Usual drill applies. Again I've not switched the upcast helpers to use
intel_encoder instead of drm_encoder since that's much more invasive
and will change also the hdmi and ddi encoders.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The w/a db makes the recommendation to both use a non-default value for
the initial clock and then to retry with an alternative clock for
Haswell with the Lakeport PCH.
"On LPT:H, use a divider value of 63 decimal (03Fh). If there is a
failure, retry at least three times with 63, then retry at least three
times with 72 decimal (048h)."
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This backmerges Linus' merge commit of the latest drm-fixes pull:
commit 549f3a1218
Merge: 42577ca058ca4a
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue Jul 23 15:47:08 2013 -0700
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
We've accrued a few too many conflicts, but the real reason is that I
want to merge the 100% solution for Haswell concurrent registers
writes into drm-intel-next. But that depends upon the 90% bandaid
merged into -fixes:
commit a7cd1b8fea
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 19 20:36:51 2013 +0100
drm/i915: Serialize almost all register access
Also, we can roll up on accrued conflicts.
Usually I'd backmerge a tagged -rc, but I want to get this done before
heading off to vacations next week ;-)
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem.c
v2: For added hilarity we have a init sequence conflict around the
gt_lock, so need to move that one, too. Spotted by Jani Nikula.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to decypher detection failures is a little tricker at the moment as
the only indicator of progress is when output_poll_execute() tells us
the result after the connector->detect() has run. This patch adds a
telltale to the start of each detect function so that we can track
progress and associate activity more clearly with each connector.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Restore debug message lost in merge commit e1b73cba13. Also clarify it
that we are only clamping bpp not overwriting it.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required function to disable PSR when going to console mode.
But also can be used whenever PSR mode entry conditions changed.
v2: Add it before PSR Hook. Update function not really been called yet.
v3: Fix coding style detected by checkpatch by Paulo Zanoni.
v4: do_enable must be static as Paulo noticed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: prefer seq_puts to seq_printf detected by Paulo Zanoni.
v3: PSR is disabled by default. Without userspace ready it
will cause regression for kde and xdm users
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Prefer seq_puts to seq_printf by Paulo Zanoni.
v3: small changes like avoiding calling dp_to_dig_port twice as noticed by
Paulo Zanoni.
v4: Avoiding reading non-existent registers - noticed by Paulo
on first psr debugfs patch.
v5: Accepting more suggestions from Paulo:
* check sw interlace flag instead of i915_read
* introduce PSR_S3D_ENABLED to avoid forgeting it whenever added.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Fix up debugfs output (spotted by Paulo) and rip out the
power well check since we really can't do that in a race-free manner,
so it's bogus.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding Enable and Disable PSR functionalities. This includes setting the
PSR configuration over AUX, sending SDP VSC DIP over the eDP PIPE config,
enabling PSR in the sink via DPCD register and finally enabling PSR on
the host.
This patch is based on initial PSR code by Sateesh Kavuri and Kumar Shobhit
but in a different implementation.
v2: * moved functions around and changed its names.
* removed VSC DIP unset from disable.
* remove FBC wa.
* don't mask LSPS anymore.
* incorporate new crtc usage after a rebase.
v3: Make a clear separation between Sink (Panel) and Source (HW) enabling.
v4: Fix identation and other style issues raised by checkpatch (by Paulo).
v5: Changes according to Paulo's review:
static on write_vsc;
avoid using dp_to_dev when already calling dp_to_dig_port;
remove unecessary TP default time setting;
remove unecessary interrupts disabling;
remove unecessary wait_for_vblank when disabling psr;
v6: remove unecessary wait_for_vblank when writing vsc;
v7: adding setup once function to avoid unnecessarily write to vsc
and set debug_ctl every time we enable or disable psr.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Credits-by: Sateesh Kavuri <sateesh.kavuri@intel.com>
Credits-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Apply Paulo's suggestion for unconditionally clearing the
control register when writing the DIP.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: reuse of just created is_edp_psr and put it at right place.
v3: move is_edp_psr above intel_edp_disable
v4: remove parentheses. Noticed by Paulo.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP 1.2 compatible displays may report a 5.4Gbps maximum bandwidth which
the driver will treat as an invalid value and use 1.62Gbps instead. Fix
this by capping to 2.7Gbps for sinks reporting a 5.4Gbps max bw.
Also add a warning for reserved values.
v2:
- allow only bw values explicitly listed in the DP standard (Daniel,
Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this for comparing modes between configuration changes.
The tricky part is to allow us to reuse the new get_clock stuff to
recover the lvds clock on gen2/3 when neither the vbt has an lvds mode
nor the panel a (useful) EDID.
v2: try harder to calulate non-simple pixel clocks (Daniel)
call get_clock after getting the encoder config, needed for pixel multiply
(Jesse)
v3: drop get_clock now that the pixel_multiply has been moved into
get_pipe_config
v4: re-add get_clock; we need to get the pixel multiplier in the
encoder, so need to calculate the clock value after the encoder's
get_config is called
v5: drop hsw clock_get, still needs to be written
v6: add fuzzy clock check (Daniel)
v7: wrap fuzzy clock check under !IS_HASWELL
use port_clock field rather than a new CPU eDP clock field in crtc_config
v8: remove stale pixel_multiplier sets (Daniel)
multiply by pixel_multiplier in 9xx clock get too (Daniel)
v9: make sure we set pixel_multiplier before calling clock_get from mode_get
for LVDS (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add some explanation to the commit message about why we have
to jump through a few hoops. Also remove the rebase-fail hunk from
intel_sdvo.c]
[danvet: Squash in the fixup from Jesse to also call ->get_clock in
the modeset state checker.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On DevCPT, the control register for Transcoder DP Sync Polarity is
TRANS_DP_CTL, not DP_CTL.
Without this patch, Many call trace occur on CPT machine with DP monitor.
The call trace is like: *ERROR* mismatch in adjusted_mode.flags(expected X,found X)
v2: use intel-crtc to simple patch, suggested by Daniel.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
[danvet: Extend the encoder->get_config comment to specify that we now
also depend upon intel_encoder->base.crtc being correct. Also bikeshed
s/intel_crtc/crtc/.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65287
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because it's the function that destroys the connector, not the
encoder. And we already have intel_dp_encoder_destroy.
This has annoyed me for a long time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've been ignoring this return value, so print a nice backtrace in
case it's not what we expected.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because calling intel_dp_encoder_destroy inside
intel_edp_init_connector is just wrong. This is the initialization
path, so we should properly unwind all the initialization through the
whole caller stack.
On the intel_dp_encoder_destroy function we do the following:
1 - Call i2c_del_adapter
2 - Call drm_encoder_cleanup
3 - If edp:
3.1 - Cancel panel_vdd_work
3.2 - Call ironlake_panel_vdd_of_sync
4 - Free the encoder
And here is how we unwind each specific step:
1 - We have intel_dp_init_connector -> intel_dp_i2c_init ->
i2c_dp_aux_add_bus -> i2c_add_adapter, so we call
i2c_del_dapter at intel_dp_init_connector
2 - Call it in the same function that called drm_encoder_init
3 - Call it in the same function that called INIT_DELAYED_WORK
4 - Free it in the same function that allocated it
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because calling intel_dp_destroy inside intel_edp_init_connector is
just wrong. This is the initialization path, so we should properly
unwind all the initialization through the whole caller stack.
On the intel_dp_destroy function we do the following:
1 - Free edid if it exists
2 - Call intel_panel_fini in case it's eDP
3 - Call drm_sysfs_connector_remove
4 - Call drm_connector_cleanup
5 - Free the connector
And here is how we unwind each specific step:
1 - No need as we still didn't assign anything
2 - No need as we still didn't call intel_panel_init
3 - Call it in the same function that called drm_sysfs_connector_add
4 - Call it in the same function that called drm_connector_init
5 - Free it in the same function that allocated it
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we detect a "ghost eDP", intel_edp_init_connector frees both
the connector and encoder and then returns. On Haswell, intel_ddi_init
then tries to use the freed encoder on the HDMI initialization path
since the following commit:
commit 21a8e6a485
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 10 23:28:35 2013 +0200
drm/i915: don't setup hdmi for port D edp in ddi_init
So now on intel_ddi_init we check for the "ghost eDP" case and return
without trying to initialize HDMI. This way we won't try to read the
freed "intel_encoder" struct in the next "if" statement.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because intel_dp_init_connector is too big for my poor little brain.
No functional changes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By the time we call intel_dp_destroy (which destroys the connector)
the encoder may have been destroyed already, so if we use it we may be
reading some free memory. That happens in drm_mode_config_cleanup()
and also inside intel_dp_init_connector() when we detect a ghost eDP.
I also hope this may solve some random memory bugs.
Reported by kmemcheck.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Last 3.11 feature pull. I have a few odds bits and pieces and fixes in my
queue, I'll sort them out later on to see what's for 3.11-fixes and what's
for 3.12. But nothing to hold this here up imo.
Highlights:
- more hangcheck work from Mika and Chris to prepare for arb robustness
- trickle feed fixes from Ville
- first parts of the shared pch pll rework, with some basic hw state
readout and cross-checking (this shuts up the confused pch pll refcount
WARN that Linus just recently forwarded)
- Haswell audio power well support from Wang Xingchao (alsa bits acked by
Takashi)
- some cleanups and asserts sprinkling around the plane/gamma enabling
sequence from Ville
- more gtt refactoring from Ben
- clear up the adjusted->mode vs. pixel clock vs. port clock confusion
- 30bpp support, this time for real hopefully
* tag 'drm-intel-next-2013-06-18' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: remove a superflous semi-colon
drm/i915: Kill useless "Enable panel fitter" comments
drm/i915: Remove extra "ring" from error message
drm/i915: simplify the reduced clock handling for pch plls
drm/i915: stop killing pfit on i9xx
drm/i915: explicitly set up PIPECONF (and gamma table) on haswell
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
drm/i915: set up PIPECONF explicitly on ilk-ivb
drm/i915: find guilty batch buffer on ring resets
drm/i915: store ring hangcheck action
drm/i915: add batch bo to i915_add_request()
drm/i915: change i915_add_request to macro
drm/i915: add i915_gem_context_get_hang_stats()
drm/i915: add struct i915_ctx_hang_stats
drm/i915: Try harder to disable trickle feed on VLV
drm/i915: fix up pch pll enabling for pixel multipliers
drm/i915: hw state readout and cross-checking for shared dplls
drm/i915: WARN on lack of shared dpll
drm/i915: split up intel_modeset_check_state
drm/i915: extract readout_hw_state from setup_hw_state
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_fb.c
drivers/gpu/drm/i915/intel_sdvo.c
Daniel writes:
Another round of drm-intel-next for 3.11. Highlights:
- Haswell IPS support (Paulo Zanoni)
- VECS support on Haswell (Ben Widawsky, Xiang Haihao, ...)
- Haswell watermark fixes (Paulo Zanoni)
- "Make the gun bigger again" multithread fence fix from Chris.
- i915_error_state finnally no longer fails with -ENOMEM! Big thanks to
Mika for tackling this.
- vlv sideband locking fixes from Jani
- Hangcheck prep work for arb_robustness support (Mika&Chris)
- edp vs cpu port confusion clean-up from Imre
- pile of smaller fixes and cleanups all over.
* tag 'drm-intel-next-2013-06-01' of git://people.freedesktop.org/~danvet/drm-intel: (70 commits)
drm/i915: add i915_ips_status debugfs entry
drm/i915: add enable_ips module option
drm/i915: implement IPS feature
drm/i915: fix up the edp power well check
drm/i915: add I915_PARAM_HAS_VEBOX to i915_getparam
drm/i915: add I915_EXEC_VEBOX to i915_gem_do_execbuffer()
drm/i915: add VEBOX into debugfs
drm/i915: Enable vebox interrupts
drm/i915: vebox interrupt get/put
drm/i915: consolidate interrupt naming scheme
drm/i915: Convert irq_refounct to struct
drm/i915: make PM interrupt writes non-destructive
drm/i915: Add PM regs to pre/post install
drm/i915: Create an ivybridge_irq_preinstall
drm/i915: Create a more generic pm handler for hsw+
drm/i915: add support for 5/6 data buffer partitioning on Haswell
drm/i915: properly set HSW WM_LP watermarks
drm/i915: properly set HSW WM_PIPE registers
drm/i915: fix pch_nop support
drm/i915: Vebox ringbuffer init
...
We always limited the link bw calculations to 24bpp. Tested with
my shiny new high-bpc screen, seems to work as advertised.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65280
Tested-by: shui yangwei <yangweix.shui@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prepares a bit for the next big patch, where we switch the
semantics of the different clocks in the pipe config around.
Since I've broken cpu eDP PLL handling in the first version I've
figured some refactoring is in order.
Split out on request from Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The patch changes all remaining is_cpu_edp() check with a check for port
A. We can do this, since in all these cases ValleyView is handled
separately and port A is always a CPU side eDP port.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On ValleyView for both eDP and DP the AUX input clock is 200MHz, so we
can calculate for both the clock divider for the 2MHz target rate at the
same place. Afterwards we can also replace the is_cpu_edp() check with a
check for port A.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on 3739850b46 - "drm/i915: disable the cpu edp port after the
cpu pipe" and the bspec disabling sequence for IVB and older it seems we
have to distinguish only the CPU vs. PCH port case, whether it's a DP or
eDP doesn't seem to matter. For IVB and older on the CPU side we can
only have eDP on port A, DP ports can only be on the PCH side. On VLV we
have only CPU side eDP/DP ports, no PCH. So the condition for the
disabling sequence we need for CPU ports is port == A || IS_VLV.
This allows us to remove is_cpu_edp() completely in a later patch.
v2:
- simplify (and fix) the condition for CPU side ports and adjust the
commit message accordingly (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
Highlights (copy-pasted from my testing cycle mails):
- fbc support for Haswell (Rodrigo)
- streamlined workaround comments, including an igt tool to grep for
them (Damien)
- sdvo and TV out cleanups, including a fixup for sdvo multifunction devices
- refactor our eDP mess a bit (Imre)
- don't register the hdmi connector on haswell when desktop eDP is present
- vlv support is no longer preliminary!
- more vlv fixes from Jesse for stolen and dpll handling
- more flexible power well checking infrastructure from Paulo
- a few gtt patches from Ben
- a bit of OCD cleanups for transcoder #defines and an assorted pile
of smaller things.
- fixes for the gmch modeset sequence
- a bit of OCD around plane/pipe usage (Ville)
- vlv turbo support (Jesse)
- tons of vlv modeset fixes (Jesse et al.)
- vlv pte write fixes (Kenneth Graunke)
- hpd filtering to avoid costly probes on unaffected outputs (Egbert Eich)
- intel dev_info cleanups and refactorings (Damien)
- vlv rc6 support (Jesse)
- random pile of fixes around non-24bpp modes handling
- asle/opregion cleanups and locking fixes (Jani)
- dp dpll refactoring
- improvements for reduced_clock computation on g4x/ilk+
- pfit state refactored to use pipe_config (Jesse)
- lots more computed modeset state moved to pipe_config, including readout
and cross-check support
- fdi auto-dithering for ivb B/C links, using the neat pipe_config
improvements
- drm_rect helpers plus sprite clipping fixes (Ville)
- hw context refcounting (Mika + Ben)
* tag 'drm-intel-next-2013-05-20-merged' of git://people.freedesktop.org/~danvet/drm-intel: (155 commits)
drm/i915: add support for dvo Chrontel 7010B
drm/i915: Use pipe config state to control gmch pfit enable/disable
drm/i915: Use pipe_config state to disable ilk+ pfit
drm/i915: panel fitter hw state readout&check support
drm/i915: implement WADPOClockGatingDisable for LPT
drm/i915: Add missing platform tags to FBC workaround comments
drm/i915: rip out an unused lvds_reg variable
drm/i915: Compute WR PLL dividers dynamically
drm/i915: HSW FBC WaFbcDisableDpfcClockGating
drm/i915: HSW FBC WaFbcAsynchFlipDisableFbcQueue
drm/i915: Enable FBC at Haswell.
drm/i915: IVB FBC WaFbcDisableDpfcClockGating
drm/i915: IVB FBC WaFbcAsynchFlipDisableFbcQueue
drm/i915: Add support for FBC on Ivybridge.
drm/i915: Organize VBT stuff inside drm_i915_private
drm/i915: make SDVO TV-out work for multifunction devices
drm/i915: rip out now unused is_foo tracking from crtc code
drm/i915: rip out TV-out lore ...
drm/i915: drop TVclock special casing on ilk+
drm/i915: move sdvo TV clock computation to intel_sdvo.c
...
Rename all VLV IOSF sideband register accessor functions to
vlv_<port>_{read,write}. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During DP AUX communication we might time out 1 jiffy too early, because
the calculated expiry jiffy value is one less than needed.
This is only one reason for false DP AUX timeouts. For a complete
solution we also need the following fix, which is now queued for
mainline: http://marc.info/?l=linux-kernel&m=136748515710837&w=2
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64133
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this, that 338 can finally become the correct 337500.
Due to the change we need to adjust the intel_dp_aux_ch function to
set the correct value, so adjust the division and also use
DIV_ROUND_CLOSEST instead of the old "round down" behavior because the
spec says the value "should be programmed to get as close as possible
to the ideal rate of 2MHz".
Quoting Paulo's follow-up to a question from Chris Wilson to explain
what exactly will change:
I use the 337500 value on the next patch, when setting the
ips_linetime value. The correct frequency is 337500, not 338000.
ips_linetime = DIV_ROUND_CLOSEST(mode->htotal * 1000 * 8,
intel_ddi_get_cdclk_freq);
For a mode with htotal of 2640 [0] we'll have: (i) (2640 * 1000 * 8) /
338000 = 62.48, resulting in 62 and (ii) (2640 * 1000 * 8) / 337500 =
62.57 resulting in 63.
For the case inside intel_dp.c:
Previously we were using 338. So with the old formula we were writing
338/2 = 169 to the register. And 337500 / 169 = 1997.04 (we use 337500
here because it's the real clock value). With the new value of
337500/2000 we'll have 168.75, which is 168 on the round-down case and
169 on the round-closest case. If we write 168 to the register, 337500
/ 168 = 2008.92, and 2008.92 is more distant from 2000 than 1997.04.
So with this patch we're changing the formula but still writing the
same correct value to the DP AUX register.
[0]: That's 1920x1080@50Hz on my DP monitor.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Pimp the commit message with Paulo's follow-up.]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can use this for fetching encoder specific pipe_config state, like
mode flags, adjusted clock, etc.
Just used for mode flags atm, so we can check the pipe config state at
mode set time.
v2: get_config when checking hw state too
v3: fix DVO and LVDS mode flags (Ville)
get SDVO DTD for flag fetch (Ville)
v4: use input timings (Ville)
correct command used (Ville)
remove gen4 check (Ville)
v5: get DDI flag config too
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Tested-by: Paulo Zanoni <przanoni@gmail.com> (the new hsw ddi stuff)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRmpexAAoJEHm+PkMAQRiGrRIH/1uWFW38RvaCV/PXm/ia6Z+x
BfBJfBIvPxGwb4n7aQNQlhU25xkfrPZ6szO4WiBH5/KPH3xYi2I2OZ1AzffkYqMF
BWkPmsPK6EsTdp16zsi6JtH2aXArG4SpYA7ZamPvDkmfigHuiZg7GlL/9eHTRPNV
P7Q8JToOrcnP8RoGgNj0uFiQeQbc62Kmoq7WuPtUhVlpQCCCknXgOJiYgz9w6Xe9
/i79YFS8WRrzAquExT1NbIOh4ZMqB9MvuroaVWy8JDDLUyz7QUvOCe3tCDNguwgi
FdWvU6nfkdQq5SLaWCWXDE9Rp/pL1MvfBn9vCOwFcp42aw0aQ0PgJVIXvsqufd0=
=jgDI
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc2' into drm-intel-next-queued
Backmerge Linux 3.10-rc2 since the various (rather trivial) conflicts
grew a bit out of hand. intel_dp.c has the only real functional
conflict since the logic changed while dev_priv->edp.bpp was moved
around.
Also squash in a whitespace fixup from Ben Widawsky for
i915_gem_gtt.c, git seems to do something pretty strange in there
(which I don't fully understand tbh).
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"Just a few straggling fixes I hoovered up, and an intel fixes pull
from Daniel which fixes some regressions, and some mgag200 fixes from
Matrox."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/mgag200: Fix framebuffer base address programming
drm/mgag200: Convert counter delays to jiffies
drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
drm/mgag200: Don't change unrelated registers during modeset
drm: Only print a debug message when the polled connector has changed
drm: Make the HPD status updates debug logs more readable
drm: Use names of ioctls in debug traces
drm: Remove pointless '-' characters from drm_fb_helper documentation
drm: Add kernel-doc for drm_fb_helper_funcs->initial_config
drm: refactor call to request_module
drm: Don't prune modes loudly when a connector is disconnected
drm: Add missing break in the command line mode parsing code
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
drm_i915_private is getting bigger and bigger when adding new vbt stuff.
So, the better way of getting drm_i915_private organized is to create
a special structure for vbt stuff.
v2: Basically conflicts fixes
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users for these, so remove them.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
is_pch_edp() will be removed by the next patch, so replace it by a check
for the port and device type.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
is_pch_edp() will be removed in a follow-up patch, so replace it
with a check for the port and VBT info (for port-D eDP).
Also make things a bit clearer by using a switch on the ports.
v2:
- make the comment about not setting the conder type for DP clearer
(Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
A few intel fixes for smaller issues and one revert for an sdv hack which
we've wanted to kill anyway. Plus two drm patches included for your
convenience, both regression fixers for mine own screw-ups.
+ both fixes for stolen mem handling.
* 'for-linux-next' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
According to BSpec the link training sequence for eDP on HSW port-A
should be as follows:
1. link training: clock recovery
2. link training: equalization
3. link training: set idle transmission mode
4. display pipe enable
5. link training: disable (set normal mode)
Contrary to this at the moment we don't do step 3. and we do step 5.
before step 4. Fix this by setting idle transmission mode for eDP at
the end of intel_dp_complete_link_train and adding a new
intel_dp_stop_link_training function to disable link training. With
these changes we'll end up with the following functions corresponding
to the above steps:
intel_dp_start_link_train -> step 1.
intel_dp_complete_link_train -> step 2., step 3.
intel_dp_stop_link_train -> step 5.
For port-A we'll call intel_dp_stop_link_train only after enabling the
pipe, for everything else we'll call it right after
intel_dp_complete_link_train to preserve the current behavior.
Tested on HSW/HSW-ULT.
In v2:
- Due to a HW issue we must set idle transmission mode for port-A too
before enabling the pipe. Thanks for Arthur Runyan for explaining
this.
- Update the patch subject to make it clear that it's an eDP fix, DP is
not affected.
v3:
- rename intel_dp_link_train() to intel_dp_set_link_train(), use 'val'
instead 'l' as var name. (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 57c2196332.
It's an ugly hack for a Haswell SDV platform where the vbt doesn't
seem to fully agree with the panel. Since it seems to cause issues on
real eDP platform let's just kill this hack again.
Reported-and-tested-by: Josh Boyer <jwboyer@gmail.com>
References: https://lkml.org/lkml/2013/5/3/467
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 3.10.
Wierd bits:
- OMAP drm changes required OMAP dss changes, in drivers/video, so I
took them in here.
- one more fbcon fix for font handover
- VT switch avoidance in pm code
- scatterlist helpers for gpu drivers - have acks from akpm
Highlights:
- qxl kms driver - driver for the spice qxl virtual GPU
Nouveau:
- fermi/kepler VRAM compression
- GK110/nvf0 modesetting support.
Tegra:
- host1x core merged with 2D engine support
i915:
- vt switchless resume
- more valleyview support
- vblank fixes
- modesetting pipe config rework
radeon:
- UVD engine support
- SI chip tiling support
- GPU registers initialisation from golden values.
exynos:
- device tree changes
- fimc block support
Otherwise:
- bunches of fixes all over the place."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (513 commits)
qxl: update to new idr interfaces.
drm/nouveau: fix build with nv50->nvc0
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
...
If we ever leak a non-DP compliant port width through here, we have a
pretty serious issue. So just rip out all these WARNs - if we need
them it's probably better to have them at a central place where we
compute the dp lane count.
Also use the new DDI width macro for FDI mode.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixup the embarrassing s/intel_dp->DP/temp/ mistake Paulo
spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
