of the drivers actually do anything with
f_pos, so this means llseek is essentially a NOP, instead of returning
an error as leaving other file_operations methods unimplemented would
do. This is mostly harmless, except that a NULL .llseek means that
default_llseek() is used, and this function grabs the BKL, which we
would like to avoid.
Since llseek does nothing useful on these files, we would like it to
return an error to userspace instead of silently grabbing the BKL and
succeeding. For nearly all of the file types, we take the
belt-and-suspenders approach of setting the .llseek method to
no_llseek and also calling nonseekable_open(); the exception is the
uverbs_event files, which are created with anon_inode_getfile(), which
already sets f_mode the same way as nonseekable_open() would.
This work is motivated by Arnd Bergmann's bkl-removal tree.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check correct variable for allocation failure
RDMA/nes: Correct cap.max_inline_data assignment in nes_query_qp()
RDMA/cm: Set num_paths when manually assigning path records
IB/cm: Fix device_create() return value check
The intent here is to check the "mfrpl->mapped_page_list" allocation.
We checked "mfrpl->ibfrpl.page_list" earlier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cap.max_inline_data is incorrectly set in init_attr instead of attr.
Set it in attr so subsequent init_attr.cap assignment will get the
correct value.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When manually assigning the path records to use for a connection, save
the number of paths that were set. Otherwise, checks against num_path
will show 0, even though path record data is available.
This was discovered by manually setting the path records from user
space, then querying the kernel to see if the correct path records
were assigned, only to discover that the kernel returned 0 path
records to the query.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Finally this bit can be removed. Currently, after the bonding driver is
changed/fixed (32a806c194 net-next-2.6),
that's not possible for an addr with different length than dev->addr_len
to be present in list. Removing this check as in new mc_list there will be
no addrlen in the record.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: numa: fix BUILD_BUG_ON for node_read_distance
driver-core: document ERR_PTR() return values
kobject: documentation: Update to refer to kset-example.c.
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
kobject: documentation: Fix erroneous example in kobject doc.
driver-core: fix missing kernel-doc in firmware_class
Driver core: Early platform kernel-doc update
sysfs: fix sysfs lockdep warning in mlx4 code
sysfs: fix sysfs lockdep warning in infiniband code
sysfs: fix sysfs lockdep warning in ipmi code
sysfs: Initialised pci bus legacy_mem field before use
sysfs: use sysfs_bin_attr_init in firmware class driver
This fixes a sysfs lockdep warning in the infiniband code.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (69 commits)
[SCSI] scsi_transport_fc: Fix synchronization issue while deleting vport
[SCSI] bfa: Update the driver version to 2.1.2.1.
[SCSI] bfa: Remove unused header files and did some cleanup.
[SCSI] bfa: Handle SCSI IO underrun case.
[SCSI] bfa: FCS and include file changes.
[SCSI] bfa: Modified the portstats get/clear logic
[SCSI] bfa: Replace bfa_get_attr() with specific APIs
[SCSI] bfa: New portlog entries for events (FIP/FLOGI/FDISC/LOGO).
[SCSI] bfa: Rename pport to fcport in BFA FCS.
[SCSI] bfa: IOC fixes, check for IOC down condition.
[SCSI] bfa: In MSIX mode, ignore spurious RME interrupts when FCoE ports are in FW mismatch state.
[SCSI] bfa: Fix Command Queue (CPE) full condition check and ack CPE interrupt.
[SCSI] bfa: IOC recovery fix in fcmode.
[SCSI] bfa: AEN and byte alignment fixes.
[SCSI] bfa: Introduce a link notification state machine.
[SCSI] bfa: Added firmware save clear feature for BFA driver.
[SCSI] bfa: FCS authentication related changes.
[SCSI] bfa: PCI VPD, FIP and include file changes.
[SCSI] bfa: Fix to copy fpma MAC when requested by user space application.
[SCSI] bfa: RPORT state machine: direct attach mode fix.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix CX4 link problem in back-to-back configuration
RDMA/nes: Clear stall bit before destroying NIC QP
RDMA/nes: Set assume_aligned_header bit
RDMA/cxgb3: Wait at least one schedule cycle during device removal
IB/mad: Ignore iWARP devices on device removal
IPoIB: Include return code in trace message for ib_post_send() failures
IPoIB: Fix TX queue lockup with mixed UD/CM traffic
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
Commit 09124e19 ("RDMA/nes: Add support for KR device id 0x0110") took
out too much code and broke CX4 link detection in back-to-back
configuration. Put back the code that does the link check.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clear the stall bit to drop any incoming packets while destroying NIC
QP. This will prevent a chip resource leak.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set assume_aligned_header bit in QP context as requested by hardware group.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a hot-plug LLD removal event or an EEH error event, iw_cxgb3
must ensure that any/all threads that might be in a cxgb3 exported
function must return from the function before iw_cxgb3 returns from
its event processing. Do this by calling synchronize_net().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an iWARP device is unloaded, the ib_mad module logs errors. It
should be ignoring iWARP devices on device removal just like it does
on device add.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Print the return code of ib_post_send() if it fails to make these
debugging messages more useful.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPoIB UD QP reports send completions to priv->send_cq, which is
usually left unarmed; it only gets armed when the number of
outstanding send requests reaches the size of the TX queue. This
arming is done only in the send path for the UD QP. However, when
sending CM packets, the net queue may be stopped for the same reasons
but no measures are taken to recover the UD path from a lockup.
Consider this scenario: a host sends high rate of both CM and UD
packets, with a TX queue length of N. If at some time the number of
outstanding UD packets is more than N/2 and the overall outstanding
packets is N-1, and CM sends a packet (making the number of
outstanding sends equal N), the TX queue will be stopped. When all
the CM packets complete, the number of outstanding packets will still
be higher than N/2 so the TX queue will not be restarted.
Fix this by calling ib_req_notify_cq() when the queue is stopped in
the CM path.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert some drivers who export a single string as class attribute
to the new class_attr_string functions. This removes redundant
code all over.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (52 commits)
init: Open /dev/console from rootfs
mqueue: fix typo "failues" -> "failures"
mqueue: only set error codes if they are really necessary
mqueue: simplify do_open() error handling
mqueue: apply mathematics distributivity on mq_bytes calculation
mqueue: remove unneeded info->messages initialization
mqueue: fix mq_open() file descriptor leak on user-space processes
fix race in d_splice_alias()
set S_DEAD on unlink() and non-directory rename() victims
vfs: add NOFOLLOW flag to umount(2)
get rid of ->mnt_parent in tomoyo/realpath
hppfs can use existing proc_mnt, no need for do_kern_mount() in there
Mirror MS_KERNMOUNT in ->mnt_flags
get rid of useless vfsmount_lock use in put_mnt_ns()
Take vfsmount_lock to fs/internal.h
get rid of insanity with namespace roots in tomoyo
take check for new events in namespace (guts of mounts_poll()) to namespace.c
Don't mess with generic_permission() under ->d_lock in hpfs
sanitize const/signedness for udf
nilfs: sanitize const/signedness in dealing with ->d_name.name
...
Fix up fairly trivial (famous last words...) conflicts in
drivers/infiniband/core/uverbs_main.c and security/tomoyo/realpath.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
IB/srp: Clean up error path in srp_create_target_ib()
IB/srp: Split send and recieve CQs to reduce number of interrupts
RDMA/nes: Add support for KR device id 0x0110
IB/uverbs: Use anon_inodes instead of private infinibandeventfs
IB/core: Fix and clean up ib_ud_header_init()
RDMA/cxgb3: Mark RDMA device with CXIO_ERROR_FATAL when removing
RDMA/cxgb3: Don't allocate the SW queue for user mode CQs
RDMA/cxgb3: Increase the max CQ depth
RDMA/cxgb3: Doorbell overflow avoidance and recovery
IB/core: Pack struct ib_device a little tighter
IB/ucm: Clean whitespace errors
IB/ucm: Increase maximum devices supported
IB/ucm: Use stack variable 'base' in ib_ucm_add_one
IB/ucm: Use stack variable 'devnum' in ib_ucm_add_one
IB/umad: Clean whitespace
IB/umad: Increase maximum devices supported
IB/umad: Use stack variable 'base' in ib_umad_init_port
IB/umad: Use stack variable 'devnum' in ib_umad_init_port
IB/umad: Remove port_table[]
IB/umad: Convert *cdev to cdev in struct ib_umad_port
...
The iscsi_eh_target_reset has been modified to attempt
target reset only. If it fails, then iscsi_eh_session_reset
will be called.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Instead of repeating the error unwinding steps in each place an error
can be detected, use the common idiom of gotos into an error flow.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can reduce the number of IB interrupts from two interrupts per
srp_queuecommand() call to one by using separate CQs for send and
receive completions and processing send completions by polling every
time a TX IU is allocated.
Receive completion events still trigger an interrupt.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Apparently bogus mc address can break IPOIB multicast processing. Therefore
returning the check for addrlen back until this is resolved in bonding (I don't
see any other point from where mc address with non-dev->addr_len length can came
from).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the loop complexicity in nes_nic.c, I'm using char* to copy mc addresses
to it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for KR device id 0x0110. While at it, cleanup
nes_init_phy() by splitting it into nes_init_1g_phy() and
nes_init_2025_phy().
Remove support for NES_PHY_TYPE_IRIS, which was used on an XFP board
that was only manufactured in small quantities and given out for evals
in even smaller quantities.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The anon_inodes interface has been split to allow creating a bare
(non-installed) file pointer and also extended to allow specifying
O_RDONLY in the flags. This makes it a suitable replacement for the
private "infinibandeventfs" pseudo-filesystem used by uverbs, and this
replacement saves a small chunk of boilerplate code.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ib_ud_header_init() first clears header and then fills up the various
fields. Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false. Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present. Also remove unused calculation of
header_len.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If cxgb3 calls the iw_cxgb3 t3cclient remove function due to a device
removal event, then the iwch device must be marked with CXIO_ERROR_FATAL
since the device below us is going away. Otherwise, we can get stuck in
a deadlock as RDMA ULPs try and deallocate objects (like MRs, QPs, etc).
So always mark the device with CXIO_ERROR_FATAL when removing.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only kernel mode CQs need the SW queue memory allocated. The SW queue
for user mode CQs is allocated in userspace by libcxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
T3 hardware doorbell FIFO overflows can cause application stalls due
to lost doorbell ring events. This has been seen when running large
NP IMB alltoall MPI jobs. The T3 hardware supports an xon/xoff-type
flow control mechanism to help avoid overflowing the HW doorbell FIFO.
This patch uses these interrupts to disable RDMA QP doorbell rings
when we near an overflow condition, and then turn them back on (and
ring all the active QP doorbells) when when the doorbell FIFO empties
out. In addition if an doorbell ring is dropped by the hardware, the
code will now recover.
Design:
cxgb3:
- enable these DB interrupts
- in the interrupt handler, schedule work tasks to call the ULPs event
handlers with the new events.
- ring all the qset txqs when an overflow is detected.
iw_cxgb3:
- disable db ringing on all active qps when we get the DB_FULL event
- enable db ringing on all active qps and ring all active dbs when we get
the DB_EMPTY event
- On DB_DROP event:
- disable db rings in the event handler
- delay-schedule a work task which rings and enables the dbs on
all active qps.
- in post_send and post_recv logic, don't ring the db if it's disabled.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some large systems may support more than IB_UCM_MAX_DEVICES
(currently 32).
This change allows us to support more devices in a backwards-compatible
manner. the first IB_UCM_MAX_DEVICES keep the same major/minor device
numbers they've always had.
If there are more than IB_UCM_MAX_DEVICES, then we dynamically request
a new major device number (new minors start at 0).
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future
change that allows us to support more than IB_UCM_MAX_DEVICES.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future
change that allows us to dynamically allocate device numbers in case
we have more than IB_UCM_MAX_DEVICES in the system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean errors as shown when 'let c_space_errors=1' is set in vim.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some large systems may support more than IB_UMAD_MAX_PORTS
(currently 64).
This change allows us to support more ports in a backwards-compatible
manner. The first IB_UMAD_MAX_PORTS keep the same major/minor device
numbers they've always had.
If there are more than IB_UMAD_MAX_PORTS, we then dynamically request
a new major device number (new minors start at 0).
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future change
that allows us to support more than IB_UMAD_MAX_PORTS in a system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future
change that allows us to dynamically allocate device numbers in case
we have more than IB_UMAD_MAX_PORTS in the system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We no longer need this data structure, as it was used to associate an
inode back to a struct ib_umad_port during ->open(). But now that
we're embedding a struct cdev in struct ib_umad_port, we can use the
container_of() macro to go from the inode back to the device instead.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Instead of storing pointers to cdev and sm_cdev, embed the full
structures instead.
This change allows us to use the container_of() macro in ib_umad_open()
and ib_umad_sm_open() in a future patch.
This change increases the size of struct ib_umad_port to 320 bytes
from 128.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up the errors as shown when 'let c_space_errors=1' is set in vim.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eliminate some padding in the structure by rearranging the members.
sizeof(struct ib_uverbs_event_file) is now 72 bytes (from 80) and
more members now fit in the first cacheline.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some large systems may support more than IB_UVERBS_MAX_DEVICES
(currently 32).
This change allows us to support more devices in a backwards-compatible
manner. The first IB_UVERBS_MAX_DEVICES keep the same major/minor
device numbers that they've always had.
If there are more than IB_UVERBS_MAX_DEVICES, we then dynamically
request a new major device number (new minors start at 0).
This change increases the maximum number of HCAs to 64 (from 32).
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but sets us up for a future change
that allows us to support more than IB_UVERBS_MAX_DEVICES in a system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This change is not useful by itself, but it sets us up for a future
change that allows us to dynamically allocate device numbers in case
we have more than IB_UVERBS_MAX_DEVICES in the system.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dev_table's raison d'etre was to associate an inode back to a struct
ib_uverbs_device.
However, now that we've converted ib_uverbs_device to contain an
embedded cdev (instead of a *cdev), we can use the container_of()
macro and cast back to the containing device.
There's no longer any need for dev_table, so get rid of it.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Instead of storing a pointer to a cdev, embed the entire struct cdev.
This change allows us to use the container_of() macro in
ib_uverbs_open() in a future patch.
This change increases the size of struct ib_uverbs_device to 168 bytes
across 3 cachelines from 80 bytes in 2 cachelines. However, we
rearrange the members so that everything fits into the first cacheline
except for the struct cdev. Finally, we don't touch the cdev in any
fastpaths, so this change shouldn't negatively affect performance.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently the iSER receive completion flow takes the session lock
twice. Optimize it to avoid the first one by letting
iser_task_rdma_finalize() be called only from the cleanup_task
callback invoked by iscsi_free_task, thus reducing the contention on
the session lock between the scsi command submission to the scsi
command completion flows.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
libiscsi passthrough mode invokes the transport xmit calls directly
without first going through an internal queue, unlike the other mode,
which uses a queue and a xmitworker thread. Now that the "cant_sleep"
prerequisite of iscsi_host_alloc is met, move to use it. Handling
xmit errors is now done by the passthrough flow of libiscsi. Since
the queue/worker aren't used in this mode, the code that schedules the
xmitworker is removed.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove unnecessary checks for the IB connection state and for QP
overflow, as conn state changes are reported by iSER to libiscsi and
handled there. QP overflow is theoretically possible only when
unsolicited data-outs are used; anyway it's being checked and handled
by HW drivers.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Two minor flows in iSER's data path still use allocations; move them
to be atomic as a preperation step towards moving to use libiscsi
passthrough mode.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Simplify and shrink the logic/code used for the send descriptors.
Changes include removing struct iser_dto (an unnecessary abstraction),
using struct iser_regd_buf only for handling SCSI commands, using
dma_sync instead of dma_map/unmap, etc.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use a different CQ for send completions, where send completions are
polled by the interrupt-driven receive completion handler. Therefore,
interrupts aren't used for the send CQ.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that both the posting and reaping of receive buffers is done in
the completion path, the counter of outstanding buffers not be atomic.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently, the recv buffer posting logic is based on the transactional
nature of iSER which allows for posting a buffer before sending a PDU.
Change this to post only when the number of outstanding recv buffers
is below a water mark and in a batched manner, thus simplifying and
optimizing the data path. Use a pre-allocated ring of recv buffers
instead of allocating from kmem cache. A special treatment is given
to the login response buffer whose size must be 8K unlike the size of
buffers used for any other purpose which is 128 bytes.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We will make a major change in the recv buffer posting logic, after
which the problem commit bba7ebb "avoid recv buffer exhaustion caused
by unexpected PDUs" comes to solve doesn't exist any more, so revert it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change the nes driver to return -ENOMEM on SQ/RQ overflow to match the
return code of other RDMA HW drivers (e.g cxgb3, ehca, mlx4, mthca).
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Acked-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a double disconnect during AE processing, causing crashes.
While fixing the crash, also simplify the AE handling code.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a listener is destroyed and there is an MPA response pending for
loopback connection, the active side cm_node gets destroyed twice:
once in cm_event_connect_error() and again in nes_accept()/nes_reject().
Increment the cm_node's refcount so it's not destroyed by
cm_event_connect_error().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After running long iterative MPI tests, sometimes ethtool reports a
"CM Destroy Listener" count more than the "CM Create Listener" count.
This inconsistency is fixed by making counter variables atomic.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the caller does not pass a valid in_wc to process_mad(), return MAD
failure status, as it is not possible to generate a valid MAD redirect
response (and redirects are the only MAD responses ehca generates).
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Dunno, what was the idea, it wasn't used for a long time.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max_dest_rd_atomic and max_qp_rd_atomic values are properly
returned by query_qp(), so there should not be an error returned when
they are queried.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The irq_spinlock is only taken in tasklet context, so it is safe not to
disable hardware interrupts.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ib_qp already holds a pointer to the ib device. No need to dive to the
hw device object to retrieve it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure compiler won't do weird things with limits by using the
rlimit helpers added in 3e10e716 ("resource: add helpers for fetching
rlimits"). E.g. fetching them twice may return 2 different values
after writable limits are implemented.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As of commit f56bcd8 ("IPoIB: Use separate CQ for UD send
completions"), there are no TX interrupts. Change the ethtool code
not to report TX moderation settings, so users will not be misled to
think they can control TX interrupt moderation. Pointed out by Alex
Vainman <alexv@voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Failure to rearm a CQ means the cxgb3 device is wedged, but we shouldn't
kill the whole system with a BUG_ON() if this happens.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cm: Revert association of an RDMA device when binding to loopback
Revert the following change from commit 6f8372b6 ("RDMA/cm: fix
loopback address support")
The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address. (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdma_bind_addr,
no device is associated with the rdma_cm_id. Fix this.
It turns out that important apps such as Open MPI depend on
rdma_bind_addr() NOT associating any RDMA device when binding to a
loopback address. Open MPI is being updated to deal with this, but at
least until a new Open MPI release is available, maintain the previous
behavior: allow rdma_bind_addr() to succeed, but do not bind to a
device.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct misspelled "CONFIG_IPv6" that was introduced in commit
d14714df ("IB/addr: Fix IPv6 routing lookup"). The config variable
should be all uppercase.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[ This was my fault when I munged the original patch. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mlx4_ib_post_recv(), we should check the queue for overflow using
recv_cq instead of send_cq (current code looks like a copy-and-paste
mistake).
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As for memfree mthca hardware, ConnectX also requires SRQ WQE scatter
entries to be initialized with the invalid L_Key at SRQ creation time.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the "ignoring return value of '...', declared with attribute
warn_unused_result" compiler warning in several users of the new kfifo
API.
It removes the __must_check attribute from kfifo_in() and
kfifo_in_locked() which must not necessary performed.
Fix the allocation bug in the nozomi driver file, by moving out the
kfifo_alloc from the interrupt handler into the probe function.
Fix the kfifo_out() and kfifo_out_locked() users to handle a unexpected
end of fifo.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rename kfifo_put... into kfifo_in... to prevent miss use of old non in
kernel-tree drivers
ditto for kfifo_get... -> kfifo_out...
Improve the prototypes of kfifo_in and kfifo_out to make the kerneldoc
annotations more readable.
Add mini "howto porting to the new API" in kfifo.h
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the pointer to the spinlock out of struct kfifo. Most users in
tree do not actually use a spinlock, so the few exceptions now have to
call kfifo_{get,put}_locked, which takes an extra argument to a
spinlock.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new generic kernel FIFO implementation.
The current kernel fifo API is not very widely used, because it has to
many constrains. Only 17 files in the current 2.6.31-rc5 used it.
FIFO's are like list's a very basic thing and a kfifo API which handles
the most use case would save a lot of development time and memory
resources.
I think this are the reasons why kfifo is not in use:
- The API is to simple, important functions are missing
- A fifo can be only allocated dynamically
- There is a requirement of a spinlock whether you need it or not
- There is no support for data records inside a fifo
So I decided to extend the kfifo in a more generic way without blowing up
the API to much. The new API has the following benefits:
- Generic usage: For kernel internal use and/or device driver.
- Provide an API for the most use case.
- Slim API: The whole API provides 25 functions.
- Linux style habit.
- DECLARE_KFIFO, DEFINE_KFIFO and INIT_KFIFO Macros
- Direct copy_to_user from the fifo and copy_from_user into the fifo.
- The kfifo itself is an in place member of the using data structure, this save an
indirection access and does not waste the kernel allocator.
- Lockless access: if only one reader and one writer is active on the fifo,
which is the common use case, no additional locking is necessary.
- Remove spinlock - give the user the freedom of choice what kind of locking to use if
one is required.
- Ability to handle records. Three type of records are supported:
- Variable length records between 0-255 bytes, with a record size
field of 1 bytes.
- Variable length records between 0-65535 bytes, with a record size
field of 2 bytes.
- Fixed size records, which no record size field.
- Preserve memory resource.
- Performance!
- Easy to use!
This patch:
Since most users want to have the kfifo as part of another object,
reorganize the code to allow including struct kfifo in another data
structure. This requires changing the kfifo_alloc and kfifo_init
prototypes so that we pass an existing kfifo pointer into them. This
patch changes the implementation and all existing users.
[akpm@linux-foundation.org: fix warning]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (38 commits)
direct I/O fallback sync simplification
ocfs: stop using do_sync_mapping_range
cleanup blockdev_direct_IO locking
make generic_acl slightly more generic
sanitize xattr handler prototypes
libfs: move EXPORT_SYMBOL for d_alloc_name
vfs: force reval of target when following LAST_BIND symlinks (try #7)
ima: limit imbalance msg
Untangling ima mess, part 3: kill dead code in ima
Untangling ima mess, part 2: deal with counters
Untangling ima mess, part 1: alloc_file()
O_TRUNC open shouldn't fail after file truncation
ima: call ima_inode_free ima_inode_free
IMA: clean up the IMA counts updating code
ima: only insert at inode creation time
ima: valid return code from ima_inode_alloc
fs: move get_empty_filp() deffinition to internal.h
Sanitize exec_permission_lite()
Kill cached_lookup() and real_lookup()
Kill path_lookup_open()
...
Trivial conflicts in fs/direct-io.c
Always set bad_wr when an immediate error is detected. Return ENOMEM
for queue full instead of EINVAL to match other drivers.
Signed-off-by: Frank Zago <fzago@systemfabricworks.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
When the remote node's ethernet address changes, the connection keeps
trying to connect using the old address. The connection wil continue
failing until the driver is unloaded and loaded again (eiter reboot or
rmmod). Fix this by checking that the NIC has the correct address
before starting a connection.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A FIN that is received during an MPA start up sequence causes a
timeout in iwcm.c. The connection has not been completely closed so
the iwcm code is waiting for resources to be cleaned up. This closes
the connection so everything cleans up correctly.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We fail when creating many qps as kmap() fails for sq_vbase.
Fix this by doing kunmap() as soon as we are done with sq_vbase.
We do kunmap() in one of the locations below:
(1) nes_destroy_qp()
(2) nes_accept()
(3) nes_connect_event
We keep a flag to avoid multiple calls to kunmap().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
STags are generated randomly but the driver does not correctly prevent
a zero STag. Using STag zero is privileged and causes a user space
application to fail. This change prevents the driver from trying to
allocate a zero STag.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
While running a Xansation test, an active side node crashed. The
problem started on the passive side, which generated an STtag that was
0. The passive side sent a TERMINATE instead of an MPA REJECT msg.
The active side, receives TERMINATE and sends connect_err() and set
the cm_node state to CLOSED. The passive side sends FIN + ACK after
TERMINATE. Active side ends up in handle_ack_pkt() and send_reset().
send_reset() consumes 1 cm_node's ref_count. Because the cm_node is
in CLOSED state, which means that cm_node will be destroyed after
completion of the connect_err() indication, CM will crash after
send_reset().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the listener is destroyed for a loopback connection, the listener
node gets a reset event. This causes a crash as the listener is not
expecting a reset event. Code review of cm_event_reset() during
debugging showed the cm_id ref count is incremented after calling its
event handler and not before.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
While running IMP_EXT's window test, we saw a crash in nes_accept().
Here is the sequence of what happened:
(1) In MVAPICH2, connect request is received for port #0.
FIX: Add a nes_connect() check to make sure local or remote tcp port
is not 0.
(2) Remote node's (passive) TCP stack sends a reset when it gets a
connect request because of port = 0. Active side set the connect
error to IW_CM_EVENT_STATUS_REJECTED when it received the RST from
remote node.
FIX: The corect error code is -ECONNRESET.
(3) Wrong error code of IW_CM_EVENT_STATUS_REJECTED causes the core to
destroy its listener ports. Here there are connections that may
have sent an MPA request up and waiting for accept or reject. But
the listener and its cm_nodes have been freed already causing the
crash noticed.
FIX: The cm_node is freed only if its state is not
NES_CM_STATE_MPAREQ_RCVD. If cm_node's state is
NES_CM_STATE_MPAREQ_RCVD then its new state is set to
NES_CM_STATE_LISTENER_DESTROYED and it is not freed. When
nes_accept() or nes_reject() is received, its state is checked
for NES_CM_STATE_LISTENER_DESTROYED and in this case the cm_node
is freed and error is returned.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During testing of REJECT connection error handling, we saw that the
cm_id resources are not released. When the retransmit timer expires,
we need to send a reset message to remote node before issuing the
ABORTED event.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During Xansation testing, we saw that error handling of MPA frame
msg/response is not handled properly.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
