Move fl_starv_thres into adapter->sge data structure since it
_could_ be different from adapter to adapter. Also move other per-adapter
SGE values which had been treated as driver globals into adapter->sge.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1b7bde6d65 ("net: fec: implement rx_copybreak to improve rx performance")
introduced a regression for i.MX28. The swap_buffer() function doing
the endian conversion of the received data on i.MX28 may access memory
beyond the actual packet size in the DMA buffer. fec_enet_copybreak()
does not copy those bytes, so that the last bytes of a packet may be
filled with invalid data after swapping.
This will likely lead to checksum errors on received packets.
E.g. when trying to mount an NFS rootfs:
UDP: bad checksum. From 192.168.1.225:111 to 192.168.100.73:44662 ulen 36
Do the byte swapping and copying to the new skb in one go if
necessary.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Poll for the link events only if firmware doesn't have capability
to notify the driver for the link events.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When events arrive at driver load, the event handler gets called even before
the spinlock and list are initialized. Fix this by moving the initialization
before EQs creation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the EQ is created, it can possibly generate interrupts and the interrupt
handler is referencing eq->dev. It is therefore required to set eq->dev before
calling request_irq() so if an event is generated before request_irq() returns,
we will have a valid eq->dev field.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[ 158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.
Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).
Fixes: 3ae8f4e0b9 ('net: mv643xx_eth: Implement software TSO')
Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com>
Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr>
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the atomicity when suspend and resume the
driver. The clk api have been changed (as reported by Hao Liang)
and the skb allocation is done out of the hw setup function and
taking care about the GFP flags.
Reported-by: Hao Liang <hliang1025@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hao Liang <hliang1025@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to fix the concurrency in eee initialization
inside the stmmac driver and related warnings when enable
DEBUG_ATOMIC_SLEEP.
Prior this patch, the stmmac_eee_init could be called in several places
as shown below:
stmmac_open stmmac_resume PHY Layer
| | |
stmmac_hw_setup stmmac_adjust_link
| | stmmac ethtool
|__________________________|______________|
|
stmmac_eee_init
The patch removes the stmmac_eee_init call inside the stmmac_hw_setup
that is unnecessary. It is sufficient to call it in the adjust_link to
always guarantee that EEE is always configured at mac level too.
Fixing the lock protection now it is covered another case (not
considered before). The stmmac_eee_init could be called by the ethtool
so critical sections must be protected inside this function too.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing spin_unlock when tx frames gets dropped.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_tx_avail() may lie if used unprotected. It's using cur_tx
and dirty_tx index. These index may be already in use by tx_clean
when entering xmit routine. So, this should be called locked.
This can cause transmit queue to be stuck, with following message:
NETDEV WATCHDOG: eth0 (stmmaceth): transmit queue 0 timed out
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microblaze is a fpga soft core, it can be customized easily, which may
cause many various hardware version strings.
So the original fix patch based on hard-coded compatible version strings
is not a good idea (although it is correct for current issue). For it,
there will be a new solving way soon (which based on the device tree).
The original issue is related with qemu, so can only change the hardware
version string in qemu for it, then keep the original driver no touch (
qemu is for virtualization which has much easier life than real world).
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following kernel crash during SGMII based 1GbE probe.
BUG: Bad page state in process swapper/0 pfn:40fe6ad
page:ffffffbee37a75d8 count:-1 mapcount:0 mapping: (null) index:0x0
flags: 0x0()
page dumped because: nonzero _count
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0+ #7
Call trace:
[<ffffffc000087fa0>] dump_backtrace+0x0/0x12c
[<ffffffc0000880dc>] show_stack+0x10/0x1c
[<ffffffc0004d981c>] dump_stack+0x74/0xc4
[<ffffffc00012fe70>] bad_page+0xd8/0x128
[<ffffffc000133000>] get_page_from_freelist+0x4b8/0x640
[<ffffffc000133260>] __alloc_pages_nodemask+0xd8/0x834
[<ffffffc0004194f8>] __netdev_alloc_frag+0x124/0x1b8
[<ffffffc00041bfdc>] __netdev_alloc_skb+0x90/0x10c
[<ffffffc00039ff30>] xgene_enet_refill_bufpool+0x11c/0x280
[<ffffffc0003a11a4>] xgene_enet_process_ring+0x168/0x340
[<ffffffc0003a1498>] xgene_enet_napi+0x1c/0x50
[<ffffffc00042b454>] net_rx_action+0xc8/0x18c
[<ffffffc0000b0880>] __do_softirq+0x114/0x24c
[<ffffffc0000b0c34>] irq_exit+0x94/0xc8
[<ffffffc0000e68a0>] __handle_domain_irq+0x8c/0xf4
[<ffffffc000081288>] gic_handle_irq+0x30/0x7c
This was due to hardware resource sharing conflict with the firmware. This
patch fixes this crash by using resources (descriptor ring, prefetch buffer)
that are not shared.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support when used with older firmware (<= 1.13.28).
- Added xgene_ring_mgr_init() to check whether ring manager is initialized
- Calling xgene_ring_mgr_init() from xgene_port_ops.reset()
- To handle errors, changed the return type of xgene_port_ops.reset()
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_ef10_probe() was BUGging out if the BAR2 size was 0. This is
unnecessarily violent; instead we should just fail to probe the device.
Kept a WARN_ON as this problem indicates a broken or misconfigured NIC.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMC91x is written to explicitly look up the IRQ resource
from the platform device and extract the IRQ and flags, however
the platform_get_irq() does additional things, like call
of_irq_get() in the device tree case, which will translate
the IRQ using the irqdomain and defer the probe if the
IRQ host cannot be found.
As we're not looking up the resource, this will not retrieve
the IRQ flags, but that is better done using
irqd_get_trigger_type(), as the trigger is what the driver
wants to modify. We take care to preserve the semantics that
will make the trigger type provided from the resource
override any local specifier.
Tested on the Nomadik NHK15 which has its SMC91x IRQ line
connected to a STMPE2401 GPIO expander on I2C.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When use current latest upstream qemu (current version: 2.1.2), need let
driver compatible with 'xlnx,xps-ethernetlite-2.00.b', or can not find
net device in microblaze qemu. Related QEMU commands under fedora 20:
yum install libvirt
yum install tunctl
tunctl -b
ip link set tap0 up
brctl addif virbr0 tap0
./microblaze-softmmu/qemu-system-microblaze -M petalogix-s3adsp1800 \
-kernel ../linux-stable.microblaze/arch/microblaze/boot/linux.bin \
-no-reboot -append "console=ttyUL0,115200 doreboot" -nographic \
-net nic,vlan=0,model=xlnx.xps-ethernetlite,macaddr=00:16:35:AF:94:00 \
-net tap,vlan=0,ifname=tap0,script=no,downscript=no
in microblaze qemu bash (guest machine):
ifconfig eth0 add 192.168.122.2 netmask 255.255.255.0
ifconfig eth0 up
After add this patch, can find the device, and can be used by 'telnetd'
(need cross-build busybox with glibc for it), then outside can telnet to
it without password.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of bcm_sysport_init_tx_ring() can currently fail, and will
always call bcm_sysport_fini_tx_ring() in a loop ending at the number of
TX queues (32) without checking if the TX ring was successfully
initialized or not.
Update bcm_sysport_fini_tx_ring() to return early and avoid a crash
de-referencing ring->cbs if the TX ring was not initialized, since
ring->cbs is the last part of the initialization done by
bcm_sysport_init_tx_ring() that could fail.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be allocating a single byte of DMA coherent memory, but
instead a full-sized struct dma_desc (8 bytes).
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we are allocating memory using kzalloc for struct mvpp2_prs_entry,
but later when we are getting error we were just returning the error
value without releasing the memory.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3b57de958e brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast and ucast filter entries)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.
One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a906 "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".
While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.
The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.
Fixes: 837052d0cc ('net/mlx4_en: Add netdev support for TCP/IP
offloads of vxlan tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-10-30
This series contains updates to e1000, igb and ixgbe.
Francesco Ruggeri fixes an issue with e1000 where in a VM the driver did
not support unicast filtering.
Roman Gushchin fixes an issue with igb where the driver was re-using
mapped pages so that packets were still getting dropped even if all
the memory issues are gone and there is free memory.
Junwei Zhang found where in the ixgbe_clean_rx_ring() we were repeating
the assignment of NULL to the receive buffer skb and fixes it.
Emil fixes a race condition between setup_link and SFP detection routine
in the watchdog when setting the advertised speed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
win0_lock was being used un-initialized, resulting in warning traces
being seen when lock debugging is enabled (and just wrong)
Fixes : fc5ab02096 ('cxgb4: Replaced the backdoor mechanism to access the HW
memory with PCIe Window method')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following commands:
modprobe ixgbe
ifconfig ethX up
ethtool -s ethX advertise 0x020
can lead to "setup link failed with code -14" error due to the setup_link
call racing with the SFP detection routine in the watchdog.
This patch resolves this issue by protecting the setup_link call with check
for __IXGBE_IN_SFP_INIT.
Reported-by: Scott Harrison <scoharr2@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Incoming packet is dropped silently by sk_filter(), if the skb was
allocated from pfmemalloc reserves and the corresponding socket is
not marked with the SOCK_MEMALLOC flag.
Igb driver allocates pages for DMA with __skb_alloc_page(), which
calls alloc_pages_node() with the __GFP_MEMALLOC flag. So, in case
of OOM condition, igb can get pages with pfmemalloc flag set.
If an incoming packet hits the pfmemalloc page and is large enough
(small packets are copying into the memory, allocated with
netdev_alloc_skb_ip_align(), so they are not affected), it will be
dropped.
This behavior is ok under high memory pressure, but the problem is
that the igb driver reuses these mapped pages. So, packets are still
dropping even if all memory issues are gone and there is a plenty
of free memory.
In my case, some TCP sessions hang on a small percentage (< 0.1%)
of machines days after OOMs.
Fix this by avoiding reuse of such pages.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Tested-by: Aaron Brown "aaron.f.brown@intel.com"
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VMWare's e1000 implementation does not seem to support unicast filtering.
This can be observed by configuring a macvlan interface on eth0 in a VM in
VMWare Fusion 5.0.5, and trying to use that interface instead of eth0.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. Remove the rcu_read_lock/unlock around rcu_access_pointer
2. Replace the rcu_dereference with rcu_access_pointer
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced repetive Device ID's which got added in commit b961f9a488
("cxgb4vf: Remove superfluous "idx" parameter of CH_DEVICE() macro")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sysport_resume() was missing an UniMAC reset which can lead to
various receive FIFO corruptions coming out of a suspend cycle. If the
RX FIFO is stuck, it will deliver corrupted/duplicate packets towards
the host CPU interface.
This could be reproduced on crowded network and when Wake-on-LAN is
enabled for this particular interface because the switch still forwards
packets towards the host CPU interface (SYSTEMPORT), and we had to leave
the UniMAC RX enable bit on to allow matching MagicPackets.
Once we re-enter the resume function, there is a small window during
which the UniMAC receive is still enabled, and we start queueing
packets, but the RDMA and RBUF engines are not ready, which leads to
having packets stuck in the UniMAC RX FIFO, ultimately delivered towards
the host CPU as corrupted.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a small window during which the SYSTEMPORT adapter
enables its RX interrupts without having enabled its NAPI handler, which
can result in packets to be discarded during interface bringup.
A similar but more serious window exists in bcm_sysport_resume() during
which we can have the RDMA engine not fully prepared to receive packets
and yet having RX interrupts enabled.
Fix this my moving the RX interrupt enable down to
bcm_sysport_netif_start() after napi_enable() for the RX path is called,
which fixes both call sites: bcm_sysport_open() and
bcm_sysport_resume().
Fixes: b02e6d9ba7 ("net: systemport: add bcm_sysport_netif_{enable,stop}")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling DCBx in firmware automatically enables DCBx for control via host
lldp agents. Wait for an explicit setstate call from an lldp agents to enable
DCBx instead.
Fixes: 76bcb31efc ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear out any DCB apps we might have added to kernel table when we lose DCB
sync (or IEEE equivalent event). These were previously left behind and not
cleaned up correctly. IEEE allows individual components to work independently,
so improve check for IEEE completion by specifying individual components.
Fixes: 10b0046685 ("cxgb4: IEEE fixes for DCBx state machine")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After moving the EQ ownership to software effectively destroying it, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After destroying the EQ, the object responsible for generating interrupts, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer. This patch solves a very
rare case when we get panic on driver unload.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c: In function ‘xgene_enet_ecc_init’:
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c:126: warning: ‘data’ may be used uninitialized in this function
Depending on the arbitrary value on the stack, the loop may terminate
too early, and cause a bogus -ENODEV failure.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally mask by the _SHIFT variable. It means that "event" is
always zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the amd-xgbe driver increments the packets processed counter
each time a descriptor is processed. Since a packet can be represented
by more than one descriptor incrementing the counter in this way is not
appropriate. Also, since multiple descriptors cause the budget check
to be short circuited, sometimes the returned value from the poll
function would be larger than the budget value resulting in a WARN_ONCE
being triggered.
Update the polling logic to properly account for the number of packets
processed and exit when the budget value is reached.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_features callback function was improperly using an unsigned
int to save the current feature value for features such as NETIF_F_RXCSUM.
Since that feature is in the upper 32 bits of a 64 bit variable the
result was always 0 making it not possible to actually turn off the
hardware RX checksum support. Change the unsigned int type to the
netdev_features_t type in order to properly capture the current value
and perform the proper operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
