Since 5.10-rc1, i.MX has been converted to a devicetree-only platform.
The platform data support in this driver was only used for non-DT
platforms.
Remove the platform data support as it has no more users.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210118121549.1625217-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add DMA_PRIVATE attribute flag to idxd DMA channels. The dedicated WQs are
expected to be used by a single client and not shared. While doing NTB
testing this mistake was discovered, which prevented ntb_transport from
requesting DSA wqs as DMA channels via dma_request_channel().
Reported-by: Srinijia Kambham <srinija.kambham@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Srinijia Kambham <srinija.kambham@intel.com>
Fixes: 8f47d1a5e5 ("dmaengine: idxd: connect idxd to dmaengine subsystem")
Link: https://lore.kernel.org/r/161074758743.2184057.3388557138816350980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Nikhil reported the misc interrupt handler can sometimes miss handling
the command interrupt when an error interrupt happens near the same time.
Have the irq handling thread continue to process the misc interrupts until
all interrupts are processed. This is a low usage interrupt and is not
expected to handle high volume traffic. Therefore there is no concern of
this thread running for a long time.
Fixes: 0d5c10b4c8 ("dmaengine: idxd: add work queue drain support")
Reported-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161074755329.2183844.13295528344116907983.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On Intel Tangier B0 and Anniedale the interrupt line, disregarding
to have different numbers, is shared between HSU DMA and UART IPs.
Thus on such SoCs we are expecting that IRQ handler is called in
UART driver only. hsu_pci_irq was handling the spurious interrupt
from HSU DMA by returning immediately. This wastes CPU time and
since HSU DMA and HSU UART interrupt occur simultaneously they race
to be handled causing delay to the HSU UART interrupt handling.
Fix this by disabling the interrupt entirely.
Fixes: 4831e0d905 ("serial: 8250_mid: handle interrupt correctly in DMA case")
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210112223749.97036-1-ftoth@exalondelft.nl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The UDMA and BCDMA can provide higher throughput if the burst_size of the
channel is changed from it's default (which is 64 bytes) for Ultra-high
and high capacity channels.
This performance benefit is even more visible when the buffers are aligned
with the burst_size configuration.
The am654 does not have a way to change the burst size, but it is using
64 bytes burst, so increasing the copy_align from 8 bytes to 64 (and
clients taking that into account) can increase the throughput as well.
Numbers gathered on j721e:
echo 8000000 > /sys/module/dmatest/parameters/test_buf_size
echo 2000 > /sys/module/dmatest/parameters/timeout
echo 50 > /sys/module/dmatest/parameters/iterations
echo 1 > /sys/module/dmatest/parameters/max_channels
Prior this patch: ~1.3 GB/s
After this patch: ~1.8 GB/s
with 1 byte alignment: ~1.7 GB/s
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210113114923.9231-3-peter.ujfalusi@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
BCDMA RX channels have one flow per channel, therefore set the rflow_cnt
to rchan_cnt.
Without this patch, request for BCDMA RX channel allocation fails as
rflow_cnt is 0 thus fails to reserve a rflow for the channel.
Fixes: 8844898028 ("dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210112141403.30286-1-vigneshr@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When building with CONFIG_UBSAN_UNSIGNED_OVERFLOW, clang decides not to
inline gpi_update_reg, which causes a linkage failure around __bad_mask:
ld.lld: error: undefined symbol: __bad_mask
>>> referenced by bitfield.h:119 (include/linux/bitfield.h:119)
>>> dma/qcom/gpi.o:(gpi_update_reg) in archive drivers/built-in.a
>>> referenced by bitfield.h:119 (include/linux/bitfield.h:119)
>>> dma/qcom/gpi.o:(gpi_update_reg) in archive drivers/built-in.a
If gpi_update_reg is not inlined, the mask value will not be known at
compile time so the check in field_multiplier stays in the final
object file, causing the above linkage failure. Always inline
gpi_update_reg so that this check can never fail.
Fixes: 5d0c3533a1 ("dmaengine: qcom: Add GPI dma driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1243
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20210112191214.1264793-1-natechancellor@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A 'dma_pool_destroy()' call is missing in the remove function.
Add it.
This call is already made in the error handling path of the probe function.
Fixes: 47e20577c2 ("dmaengine: Add Actions Semi Owl family S900 DMA driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201212162535.95727-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In case of error, the previous 'fsl_dma_chan_probe()' calls must be undone
by some 'fsl_dma_chan_remove()', as already done in the remove function.
It was added in the remove function in commit 77cd62e808 ("fsldma: allow
Freescale Elo DMA driver to be compiled as a module")
Fixes: d3f620b2c4 ("fsldma: simplify IRQ probing and handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201212160614.92576-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A 'irq_dispose_mapping()' call is missing in the remove function.
Add it.
This is needed to undo the 'irq_of_parse_and_map() call from the probe
function and already part of the error handling path of the probe function.
It was added in the probe function only in commit d3f620b2c4 ("fsldma:
simplify IRQ probing and handling")
Fixes: 77cd62e808 ("fsldma: allow Freescale Elo DMA driver to be compiled as a module")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201212160516.92515-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add DMA controller driver for Lightning Mountain (LGM) family of SoCs.
The main function of the DMA controller is the transfer of data from/to any
peripheral to/from the memory. A memory to memory copy capability can also
be configured.
This ldma driver is used for configure the device and channnels for data
and control paths.
Signed-off-by: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@linux.intel.com>
Link: https://lore.kernel.org/r/5fc54eb7ccfad4f8dd812b66b884054fc55cf050.1606905330.git.mallikarjunax.reddy@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
mutex lock can be initialized automatically with DEFINE_MUTEX()
rather than explicitly calling mutex_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20201224132254.30961-1-zhengyongjun3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
linux/platform_data/dma-atmel.h is only used by the at_hdmac driver. Move
the CFG bits definitions back in at_hdmac_regs.h and the remaining
definitions in the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201228203022.2674133-1-alexandre.belloni@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DMA controller present on the Actions Semi S500 SoC is compatible
with the S900 variant, so add it to the list of devices supported by
the Actions Semi Owl DMA driver. Additionally, order the entries
alphabetically.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/88dc9dc064fd4c71f7ad46f172b05b09b9777e42.1609263738.git.cristian.ciocaltea@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In xilinx_dma_child_probe function, the nr_channels variable is
passed to of_property_read_u32() which expects an u32 return value
pointer. Modify the nr_channels variable type from int to u32 to
fix the incompatible parameter coverity warning.
Addresses-Coverity: Event incompatible_param.
Fixes: 1a9e7a03c7 ("dmaengine: vdma: Add support for mulit-channel dma mode")
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1608722462-29519-3-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gcc points out an incorrect error handling loop:
drivers/dma/qcom/gpi.c: In function 'gpi_ch_init':
drivers/dma/qcom/gpi.c:1254:15: error: iteration 2 invokes undefined behavior [-Werror=aggressive-loop-optimizations]
1254 | struct gpii *gpii = gchan->gpii;
| ^~~~
drivers/dma/qcom/gpi.c:1951:2: note: within this loop
1951 | for (i = i - 1; i >= 0; i++) {
| ^~~
Change the loop to correctly walk backwards through the
initialized fields rather than off into the woods.
Fixes: 5d0c3533a1 ("dmaengine: qcom: Add GPI dma driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210103135738.3741123-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The parameter of kfree function is NULL, so kfree code is useless, delete it.
Therefore, goto expression is no longer needed, so simplify it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201216130649.13979-1-zhengyongjun3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the dw_edma_alloc_burst() function fails then we free "chunk" but
it's still on the "desc->chunk->list" list so it will lead to a use
after free. Also the "->chunks_alloc" count is incremented when it
shouldn't be.
In current kernels small allocations are guaranteed to succeed and
dw_edma_alloc_burst() can't fail so this will not actually affect
runtime.
Fixes: e63d79d1ff ("dmaengine: Add Synopsys eDMA IP core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/X9dTBFrUPEvvW7qc@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'disable_xdmac()' should be called in the error handling path of the
probe function to undo a previous 'enable_xdmac()' call, as already
done in the remove function.
Fixes: a6e9be055d ("dmaengine: milbeaut-xdmac: Add XDMAC driver for Milbeaut platforms")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201219132800.183254-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'mtk_hsdma_hw_deinit()' should be called in the error handling path of the
probe function to undo a previous 'mtk_hsdma_hw_init()' call, as already
done in the remove function.
Fixes: 548c4597e9 ("dmaengine: mediatek: Add MediaTek High-Speed DMA controller for MT7622 and MT7623 SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201219124718.182664-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
drivers/dma/qcom/gpi.c:1419:3: warning: format '%lu' expects argument of
type 'long unsigned int', but argument 8 has type 'size_t {aka unsigned
int}' [-Wformat=]
drivers/dma/qcom/gpi.c:1427:31: warning: format '%lu' expects argument of
type 'long unsigned int', but argument 3 has type 'size_t {aka unsigned
int}' [-Wformat=]
drivers/dma/qcom/gpi.c:1447:3: warning: format '%llx' expects argument of
type 'long long unsigned int', but argument 4 has type 'dma_addr_t {aka
unsigned int}' [-Wformat=]
drivers/dma/qcom/gpi.c:1447:3: warning: format '%llx' expects argument of
type 'long long unsigned int', but argument 5 has type 'phys_addr_t {aka
unsigned int}' [-Wformat=]
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201218104137.59200-1-nixiaoming@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The clean up is off by one so this will start at "i" and it should start
with "i - 1" and then it doesn't unregister the zeroeth elements in the
array.
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/X9nFeojulsNqUSnG@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of initializing the rchan_tpl the initial commit re-initialized
the tchan_tpl.
Fixes: d2abc98233 ("dmaengine: ti: k3-udma: Initial support for K3 PKTDMA")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201216154833.20821-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New drivers/devices
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
- Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI keystone drivers for 5.11 included here due to dependency for TI
drivers
-----BEGIN PGP SIGNATURE-----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=uNBn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"The last dmaengine updates for this year :)
This contains couple of new drivers, new device support and updates to
bunch of drivers.
New drivers/devices:
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI drivers"
* tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (75 commits)
soc: ti: k3-ringacc: Use correct error casting in k3_ringacc_dmarings_init
dmaengine: ti: k3-udma-glue: Add support for K3 PKTDMA
dmaengine: ti: k3-udma: Initial support for K3 PKTDMA
dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling
dmaengine: ti: k3-udma: Initial support for K3 BCDMA
soc: ti: k3-ringacc: add AM64 DMA rings support.
dmaengine: ti: Add support for k3 event routers
dmaengine: ti: k3-psil: Add initial map for AM64
dmaengine: ti: k3-psil: Extend psil_endpoint_config for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 BCDMA
dmaengine: dmatest: Use dmaengine_get_dma_device
dmaengine: doc: client: Update for dmaengine_get_dma_device() usage
dmaengine: Add support for per channel coherency handling
dmaengine: of-dma: Add support for optional router configuration callback
dmaengine: ti: k3-udma-glue: Configure the dma_dev for rings
dmaengine: ti: k3-udma-glue: Get the ringacc from udma_dev
dmaengine: ti: k3-udma-glue: Add function to get device pointer for DMA API
dmaengine: ti: k3-udma: Add support for second resource range from sysfw
dmaengine: ti: k3-udma: Wait for peer teardown completion if supported
...
This commit adds support for PKTDMA in k3-udma glue driver. Use new
psil_endpoint_config struct to get static data for a given channel or a
flow during setup. Make sure that the RX flows being mapped to a RX
channel is within the range of flows that is been allocated to that RX
channel.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-21-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the DMAs introduced with AM64 is the Packet DMA (PKTDMA).
It serves similar purpose as K3 UDMAP channels in packet mode, but with
notable differences, like tflow support and channels being allocated to
service specific peripherals.
The rings for the PKTDMA is integrated within the DMA itself instead of
using rings from the general purpose ringacc.
PKTDMA can be used to service PSI-L peripherals, similarly to
K3 UDMA channels.
Most of the driver code can be reused for PKTDMA tchan/rchan support but
new setup and allocation functions are needed to handle the differences
between the DMAs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-20-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Unlike UDMAP the BCDMA defines the channel TPL levels per channel type.
In UDMAP the number of high and ultra-high channels applies to both tchan
and rchan.
BCDMA defines the TPL per channel types: bchan, tchan and rchan can have
different number of high and ultra-high channels.
In order to support BCDMA channel TPL we need to move the tpl information
as per channel type property for the DMAs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-19-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the DMAs introduced with AM64 is the Block Copy DMA (BCDMA).
It serves similar purpose as K3 UDMAP channels in TR mode.
The rings for the BCDMA is integrated within the DMA itself instead of
using rings from the general purpose ringacc.
A BCDMA have two different type of channels:
- Block Copy Channels (bchan)
- Split Channels (tchan and rchan)
tchan and rchan can be used to service PSI-L peripherals, similarly to
K3 UDMA channels.
bchan can be only used for block copy operation (TR type15) like the
paired K3 UDMA tchan/rchan configured in block copy mode.
bchans can be also used to service peripherals directly if an external
trigger is selected for the channel.
Most of the driver code can be reused for BCDMA bchan/tchan/rchan support
but new setup and allocation functions are needed to handle the
differences between the DMAs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-18-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
By using the dmaengine_get_dma_device() to get the device for
dma_api use, the dmatest can support per channel coherency if it is
supported by the DMA controller.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-11-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Additional configuration for the DMA event router might be needed for a
channel which can not be done during device_alloc_chan_resources callback
since the router information is not yet present for the drivers.
If there is a need for additional configuration for the channel if DMA
router is in use, then the driver can implement the device_router_config
callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-8-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rings in RING mode should be using the DMA device for DMA API as in this
mode the ringacc will not access the ring memory in any ways, but the DMA
is.
Fix up the ring configuration and set the dma_dev unconditionally and let
the ringacc driver to select the correct device to use for DMA API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-7-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If of_xudma_dev_get() returns with the valid udma_dev then the driver
already got the ringacc, there is no need to execute
of_k3_ringacc_get_by_phandle() for each channel via the glue layer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-6-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Glue layer users should use the device of the DMA for DMA mapping and
allocations as it is the DMA which accesses to descriptors and buffers,
not the clients
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-5-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Resource allocation via sysfw can use up to two ranges per resource subtype
to support more complex resource assignment, mainly for DMA channels.
Take the second range also into consideration when setting up the maps for
available resources.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-4-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Set the TDTYPE if it is supported on the platform (j721e) which will cause
UDMAP to wait for the remote peer to finish the teardown before returning
the teardown completed message.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-3-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to different sections of the TRM, the hchan_cnt of CAP3 includes
the number of uchan in UDMA, thus the start offset of the normal channels
are hchan_cnt.
Fixes: daf4ad0499 ("dmaengine: ti: k3-udma: Query throughput level information from hardware")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To avoid multiple entries in MDMA interrupt handler for each flag&interrupt
enable, manage all flags set at once.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-5-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DMA_SxPAR or DMA_SxM0AR/M1AR registers have to be aligned on PSIZE or MSIZE
respectively. This means that bus width needs to be forced to 1 byte when
computed width is not aligned with address.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-4-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When dma_channel_release is called, it means that the channel won't be used
anymore with the configuration it had. To ensure a future client can safely
use the channel after it has been released, clean the configuration done
when channel was requested.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-3-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To better understand error that can be detected by the DMA controller,
manage the error flags before the transfer flags.
This way, it is possible to know if the FIFO error flag is set for an
over/underrun condition or a FIFO level error.
When a FIFO over/underrun condition occurs, the data is not lost because
peripheral request is not acknowledged by the stream until the over/
underrun condition is cleared. If this acknowledge takes too much time,
the peripheral itself may detect an over/underrun condition of its internal
buffer and data might be lost.
That's why in case the FIFO error flag is set, we check if the channel is
disabled or not, and if a Transfer Complete flag is set, which means that
the channel is disabled because of the end of transfer.
Because channel is disabled by hardware either by a FIFO level error, or by
an end of transfer.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-2-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While performing suspend/resume, we were getting below kernel crash.
[ 54.541672] [FTS][Info]gesture suspend...
[ 54.605256] [FTS][Error][GESTURE]Enter into gesture(suspend) failed!
[ 54.605256]
[ 58.345850] irq event 10: bogus return value fffffff3
......
[ 58.345966] [<ffff0000080830f0>] el1_irq+0xb0/0x124
[ 58.345971] [<ffff000008085360>] arch_cpu_idle+0x10/0x18
[ 58.345975] [<ffff0000081077f4>] do_idle+0x1ac/0x1e0
[ 58.345979] [<ffff0000081079c8>] cpu_startup_entry+0x20/0x28
[ 58.345983] [<ffff000008a80ed0>] rest_init+0xd0/0xdc
[ 58.345988] [<ffff0000091c0b48>] start_kernel+0x390/0x3a4
[ 58.345990] handlers:
[ 58.345994] [<ffff0000085120d0>] bam_dma_irq
The reason for the crash we found is, bam_dma_irq() was returning
negative value when the device resumes in some conditions.
In addition, the irq handler should have one of the below return values.
IRQ_NONE interrupt was not from this device or was not handled
IRQ_HANDLED interrupt was handled by this device
IRQ_WAKE_THREAD handler requests to wake the handler thread
Therefore, to resolve this crash, we have changed the return value to
IRQ_NONE.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Link: https://lore.kernel.org/r/1607322820-7450-1-git-send-email-sparth1292@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to allow configuration of Intel Analytics Accelerator (IAX) in
addition to the Intel Data Streaming Accelerator (DSA). The IAX hardware
has the same configuration interface as DSA. The main difference
is the type of operations it performs. We can support the DSA and
IAX devices on the same driver with some tweaks.
IAX has a 64B completion record that needs to be 64B aligned, as opposed to
a 32B completion record that is 32B aligned for DSA. IAX also does not
support token management.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160564555488.1834439.4261958859935360473.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update the kerneldoc function headers to fix build warnings:
drivers/dma/qcom/qcom_adm.c:180: warning: Function parameter or member 'chan' not described in 'adm_free_chan'
drivers/dma/qcom/qcom_adm.c:190: warning: Function parameter or member 'burst' not described in 'adm_get_blksize'
drivers/dma/qcom/qcom_adm.c:466: warning: Function parameter or member 'chan' not described in 'adm_terminate_all'
drivers/dma/qcom/qcom_adm.c:466: warning: Excess function parameter 'achan' description in 'adm_terminate_all'
drivers/dma/qcom/qcom_adm.c:503: warning: Function parameter or member 'achan' not described in 'adm_start_dma'
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/20201126184602.GA1008@earth.li
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the main table should be
always used and the of_match_ptr does not have any sense (this also
allows ACPI matching via PRP0001, even though it is not relevant here).
The secondary match of_device_id tables (passed to of_match_node) should
be marked as maybe unused to fix compile testing (!CONFIG_OF on x86_64)
warnings:
drivers/dma/ti/dma-crossbar.c:125:34: warning:
‘ti_am335x_master_match’ defined but not used [-Wunused-const-variable=]
drivers/dma/ti/dma-crossbar.c:22:34: warning:
‘ti_dma_xbar_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-6-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver uses a second of_device_id table in the probe()
function by passing it to of_match_node(). This code will be a no-op
for compile testing (!CONFIG_OF on x86_64):
drivers/dma/stm32-dmamux.c:171:34: warning:
‘stm32_stm32dma_master_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-5-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/sf-pdma/sf-pdma.c:576:34: warning:
‘sf_pdma_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-4-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/mv_xor.c:1281:34: warning:
‘mv_xor_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-3-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c:984:34: warning:
‘dw_dma_of_id_table’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dma-jz4780.c:1031:34: warning:
‘jz4780_dma_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The mxs-dma driver is only used by DT platforms and the .id_table
is unused.
Get rid of it to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123193051.17285-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201124143405.2764-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This controller provides DMAengine capabilities for a variety of peripheral
buses such as I2C, UART, and SPI. By using GPI dmaengine driver, bus
drivers can use a standardize interface that is protocol independent to
transfer data between memory and peripheral.
Link: https://lore.kernel.org/r/20201109085450.24843-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the DMA engine driver for the QCOM Application Data Mover (ADM) DMA
controller found in the MSM8x60 and IPQ/APQ8064 platforms.
The ADM supports both memory to memory transactions and memory
to/from peripheral device transactions. The controller also provides
flow control capabilities for transactions to/from peripheral devices.
The initial release of this driver supports slave transfers to/from
peripherals and also incorporates CRCI (client rate control interface)
flow control.
The hardware only supports a 32 bit physical address, so specifying
!PHYS_ADDR_T_64BIT gives maximum COMPILE_TEST coverage without having to
spend effort on kludging things in the code that will never actually be
needed on real hardware.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/20201114140233.GM32650@earth.li
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The error codes were not set on some of these error paths.
Also the error handling was more confusing than it needed to be so I
cleaned it up and shuffled it around a bit.
Fixes: d2fb0a0438 ("dmaengine: break out channel registration")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201113101631.GE168908@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201116202403.29749-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit 7f832645d0 ("dmaengine: ioatdma: remove ioatdma v2 registration")
missed to remove dca2_tag_map_valid() during its removal. Hence, since
then, dca2_tag_map_valid() is unused and make CC=clang W=1 warns:
drivers/dma/ioat/dca.c:44:19:
warning: unused function 'dca2_tag_map_valid' [-Wunused-function]
So, remove this unused function and get rid of a -Wused-function warning.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201113081248.26416-1-lukas.bulwahn@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Portal size is 4k. Current code is mapping all 4 portals in a single chunk.
Restrict the mapped portal size to a single portal to ensure that submission
only goes to the intended portal address.
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160513342642.510187.16450549281618747065.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We now use cpu_pm for saving and restoring device context for deeper SoC
idle states. But for omap3, we must also block idle if SDMA is busy.
If we don't block idle when SDMA is busy, we eventually end up saving and
restoring SDMA register state on PER domain idle while SDMA is active and
that causes at least audio playback to fail.
Fixes: 4c74ecf792 ("dmaengine: ti: omap-dma: Add device tree match data and use it for cpu_pm")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201109154013.11950-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SG capability is inherently present with Multichannel DMA operation.
The register used to check for this capability with other DMA driver types
is not defined for MCDMA.
Fixes: 6ccd692bfb ("dmaengine: xilinx_dma: Add Xilinx AXI MCDMA Engine driver support")
Signed-off-by: Matthew Murrian <matthew.murrian@goctsi.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1604473206-32573-4-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Several code sections incorrectly use struct xilinx_axidma_tx_segment
instead of struct xilinx_aximcdma_tx_segment when operating as
Multichannel DMA. As their structures are similar, this just works.
Fixes: 6ccd692bfb ("dmaengine: xilinx_dma: Add Xilinx AXI MCDMA Engine driver support")
Signed-off-by: Matthew Murrian <matthew.murrian@goctsi.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1604473206-32573-3-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The xilinx_dma_poll_timeout macro is sometimes called while holding a
spinlock (see xilinx_dma_issue_pending() for an example) this means we
shouldn't sleep when polling the dma channel registers. To address it
in xilinx poll timeout macro use readl_poll_timeout_atomic instead of
readl_poll_timeout variant.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1604473206-32573-2-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Link: https://lore.kernel.org/r/20201027215252.25820-11-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201027215252.25820-10-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-9-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-8-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-7-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-6-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: https://lore.kernel.org/r/20201027215252.25820-5-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Cc: Green Wan <green.wan@sifive.com>
Link: https://lore.kernel.org/r/20201027215252.25820-4-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201027215252.25820-3-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Running in hardIRQ, disabling IRQ is redundant since hardIRQ has disabled
IRQ. This patch removes the irqsave and irqstore to save some instruction
cycles.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20201027215252.25820-2-song.bao.hua@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The NAVSS UDMA will stuck if target IP module is disabled by PM while PSI-L
threads are paired UDMA<->IP and no further transfers is possible. This
could be the case for IPs J721E Main CPSW (cpsw9g).
Hence, to avoid such situation do PSI-L threads pairing only when UDMA
channel is going to be enabled as at this time DMA consumer module expected
to be active already.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201030203000.4281-1-grygorii.strashko@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When consumer requests channel power on the DMA controller device
and otherwise on the freeing channel resources.
Note, in some cases consumer acquires channel at the ->probe() stage and
releases it at the ->remove() stage. It will mean that DMA controller device
will be powered during all this time if there is no assist from hardware
to idle it. The above mentioned cases should be investigated separately
and individually.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20201103183938.64752-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add code to "complete" a descriptor when the descriptor or its completion
address hit a fault error when SVA mode is being used. This error can be
triggered due to bad programming by the user. A lock is introduced in order
to protect the descriptor completion lists since the fault handler will run
from the system work queue after being scheduled in the interrupt handler.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160382008092.3911367.12766483427643278985.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add shared workqueue support that includes the support of Shared Virtual
memory (SVM) or in similar terms On Demand Paging (ODP). The shared
workqueue uses the enqcmds command in kernel and will respond with retry if
the workqueue is full. Shared workqueue only works when there is PASID
support from the IOMMU.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/160382007499.3911367.26043087963708134.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The xor_hw_desc local variable is assigned but never read:
drivers/dma/ppc4xx/adma.c: In function ‘ppc440spe_desc_set_src_mult’:
drivers/dma/ppc4xx/adma.c:562:17: warning: variable ‘xor_hw_desc’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201019155756.21445-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ppc440spe_adma_chan_list file-scope variable is not used outside of
the unit so it can be made static.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201019155756.21445-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sama7g5 version of the XDMAC supports priority configuration and
outstanding capabilities.
Add defines for the specific registers for this configuration, together
with recommended settings.
However the settings are very different if the XDMAC is a mem2mem or a
per2mem controller.
Thus, we need to differentiate according to device tree property.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20201016093918.290137-1-eugen.hristev@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SAMA7G5 SoC uses a slightly different variant of the AT_XDMAC.
Added support by a new compatible and a layout struct that copes
to the specific version considering the compatible string.
Only the differences in register map are present in the layout struct.
I reworked the register access for this part that has the differences.
Also the Source/Destination Interface bits are no longer valid for this
variant of the XDMAC. Thus, the layout also has a bool for specifying
whether these bits are required or not.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20201016093850.290053-1-eugen.hristev@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PERID in the CC register for mem2mem operations must match an unused
PERID.
The PERID field is 7 bits, but the selected value is 0x3f.
On later products we can have more reserved PERIDs for actual peripherals,
thus this needs to be increased to maximum size.
Changing the value to 0x7f, which is the maximum for 7 bits field.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20201016093725.289880-1-eugen.hristev@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make use of the new struct_size() helper instead of the offsetof() idiom.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20201008141828.GA20325@embeddedor
Signed-off-by: Vinod Koul <vkoul@kernel.org>
