Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly
named "spi0-1" instead of just "spi0". This commit fixes that.
This DT binding change does not affect any of the in-tree users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.7+
Fixes: 5f597bb2be ("pinctrl: mvebu: add pinctrl driver for Armada 370")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A new revision of the Marvell Armada 38x hardware datasheet unveiled
that the definition of some of the PCIe functions were not
correct. This commit fixes the pinctrl driver accordingly.
Some PCIe functions simply do not exist, some of the PCIe functions in
fact were corresponding to other functions, and some PCIe functions
have been added.
Note: the seemingly unrelated removal of spi(cs2) on MPP47 is related:
this function is in fact implemented on MPP43, instead of a PCIe
function.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.15+
Fixes: ca6d9a084b ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added support to Zynq Ultrascale+ MPSoC on the existing zynq
gpio driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the General I/O block on Axis ETRAX FS SoCs.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Maxim MAX77621 device is high-efficiency, three-phase,
DC-DC step-down switching regulator delivers peak
output currents up to 16A. This device is extension of
MAX8973 and compatible with the register definition.
The MAX77621 has the SHUTDOWN pin which is EN pin on the
MAX8973. On MAX77621, the SHUTDOWN pin (active low) reset
device register to its POR/OTP value. The voltage output
is enabled when SHUTDONW pin is HIGH and EN bit on VOUT
register is HIGH.
For MAX8973, VOUT is enabled when EN bit or EN pin is high.
Add support of the MAX77621 device on max8973 regulator driver
with following changes:
- Make sure SHUTDOWN pin is set HIGH through GPIO calls if
GPIO from AP connected to SHUTDOWN pin provided.
- Enable/disable the rail through register access only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MPX has the _potential_ to cause some issues. Say part of your
init system tried to protect one of its components from buffer
overflows with MPX. If there were a false positive, it's
possible that MPX could keep a system from booting.
MPX could also potentially cause performance issues since it is
present in hot paths like the unmap path.
Allow it to be disabled at boot time.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave@sr71.net>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150607183702.2E8B77AB@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A week late but I managed to complete it all and moved it into Git, for better
structure and easy pulling.
Changes relative to the last submission:
- Added higher level subsystem directories to collect features by
subsystem:
triton:~/tip> ls Documentation/features/
arch-support.txt core debug io lib list-arch.sh locking perf sched seccomp time vm
each subsystem directory contains the feature directories. For example locking
has:
triton:~/tip> ls Documentation/features/locking/
cmpxchg-local lockdep queued-rwlocks queued-spinlocks rwsem-optimized
It's all pretty straightforward to navigate. Advantages are better
visualization, plus git log is able to list changes per subsystem.
- Prettified the visualization some more.
- Improved/corrected the support matrices based on feedback to earlier submissions.
- Updated the support matrices to today's linux-next, so that by the time this
shows up in upstream in the next merge window it's really recent.
Most notably there's a new architecture in linux-next (h8300).
This structure should address all feedback that I got and should minimize the
maintenance overhead (chance of conflicts).
Updated struct file_operations documentation in vfs.txt to match
current implementation
Signed-off-by: Thomas de Beauchene <chauvo_t@epitech.eu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 976591810f (kbuild Update documentation of clean-files and clean-dirs)
changed the example for the clean-files variable, but left the explanation
unchanged. Edit the explanation to match the example.
Signed-off-by: Jeffrey Rogers <jeffreydavidrogers@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Various boot loaders for Exynos based boards use certain memory
addresses during booting for different purposes. Mostly this is one of
following :
1. as a CPU boot address,
2. for storing magic cookie related to low power mode (AFTR, sleep).
The document, based solely on kernel source code, tries to group the
information scattered over different files. This would help in the
future when adding support for new SoC or when extending features
related to low power modes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP: small set of misc. DT fixes; boot fix for THUMB2 kernel
- mediatek: PMIC fixes; DT fix for model name
- exynos: wakeup interupt fixes for 3250
- mvebu: revert mbus patch which broke DMA masters
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gSjy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"About 10 days worth of small bug fixes, and the (hopefully) final
round fixes for from arm-soc land for the -rc cycle. Nothing special
to note, but here's a brief summary of fixes by SoC type:
- OMAP:
small set of misc DT fixes; boot fix for THUMB2 kernel
- mediatek:
PMIC fixes; DT fix for model name
- exynos:
wakeup interupt fixes for 3250
- mvebu:
revert mbus patch which broke DMA masters
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
arm64: dts: mt8173-evb: fix model name
ARM: exynos: Fix wake-up interrupts for Exynos3250
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
soc: mediatek: Add compile dependency to pmic-wrapper
soc: mediatek: PMIC wrap: Fix register state machine handling
soc: mediatek: PMIC wrap: Fix clock rate handling
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Saui
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge omap fixes for v4.1, urgent fix to avoid potential hardware damage From Tony Lindgren:
Omap fixes for the -rc cycle, including a fix for potential hardware
breakage on BeagleBones:
- BeagleBones don't support RTC-only mode, it can cause hardware
damage if system-power-controller is specified without
ti,pmic-shutdown-controller
- Fix a recent regression to am3517 SoCs caused by the recent clock
move that was not noticed until now despite automated boot
testing
- Fix a regression for n900 touchscreen triggered by recent
recent input changes
- Fix compatible property for dm816x USB to avoid errors with
USB Ethernet
- Fix oops for omap3 when built with CONFIG_THUMB2_KERNEL
* tag 'omap-for-v4.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-boneblack: disable RTC-only sleep to avoid hardware damage
ARM: dts: AM35xx: fix system control module clocks
ARM: dts: Fix n900 dts file to work around 4.1 touchscreen regression on n900
ARM: dts: Fix dm816x to use right compatible flag for MUSB
ARM: OMAP3: Fix booting with thumb2 kernel
Rename the following system call entry points:
ia32_cstar_target -> entry_SYSCALL_compat
ia32_syscall -> entry_INT80_compat
The generic naming scheme for x86 system call entry points is:
entry_MNEMONIC_qualifier
where 'qualifier' is one of _32, _64 or _compat.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Initialize and prepare for handling LMCEs. Add a boot-time
option to disable LMCEs.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
[ Simplify stuff, align statements for better readability, reflow comments; kill
unused lmce_clear(); save us an MSR write if LMCE is already enabled. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1433436928-31903-16-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that reserve_ram_pages_type() accepts the WT type, add
set_memory_wt(), set_memory_array_wt() and set_pages_array_wt()
in order to be able to set memory to Write-Through page cache
mode.
Also, extend ioremap_change_attr() to accept the WT type.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-13-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add ioremap_wt() for creating Write-Through mappings on x86. It
follows the same model as ioremap_wc() for multi-arch support.
Define ARCH_HAS_IOREMAP_WT in the x86 version of io.h to
indicate that ioremap_wt() is implemented on x86.
Also update the PAT documentation file to cover ioremap_wt().
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Elliott@hp.com
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: arnd@arndb.de
Cc: hch@lst.de
Cc: hmh@hmh.eng.br
Cc: jgross@suse.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Cc: linux-nvdimm@lists.01.org
Cc: stefan.bader@canonical.com
Cc: yigal@plexistor.com
Link: http://lkml.kernel.org/r/1433436928-31903-8-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a new documentation file explaining the DSCR support on
powerpc platforms. This explains DSCR related data structure, code paths
and also available user interfaces. Any further functional changes to
the DSCR support in the kernel should definitely update the
documentation here.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids. All of the details
are in the shortlog and these patches have been in linux-next with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVzhIcACgkQMUfUDdst+ykY9ACg0HeMGzJAfsWSLiSsBRpDxFAr
ixAAnjOYj4Gv+XtAD4ZiOuMpaQaADntQ
=4uxU
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY driver fixes from Greg KH:
"Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids.
All of the details are in the shortlog and these patches have been in
linux-next with no problems"
* tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
usb: renesas_usbhs: Fix fifo unclear in usbhsf_prepare_pop
usb: gadget: f_fs: fix check in read operation
usb: musb: fix order of conditions for assigning end point operations
usb: gadget: f_uac1: check return code from config_ep_by_speed
usb: gadget: ffs: fix: Always call ffs_closed() in ffs_data_clear()
usb: gadget: g_ffs: Fix counting of missing_functions
usb: s3c2410_udc: correct reversed pullup logic
usb: dwc3: gadget: Fix incorrect DEPCMD and DGCMD status macros
usb: phy: tahvo: Pass the IRQF_ONESHOT flag
usb: phy: ab8500-usb: Pass the IRQF_ONESHOT flag
usb: renesas_usbhs: Revise the binding document about the dma-names
usb: host: xhci: add mutex for non-thread-safe data
usb: make module xhci_hcd removable
USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board
usb: gadget: f_midi: fix segfault when reading empty id
phy: phy-rcar-gen2: Fix USBHS_UGSTS_LOCK value
phy: omap-usb2: invoke pm_runtime_disable on error path
phy: fix Kconfig dependencies
...
APM X-Gene v1 SoC supports its own implementation of MSI, which is not
compliant to GIC V2M specification for MSI Termination.
There is a single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports.
This MSI block supports 2048 MSI termination ports coalesced into 16
physical HW IRQ lines and shared across all 5 PCIe ports.
As there are only 16 HW IRQs to serve 2048 MSI vectors, to support
set_affinity correctly for each MSI vectors, the 16 HW IRQs are statically
allocated to 8 X-Gene v1 cores (2 HW IRQs for each cores). To steer MSI
interrupt to target CPU, MSI vector is moved around these HW IRQs lines.
With this approach, the total MSI vectors this driver supports is reduced
to 256.
[bhelgaas: squash doc, driver, maintainer update]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Follow up to commit e194bbdf36.
Suggested-by: Bandan Das <bsd@redhat.com>
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is now very simple to do. The only interesting part is a simple
trick to find the right memslot in gfn_to_rmap, retrieving the address
space from the spte role word. The same trick is used in the auditing
code.
The comment on top of union kvm_mmu_page_role has been stale forever,
so remove it. Speaking of stale code, remove pad_for_nice_hex_output
too: it was splitting the "access" bitfield across two bytes and thus
had effectively turned into pad_for_ugly_hex_output.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only two ioctls have to be modified; the address space id is
placed in the higher 16 bits of their slot id argument.
As of this patch, no architecture defines more than one
address space; x86 will be the first.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds two boolean properties to FMan Port.
FMan has 3 types of ports:
- 1G ports
By default, all ports support 1G rate
- 10G Ports
Port which use 10G hardware, and configured as 10G
- 10G Best effort ports
Ports which use 1G hardware, configured as 10G, in this case,
the rate is not guaranteed.
The new properties help to distinguish the different type of ports.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The check_acl inode operation and the IPERM_FLAG_RCU flag are long gone; update
the documentation.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Documentation/networking/timestamping/txtimestamp.c: In function ‘__print_timestamp’:
Documentation/networking/timestamping/txtimestamp.c:99:3: warning: format ‘%ld’ expects argument of type ‘long int’, but argument 3 has type ‘int64_t’ [-Wformat=]
fprintf(stderr, " (%+ld us)", cur_ms - prev_ms);
int64_t differs per platform, so a type specifier that differs along
with it is required.
Signed-off-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The current documentation is incomplete wrt the intel_pstate legacy
internal governors. The confusion comes from the general cpufreq
governors which also use the names performance and powersave. This patch
better differentiates between the two sets of governors and gives an
explanation of how the internal P-state governors behave differently from
one another.
Also fix two minor typos.
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: x86@kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Current documentation over use case for EXPORT_SYMBOL_GPL()
only acknowledges functions which are "an internal implementation
issue, and not really an interface". In practice these days
though we have some maintainers taking on preferences to require
all new functionality go in with EXPORT_SYMBOL_GPL().
A maintainer asking developers to use EXPORT_SYMBOL_GPL()
for new functionality tends to be a well accepted and understood
position that maintainers can take and typically requires the
maintainers educating contributing developers on their own
positions and requirements.
Developers who submit code to maintainers not familiar with
these preferences as optional for new functionality need explicit
guidence though as existing documentation does not acknowledge
this as a valid possibility. Without this being documented some
maintainers are reluctant to accept new functionality with
EXPORT_SYMBOL_GPL().
This extends the use case documentation for EXPORT_SYMBOL_GPL()
to acknowledge acceptance for new functionality.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
[jc: wording tweaked with permission]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch includes changes to the external API for SMM support.
Userspace can predicate the availability of the new fields and
ioctls on a new capability, KVM_CAP_X86_SMM, which is added at the end
of the patch series.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Patch "gpiolib: rename gpiod_set_array to gpiod_set_array_value" omitted
to also change the function names in the documentation. Let's fix that.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A33 PIO has 7 ports which starts from PB and has two interrupt ports.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix some spelling typo found in crypto-API.tmpl
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.
Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patches added arch support matrices for more than 40 generic kernel features
that need per architecture support.
The structure of the feature descriptions is the following:
Each feature has its own directory under Documentation/features/subsystem_name/feature_name/,
and the arch-support.txt file shows its current arch porting status.
For example, lockdep support is shown the following way:
triton:~/tip> cat Documentation/features/locking/lockdep/arch-support.txt
#
# Feature name: lockdep
# Kconfig: LOCKDEP_SUPPORT
# description: arch supports the runtime locking correctness debug facility
#
-----------------------
| arch |status|
-----------------------
| alpha: | TODO |
| arc: | ok |
| arm: | ok |
| arm64: | ok |
| avr32: | ok |
| blackfin: | ok |
| c6x: | TODO |
| cris: | TODO |
| frv: | TODO |
| h8300: | TODO |
| hexagon: | ok |
| ia64: | TODO |
| m32r: | TODO |
| m68k: | TODO |
| metag: | ok |
| microblaze: | ok |
| mips: | ok |
| mn10300: | TODO |
| nios2: | TODO |
| openrisc: | TODO |
| parisc: | TODO |
| powerpc: | ok |
| s390: | ok |
| score: | ok |
| sh: | ok |
| sparc: | ok |
| tile: | ok |
| um: | ok |
| unicore32: | ok |
| x86: | ok |
| xtensa: | ok |
-----------------------
For generic kernel features that need architecture support, the
arch-support.txt file in each feature directory shows the arch
support matrix, for all upstream Linux architectures.
The meaning of entries in the tables is:
| ok | # feature supported by the architecture
|TODO| # feature not yet supported by the architecture
| .. | # feature cannot be supported by the hardware
This directory structure can be used in the future to add other
files - such as porting guides, testing description, etc.
The Documentation/features/ hierarchy may also include generic
kernel features that works on every architecture, in that case
the arch-support.txt file will list every architecture as
supported.
To list an architecture's unsupported features, just do something
like:
triton:~/tip> git grep -lE 'x86.*TODO' Documentation/features/*/*/arch-support.txt
Documentation/features/lib/strncasecmp/arch-support.txt
Documentation/features/time/arch-tick-broadcast/arch-support.txt
which will print the list of not yet supported features.
The Documentation/features/list-arch.sh script will print the current
support matrix of one architecture:
triton:~/tip> Documentation/features/list-arch.sh
#
# Kernel feature support matrix of the 'x86' architecture:
#
core/ BPF-JIT : ok | HAVE_BPF_JIT # arch supports BPF JIT optimizations
core/ generic-idle-thread : ok | GENERIC_SMP_IDLE_THREAD # arch makes use of the generic SMP idle thread facility
core/ jump-labels : ok | HAVE_ARCH_JUMP_LABEL # arch supports live patched, high efficiency branches
core/ tracehook : ok | HAVE_ARCH_TRACEHOOK # arch supports tracehook (ptrace) register handling APIs
debug/ gcov-profile-all : ok | ARCH_HAS_GCOV_PROFILE_ALL # arch supports whole-kernel GCOV code coverage profiling
debug/ KASAN : ok | HAVE_ARCH_KASAN # arch supports the KASAN runtime memory checker
debug/ kgdb : ok | HAVE_ARCH_KGDB # arch supports the kGDB kernel debugger
debug/ kprobes : ok | HAVE_KPROBES # arch supports live patched kernel probe
debug/ kprobes-on-ftrace : ok | HAVE_KPROBES_ON_FTRACE # arch supports combined kprobes and ftrace live patching
debug/ kretprobes : ok | HAVE_KRETPROBES # arch supports kernel function-return probes
debug/ optprobes : ok | HAVE_OPTPROBES # arch supports live patched optprobes
debug/ stackprotector : ok | HAVE_CC_STACKPROTECTOR # arch supports compiler driven stack overflow protection
debug/ uprobes : ok | ARCH_SUPPORTS_UPROBES # arch supports live patched user probes
debug/ user-ret-profiler : ok | HAVE_USER_RETURN_NOTIFIER # arch supports user-space return from system call profiler
io/ dma-api-debug : ok | HAVE_DMA_API_DEBUG # arch supports DMA debug facilities
io/ dma-contiguous : ok | HAVE_DMA_CONTIGUOUS # arch supports the DMA CMA (continuous memory allocator)
io/ dma_map_attrs : ok | HAVE_DMA_ATTRS # arch provides dma_*map*_attrs() APIs
io/ sg-chain : ok | ARCH_HAS_SG_CHAIN # arch supports chained scatter-gather lists
lib/ strncasecmp : TODO | __HAVE_ARCH_STRNCASECMP # arch provides an optimized strncasecmp() function
locking/ cmpxchg-local : ok | HAVE_CMPXCHG_LOCAL # arch supports the this_cpu_cmpxchg() API
locking/ lockdep : ok | LOCKDEP_SUPPORT # arch supports the runtime locking correctness debug facility
locking/ queued-rwlocks : ok | ARCH_USE_QUEUED_RWLOCKS # arch supports queued rwlocks
locking/ queued-spinlocks : ok | ARCH_USE_QUEUED_SPINLOCKS # arch supports queued spinlocks
locking/ rwsem-optimized : ok | Optimized asm/rwsem.h # arch provides optimized rwsem APIs
perf/ kprobes-event : ok | HAVE_REGS_AND_STACK_ACCESS_API # arch supports kprobes with perf events
perf/ perf-regs : ok | HAVE_PERF_REGS # arch supports perf events register access
perf/ perf-stackdump : ok | HAVE_PERF_USER_STACK_DUMP # arch supports perf events stack dumps
sched/ numa-balancing : ok | ARCH_SUPPORTS_NUMA_BALANCING # arch supports NUMA balancing
seccomp/ seccomp-filter : ok | HAVE_ARCH_SECCOMP_FILTER # arch supports seccomp filters
time/ arch-tick-broadcast : TODO | ARCH_HAS_TICK_BROADCAST # arch provides tick_broadcast()
time/ clockevents : ok | GENERIC_CLOCKEVENTS # arch support generic clock events
time/ context-tracking : ok | HAVE_CONTEXT_TRACKING # arch supports context tracking for NO_HZ_FULL
time/ irq-time-acct : ok | HAVE_IRQ_TIME_ACCOUNTING # arch supports precise IRQ time accounting
time/ modern-timekeeping : ok | !ARCH_USES_GETTIMEOFFSET # arch does not use arch_gettimeoffset() anymore
time/ virt-cpuacct : ok | HAVE_VIRT_CPU_ACCOUNTING # arch supports precise virtual CPU time accounting
vm/ ELF-ASLR : ok | ARCH_HAS_ELF_RANDOMIZE # arch randomizes the stack, heap and binary images of ELF binaries
vm/ huge-vmap : ok | HAVE_ARCH_HUGE_VMAP # arch supports the ioremap_pud_enabled() and ioremap_pmd_enabled() VM APIs
vm/ ioremap_prot : ok | HAVE_IOREMAP_PROT # arch has ioremap_prot()
vm/ numa-memblock : ok | HAVE_MEMBLOCK_NODE_MAP # arch supports NUMA aware memblocks
vm/ PG_uncached : ok | ARCH_USES_PG_UNCACHED # arch supports the PG_uncached page flag
vm/ pmdp_splitting_flush : ok | __HAVE_ARCH_PMDP_SPLITTING_FLUSH # arch supports the pmdp_splitting_flush() VM API
vm/ pte_special : ok | __HAVE_ARCH_PTE_SPECIAL # arch supports the pte_special()/pte_mkspecial() VM APIs
vm/ THP : ok | HAVE_ARCH_TRANSPARENT_HUGEPAGE # arch supports transparent hugepages
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that libcxl is public, let's document it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export the "AFU Error Buffer" via sysfs attribute (afu_err_buf). AFU
error buffer is used by the AFU to report application specific
errors. The contents of this buffer are AFU specific and are intended to
be interpreted by the application interacting with the afu.
Suggested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch updates the DocBook to cover the new AEAD interface
implementation.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It turns out that existing U-Boots will dereference NULL pointers
if the device tree does not have cell-index in the portal nodes.
No patch has yet been merged adding device tree nodes for this binding
(except a dtsi that has not yet been referenced), nor has any driver
yet been merged making use of the binding, so it's not too late to
change the binding in order to keep compatibility with existing
U-Boots.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Currently, the FDT blob needs to be in the same 512 MB region as
the kernel, so that it can be mapped into the kernel virtual memory
space very early on using a minimal set of statically allocated
translation tables.
Now that we have early fixmap support, we can relax this restriction,
by moving the permanent FDT mapping to the fixmap region instead.
This way, the FDT blob may be anywhere in memory.
This also moves the vetting of the FDT to mmu.c, since the early
init code in head.S does not handle mapping of the FDT anymore.
At the same time, fix up some comments in head.S that have gone stale.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch implements tape statistics in the st module via
sysfs. Current no statistics are available for tape I/O and there
is no easy way to reuse the block layer statistics for tape
as tape is a character device and does not have perform I/O in
sector sized chunks (the size of the data written to tape
can change). For tapes we also need extra stats related to
things like tape movement (via other I/O).
There have been multiple end users requesting statistics
including AT&T (and some HP customers who have not given
permission to be named). It is impossible for them
to investigate any issues related to tape performance
in a non-invasive way.
[jejb: eliminate PRId64]
Signed-off-by: Shane Seymour <shane.seymour@hp.com>
Tested-by: Shane Seymour <shane.seymour@hp.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This adds documentation of device tree bindings for the
STM32 timer.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This adds documentation of device tree bindings for the
ARM System timer.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add DT bindings documentation for lpc3220-timer. This timer is
used as clocksource on many NXP platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
instead of returning '1' to indicate error - Dan Carpenter
* New support to expose the EFI System Resource Tables in sysfs, which
provides information for performing firmware updates - Peter Jones
* Documentation cleanup in the EFI handover protocol section which
falsely claimed that 'cmdline_size' needed to be filled out by the
boot loader - Alex Smith
* Align the order of SMBIOS tables in /sys/firmware/efi/systab to match
the way that we do things for ACPI and add documentation to
Documentation/ABI - Jean Delvare
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Twjn
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/efi
Pull EFI changes from Matt Fleming:
- Use idiomatic negative error values in efivar_create_sysfs_entry()
instead of returning '1' to indicate error. (Dan Carpenter)
- Implement new support to expose the EFI System Resource Tables in sysfs,
which provides information for performing firmware updates. (Peter Jones)
- Documentation cleanup in the EFI handover protocol section which
falsely claimed that 'cmdline_size' needed to be filled out by the
boot loader. (Alex Smith)
- Align the order of SMBIOS tables in /sys/firmware/efi/systab to match
the way that we do things for ACPI and add documentation to
Documentation/ABI. (Jean Delvare)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull RCU changes from Paul E. McKenney:
- Initialization/Kconfig updates: hide most Kconfig options from unsuspecting users.
There's now a single high level configuration option:
*
* RCU Subsystem
*
Make expert-level adjustments to RCU configuration (RCU_EXPERT) [N/y/?] (NEW)
Which if answered in the negative, leaves us with a single interactive
configuration option:
Offload RCU callback processing from boot-selected CPUs (RCU_NOCB_CPU) [N/y/?] (NEW)
All the rest of the RCU options are configured automatically.
- Remove all uses of RCU-protected array indexes: replace the
rcu_[access|dereference]_index_check() APIs with READ_ONCE() and rcu_lockdep_assert().
- RCU CPU-hotplug cleanups.
- Updates to Tiny RCU: a race fix and further code shrinkage.
- RCU torture-testing updates: fixes, speedups, cleanups and
documentation updates.
- Miscellaneous fixes.
- Documentation updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Using specific compatible string in binding doc to make the binding
more clear.
It's also used to avoid checkpatch warning in the future like follows:
WARNING: DT compatible string "fsl,imx6sx-usdhc" appears un-documented --
check ./Documentation/devicetree/bindings/
+ { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
total: 0 errors, 1 warnings, 18 lines checked
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMCIF IP on R-Car series has parent clock which can be set several rate,
and it was not implemented on old SH-Mobile series (= SH-Mobile series
parent clock was fixed rate) R-Car series MMCIF can use more high speed
access if it setups parent clock. This patch adds parent clock setup
method. It will be used if DT has "max-frequency", and then, this driver
assumes it is booted on R-Car Gen2 or later SoC. Because SH-Mobile series
(which doesn't boot from DT) and R-Car series (which boots from DT) have
different divider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Silence compiler warning]
Allow to specify in the device-tree that no physical write-protect signal
is connected to a particular instance of a MMC controller. Setting the
property will cause the core will assume that the SD card is always
read-write.
The name for the new property is 'disable-wp' and was chosen based on the
property with the same function from the Synopsys designware mobile storage
host controller DT bindings specification.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the quirks and compatible string in sdhci-of-arasan.c
to support sdhci-arasan4.9a version of controller.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for the ntc thermistor NCPXXWF104 series.
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes, with the exception of the following that
address fall-out from recent v4.1-rc1 changes:
- regression fix related to the big fabric API registration changes
and configfs_depend_item() usage, that required cherry-picking one
of HCH's patches from for-next to address the issue for v4.1 code.
- remaining TCM-USER -v2 related changes to enforce full CDB
passthrough from Andy + Ilias.
Also included is a target_core_pscsi driver fix from Andy that
addresses a long standing issue with a Scsi_Host reference being
leaked on PSCSI device shutdown"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix error path in isert_create_pi_ctx()
target: Use a PASSTHROUGH flag instead of transport_types
target: Move passthrough CDB parsing into a common function
target/user: Only support full command pass-through
target/user: Update example code for new ABI requirements
target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOST
target: Fix se_tpg_tfo->tf_subsys regression + remove tf_subsystem
target: Drop signal_pending checks after interruptible lock acquire
target: Add missing parentheses
target: Fix bidi command handling
target/user: Disallow full passthrough (pass_level=0)
ISCSI: fix minor memory leak
- Fix sysfs attribute initialization in nct6775 and nct6683 drivers
- Do not attempt to auto-detect tmp435 on I2C address 0x37
- Ensure iio channel is of type IIO_VOLTAGE in ntc_thermistor driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cHeh
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Some late hwmon patches, all headed for -stable
- fix sysfs attribute initialization in nct6775 and nct6683 drivers
- do not attempt to auto-detect tmp435 on I2C address 0x37
- ensure iio channel is of type IIO_VOLTAGE in ntc_thermistor driver"
* tag 'hwmon-for-linus-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct6683) Add missing sysfs attribute initialization
hwmon: (nct6775) Add missing sysfs attribute initialization
hwmon: (tmp401) Do not auto-detect chip on I2C address 0x37
hwmon: (ntc_thermistor) Ensure iio channel is of type IIO_VOLTAGE
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-05-28
Here's a set of patches intended for 4.2. The majority of the changes
are on the 802.15.4 side of things rather than Bluetooth related:
- All sorts of cleanups & fixes to ieee802154 and related drivers
- Rework of tx power support in ieee802154 and its drivers
- Support for setting ieee802154 tx power through nl802154
- New IDs for the btusb driver
- Various cleanups & smaller fixes to btusb
- New btrtl driver for Realtec devices
- Fix suspend/resume for Realtek devices
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After much discussion, give up on only passing a subset of SCSI commands
to userspace and pass them all. Based on what pscsi is doing, make sure
to set SCF_SCSI_DATA_CDB for I/O ops, and define attributes identical to
pscsi.
Make hw_block_size configurable via dev param.
Remove mention of command filtering from tcmu-design.txt.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We now require that the userspace handler set a bit if the command is not
handled.
Update calls to tcmu_hdr_get_op for v2.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add the device tree bindings documentation for the QCA IPQ806x
variant of the Synopsys DesignWare MAC.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
[added default values to optional properties]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
David Ahern reported that d63e2e1f3d ("sparc/PCI: Clip bridge windows
to fit in upstream windows") fails to boot on sparc/T5-8:
pci 0000:06:00.0: reg 0x184: can't handle BAR above 4GB (bus address 0x110204000)
The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA
addresses, i.e., bus addresses returned via the DMA API (dma_map_single(),
etc.), while the PCI core assumed dma_addr_t could hold *any* bus address,
including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so
dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so
they don't fit in a dma_addr_t. d63e2e1f3d added new checking that
tripped over this mismatch.
Add pci_bus_addr_t, which is wide enough to hold any PCI bus address,
including both raw BAR values and DMA addresses. This will be 64 bits
on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then
dma_addr_t only needs to be wide enough to hold addresses from the DMA API.
[bhelgaas: changelog, bugzilla, Kconfig to ensure pci_bus_addr_t is at
least as wide as dma_addr_t, documentation]
Fixes: d63e2e1f3d ("sparc/PCI: Clip bridge windows to fit in upstream windows")
Fixes: 23b13bc76f ("PCI: Fail safely if we can't handle BARs larger than 4GB")
Link: http://lkml.kernel.org/r/CAE9FiQU1gJY1LYrxs+ma5LCTEEe4xmtjRG0aXJ9K_Tsu+m9Wuw@mail.gmail.com
Link: http://lkml.kernel.org/r/1427857069-6789-1-git-send-email-yinghai@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96231
Reported-by: David Ahern <david.ahern@oracle.com>
Tested-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
CC: stable@vger.kernel.org # v3.19+
I2C address 0x37 may be used by EEPROMs, which can result in false
positives. Do not attempt to detect a chip at this address.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v4.0+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix dts to match what the Linux kernel expects. This works around
touchscreen problems in 4.1 linux on Nokia n900.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds device-tree bindings for ARM SMMUv3 IOMMU devices.
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
By default, with rcutorture.nreaders equal to -1, rcutorture provisions
N-1 reader kthreads, where N is the number of CPUs. This avoids
rcutorture-induced stalls, but also avoids heavier levels of torture.
This commit therefore allows negative values of rcutorture.nreaders
to specify larger numbers of reader kthreads, so that for example
rcutorture.nreaders=-2 provisions N kthreads and rcutorture.nreaders=-5
provisions N+3 kthreads.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
[ paulmck: Update documentation, as suggested by Josh Triplett. ]
The purpose of this commit is to make it easier to verify that RCU's
combining tree is set up correctly, which is useful to have when making
changes in how that tree is initialized.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
[ paulmck: Fold fix found by Fengguang's 0-day test robot. ]
The CONFIG_RCU_FANOUT_EXACT Kconfig parameter is used primarily (and
perhaps only) by rcutorture to verify that RCU works correctly in specific
rcu_node combining-tree configurations. It therefore does not make
much sense have this as a question to people attempting to configure
their kernels. So this commit creates an rcutree.rcu_fanout_exact=
boot parameter that rcutorture can use, and eliminates the original
CONFIG_RCU_FANOUT_EXACT Kconfig parameter.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
Grace-period scans of the rcu_node combining tree normally
proceed quite quickly, so that it is very difficult to reproduce
races against them. This commit therefore allows grace-period
pre-initialization and cleanup to be artificially slowed down,
increasing race-reproduction probability. A pair of pairs of new
Kconfig parameters are provided, RCU_TORTURE_TEST_SLOW_PREINIT to
enable the slowing down of propagating CPU-hotplug changes up the
combining tree along with RCU_TORTURE_TEST_SLOW_PREINIT_DELAY to
specify the delay in jiffies, and RCU_TORTURE_TEST_SLOW_CLEANUP
to enable the slowing down of the end-of-grace-period cleanup scan
along with RCU_TORTURE_TEST_SLOW_CLEANUP_DELAY to specify the delay
in jiffies. Boot-time parameters named rcutree.gp_preinit_delay and
rcutree.gp_cleanup_delay allow these delays to be specified at boot time.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The current formulation of control dependencies fails on DEC Alpha,
which does not respect dependencies of any kind unless an explicit
memory barrier is provided. This means that the current fomulation of
control dependencies fails on Alpha. This commit therefore creates a
READ_ONCE_CTRL() that has the same overhead on non-Alpha systems, but
causes Alpha to produce the needed ordering. This commit also applies
READ_ONCE_CTRL() to the one known use of control dependencies.
Use of READ_ONCE_CTRL() also has the beneficial effect of adding a bit
of self-documentation to control dependencies.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Make a note stating that repeated calls of rcu_dereference() may not
return the same pointer if update happens while in critical section.
Reported-by: Jeff Haran <jeff.haran@citrix.com>
Signed-off-by: Milos Vyletel <milos@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
This commit provides another caveat for the care and feeding of pointers
returned by rcu_dereference() that was pointed out in discussions within
the C++ standards committee.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Our current documentation claims that, when followed by an ACQUIRE,
smp_mb__before_spinlock() orders prior loads against subsequent loads
and stores, which isn't the intent. This commit therefore fixes the
documentation to state that this sequence orders only prior stores
against subsequent loads and stores.
In addition, the original intent of smp_mb__before_spinlock() was to only
order prior loads against subsequent stores, however, people have started
using it as if it ordered prior loads against subsequent loads and stores.
This commit therefore also updates smp_mb__before_spinlock()'s header
comment to reflect this new reality.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Pull x86 fixes from Ingo Molnar:
"This tree includes:
- a fix that disables the compacted FPU XSAVE format by disabling
XSAVES support: the fixes are too complex and the breakages
ABI-affecting, so we want this to be quirked off in a robust way
and backported, to make sure no broken kernel is exposed to the new
hardware (which exposure is still very limited).
- an MCE printk message fix
- a documentation fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Disable XSAVES* support for now
x86/Documentation: Update the contact email for L3 cache index disable functionality
x86/mce: Fix MCE severity messages
The commit df59fa7f4b "spi: orion: support armada extended baud
rates" made the assumptions that all the Armada SoCs supported the
same maximum frequency. However, according the hardware datasheet, the
maximum frequency supported by the Armada 370 SoC is tclk/4, for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
This patch introduces new compatible strings to handle all these
case. In order to be future proof a compatible was created for each
SoC even if currently some SoCs seem using the same IP.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A long standing problem on busy servers is the tiny available TCP port
range (/proc/sys/net/ipv4/ip_local_port_range) and the default
sequential allocation of source ports in connect() system call.
If a host is having a lot of active TCP sessions, chances are
very high that all ports are in use by at least one flow,
and subsequent bind(0) attempts fail, or have to scan a big portion of
space to find a slot.
In this patch, I changed the starting point in __inet_hash_connect()
so that we try to favor even [1] ports, leaving odd ports for bind()
users.
We still perform a sequential search, so there is no guarantee, but
if connect() targets are very different, end result is we leave
more ports available to bind(), and we spread them all over the range,
lowering time for both connect() and bind() to find a slot.
This strategy only works well if /proc/sys/net/ipv4/ip_local_port_range
is even, ie if start/end values have different parity.
Therefore, default /proc/sys/net/ipv4/ip_local_port_range was changed to
32768 - 60999 (instead of 32768 - 61000)
There is no change on security aspects here, only some poor hashing
schemes could be eventually impacted by this change.
[1] : The odd/even property depends on ip_local_port_range values parity
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not clear right now that the order in which entries are displayed
in /sys/firmware/efi/systab actually forms an ABI that userspace tools
rely upon.
Document the ABI along with the userspace tool that cares.
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@globallogic.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The documentation on cpu topology seems to be a bit out-of-date.
It doesn't mention the **_siblings_list attributes and uses old
names for topology_**_cpumask() macros.
Add information on missing attributes plus some additional
clarifications.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: http://lkml.kernel.org/r/1432645896-12588-3-git-send-email-bgolaszewski@baylibre.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As part of the effort to phase out MTRR use document
write-combining MTRR effects on pages with different non-PAT
page attributes flags and different PAT entry values. Extend
arch_phys_wc_add() documentation to clarify power of two sizes /
boundary requirements as we phase out mtrr_add() use.
Lastly hint towards ioremap_uc() for corner cases on device
drivers working with devices with mixed regions where MTRR size
requirements would otherwise not enable write-combining
effective memory types.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ville Syrjälä <syrjala@sci.fi>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: linux-fbdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1430343851-967-3-git-send-email-mcgrof@do-not-panic.com
Link: http://lkml.kernel.org/r/1432628901-18044-10-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Hold it down for future reference, as the question about the
question mark in stack traces keeps popping up.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/1432628901-18044-18-git-send-email-bp@alien8.de
Link: http://lkml.kernel.org/r/20150521101614.GA10889@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Update the documentation after
6f442be2fb ("x86_64, traps: Stop using IST for #SS").
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/1432628901-18044-17-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
... to Documentation/x86/ as it is going to collect more and not
only 64-bit specific info.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/1432628901-18044-16-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds support for the SSD1305 OLED controller.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The 130X controllers are very similar from the configuration point of view.
The configuration registers for the SSD1305/6/7 are bit identical (except the
the VHCOM register and the the default values for clock setup register). This
patch unifies the init code of the controller and adds hardware specific
properties to DT that are needed to correctly initialize the device.
The SSD130X can be wired to the OLED panel in various ways. Even for the
same controller this wiring can differ from one display module to another
and can not be probed by software. The added DT properties reflect these
hardware decisions of the display module manufacturer.
The 'com-sequential', 'com-lrremap' and 'com-invdir' values define different
possibilities for the COM signals pin configuration and readout direction
of the video memory. The 'segment-no-remap' allows the inversion of the
memory-to-pin mapping ultimately inverting the order of the controllers
output pins. The 'prechargepX' values need to be adapted according to the
capacitance of the OLEDs pixel cells.
So far these hardware specific bits are hard coded in the init code, making
the driver usable only for one certain wiring of the controller. This patch
makes the driver usable with all possible hardware setups, given a valid hw
description in DT. If these values are not set in DT the default values,
as they are set in the ssd1307 init code right now, are used. This implies
that without the corresponding DT property "segment-no-remap" the segment
remap of the ssd130X controller gets activated. Even though this is not the
default behaviour according to the datasheet it maintains backward
compatibility with older DTBs.
Note that the SSD1306 does not seem to be using the configuration written to
the registers at all. Therefore this patch does not try to maintain these
values without changes in DT. For reference an example is added to the DT
bindings documentation that reproduces the configuration that is set in the
current init code.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Tested-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds the solomon prefix for Solomon Systech Limited.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A few late important fixes which have been pending
on mailing list due to my vacations.
The important fixes are a fix for DEPCMD and DGCMD
status bitfields on DWC3, a couple fixes for Renesas
USB Controller, one of which prevents a broken DT
binding from reaching v4.1-final, and an old fix for
s3c2410-udc where pullup logic was reversed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gNa5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.1-rc5
A few late important fixes which have been pending
on mailing list due to my vacations.
The important fixes are a fix for DEPCMD and DGCMD
status bitfields on DWC3, a couple fixes for Renesas
USB Controller, one of which prevents a broken DT
binding from reaching v4.1-final, and an old fix for
s3c2410-udc where pullup logic was reversed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Update the linux-zigbee git:// repository URL.
* Remove the MLME section as the current kernel does not provide a
full 802.15.4 MLME implementation.
* The hardmac example driver 'fakehard' was removed some time ago.
* The IEEE 802.15.4 device drivers live in drivers/net/ieee802154/,
not in drivers/ieee802154/.
* The IEEE 802.15.4 MTU is 127 bytes, not 128 bytes.
* Some of the 6LoWPAN code lives in net/6lowpan/.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Based on the datasheet found here:
http://www.ti.com/lit/ds/symlink/bq24257.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the pktgen samples script pktgen_sample02_multiqueue.sh that
demonstrates generating packets on multiqueue NICs.
Specifically notice the options "-t" that specifies how many
kernel threads to activate. Also notice the flag QUEUE_MAP_CPU,
which cause the SKB TX queue to be mapped to the CPU running the
kernel thread. For best scalability people are also encourage to
map NIC IRQ /proc/irq/*/smp_affinity to CPU number.
Usage example with "-t" 4 threads and help:
./pktgen_sample02_multiqueue.sh -i eth4 -m 00:1B:21:3C:9D:F8 -t 4
Usage: ./pktgen_sample02_multiqueue.sh [-vx] -i ethX
-i : ($DEV) output interface/device (required)
-s : ($PKT_SIZE) packet size
-d : ($DEST_IP) destination IP
-m : ($DST_MAC) destination MAC-addr
-t : ($THREADS) threads to start
-c : ($SKB_CLONE) SKB clones send before alloc new SKB
-b : ($BURST) HW level bursting of SKBs
-v : ($VERBOSE) verbose
-x : ($DEBUG) debug
Removing pktgen.conf-2-1 and pktgen.conf-2-2 as these examples
should be covered now.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the first basic pktgen samples script pktgen_sample01_simple.sh,
which demonstrates the a simple use of the helper functions.
Removing pktgen.conf-1-1 as that example should be covered now.
The naming scheme pktgen_sampleNN, where NN is a number, should encourage
reading the samples in a specific order.
Script cause pktgen sending with a single thread and single interface,
and introduce flow variation via random UDP source port.
Usage example and help:
./pktgen_sample01_simple.sh -i eth4 -m 00:1B:21:3C:9D:F8 -d 192.168.8.2
Usage: ./pktgen_sample01_simple.sh [-vx] -i ethX
-i : ($DEV) output interface/device (required)
-s : ($PKT_SIZE) packet size
-d : ($DEST_IP) destination IP
-m : ($DST_MAC) destination MAC-addr
-c : ($SKB_CLONE) SKB clones send before alloc new SKB
-v : ($VERBOSE) verbose
-x : ($DEBUG) debug
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pktgen.txt documentation still claimed that adding same device to
multiple threads were not supported, but it have been since 2008 via
commit e6fce5b916 ("pktgen: multiqueue etc.").
Document this and describe the naming scheme dev@X, as the procfile name
still need to be unique.
Fixes: e6fce5b916 ("pktgen: multiqueue etc.")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pktgen.txt documentation over available config options were not complete.
Making the list complete by adding the following.
Pgcontrol commands:
reset
Device commands:
burst
queue_map_min
queue_map_max
skb_priority
tos
traffic_class
node
spi
dst6_max
dst6_min
vlan_cfi
vlan_id
vlan_p
svlan_cfi
svlan_id
svlan_p
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And cleanup some whitespaces in pktgen.txt.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearly specify that "Cc: stable@vger.kernel.org" is strongly preferred so
that developers understand that the other options should only be used when
absolutely required.
Also specify how upstream commit ids should be referenced in patches
submitted directly to stable (I gathered this from looking at the stable
archives), and specify that any modified patches for stable should be
clearly documented in the patch description.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Also remove spaces before TABs while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
MAX8973 supports the voltage output enable/disable through its EN
pin. This EN pin can be connected through GPIO from host processor.
Add support to provide GPIO number from platform/DT and if it is
valid GPIO then enable external control default.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some platform specific parameter required to configure
the device like enable external control, DVS gpio etc.
Add DT parsing of such properties to make platform specific data.
Update DT binding doc accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the recent update of the kernel crypto API header files,
locations of function definitions and their documentation have changed.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
and on x86. The rest is fixes for bugs with newer Intel
processors.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVXGLvAAoJEL/70l94x66DxOAH/270hZu3Rt0Tt04LYs0uy1B3
6a91Hs4YsYALe0j6IVZUQ2ngO+N4DPsw/Lusutd82jWX13UG221w1rbUtUpNF46r
bPf7Eh4AdGhNehGtkllRKrBmZEDkZVngZWsftFvzA+rmbV/HVzFU5SfuPdhzYAL5
WpQTzou0w63c3Gh6hymLsq/x/zUScMRoFdyjIEJTRN+AOnnro9I/nj4O83OEF8uv
Hp4VZ7TDG55xTloiC5WSimTCWPIZFDMiuim1iFo/OOOIGjfjdM8IBKwer4zIXa/S
VD71lYu267yxIabYpbEOjd+dcZ5myJhy4ePWmWHZczsOeklbvMouWMD7/1U2Gpg=
=x0LU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"This includes a fix for two oopses, one on PPC and on x86.
The rest is fixes for bugs with newer Intel processors"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm/fpu: Enable eager restore kvm FPU for MPX
Revert "KVM: x86: drop fpu_activate hook"
kvm: fix crash in kvm_vcpu_reload_apic_access_page
KVM: MMU: fix SMAP virtualization
KVM: MMU: fix CR4.SMEP=1, CR0.WP=0 with shadow pages
KVM: MMU: fix smap permission check
KVM: PPC: Book3S HV: Fix list traversal in error case
DT nodes should use the more specific adi,adxl345 and adi,adxl346
compatible values instead. As the ADXL346 is backward-compatible with
the ADXL345, ADXL346 nodes must list both adi,adxl346 and adi,adxl345,
in that order.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
exception of a single locking fix in the core code. All driver fixes are
for code that was merged recently. The Samsung stuff is mostly fixes
around suspend/resume, the Qualcomm fixes are for invalid hardware
configuration data and the Silicon Labs patches are fixes following
their move away from platform_data to Device Tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yjsw
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"The first set of clk fixes for 4.1 are all driver bugs, with the
exception of a single locking fix in the core code.
All driver fixes are for code that was merged recently. The Samsung
stuff is mostly fixes around suspend/resume, the Qualcomm fixes are
for invalid hardware configuration data and the Silicon Labs patches
are fixes following their move away from platform_data to Device Tree"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: si5351: Do not pass struct clk in platform_data
clk: si5351: Mention clock-names in the binding documentation
clk: add missing lock when call clk_core_enable in clk_set_parent
clk: exynos5420: Restore GATE_BUS_TOP on suspend
clk: qcom: Fix MSM8916 gfx3d_clk_src configuration
clk: qcom: Fix MSM8916 venus divider value
clk: exynos5433: Fix wrong PMS value of exynos5433_pll_rates
clk: exynos5433: Fix wrong parent clock of sclk_apollo clock
clk: exynos5433: Fix CLK_PCLK_MONOTONIC_CNT clk register assignment
clk: exynos5433: Fix wrong offset of PCLK_MSCL_SECURE_SMMU_JPEG
clk: Use CONFIG_ARCH_EXYNOS instead of CONFIG_ARCH_EXYNOS5433
USP is a general purpose serial port in SiRFSoC, which can work as SPI.
the most data flow of USP and pure SPI is same with main differences
in registers layout.
this patch moves registers layout to private data, and use flags to
differentiate other minor differences between prima2-spi, prima2-usp
and atlas7-usp for hardware configuration.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Conflicts:
arch/x86/kernel/i387.c
This commit is conflicting:
e88221c50c ("x86/fpu: Disable XSAVES* support for now")
These functions changed a lot, move the quirk to arch/x86/kernel/fpu/init.c's
fpu__init_system_xstate_size_legacy().
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This work as a follow-up of commit f7b3bec6f5 ("net: allow setting ecn
via routing table") and adds RFC3168 section 6.1.1.1. fallback for outgoing
ECN connections. In other words, this work adds a retry with a non-ECN
setup SYN packet, as suggested from the RFC on the first timeout:
[...] A host that receives no reply to an ECN-setup SYN within the
normal SYN retransmission timeout interval MAY resend the SYN and
any subsequent SYN retransmissions with CWR and ECE cleared. [...]
Schematic client-side view when assuming the server is in tcp_ecn=2 mode,
that is, Linux default since 2009 via commit 255cac91c3 ("tcp: extend
ECN sysctl to allow server-side only ECN"):
1) Normal ECN-capable path:
SYN ECE CWR ----->
<----- SYN ACK ECE
ACK ----->
2) Path with broken middlebox, when client has fallback:
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ----->
<----- SYN ACK
ACK ----->
In case we would not have the fallback implemented, the middlebox drop
point would basically end up as:
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
In any case, it's rather a smaller percentage of sites where there would
occur such additional setup latency: it was found in end of 2014 that ~56%
of IPv4 and 65% of IPv6 servers of Alexa 1 million list would negotiate
ECN (aka tcp_ecn=2 default), 0.42% of these webservers will fail to connect
when trying to negotiate with ECN (tcp_ecn=1) due to timeouts, which the
fallback would mitigate with a slight latency trade-off. Recent related
paper on this topic:
Brian Trammell, Mirja Kühlewind, Damiano Boppart, Iain Learmonth,
Gorry Fairhurst, and Richard Scheffenegger:
"Enabling Internet-Wide Deployment of Explicit Congestion Notification."
Proc. PAM 2015, New York.
http://ecn.ethz.ch/ecn-pam15.pdf
Thus, when net.ipv4.tcp_ecn=1 is being set, the patch will perform RFC3168,
section 6.1.1.1. fallback on timeout. For users explicitly not wanting this
which can be in DC use case, we add a net.ipv4.tcp_ecn_fallback knob that
allows for disabling the fallback.
tp->ecn_flags are not being cleared in tcp_ecn_clear_syn() on output, but
rather we let tcp_ecn_rcv_synack() take that over on input path in case a
SYN ACK ECE was delayed. Thus a spurious SYN retransmission will not prevent
ECN being negotiated eventually in that case.
Reference: https://www.ietf.org/proceedings/92/slides/slides-92-iccrg-1.pdf
Reference: https://www.ietf.org/proceedings/89/slides/slides-89-tsvarea-1.pdf
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mirja Kühlewind <mirja.kuehlewind@tik.ee.ethz.ch>
Signed-off-by: Brian Trammell <trammell@tik.ee.ethz.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Dave That <dave.taht@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KVM may turn a user page to a kernel page when kernel writes a readonly
user page if CR0.WP = 1. This shadow page entry will be reused after
SMAP is enabled so that kernel is allowed to access this user page
Fix it by setting SMAP && !CR0.WP into shadow page's role and reset mmu
once CR4.SMAP is updated
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Pinctrl module (ioc) controls the Pad's function select
(each pad can have 8 functions), Pad's Drive Strength, Pad's
Pull Select and Pad's Input Disable status.
The ioc has two modules, ioc_top & ioc_rtc. Both of these two
modules have function select/clear, Pull select and Drive
Strength registers. But only ioc_rtc has input-disable
registers. The Pads on ioc_top have to access ioc_rtc to set
their input-disable status and intpu-disable-value.
So have to use one ioc driver instance to drive these two
ioc modules at the same time, and each ioc module will be
treat as one bank on the "IOC Device".
The GPIO Controller controls the GPIO status if the Pad has
been config as GPIO by Pinctrl already. Includes the GPIO
Input/output, Interrupt type, Interrupt Status, and Set/Get
Values.
The GPIO pull up/down are controlled by Pinctrl.
There are 7 GPIO Groups and splited into 3 MACROs in atlas7.
The GPIO Groups in one MACRO share one GPIO controllers, each
GPIO Group are treated as one GPIO bank.
For example:
In VDIFM macro, there is one GPIO Controller, it has 3 banks
to control 3 gpio groups. Its gpio name space is from 0 to 95.
The Device Tree can be written as following:
gpio-ranges = <&pinctrl 0 0 0>,
<&pinctrl 32 0 0>,
<&pinctrl 64 0 0>;
gpio-ranges-group-names = "gnss_gpio_grp",
"lcd_vip_gpio_grp",
"sdio_i2s_gpio_grp";
bank#0 is from 0~31, the pins are from pinctrl's "gnss_gpio_grp".
bank#2 is from 32~63, the pins are from pinctrl's "lcd_vip_gpio_grp".
bank#3 is from 64~95, the pins are from pinctrl's "sdio_i2s_gpio_grp".
Signed-off-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since 6397 is no need to support interrupt controller,
moving interrupt controller relate property to optional list.
Also adding mt8173 and mt8127 to bindings.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clarify what is the relationship between tasks' parameters and scheduling
parameters, explaining how to set the scheduling parameters so that all the
absolute deadlines of a task are respected.
Signed-off-by: Luca Abeni <luca.abeni@unitn.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: henrik@austad.us
Cc: juri.lelli@gmail.com
Cc: raistlin@linux.it
Link: http://lkml.kernel.org/r/1431954032-16473-9-git-send-email-luca.abeni@unitn.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a description of the Dhall's effect, some discussion about
schedulability tests for global EDF, and references to real-time
literature.
Signed-off-by: Luca Abeni <luca.abeni@unitn.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: henrik@austad.us
Cc: juri.lelli@gmail.com
Cc: raistlin@linux.it
Link: http://lkml.kernel.org/r/1431954032-16473-8-git-send-email-luca.abeni@unitn.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add a short discussion about sufficient and necessary schedulability tests,
and add a simple example showing that if D_i != P_i then density based tests
are only sufficient.
Also add some references to scientific papers on schedulability tests for
EDF that are both necessary and sufficient, and on their computational
complexity.
Signed-off-by: Luca Abeni <luca.abeni@unitn.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: henrik@austad.us
Cc: juri.lelli@gmail.com
Cc: raistlin@linux.it
Link: http://lkml.kernel.org/r/1431954032-16473-7-git-send-email-luca.abeni@unitn.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The "_i" index is used in this document to to denote a particular task,
so "sum_i", "max_i" and "min_i" might be confusing.
Signed-off-by: Luca Abeni <luca.abeni@unitn.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: henrik@austad.us
Cc: juri.lelli@gmail.com
Cc: raistlin@linux.it
Link: http://lkml.kernel.org/r/1431954032-16473-6-git-send-email-luca.abeni@unitn.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This file previously mixed American and British English; switch to American
for consistency.
Signed-off-by: Luca Abeni <luca.abeni@unitn.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: henrik@austad.us
Cc: juri.lelli@gmail.com
Cc: raistlin@linux.it
Link: http://lkml.kernel.org/r/1431954032-16473-3-git-send-email-luca.abeni@unitn.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
C_i/min{D_i,T_i}, where T_i is not referred before, should be
substituted with C_i/min{D_i,P_i}.
Signed-off-by: Zhiqiang Zhang <zhangzhiqiang.zhang@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: henrik@austad.us
Cc: juri.lelli@gmail.com
Cc: raistlin@linux.it
Link: http://lkml.kernel.org/r/1431954032-16473-2-git-send-email-luca.abeni@unitn.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since set_mb() is really about an smp_mb() -- not a IO/DMA barrier
like mb() rename it to match the recent smp_load_acquire() and
smp_store_release().
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* readtest: the signal-handling code was clobbering the error codes we should
be handling/reporting in this test, rendering it useless. Noticed by Coverity.
* the common SPI NOR flash DT binding (merged for 4.1-rc1) is being revised,
so let's change that before 4.1 is minted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=13mb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two MTD fixes for 4.1:
- readtest: the signal-handling code was clobbering the error codes
we should be handling/reporting in this test, rendering it useless.
Noticed by Coverity.
- the common SPI NOR flash DT binding (merged for 4.1-rc1) is being
revised, so let's change that before 4.1 is minted"
* tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd:
Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"
mtd: readtest: don't clobber error reports
OSA Ethernet hardware is introducing BRIDGEPORT functionality
similar (but not identical) to HiperSockets BRIDGEPORT. This
patch makes HiperSockets BRIDGEPORT related sysfs attributes
and udev events work with OSA hardware too.
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
