There is no reason why power channel shouldn't be exported as is done for
voltage, current, temperature and humidity.
Power channel is available on iio ina226 driver.
Sysfs IIO documentation for power attribute added by commit 7c6d5c7ee8
("iio: Documentation: Add missing documentation for power attribute")
is declaring that value is in mili-Watts but hwmon interface is expecting
value in micro-Watts that's why there is a need for mili-Watts to
micro-Watts conversion.
Tested on Xilinx ZCU102 board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/db71f5ae87e4521a2856a1be5544de0b6cede575.1566483741.git.michal.simek@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ipsps1 is an Inspur Power System power supply unit
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the driver to monitor Inspur Power System power supplies
with hwmon over pmbus.
This driver adds sysfs attributes for additional power supply data,
including vendor, model, part_number, serial number,
firmware revision, hardware revision, and psu mode(active/standby).
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190819091509.29276-1-wangzqbj@inspur.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ltc2990 will now use device_property_read_u32_array() instead of
of_property_read_u32_array() - allowing the use of software nodes
via fwnode_create_software_node().
This allows code using i2c_new_device() to specify a default
measurement mode for the LTC2990 via fwnode_create_software_node().
Signed-off-by: Max Staudt <max@enpas.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20190819121618.16557-2-max@enpas.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* Create two separate functions to write into hwmon_temp and hwmon_chip.
* Call the functions from lm75_write.
* Make hwm_chip writable if the chip supports more than one sample time.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-5-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new fields are included to prepare the driver for next patch. The
fields are:
* *resolutions: Stores all the supported resolutions by the device.
* num_sample_times: Stores the number of possible sample times.
* *sample_times: Stores all the possible sample times to be set.
* sample_set_masks: The set_masks for the possible sample times
* sample_clr_mask: Clear mask to set the default sample time.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-4-iker.perez@codethink.co.uk
[groeck: Minor structure documentation fixes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Wrap the existing code to write configurations into registers in
a function.
Added error handling to the function.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-3-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
* Add to lm75_data kind field to store the kind of device the driver is
working with.
* Add an structure to store the configuration parameters of all the
supported devices.
* Delete resolution_limits from lm75_data and include them in the structure
described above.
* Add a pointer to the configuration parameters structure to be used as a
reference to obtain the parameters.
* Delete switch-case approach to get the device configuration parameters.
* The structure is cleaner and easier to maintain.
Signed-off-by: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk>
Link: https://lore.kernel.org/r/20190808080246.8371-2-iker.perez@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT-7904D also supports reading of channel limitation registers as well
as SMI status registers for fan, voltage and temperature monitoring.
It also supports reading the temperature sensor type (thermal diode,
thermistor, AMD SB-TSI or Intel PECI).
Add the following sysfs nodes:
-fan[1-*]_min
-fan[1-*]_alarm
-in[1-*]_min
-in[1-*]_max
-in[1-*]_alarm
-temp[1-*]_max
-temp[1-*]_max_hyst
-temp[1-*]_emergency
-temp[1-*]_emergency_hyst
-temp[1-*]_alarm
-temp[1-*]_type
Signed-off-by: Amy Shih <amy.shih@advantech.com.tw>
Link: https://lore.kernel.org/r/20190807013842.24451-1-Amy.Shih@advantech.com.tw
[groeck: Clarified description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I have been using SENSORS_W83795_FANCTRL for several years and never
had any problem. When the driver was added, I had not tested that
part of the driver yet so I wanted to be super cautious, but time has
shown that it works just fine.
In the long run I even believe that we should drop the option and
enable the feature unconditionally. It doesn't do anything until the
user explicitly starts twiddling with sysfs attributes anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20190806102123.3118bcc5@endymion
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[groeck: Dropped jz4740-hwmon.c (driver is being removed)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
At boot time, the acpi_power_meter driver logs the following error level
message: "Ignoring unsafe software power cap". Having read about it from
a few sources, it seems that the error message can be quite misleading.
While the message can imply that Linux is ignoring the fact that the
system is operating in potentially dangerous conditions, the truth is
the driver found an ACPI_PMC object that supports software power
capping. The driver simply decides not to use it, perhaps because it
doesn't support the object.
The best solution is probably changing the log level from error to warning.
All sources I have found, regarding the error, have downplayed its
significance. There is not much of a reason for it to be on error level,
while causing potential confusions or misinterpretations.
Signed-off-by: Wang Shenran <shenran268@gmail.com>
Link: https://lore.kernel.org/r/20190724080110.6952-1-shenran268@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon_device_register() is a deprecated function and produces a warning.
Converting the driver to use the hwmon_device_register_with_groups()
instead.
Signed-off-by: Grant McEwan <grant.mcewan@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20190721225530.28799-2-grant.mcewan@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It would seem like model 70h is behaving in the same way as model 30h,
so let's just add the new F3 PCI ID to the list of compatible devices.
Unlike previous Ryzen/Threadripper, Ryzen gen 3 processors do not need
temperature offsets anymore. This has been reported in the press and
verified on my Ryzen 3700X by checking that the idle temperature
reported by k10temp is matching the temperature reported by the
firmware.
Vicki Pfau sent an identical patch after I checked that no-one had
written this patch. I would have been happy about dropping my patch but
unlike for his patch series, I had already Cc:ed the x86 people and
they already reviewed the changes. Since Vicki has not answered to
any email after his initial series, let's assume she is on vacation
and let's avoid duplication of reviews from the maintainers and merge
my series. To acknowledge Vicki's anteriority, I added her S-o-b to
the patch.
v2, suggested by Guenter Roeck and Brian Woods:
- rename from 71h to 70h
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Tested-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: "Woods, Brian" <Brian.Woods@amd.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20190722174653.2391-1-marcel.p.bocu@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The AMD Ryzen gen 3 processors came with a different PCI IDs for the
function 3 & 4 which are used to access the SMN interface. The root
PCI address however remained at the same address as the model 30h.
Adding the F3/F4 PCI IDs respectively to the misc and link ids appear
to be sufficient for k10temp, so let's add them and follow up on the
patch if other functions need more tweaking.
Vicki Pfau sent an identical patch after I checked that no-one had
written this patch. I would have been happy about dropping my patch but
unlike for his patch series, I had already Cc:ed the x86 people and
they already reviewed the changes. Since Vicki has not answered to
any email after his initial series, let's assume she is on vacation
and let's avoid duplication of reviews from the maintainers and merge
my series. To acknowledge Vicki's anteriority, I added her S-o-b to
the patch.
v2, suggested by Guenter Roeck and Brian Woods:
- rename from 71h to 70h
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Tested-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Brian Woods <brian.woods@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci_ids.h
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: "Woods, Brian" <Brian.Woods@amd.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20190722174510.2179-1-marcel.p.bocu@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Removes:
- hwmon_dev from k8temp_data struct, as that is now passed
to callbacks, anyway.
- other k8temp_data struct fields, too.
- k8temp_update_device()
Also reduces binary size:
text data bss dec hex filename
4139 1448 0 5587 15d3 drivers/hwmon/k8temp.ko.bak
3103 1220 0 4323 10e3 drivers/hwmon/k8temp.ko
Signed-off-by: Robert Karszniewicz <avoidr@firemail.cc>
Signed-off-by: Robert Karszniewicz <avoidr@riseup.net>
Link: https://lore.kernel.org/r/20190721120051.28064-1-avoidr@riseup.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is a typo in MAX37185_NUM_FAN_PAGES. To be consistent, it should be
MAX31785_NUM_FAN_PAGES (1 and 7 switched).
At line 24, we already have:
#define MAX31785_NR_FAN_PAGES 6
and MAX37185_NUM_FAN_PAGES seems to be unused.
It is likely that it is only a typo and/or a left-over.
So, axe it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20190721101553.20911-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use of 'unsigned int' instead of bare use of 'unsigned'. Fix this for
edac_mc*, ghes and the i5100 driver as reported by checkpatch.pl.
While at it, struct member dev_ch_attribute->channel is always used as
unsigned int. Change type to unsigned int to avoid type casts.
[ bp: Massage. ]
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190902123216.9809-2-rrichter@marvell.com
Turns out the commit 3a0681c744 ("mmc: core: do not retry CMD6 in
__mmc_switch()") breaks initialization of a Toshiba THGBMNG5 eMMC card,
when using the meson-gx-mmc.c driver on a custom board based on Amlogic
A113D.
The CMD6 that switches the card into HS200 mode is then one that fails and
according to the below printed messages from the log:
[ 1.648951] mmc0: mmc_select_hs200 failed, error -84
[ 1.648988] mmc0: error -84 whilst initialising MMC card
After some analyze, it turns out that adding a delay of ~5ms inside
mmc_select_bus_width() but after mmc_compare_ext_csds() has been executed,
also fixes the problem. Adding yet some more debug code, trying to figure
out if potentially the card could be in a busy state, both by using CMD13
and ->card_busy() ops concluded that this was not the case.
Therefore, let's simply revert the commit that dropped support for retrying
of CMD6, as this also fixes the problem.
Fixes: 3a0681c744 ("mmc: core: do not retry CMD6 in __mmc_switch()")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Kaisrlik <ja.kaisrlik@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
`dev` (struct rsi_91x_usbdev *) field of adapter
(struct rsi_91x_usbdev *) is allocated and initialized in
`rsi_init_usb_interface`. If any error is detected in information
read from the device side, `rsi_init_usb_interface` will be
freed. However, in the higher level error handling code in
`rsi_probe`, if error is detected, `rsi_91x_deinit` is called
again, in which `dev` will be freed again, resulting double free.
This patch fixes the double free by removing the free operation on
`dev` in `rsi_init_usb_interface`, because `rsi_91x_deinit` is also
used in `rsi_disconnect`, in that code path, the `dev` field is not
(and thus needs to be) freed.
This bug was found in v4.19, but is also present in the latest version
of kernel. Fixes CVE-2019-15504.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 9ad3b55654.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b55654 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Cc: <stable@vger.kernel.org> # v5.1+
Reported-and-tested-by: Sergey Maranchuk <slav0nic0@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After looking at code I realized that my previous fix
9584412438 ("rt2x00: clear IV's on start to fix AP mode regression")
was incomplete. We can still have wrong IV's after re-keyring.
To fix that, clear up IV's also on key removal.
Fixes: 710e6cc159 ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
tested-by: Emil Karlson <jekarl@iki.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost. Assign directly to iwl_trans->cfg instead.
Fixes: 5a8c31aa63 ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_update_vs_ie(),mwifiex_set_uap_rates() and
mwifiex_set_wmm_params() call memcpy() without checking
the destination size.Since the source is given from
user-space, this may trigger a heap buffer overflow.
Fix them by putting the length check before performing memcpy().
This fix addresses CVE-2019-14814,CVE-2019-14815,CVE-2019-14816.
Signed-off-by: Wen Huang <huangwenabc@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.comg>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MT7630E hardware does support 5GHz, but we do not properly configure phy
for 5GHz channels. Scanning at this band not only do not show any APs
but also can hang the firmware.
Since vendor reference driver do not support 5GHz we don't know how
properly configure 5GHz channels. So disable this band for MT7630E .
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
I can observe firmware hangs on MT7630E on station mode: tx stop
functioning after minor activity (rx keep working) and on module
unload device fail to stop with messages:
[ 5446.141413] mt76x0e 0000:06:00.0: TX DMA did not stop
[ 5449.176764] mt76x0e 0000:06:00.0: TX DMA did not stop
Loading module again results in failure to associate with AP.
Only machine power off / power on cycle can make device work again.
It's unclear why commit 41634aa8d6 causes the problem, but it is
related to HW encryption. Since issue is a firmware hang, that is super
hard to debug, just disable HW encryption as fix for the issue.
Fixes: 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Global pages support is removed from VT-d spec 3.0. Since global pages G
flag only affects first-level paging structures and because DMA request
with PASID are only supported by VT-d spec. 3.0 and onward, we can
safely remove global pages support.
For kernel shared virtual address IOTLB invalidation, PASID
granularity and page selective within PASID will be used. There is
no global granularity supported. Without this fix, IOTLB invalidation
will cause invalid descriptor error in the queued invalidation (QI)
interface.
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Reported-by: Sanjay K Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
do_sched_cfs_period_timer() will refill cfs_b runtime and call
distribute_cfs_runtime to unthrottle cfs_rq, sometimes cfs_b->runtime
will allocate all quota to one cfs_rq incorrectly, then other cfs_rqs
attached to this cfs_b can't get runtime and will be throttled.
We find that one throttled cfs_rq has non-negative
cfs_rq->runtime_remaining and cause an unexpetced cast from s64 to u64
in snippet:
distribute_cfs_runtime() {
runtime = -cfs_rq->runtime_remaining + 1;
}
The runtime here will change to a large number and consume all
cfs_b->runtime in this cfs_b period.
According to Ben Segall, the throttled cfs_rq can have
account_cfs_rq_runtime called on it because it is throttled before
idle_balance, and the idle_balance calls update_rq_clock to add time
that is accounted to the task.
This commit prevents cfs_rq to be assgined new runtime if it has been
throttled until that distribute_cfs_runtime is called.
Signed-off-by: Liangyan <liangyan.peng@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: shanpeic@linux.alibaba.com
Cc: stable@vger.kernel.org
Cc: xlpang@linux.alibaba.com
Fixes: d3d9dc3302 ("sched: Throttle entities exceeding their allowed bandwidth")
Link: https://lkml.kernel.org/r/20190826121633.6538-1-liangyan.peng@linux.alibaba.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Original pin node values of ASUS UX431FL with ALC294:
0x12 0xb7a60140
0x13 0x40000000
0x14 0x90170110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x90170111
0x18 0x411111f0
0x19 0x411111f0
0x1a 0x411111f0
0x1b 0x411111f0
0x1d 0x4066852d
0x1e 0x411111f0
0x1f 0x411111f0
0x21 0x04211020
1. Has duplicated internal speakers (0x14 & 0x17) which makes the output
route become confused. So, the output volume cannot be changed by
setting.
2. Misses the headset mic pin node.
This patch disables the confusing speaker (NID 0x14) and enables the
headset mic (NID 0x19).
Link: https://lore.kernel.org/r/20190902100054.6941-1-jian-hong@endlessm.com
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The socket assignment is wrong, see skb_orphan():
When skb->destructor callback is not set, but skb->sk is set, this hits BUG().
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1651813
Fixes: 554ced0a6e ("netfilter: nf_tables: add support for native socket matching")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A kernel panic can happen if a host has disabled IPv6 on boot and have to
process guest packets (coming from a bridge) using it's ip6tables.
IPv6 packets need to be dropped if the IPv6 module is not loaded, and the
host ip6tables will be used.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Refcounted, hangs of configfs_dirent, created by operations that add
fragments to configfs tree (mkdir and configfs_register_{subsystem,group}).
Will be used in the next commit to provide exclusion between fragment
removal and ->show/->store calls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
revert cc57c07343 "configfs: fix registered group removal"
It was an attempt to handle something that fundamentally doesn't
work - configfs_register_group() should never be done in a part
of tree that can be rmdir'ed. And in mainline it never had been,
so let's not borrow trouble; the fix was racy anyway, it would take
a lot more to make that work and desired semantics is not clear.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
simplifies the ->read()/->write()/->release() instances nicely
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In function sun8i_dwmac_set_syscon(), local variable "val" could
be uninitialized if function regmap_field_read() returns -EINVAL.
However, it will be used directly in the if statement, which
is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the 'start' parameter is >= 0xFF000000 on 32-bit
systems, or >= 0xFFFFFFFF'FF000000 on 64-bit systems,
fill_gva_list() gets into an infinite loop.
With such inputs, 'cur' overflows after adding HV_TLB_FLUSH_UNIT
and always compares as less than end. Memory is filled with
guest virtual addresses until the system crashes.
Fix this by never incrementing 'cur' to be larger than 'end'.
Reported-by: Jong Hyun Park <park.jonghyun@yonsei.ac.kr>
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 2ffd9e33ce ("x86/hyper-v: Use hypercall for remote TLB flush")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We want to throw out the attrbute if it refers to the mounted on fileid,
and not the real fileid. However we do not want to block cache consistency
updates from NFSv4 writes.
Reported-by: Murphy Zhou <jencce.kernel@gmail.com>
Fixes: 7e10cc25bf ("NFS: Don't refresh attributes with mounted-on-file...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
