dma_map_single does not work for vmalloc-ed buffers,
so disable DMA in this case.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reported-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Tested-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The block responsible of parsing the DT for the number of chip-select
lines uses an 'if/else if/else if' block. The content of the second and
third 'else if' conditions are:
1/ the actual condition to enter the sub-block and
2/ the operation to do in this sub-block.
[...]
else if (condition1_to_enter && action1() == failed)
raise_error();
else if (condition2_to_enter && action2() == failed)
raise_error();
[...]
In case of failure, the sub-block is entered and an error raised.
Otherwise, in case of success, the code would continue erroneously in
the next 'else if' statement because it did not failed (and did not
enter the first 'else if' sub-block).
The first 'else if' refers to legacy bindings while the second 'else if'
refers to new bindings. The second 'else if', which is entered
erroneously, checks for the 'reg' property, which, for old bindings,
does not mean anything because it would not be the number of CS
available, but the regular register map of almost any DT node. This
being said, the content of the 'reg' property being the register map
offset and length, it has '2' values, so the number of CS in this
situation is assumed to be '2'.
When running nand_scan_ident() with 2 CS, the core will check for an
array of chips. It will first issue a RESET and then a READ_ID. Of
course this will trigger two timeouts because there is no chip in front
of the second CS:
[ 1.367460] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000080)
[ 1.474292] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000280)
Indeed, this is harmless and the core will then assume there is only one
valid CS.
Fix the logic in the whole block by entering each sub-block just on the
'is legacy' condition, doing the action inside the sub-block. This way,
when the action succeeds, the whole block is left.
Furthermore, for both the old bindings and the new bindings the same
logic was applied to retrieve the number of CS lines:
using of_get_property() to get a size in bytes, converted in the actual
number of lines by dividing it per sizeof(u32) (4 bytes).
This is fine for the 'reg' property which is a list of the CS IDs but
not for the 'num-cs' property which is directly the value of the number
of CS.
Anyway, no existing DT uses another value than 'num-cs = <1>' and no
other value has ever been supported by the old driver (pxa3xx_nand.c).
Remove this condition and apply a number of 1 CS anyway, as already
described in the bindings.
Finally, the 'reg' property of a 'nand' node (with the new bindings)
gives the IDs of each CS line in use. marvell_nand.c driver first look
at the number of CS lines that are present in this property.
Better use of_property_count_elems_of_size() than dividing by 4 the size
of the number of bytes returned by of_get_property().
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit e7bfb3fdbd ("mtd: Stop updating erase_info->state and calling
mtd_erase_callback()") removed the einfo->state field and the
MTD_ERASE_XXX macros. At the same time, the generic NAND layer was added
and made sure to update the erase info state.
It did not result in a build failure after merging the nand/for-4.17
branch in mtd/next because the generic NAND layer is not selected yet.
Let's fix that before a config option starts selecting MTD_NAND_CORE.
Fixes: e7bfb3fdbd ("mtd: Stop updating erase_info->state and calling mtd_erase_callback()")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Use devm_clk_get() to let Linux manage struct clk memory.
Fixes: 6956e2385a ("add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Reported-by: Xidong Wang <wangxidong_97@163.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core:
* Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
* Remove Cyrille from the list of SPI NOR and MTD maintainers
* Fix kernel doc headers
* Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
* Remove the bfin-async-flash driver (the only architecture using
it has been removed)
* Fix pagetest test
* Add extra checks in mtd_erase()
* Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
Drivers:
* Add endianness information to the physmap DT binding
* Add Eon EN29LV400A IDs to JEDEC probe logic
* Use %*ph where appropriate
SPI NOR changes:
Drivers:
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND changes:
Core:
* Prepare arrival of the SPI NAND subsystem by implementing a
generic (interface-agnostic) layer to ease manipulation of NAND
devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Drivers:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=EG7L
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD Core:
- Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
- Remove Cyrille from the list of SPI NOR and MTD maintainers
- Fix kernel doc headers
- Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
- Remove the bfin-async-flash driver (the only architecture using it
has been removed)
- Fix pagetest test
- Add extra checks in mtd_erase()
- Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
MTD Drivers:
- Add endianness information to the physmap DT binding
- Add Eon EN29LV400A IDs to JEDEC probe logic
- Use %*ph where appropriate
SPI NOR Drivers:
- Make fsl-quaspi assign different names to MTD devices connected to
the same QSPI controller
- Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND Core:
- Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
- Move onenand code base to the drivers/mtd/nand/ dir
- Rework timing mode selection
- Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
- Stop embedding ONFI/JEDEC param page in nand_chip
NAND Drivers:
- Rework/cleanup of the mxc driver
- Various cleanups in the vf610 driver
- Migrate the fsmc and vf610 to ->exec_op()
- Get rid of the pxa driver (replaced by marvell_nand)
- Support ->setup_data_interface() in the GPMI driver
- Fix probe error path in several drivers
- Remove support for unused hw_syndrome mode in sunxi_nand
- Various minor improvements"
* tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits)
dt-bindings: fsl-quadspi: Add the example of two SPI NOR
mtd: fsl-quadspi: Distinguish the mtd device names
mtd: nand: Fix some function description mismatches in core.c
mtd: fsl-quadspi: Remove unneeded driver.bus assignment
mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
mtd: rawnand: s3c2410: enhance the probe function error path
mtd: rawnand: tango: fix probe function error path
mtd: rawnand: sh_flctl: fix the probe function error path
mtd: rawnand: omap2: fix the probe function error path
mtd: rawnand: mxc: fix probe function error path
mtd: rawnand: denali: fix probe function error path
mtd: rawnand: davinci: fix probe function error path
mtd: rawnand: cafe: fix probe function error path
mtd: rawnand: brcmnand: fix probe function error path
mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode
mtd: rawnand: marvell: Fix clock resource by adding a register clock
mtd: ftl: Use DIV_ROUND_UP()
mtd: Fix some function description mismatches in mtdcore.c
mtd: physmap_of: update struct map_info's swap as per map requirement
dt-bindings: mtd-physmap: Add endianness supports
...
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqKKI0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGRNAH/0v3+nuJ0oiHE1Cl
fH89F9Ma17j8oTo28byRPi7X5XJfJAqANhHa209rguvnC27y3ew/l9k93HoxG12i
ttvyKFDQulQbytfJZXw8lhUyYGXVsTpyNaihPe/NtqPdIxNgfrXsUN9EIEtcnuS2
SiAj51jUySDRNR4ST6TOx4ulDm1zLrmA28WHOBNOTvDi4jTQMt1TsngHfF5AySBB
lD4RTRDDwWDWtdMI7euYSq019TiDXCxmwQ94vZjrqmjmSQcl/yCK/JzEV33SZslg
4WqGIllxONvP/UlwxZLaJ+RrslqxNgDVqQKwJdfYhGaWvpgPFtS1s86zW6IgyXny
02jJfD0=
=DLWn
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into mtd/next
Backmerge v4.16-rc2 into mtd/next to resolve a conflict between Linus'
master branch and nand/for-4.17.
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=uvio
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
In core.c, some function descriptions do not match function
definitions. Just fix these mismatches.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
get_sectorsize() was not using the appropriate macro to extract the
ECC sector size from the config cache, which led to buggy ECC when
using 1024 byte sectors.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Reported-by: Olivier Schonken <olivier.schonken@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Olivier Schonken <olivier.schonken@gmail.com>
The core clock field was badly named ->ecc_clk which might lead to some
confusion. Rename it ->core_clk.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Prepare the migration of the lpc32xx_slc driver to use nand_scan() by
cleaning the error path in the probe function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This mode is not used by any existing setup and should not be used
because it overwrites the BBMs. Let's just remove it before someone
starts using it.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The binding documentation is updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Due to missing information in Hardware manual, current
implementation doesn't read ECCSTAT0 and ECCSTAT1 registers
for IFC 2.0.
Add support to read ECCSTAT0 and ECCSTAT1 registers during
ecccheck for IFC 2.0.
Fixes: 656441478e ("mtd: nand: ifc: Fix location of eccstat registers for IFC V1.0")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Number of ECC status registers i.e. (ECCSTATx) has been increased in IFC
version 2.0.0 due to increase in SRAM size. This is causing eccstat
array to over flow.
So, replace eccstat array with u32 variable to make it fail-safe and
independent of number of ECC status registers or SRAM size.
Fixes: bccb06c353 ("mtd: nand: ifc: update bufnum mask for ver >= 2.0.0")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As per the IFC hardware manual, Most significant 2 bytes in
nand_fsr register are the outcome of NAND READ STATUS command.
So status value need to be shifted and aligned as per the nand
framework requirement.
Fixes: 82771882d9 ("NAND Machine support for Integrated Flash Controller")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD users are no longer checking erase_info->state to determine if the
erase operation failed or succeeded. Moreover, mtd_erase_callback() is
now a NOP.
We can safely get rid of all mtd_erase_callback() calls and all
erase_info->state assignments. While at it, get rid of the
erase_info->state field, all MTD_ERASE_XXX definitions and the
mtd_erase_callback() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
---
Changes in v2:
- Address a few coding style issues (reported by Miquel)
- Remove comments that are no longer valid (reported by Miquel)
GPMI driver timings derivation looks very empirical and does not use
the known timings that the core wants to use with the NAND chip, by
using local defined constants that have no special meaning from the
outside world.
Simplify the way all of this is computed and use the NAND core's SDR
timings.
Integrity of the reads/writes has been checked with nandbiterrs, speed
improvements with flash_speed on a Freescale i.MX6 DualLite/Solo SABRE
Automotive Board. Measures are below, variations of less than 150kiB/s
between tests are common and then not significant. Speeds using mode 5
are the same, while speeds using mode 0 are quite improved (+40/50%
from non-optimal computation).
Forcing timings mode 0:
=======================
Before this patch:
------------------
eraseblock write speed is 2298 KiB/s
eraseblock read speed is 3636 KiB/s
page write speed is 2136 KiB/s
page read speed is 3316 KiB/s
2 page write speed is 2199 KiB/s
2 page read speed is 3468 KiB/s
After this patch:
-----------------
eraseblock write speed is 3232 KiB/s
eraseblock read speed is 5663 KiB/s
page write speed is 2915 KiB/s
page read speed is 4904 KiB/s
2 page write speed is 3084 KiB/s
2 page read speed is 5267 KiB/s
Forcing timings mode 5:
=======================
Before this patch:
------------------
eraseblock write speed is 4338 KiB/s
eraseblock read speed is 14883 KiB/s
page write speed is 3786 KiB/s
page read speed is 12800 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
After this patch:
-----------------
eraseblock write speed is 4309 KiB/s
eraseblock read speed is 14712 KiB/s
page write speed is 3764 KiB/s
page read speed is 12673 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Until now the GPMI driver had its own timings logic while the core
already handles that and request the NAND controller drivers to support
the ->setup_data_interface() hook. Implement that hook by reusing the
already existing function. No real glue is necessary between core timing
delays and GPMI registers because the driver already translates the
ONFI timing modes into register values.
Make use of the core's tREA, tRLOH and tRHOH values that allow computing
more precise timings for mode [0-3] and get significantly better values
(+20% with an i.MX6 Sabre Auto board). Otherwise use the existing logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that hold all needed
ONFI parameters, remove the ONFI page from the nand_chip structure by
just allocating it during the identification phase and removing it right
after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that can held
generic parameters, remove the JEDEC page from the nand_chip structure
by just allocating it during the identification phase and removing it
right after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The MX30LF2G18AC chip declares in its parameter page supporting
SET/GET_FEATURES but when it comes to timings, experience shows that it
is not the case.
Unflag this feature for this particular chip in the nand_parameters
structure to avoid unnecessary errors and downturns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If SET/GET_FEATURES is available (from the parameter page), use a
bitmap to declare what feature is actually supported.
Initialize the bitmap in the core to support timing changes (only
feature used by the core), also add support for Micron specific features
used in Micron initialization code (in the init routine).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.
For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
After a nand_reset_data_interface(), both the NAND chip and the NAND
controller use timing mode 0. The previously defined data interface for
this chip has been saved and is supposed to be restored after that.
However, if the saved data interface also refers to timing mode 0, there
is no need to re-apply them again.
Also, as nand_setup_data_interface() uses ->set/get_features(), it could
lead to issues when doing the reset at probe time as the parameter page
is not available yet to know if these functions are supported or not.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Choosing ONFI timings when ->set/get_features() calls are supported
by the NAND chip is a matter of reading the chip's ONFI parameter page
and telling the chip the chosen mode (between all of the supported ones)
with ->set_feature().
Add a check on whether the chip "acked" the timing mode or not.
This can be a problem for NAND chips that do not follow entirely the
ONFI specification. These chips actually support other modes than
"mode 0", but either:
1/ do not update the timing mode register once a timing mode has been
selected.
or
2/ do not support the TIMING_MODE featured and thus do not require users
to change the timing mode at all.
These issues will be addressed in another patch that will add the
feature to overwrite NAND chips features within the parameter page, from
the NAND chip driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
After a ->set_features(TIMINGS), the chip is supposed to be working at a
new speed. In order for all the transactions to be perperly handled, the
NAND controller should also be configured to this same speed. Calling
->setup_data_interface() is not enough and the chip should be
de-asserted/re-asserted through calls to ->select_chip().
Prepare the next change in nand_setup_data_interface() where timings
will be checked after being applied. Because assertions of the CS pin
will be needed from within this function, move the calls to
->select_chip() inside nand_setup_data_interface() for later
consistency.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
All the calls to the chip's hooks ->get/set_features() go through
the core's wrappers nand_get/set_features() that already do the
necessary checks about feature support. Remove these
checks from the mxc's functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Usually, the source of the error when setting/getting features does not
matter (if the controller does not support sending the command or if
the chip does not support the operation).
When it comes to timings, if the controller fails it is an error while
if the chip does not support the operation, it can be silently supposed
that it already works with the maximum supported timings.
Introduce some logic in nand_setup_data_interface() to handle that
difference.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare the fact that some features managed by GET/SET_FEATURES could be
overloaded by vendor code. To handle this logic, use new wrappers
instead of directly call the ->get/set_features() hooks.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
SET/GET FEATURES are flagged ONFI-compliant because of their name. This
is not accurate as non-ONFI NAND chips support it and use it.
Rename the hooks and helpers to remove the "onfi" prefix.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare future work on the ->onfi_get/set_features() hooks by renaming
the core's implementation as 'default' ones.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Files have been moved in the NAND subsystem to reflect the different
flavors of NAND devices.
Raw/Parallel NAND devices have been moved to a "raw" subdirectory to
make the difference with OneNAND and SPI NAND for instance. So adjust
the Kconfig entry to clarify things.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The blackfin architecture is getting removed, so this driver has
become obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
With the move to ->exec_op() the driver should now support ONFI
SET/GET_FEATURES commands.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Now that the driver is using ->exec_op(), remove the old
hooks.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This reworks the driver to make use of ->exec_op() callback. The
command sequencer of the VF610 NFC aligns well with the new ops
interface.
The operations are translated to a NFC command code while filling
the necessary registers. Instead of using the special status and
read ID command codes (which require to read status/ID from
special registers instead of the regular data area) the driver
now now uses the main data buffer for all commands. This
simplifies the driver as no special casing is needed.
For control data (status byte, id bytes and parameter page) the
driver needs to reverse byte order for little endian CPUs since
the controller seems to store the bytes in big endian order in
the data buffer.
The current state seems to pass MTD tests on a Colibri VF61.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
->fail_addr and ->addr can be updated no matter the result of
parent->_erase(), we just need to remove the code doing the same thing
in mtd_erase_callback() to avoid adjusting those fields twice.
Note that this can be done because all MTD users have been converted to
not pass an erase_info->callback() and are thus only taking the
->addr_fail and ->addr fields into account after part_erase() has
returned.
While we're at it, get rid of the erase_info->mtd field which was only
needed to let mtd_erase_callback() get the partition device back.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
This file can not be built independently any more. We would have to
bring in more to resolve mtd_to_nand(mtd)->ecc.size, for example.
It is difficult to notice a breakage since nobody compiles this mode.
It is not worth fixing or maintaining in my opinion. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using pr_<loglevel>() is more concise than printk(KERN_<LOGLEVEL>).
Replace printks having a log level with the appropriate pr_*() macros.
Define pr_fmt() and remove other additional macros from the replaced
printks.
Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
