It is not actually implemented.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To silent "make htmldocs" warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_link_dev_addr sorts newly added addresses by scope in
ifp->addr_list. Smaller scope addresses are added to the tail of the
list. Use this fact to iterate in reverse over addr_list and break out
as soon as a higher scoped one showes up, so we can spare some cycles
on machines with lot's of addresses.
The ordering of the addresses is not relevant and we are more likely to
get the eui64 generated address with this change anyway.
Suggested-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently don't report IPV6_RECVPKTINFO in cmsg access ancillary data
for IPv4 datagrams on IPv6 sockets.
This patch splits the ip6_datagram_recv_ctl into two functions, one
which handles both protocol families, AF_INET and AF_INET6, while the
ip6_datagram_recv_specific_ctl only handles IPv6 cmsg data.
ip6_datagram_recv_*_ctl never reported back any errors, so we can make
them return void. Also provide a helper for protocols which don't offer dual
personality to further use ip6_datagram_recv_ctl, which is exported to
modules.
I needed to shuffle the code for ping around a bit to make it easier to
implement dual personality for ping ipv6 sockets in future.
Reported-by: Gert Doering <gert@space.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some magic numbers which describe states of 4-state model
loss generator with enumerate.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of IPV6_FL_F_REFLECT, there is no guarantee of
flow label unicity. This patch introduces a new sysctl to protect the old
behaviour, enable by default.
Changelog of V3:
* rename ip6_flowlabel_consistency to flowlabel_consistency
* use net_info_ratelimited()
* checkpatch cleanups
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This information is already available via IPV6_FLOWINFO
of IPV6_2292PKTOPTIONS, and them a filtering to get the flow label
information. But it is probably logical and easier for users to add this
here, and to control both sent/received flow label values with the
IPV6_FLOWLABEL_MGR option.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this option, the socket will reply with the flow label value read
on received packets.
The goal is to have a connection with the same flow label in both
direction of the communication.
Changelog of V4:
* Do not erase the flow label on the listening socket. Use pktopts to
store the received value
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some dev_kfree_skb() with kfree_skb() calls when
we drop one skb, this might help bug tracking.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch to f3d3342602 ("net: rework recvmsg
handler msg_name and msg_namelen logic").
DECLARE_SOCKADDR validates that the structure we use for writing the
name information to is not larger than the buffer which is reserved
for msg->msg_name (which is 128 bytes). Also use DECLARE_SOCKADDR
consistently in sendmsg code paths.
Signed-off-by: Steffen Hurrle <steffen@hurrle.net>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For user space packet capturing libraries such as libpcap, there's
currently only one way to check which BPF extensions are supported
by the kernel, that is, commit aa1113d9f8 ("net: filter: return
-EINVAL if BPF_S_ANC* operation is not supported"). For querying all
extensions at once this might be rather inconvenient.
Therefore, this patch introduces a new option which can be used as
an argument for getsockopt(), and allows one to obtain information
about which BPF extensions are supported by the current kernel.
As David Miller suggests, we do not need to define any bits right
now and status quo can just return 0 in order to state that this
versions supports SKF_AD_PROTOCOL up to SKF_AD_PAY_OFFSET. Later
additions to BPF extensions need to add their bits to the
bpf_tell_extensions() function, as documented in the comment.
Signed-off-by: Michal Sekletar <msekleta@redhat.com>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's now built as a separate utility module, and enabling BT selects
that module in Kconfig. This fixes:
net/ieee802154/built-in.o:(___ksymtab_gpl+lowpan_process_data+0x0): multiple definition of `__ksymtab_lowpan_process_data'
net/bluetooth/built-in.o:(___ksymtab_gpl+lowpan_process_data+0x0): first defined here
net/ieee802154/built-in.o:(___ksymtab_gpl+lowpan_header_compress+0x0): multiple definition of `__ksymtab_lowpan_header_compress'
net/bluetooth/built-in.o:(___ksymtab_gpl+lowpan_header_compress+0x0): first defined here
net/ieee802154/built-in.o: In function `lowpan_header_compress':
net/ieee802154/6lowpan_iphc.c:606: multiple definition of `lowpan_header_compress'
net/bluetooth/built-in.o:/home/swarren/shared/git_wa/kernel/kernel.git/net/bluetooth/../ieee802154/6lowpan_iphc.c:606: first defined here
net/ieee802154/built-in.o: In function `lowpan_process_data':
net/ieee802154/6lowpan_iphc.c:344: multiple definition of `lowpan_process_data'
net/bluetooth/built-in.o:/home/swarren/shared/git_wa/kernel/kernel.git/net/bluetooth/../ieee802154/6lowpan_iphc.c:344: first defined here
make[1]: *** [net/built-in.o] Error 1
(this change probably simply wasn't "git add"d to a53d34c346)
Fixes: a53d34c346 ("net: move 6lowpan compression code to separate module")
Fixes: 18722c2470 ("Bluetooth: Enable 6LoWPAN support for BT LE devices")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link is IFF_SLAVE, extend link dev netlink attributes to include
slave attributes with new IFLA_SLAVE nest. Add netlink notification
(RTM_NEWLINK) when slave status changes from backup to active, or
visa-versa.
Adds new ndo_get_slave op to net_device_ops to fill skb with IFLA_SLAVE
attributes. Currently only used by bonding driver, but could be
used by other aggregating devices with slaves.
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch :
1) Remove a dst leak if DST_NOCACHE was set on dst
Fix this by holding a reference only if dst really cached.
2) Remove a lockdep warning in __tunnel_dst_set()
This was reported by Cong Wang.
3) Remove usage of a spinlock where xchg() is enough
4) Remove some spurious inline keywords.
Let compiler decide for us.
Fixes: 7d442fab0a ("ipv4: Cache dst in tunnels")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RFC 3810 defines two type of messages for multicast
listeners. The "Current State Report" message, as the name
implies, refreshes the *current* state to the querier.
Since the querier sends Query messages periodically, there
is no need to retransmit the report.
On the other hand, any change should be reported immediately
using "State Change Report" messages. Since it's an event
triggered by a change and that it can be affected by packet
loss, the rfc states it should be retransmitted [RobVar] times
to make sure routers will receive timely.
Currently, we are sending "Current State Reports" after
DAD is completed. Before that, we send messages using
unspecified address (::) which should be silently discarded
by routers.
This patch changes to send "State Change Report" messages
after DAD is completed fixing the behavior to be RFC compliant
and also to pass TAHI IPv6 testsuite.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1ec047eb47 ("ipv6: introduce per-interface counter for
dad-completed ipv6 addresses") I build the detection of the first
operational link-local address much to complex. Additionally this code
now has a race condition.
Replace it with a much simpler variant, which just scans the address
list when duplicate address detection completes, to check if this is
the first valid link local address and send RS and MLD reports then.
Fixes: 1ec047eb47 ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses")
Reported-by: Jiri Pirko <jiri@resnulli.us>
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the tcp-metrics is an RCU-list, it may be that two
soft-interrupts are inside __tcp_get_metrics() for the same
destination-IP at the same time. If this destination-IP is not yet part of
the tcp-metrics, both soft-interrupts will end up in tcpm_new and create
a new entry for this IP.
So, we will have two tcp-metrics with the same destination-IP in the list.
This patch checks twice __tcp_get_metrics(). First without holding the
lock, then while holding the lock. The second one is there to confirm
that the entry has not been added by another soft-irq while waiting for
the spin-lock.
Fixes: 51c5d0c4b1 (tcp: Maintain dynamic metrics in local cache.)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is following the commit b903d324be (ipv6: tcp: fix TCLASS
value in ACK messages sent from TIME_WAIT).
For the same reason than tclass, we have to store the flow label in the
inet_timewait_sock to provide consistency of flow label on the last ACK.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit ae4b46e9d "net: rds: use this_cpu_* per-cpu helper" broke per-cpu
handling for rds. chpfirst is the result of __this_cpu_read(), so it is
an absolute pointer and not __percpu. Therefore, __this_cpu_write()
should not operate on chpfirst, but rather on cache->percpu->first, just
like __this_cpu_read() did before.
Cc: <stable@vger.kernel.org> # 3.8+
Signed-off-byd Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing support for netdevice receive queue sysfs attributes to
permit a device-specific attribute group. Initial use case for this
support will be to allow the virtio-net device to export per-receive
queue mergeable receive buffer size.
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_page_frag_refill currently permits only order-0 page allocs
unless GFP_WAIT is used. Change skb_page_frag_refill to attempt
higher-order page allocations whether or not GFP_WAIT is used. If
memory cannot be allocated, the allocator will fall back to
successively smaller page allocs (down to order-0 page allocs).
This change brings skb_page_frag_refill in line with the existing
page allocation strategy employed by netdev_alloc_frag, which attempts
higher-order page allocations whether or not GFP_WAIT is set, falling
back to successively lower-order page allocations on failure. Part
of migration of virtio-net to per-receive queue page frag allocators.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error code was not set if change indev fail, so the error
condition wasn't reflected in the return value. Fix to return a
negative error code from this error handling case instead of 0.
Fixes: 2519a602c2 ('net_sched: optimize tcf_match_indev()')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Standardize the behaviour of waiting for events in TIPC recvmsg()
so that all variables of socket or port structures are protected
within socket lock, allowing the process of calling recvmsg() to
be woken up at appropriate time.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Standardize the behaviour of waiting for events in TIPC send_packet()
so that all variables of socket or port structures are protected within
socket lock, allowing the process of calling sendmsg() to be woken up
at appropriate time.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing the behaviour of how to wait for events in TIPC sendmsg()
with other stacks, the TIPC implementation might be perceived as
different, and sometimes even incorrect. For instance, sk_sleep()
and tport->congested variables associated with socket are exposed
without socket lock protection while wait_event_interruptible_timeout()
accesses them. So standardizing it with similar implementation
in other stacks can help us correct these errors which the process
of calling sendmsg() cannot be woken up event if an expected event
arrive at socket or improperly woken up although the wake condition
doesn't match.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing the behaviour of how to wait for events in TIPC accept()
with other stacks, the TIPC implementation might be perceived as
different, and sometimes even incorrect. As sk_sleep() and
sk->sk_receive_queue variables associated with socket are not
protected by socket lock, the process of calling accept() may be
woken up improperly or sometimes cannot be woken up at all. After
standardizing it with inet_csk_wait_for_connect routine, we can
get benefits including: avoiding 'thundering herd' phenomenon,
adding a timeout mechanism for accept(), coping with a pending
signal, and having sk_sleep() and sk->sk_receive_queue being
always protected within socket lock scope and so on.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comparing the behaviour of how to wait for events in TIPC connect()
with other stacks, the TIPC implementation might be perceived as
different, and sometimes even incorrect. For instance, as both
sock->state and sk_sleep() are directly fed to
wait_event_interruptible_timeout() as its arguments, and socket lock
has to be released before we call wait_event_interruptible_timeout(),
the two variables associated with socket are exposed out of socket
lock protection, thereby probably getting stale values so that the
process of calling connect() cannot be woken up exactly even if
correct event arrives or it is woken up improperly even if the wake
condition is not satisfied in practice. Therefore, standardizing its
behaviour with sk_stream_wait_connect routine can avoid these risks.
Additionally the implementation of connect routine is simplified as a
whole, allowing it to return correct values in all different cases.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When go the right path, the status is 0, no need to assign it again.
So just remove the assignment.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcf_register_action() we check either ->type or ->kind to see if
there is an existing action registered, but ipt action registers two
actions with same type but different kinds. They should have different
types too.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- properly compute the batman-adv header overhead. Such
result is later used to initialize the hard_header_len
member of the soft-interface netdev object
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJS1xUQAAoJEEKTMo6mOh1VStwP/RsjepUZEgjIXs/SrKC0Pkdk
UCnznIyn8b7sLIQokimNESDxADbTphyIBjMZC2XI87udVIRHD3v1NlHWRUzWYvqq
KvYqxuQTfbRnHPwzWiuOzQb9tGJxF+cG4CX8E4ydKqm8LmrNgMX+hL3gq50t5FHU
jtFOiTcqjrZTPcXsdtOyoH9eYDv+9TTqgeetCF4iOZ7G+W/3d4h/EGAaWiCmSjvP
4vdxRFokCdr0OkU/a790SbtHNMWcjCxFCtRSoK9cZFrRjCE+ersOg1g0vWA100Vi
O0yRkZWqODnTu12skhcA2aojFENiT9CFFvZENMpfUxJKnSortFebpKXo+vyW19gC
H6uYR1/KLk00pFOzuKu27hQBvARiKwwkuubeSNthas9jadDSO5ZgZGrDeE4U3GNZ
KIkHunf2HVS2zpylRdnb9A9B/mkO+iW5y6rVtDdXTkrzyhmqTpJPeJqi8j1S10Zl
oyoJIpS+wN7Bslf3fo0f8Pag7cXT28GD4/iPmCkJDpc1GGz7A/HJF/Vpx06L8BWB
pl9TFkxZutBOpCjsFCJ+DvRnmgjolGVqyyyDhizeBVrKMvDW/oJ1PHR6Tx5S3S35
QG3ZNmWIaiZ73bJxzJAY5KxNoehGbPzITEBdTlpo2AMuP1+XFadDF+lquqmeAJSQ
TAI0Paz0VP/RRXxhksKZ
=opzN
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included change:
- properly compute the batman-adv header overhead. Such
result is later used to initialize the hard_header_len
member of the soft-interface netdev object
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a device changes its mtu, first the change happens (invloving
all the side effects), and after that the NETDEV_CHANGEMTU is sent so that
other devices can catch up with the new mtu. However, if they return
NOTIFY_BAD, then the change is reverted and error returned.
This is a really long and costy operation (sometimes). To fix this, add
NETDEV_PRECHANGEMTU notification which is called prior to any change
actually happening, and if any callee returns NOTIFY_BAD - the change is
aborted. This way we're skipping all the playing with apply/revert the mtu.
CC: "David S. Miller" <davem@davemloft.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing a gro_list for a packet, first check the rxhash of
the incoming skb against that of the skb's in the list. This should be
a very strong inidicator of whether the flow is going to be matched,
and potentially allows a lot of other checks to be short circuited.
Use skb_hash_raw so that we don't force the hash to be calculated.
Tested by running netperf 200 TCP_STREAMs between two machines with
GRO, HW rxhash, and 1G. Saw no performance degration, slight reduction
of time in dev_gro_receive.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PF_PACKET's packet mmap(), we can avoid using one atomic_inc()
and one atomic_dec() call in skb destructor and use a percpu
reference count instead in order to determine if packets are
still pending to be sent out. Micro-benchmark with [1] that has
been slightly modified (that is, protcol = 0 in socket(2) and
bind(2)), example on a rather crappy testing machine; I expect
it to scale and have even better results on bigger machines:
./packet_mm_tx -s7000 -m7200 -z700000 em1, avg over 2500 runs:
With patch: 4,022,015 cyc
Without patch: 4,812,994 cyc
time ./packet_mm_tx -s64 -c10000000 em1 > /dev/null, stable:
With patch:
real 1m32.241s
user 0m0.287s
sys 1m29.316s
Without patch:
real 1m38.386s
user 0m0.265s
sys 1m35.572s
In function tpacket_snd(), it is okay to use packet_read_pending()
since in fast-path we short-circuit the condition already with
ph != NULL, since we have next frames to process. In case we have
MSG_DONTWAIT, we also do not execute this path as need_wait is
false here anyway, and in case of _no_ MSG_DONTWAIT flag, it is
okay to call a packet_read_pending(), because when we ever reach
that path, we're done processing outgoing frames anyway and only
look if there are skbs still outstanding to be orphaned. We can
stay lockless in this percpu counter since it's acceptable when we
reach this path for the sum to be imprecise first, but we'll level
out at 0 after all pending frames have reached the skb destructor
eventually through tx reclaim. When people pin a tx process to
particular CPUs, we expect overflows to happen in the reference
counter as on one CPU we expect heavy increase; and distributed
through ksoftirqd on all CPUs a decrease, for example. As
David Laight points out, since the C language doesn't define the
result of signed int overflow (i.e. rather than wrap, it is
allowed to saturate as a possible outcome), we have to use
unsigned int as reference count. The sum over all CPUs when tx
is complete will result in 0 again.
The BUG_ON() in tpacket_destruct_skb() we can remove as well. It
can _only_ be set from inside tpacket_snd() path and we made sure
to increase tx_ring.pending in any case before we called po->xmit(skb).
So testing for tx_ring.pending == 0 is not too useful. Instead, it
would rather have been useful to test if lower layers didn't orphan
the skb so that we're missing ring slots being put back to
TP_STATUS_AVAILABLE. But such a bug will be caught in user space
already as we end up realizing that we do not have any
TP_STATUS_AVAILABLE slots left anymore. Therefore, we're all set.
Btw, in case of RX_RING path, we do not make use of the pending
member, therefore we also don't need to use up any percpu memory
here. Also note that __alloc_percpu() already returns a zero-filled
percpu area, so initialization is done already.
[1] http://wiki.ipxwarzone.com/index.php5?title=Linux_packet_mmap
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tpacket_snd(), when we've discovered a first frame that is
not in status TP_STATUS_SEND_REQUEST, and return a NULL buffer,
we exit the send routine in case of MSG_DONTWAIT, since we've
finished traversing the mmaped send ring buffer and don't care
about pending frames.
While doing so, we still unconditionally call an expensive
schedule() in the packet_current_frame() "error" path, which
is unnecessary in this case since it's enough to just quit
the function.
Also, in case MSG_DONTWAIT is not set, we should rather test
for need_resched() first and do schedule() only if necessary
since meanwhile pending frames could already have finished
processing and called skb destructor.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most people acquire PF_PACKET sockets with a protocol argument in
the socket call, e.g. libpcap does so with htons(ETH_P_ALL) for
all its sockets. Most likely, at some point in time a subsequent
bind() call will follow, e.g. in libpcap with ...
memset(&sll, 0, sizeof(sll));
sll.sll_family = AF_PACKET;
sll.sll_ifindex = ifindex;
sll.sll_protocol = htons(ETH_P_ALL);
... as arguments. What happens in the kernel is that already
in socket() syscall, we install a proto hook via register_prot_hook()
if our protocol argument is != 0. Yet, in bind() we're almost
doing the same work by doing a unregister_prot_hook() with an
expensive synchronize_net() call in case during socket() the proto
was != 0, plus follow-up register_prot_hook() with a bound device
to it this time, in order to limit traffic we get.
In the case when the protocol and user supplied device index (== 0)
does not change from socket() to bind(), we can spare us doing
the same work twice. Similarly for re-binding to the same device
and protocol. For these scenarios, we can decrease create/bind
latency from ~7447us (sock-bind-2 case) to ~89us (sock-bind-1 case)
with this patch.
Alternatively, for the first case, if people care, they should
simply create their sockets with proto == 0 argument and define
the protocol during bind() as this saves a call to synchronize_net()
as well (sock-bind-3 case).
In all other cases, we're tied to user space behaviour we must not
change, also since a bind() is not strictly required. Thus, we need
the synchronize_net() to make sure no asynchronous packet processing
paths still refer to the previous elements of po->prot_hook.
In case of mmap()ed sockets, the workflow that includes bind() is
socket() -> setsockopt(<ring>) -> bind(). In that case, a pair of
{__unregister, register}_prot_hook is being called from setsockopt()
in order to install the new protocol receive handler. Thus, when
we call bind and can skip a re-hook, we have already previously
installed the new handler. For fanout, this is handled different
entirely, so we should be good.
Timings on an i7-3520M machine:
* sock-bind-1: 89 us
* sock-bind-2: 7447 us
* sock-bind-3: 75 us
sock-bind-1:
socket(PF_PACKET, SOCK_RAW, htons(ETH_P_IP)) = 3
bind(3, {sa_family=AF_PACKET, proto=htons(ETH_P_IP), if=all(0),
pkttype=PACKET_HOST, addr(0)={0, }, 20) = 0
sock-bind-2:
socket(PF_PACKET, SOCK_RAW, htons(ETH_P_IP)) = 3
bind(3, {sa_family=AF_PACKET, proto=htons(ETH_P_IP), if=lo(1),
pkttype=PACKET_HOST, addr(0)={0, }, 20) = 0
sock-bind-3:
socket(PF_PACKET, SOCK_RAW, 0) = 3
bind(3, {sa_family=AF_PACKET, proto=htons(ETH_P_IP), if=lo(1),
pkttype=PACKET_HOST, addr(0)={0, }, 20) = 0
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit 438e38fadc
("gre_offload: statically build GRE offloading support") added
new module_init/module_exit calls to the gre_offload.c file.
The file is obj-y and can't be anything other than built-in.
Currently it can never be built modular, so using module_init
as an alias for __initcall can be somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing. We also make the inclusion explicit.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
As for the module_exit, rather than replace it with __exitcall,
we simply remove it, since it appears only UML does anything
with those, and even for UML, there is no relevant cleanup
to be done here.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_type_trans() can read uninitialized memory as drivers
do not necessarily pull more than 14 bytes in skb->head before
calling it.
As David suggested, we can use skb_header_pointer() to
fix this without breaking some drivers that might not expect
eth_type_trans() pulling 2 additional bytes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
This small batch contains several Netfilter fixes for your net-next
tree, more specifically:
* Fix compilation warning in nft_ct in NF_CONNTRACK_MARK is not set,
from Kristian Evensen.
* Add dependency to IPV6 for NF_TABLES_INET. This one has been reported
by the several robots that are testing .config combinations, from Paul
Gortmaker.
* Fix default base chain policy setting in nf_tables, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When ndo_neigh_setup is called, the bitfield used by NEIGH_VAR_SET is
not initialized yet. This might cause confusion for the people who use
NEIGH_VAR_SET in ndo_neigh_setup. So rather introduce NEIGH_VAR_INIT for
usage in ndo_neigh_setup.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
At first Jakub Zawadzki noticed that some divisions by reciprocal_divide
were not correct. (off by one in some cases)
http://www.wireshark.org/~darkjames/reciprocal-buggy.c
He could also show this with BPF:
http://www.wireshark.org/~darkjames/set-and-dump-filter-k-bug.c
The reciprocal divide in linux kernel is not generic enough,
lets remove its use in BPF, as it is not worth the pain with
current cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Daniel Borkmann <dxchgb@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the deletion/update of prefix routes when removing an
address. Now also consider IFA_F_NOPREFIXROUTE and if there is an address
present with this flag, to not cleanup the route. Instead, assume
that userspace is taking care of this route.
Also perform the same cleanup, when userspace changes an existing address
to add NOPREFIXROUTE (to an address that didn't have this flag). This is
done because when the address was added, a prefix route was created for it.
Since the user now wants to handle this route by himself, we cleanup this
route.
This cleanup of the route is not totally robust. There is no guarantee,
that the route we are about to delete was really the one added by the
kernel. This behavior does not change by the patch, and in practice it
should work just fine.
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding/modifying an IPv6 address, the userspace application needs
a way to suppress adding a prefix route. This is for example relevant
together with IFA_F_MANAGERTEMPADDR, where userspace creates autoconf
generated addresses, but depending on on-link, no route for the
prefix should be added.
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add sctp_spp_sackdelay_{enable|disable} helper function for
avoiding code duplication.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two places defined IPV6_TCLASS_SHIFT, so we should move it into ipv6.h,
and use this macro as possible. And define ip6_tclass helper to return
tclass
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.15.4 and Bluetooth networking stacks share 6lowpan compression
code. Instead of introducing Makefile/Kconfig hacks, build this code as
a separate module referenced from both ieee802154 and bluetooth modules.
This fixes the following build error observed in some kernel
configurations:
net/built-in.o: In function `header_create': 6lowpan.c:(.text+0x166149): undefined reference to `lowpan_header_compress'
net/built-in.o: In function `bt_6lowpan_recv': (.text+0x166b3c): undefined reference to `lowpan_process_data'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Eremin-Solenikov <dmitry_eremin@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>