Trivial fix to spelling mistake in mfc_err error messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Further investigation revealed that codec buffers also don't need to
be allocated at higher addresses than firmware base for MFC v6+ hardware.
Those buffers can be quite large and its size depends on the selected
format and framesize. This patch changes the way the codec buffers are
allocated - driver will use generic allocator for them instead of the
pre-allocated buffer for firmware and contexts.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clock should be turned off after calling s5p_mfc_init_hw() from the
watchdog worker, like it is already done in the s5p_mfc_open() which also
calls this function.
Fixes: af93574678 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation for MFC hardware still uses 'left' and 'right' names for
the memory channel/banks, so replace BANK1/2 defines with more appropriate
BANK_L/R names.
Suggested-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It turned out that all versions of MFC v6+ hardware doesn't have a strict
requirement for ALL buffers to be allocated on higher addresses than the
firmware base like it was documented for MFC v5. This requirement is true
only for the device and per-context buffers. All video data buffers can be
allocated anywhere for all MFC v6+ versions. Basing on this fact, the
special DMA configuration based on two reserved memory regions is not
really needed for MFC v6+ devices, because the memory requirements for the
firmware, device and per-context buffers can be fulfilled by the simple
probe-time pre-allocated block allocator introduced in previous patch.
This patch enables support for such pre-allocated block based allocator
always for MFC v6+ devices. Due to the limitations of the memory management
subsystem the largest supported size of the pre-allocated buffer when no
CMA (Contiguous Memory Allocator) is enabled is 4 MiB.
This patch also removes the requirement to provide two reserved memory
regions for MFC v6+ devices in device tree. Now the driver is fully
functional without them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The main reason for using special configuration of IOMMU domain was the
problem with MFC firmware, which failed to operate properly when placed
at 0 DMA address. Instead of adding custom code for configuring each
variant of IOMMU domain and architecture specific glue code, simply use
what arch code provides and if the DMA base address equals zero, skip
first 128 KiB to keep required alignment. This patch also make the driver
operational on ARM64 architecture, because it no longer depends on ARM
specific DMA-mapping and IOMMU glue code functions.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Current MFC driver depends on the fact that when IOMMU is available, the
DMA-mapping framework and its IOMMU glue will use first-fit allocator.
This was true for ARM architecture, but its not for ARM64 arch. However, in
case of MFC v6+ hardware and latest firmware, it turned out that there is
no strict requirement for ALL buffers to be allocated on higher addresses
than the firmware base. This requirement is true only for the device and
per-context buffers. All video data buffers can be allocated anywhere for
all MFC v6+ versions.
Such relaxed requirements for the memory buffers can be easily fulfilled
by allocating firmware, device and per-context buffers from the probe-time
preallocated larger buffer. This patch adds support for it. This way the
driver finally works fine on ARM64 architecture. The size of the
preallocated buffer is 8 MiB, what is enough for three instances H264
decoders or encoders (other codecs have smaller memory requirements).
If one needs more for particular use case, one can use "mem" module
parameter to force larger (or smaller) buffer (for example by adding
"s5p_mfc.mem=16M" to kernel command line).
[mchehab@s-opensource.com: fix two checkpatch warnings: don't initialize
static to NULL; don't use S_foo permisions]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move code for DMA memory configuration with IOMMU into separate function
to make it easier to compare what is being done in each case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Firmware for MFC v6+ variants is not larger than 400 KiB, so there is no
need to allocate a full 1 MiB buffer for it. Reduce it to 512 KiB to keep
proper alignment of allocated buffer.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Once firmware buffer has been converted to use s5p_mfc_priv_buf structure,
it is possible to allocate it with existing s5p_mfc_alloc_priv_buf()
function. This change will help to reduce code variants in the next
patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To complete DMA memory configuration for MFC device, allocation of the
firmware buffer is needed, because some parameters are dependant on its base
address. Till now, this has been handled in the s5p_mfc_alloc_firmware()
function. This patch moves that logic to s5p_mfc_configure_dma_memory() to
keep DMA memory related operations in a single place. This way
s5p_mfc_alloc_firmware() is simplified and does what it name says. The
other consequence of this change is moving s5p_mfc_alloc_firmware() call
from the s5p_mfc_probe() function to the s5p_mfc_configure_dma_memory().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use s5p_mfc_priv_buf structure for keeping the firmware image. This will
help handling of firmware buffer allocation in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Setting DMA max segment size to 32 bit mask is a part of DMA memory
configuration, so move those calls to s5p_mfc_configure_dma_memory()
function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change parameters for s5p_mfc_alloc_priv_buf() and s5p_mfc_release_priv_buf()
functions. Instead of DMA device pointer and a base, provide common MFC
device structure and memory bank context identifier.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal MFC driver device structure contains two entries for keeping
addresses of the DMA memory banks. Replace them with the dma_base[] array
and use defines for accessing particular banks. This will help to simplify
code in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Internal MFC driver device structure contains two pointers to devices used
for DMA memory allocation: mem_dev_l and mem_dev_r. Replace them with the
mem_dev[] array and use defines for accessing particular banks. This will
help to simplify code in the next patches.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unused structures, definitions and functions
that are no longer called from the driver code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Reviewed-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Interrupt routine must wake process waiting for given interrupt AFTER
updating driver's internal structures and contexts. Doing it in-between
is a serious bug. This patch moves all calls to the wake() function to
the end of the interrupt processing block to avoid potential and real
races, especially on multi-core platforms. This also fixes following issue
reported from clock core (clocks were disabled in interrupt after being
unprepared from the other place in the driver, the stack trace however
points to the different place than s5p_mfc driver because of the race):
WARNING: CPU: 1 PID: 18 at drivers/clk/clk.c:544 clk_core_unprepare+0xc8/0x108
Modules linked in:
CPU: 1 PID: 18 Comm: kworker/1:0 Not tainted 4.10.0-next-20170223-00070-g04e18bc99ab9-dirty #2154
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: pm pm_runtime_work
[<c010d8b0>] (unwind_backtrace) from [<c010a534>] (show_stack+0x10/0x14)
[<c010a534>] (show_stack) from [<c033292c>] (dump_stack+0x74/0x94)
[<c033292c>] (dump_stack) from [<c011cef4>] (__warn+0xd4/0x100)
[<c011cef4>] (__warn) from [<c011cf40>] (warn_slowpath_null+0x20/0x28)
[<c011cf40>] (warn_slowpath_null) from [<c0387a84>] (clk_core_unprepare+0xc8/0x108)
[<c0387a84>] (clk_core_unprepare) from [<c0389d84>] (clk_unprepare+0x24/0x2c)
[<c0389d84>] (clk_unprepare) from [<c03d4660>] (exynos_sysmmu_suspend+0x48/0x60)
[<c03d4660>] (exynos_sysmmu_suspend) from [<c042b9b0>] (pm_generic_runtime_suspend+0x2c/0x38)
[<c042b9b0>] (pm_generic_runtime_suspend) from [<c0437580>] (genpd_runtime_suspend+0x94/0x220)
[<c0437580>] (genpd_runtime_suspend) from [<c042e240>] (__rpm_callback+0x134/0x208)
[<c042e240>] (__rpm_callback) from [<c042e334>] (rpm_callback+0x20/0x80)
[<c042e334>] (rpm_callback) from [<c042d3b8>] (rpm_suspend+0xdc/0x458)
[<c042d3b8>] (rpm_suspend) from [<c042ea24>] (pm_runtime_work+0x80/0x90)
[<c042ea24>] (pm_runtime_work) from [<c01322c4>] (process_one_work+0x120/0x318)
[<c01322c4>] (process_one_work) from [<c0132520>] (worker_thread+0x2c/0x4ac)
[<c0132520>] (worker_thread) from [<c0137ab0>] (kthread+0xfc/0x134)
[<c0137ab0>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
---[ end trace 1ead49a7bb83f0d8 ]---
Fixes: af93574678 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org # v4.5+
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix s5p_mfc_set_dec_frame_buffer_v6() to print buffer pointer in hex
to be consistent with the rest of the messages in the routine.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialize members of the internal device and context structures as early
as possible to avoid access to uninitialized objects on initialization
failures. If loading firmware or creating of the hardware instance fails,
driver will access device or context queue in error handling path, which
might not be initialized yet, what causes kernel panic. Fix this by moving
initialization of all static members as early as possible.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Exynos5433 SoC has MFC v8 hardware module, but it has more
complex clock hierarchy, so a new compatible is added.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch changes the code for handling clocks. Now clocks are defined
per each device variant, what is a preparation for adding support for
Exynos 5433 MFC V8, which has more clocks than all previous versions.
Also use devm_clk_get() to simplify cleanup path.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch moves preparation of clocks from s5p_mfc_init_pm()
(driver probe) to s5p_mfc_power_on() (start of device operation).
This change will allow to use runtime power usage optimization
on newer Samsung Exynos platforms (for example Exynos 5433).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After commit "s5p-mfc: Fix clock management in s5p_mfc_release function"
all clocks related functions are called only when MFC device is really
available, so there is no additional check needed for NULL
gate clocks. This patch simplifies the code and kills IS_ERR_OR_NULL
macro usage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CONFIG_PM is always enabled on Exynos platforms, so remove dead code
related to early development of MFC driver on platform without PM support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move clock disabling before turning power off. This will enable later
to add calls to clk_prepare/unprepare in the s5p_mfc_power_off() function
to avoid keeping clocks prepared all the time when driver is bound.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The maximum rate of special clock depends on SoC variant and should
be set in device tree via assigned-clock-rates property, so remove
the code which forces special clock to 200MHz.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some applications don't check error codes from QBUF/DQBUF ioctls,
so don't spam kernel log with errors if they fall into endless loop
trying to queue next buffer after a failure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We do video allocation all the time and we need it to be fast. Plus TLB
efficiency isn't terribly important for video.
That means we want to set DMA_ATTR_ALLOC_SINGLE_PAGES.
See also the previous change (commit 14d3ae2efe "ARM: dma-mapping: Use
DMA_ATTR_ALLOC_SINGLE_PAGES hint to optimize allocation").
[m.szyprowski: rebased patch onto v4.9-rc1 and adapted changes
to latest videbuf2 changes, this simplifies code changes to
only set proper dma attribute flag and comment the reason
for it, added commit id of arch/arm/mm patch]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Clock control indirectly requires access to MFC device, so call it only
if we are sure that the device exists in s5p_mfc_release function.
s5p_mfc_remove() calls s5p_mfc_final_pm(), which releases all PM related
resources, including clocks, so any call to clocks related functions
is not valid after s5p_mfc_final_pm().
Fixes: d695c12 ("[media] media: s5p-mfc fix invalid memory access from
s5p_mfc_release()")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Newer MFC hardware have internal clock gating feature, so additional
software-triggered clock gating sometimes causes misbehavior of the MFC
firmware and results in freeze or crash. This patch changes the driver
to use software-triggered clock gating only when working with v5 MFC
hardware, where it has been proven to work properly.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, when incomplete frame is received in the middle of
decoding, driver treats it as an error, so src/dst queue and
clock are cleaned. Although it is obviously error case, it is
needed to maintain video decoding in case of necessity. This
patch supports skip incomplete frame to next.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver complains about too small scratch buffer size. After adjusting
it according to vendor code, decoding works.
[mszyprow: moved the change to the header file]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Include buffer size in s5p_mfc_alloc_priv_buf() the error message
when it fails to allocate the buffer.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
s5p_mfc_alloc_priv_buf() prints two message to report invalid memory
configuration error. Collapse them into a single message.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
alloc_workqueue replaces deprecated create_singlethread_workqueue().
The MFC device driver is a v4l2 driver which can encode/decode video
raw/elementary streams and has support for all popular video codecs.
The driver's watchdog_workqueue has been replaced with system_wq since
it queues a single work item, &dev->watchdog_work, which calls for no
ordering requirement. The work item is involved in running the watchdog
timer and is not being used on a memory reclaim path.
Work item has been flushed in s5p_mfc_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Stop using alloc_ctx and just fill in the device pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the V4L2 documentation the driver and card fields should be
used to identify the driver and the device but the s5p-mfc driver fills
those field using the platform device name, which in turn is the name of
the device DT node.
So not only the filled information isn't correct but also the same values
are used in all the fields for both the encoder and decoder video devices.
Before this patch:
Driver Info (not using libv4l2):
Driver name : 11000000.codec
Card type : 11000000.codec
Bus info : platform:11000000.codec
Driver version: 4.7.0
Driver Info (not using libv4l2):
Driver name : 11000000.codec
Card type : 11000000.codec
Bus info : platform:11000000.codec
Driver version: 4.7.0
After this patch:
Driver Info (not using libv4l2):
Driver name : s5p-mfc
Card type : s5p-mfc-dec
Bus info : platform:11000000.codec
Driver version: 4.7.0
Driver Info (not using libv4l2):
Driver name : s5p-mfc
Card type : s5p-mfc-enc
Bus info : platform:11000000.codec
Driver version: 4.7.0
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
