* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (29 commits)
MIPS: Call oops_enter, oops_exit in die
staging/octeon: Software should check the checksum of no tcp/udp packets
MIPS: Octeon: Enable C0_UserLocal probing.
MIPS: No branches in delay slots for huge pages in handle_tlbl
MIPS: Don't clobber CP0_STATUS value for CONFIG_MIPS_MT_SMTC
MIPS: Octeon: Select CONFIG_HOLES_IN_ZONE
MIPS: PM: Use struct syscore_ops instead of sysdevs for PM (v2)
MIPS: Compat: Use 32-bit wrapper for compat_sys_futex.
MIPS: Do not use EXTRA_CFLAGS
MIPS: Alchemy: DB1200: Disable cascade IRQ in handler
SERIAL: Lantiq: Set timeout in uart_port
MIPS: Lantiq: Fix setting the PCI bus speed on AR9
MIPS: Lantiq: Fix external interrupt sources
MIPS: tlbex: Fix build error in R3000 code.
MIPS: Alchemy: Include Au1100 in PM code.
MIPS: Alchemy: Fix typo in MAC0 registration
MIPS: MSP71xx: Fix build error.
MIPS: Handle __put_user() sleeping.
MIPS: Allow forced irq threading
MIPS: i8259: Mark cascade interrupt non-threaded
...
Icmp packets with wrong checksum are never dropped since skb->ip_summed is
set to CHECKSUM_UNNECESSARY.
When icmp packets with wrong checksum pass through the octeon net driver,
the not_IP, IP_exc, L4_error hardware indicators show no error. so the
driver sets CHECKSUM_UNNECESSARY on skb->ip_summed.
L4_error only works for TCP/UDP, not for ICMP.
Signed-off-by: Roy.Li <rongqing.li@windriver.com>
To: linux-mips@linux-mips.org
Cc: netdev@vger.kernel.org
Cc: ralf@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2798/
Acked-by: David Daney <david.daney@cavium.com>
Cc: Greg KH <greg@kroah.com
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After commit c5f5c4db39 ("staging: zcache: fix crash on high memory
swap") cleancache crashes on the first successful get. This was caused
by a remaining virt_to_page() call in zcache_pampd_get_data_and_free()
that only gets run in the cleancache path.
The patch converts the virt_to_page() to struct page casting like was
done for other instances in c5f5c4db39.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Tested-By: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build when CONFIG_ISA_DMA_API is enabled but
CONFIG_COMEDI_PCI[_DRIVERS] is not enabled.
Fixes these build errors:
drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd':
drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c: At top level:
drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seen on v3.1-rc3, patch:
omap: mcbsp: Drop in-driver transfer support
bafe2721a0
Removed code that now cause tidspbridge to break while compiling.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I looks like something used to implicitly include linux/interrupt.h,
and no longer does. Fix the resulting build error by explicitly
including it.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"ret" needs to be signed for the error handling to work properly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
zcache_put_page() was modified to pass page_address(page) instead of the
actual page structure. In combination with the function signature changes
to tmem_put() and zcache_pampd_create(), zcache_pampd_create() tries to
(re)derive the page structure from the virtual address. However, if the
original page is a high memory page (or any unmapped page), this
virt_to_page() fails because the page_address() in zcache_put_page()
returned NULL.
This patch changes zcache_put_page() and zcache_get_page() to pass
the page structure instead of the page's virtual address, which
may or may not exist.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to missing memset function declaration.
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the arrival of kernel version 3.0 in the staging tree it
turns out compile error occurs for sparc64, powerpc, and arm
platforms. This patch fixes that issue.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Henry Ptasinski <henryp@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kirill Shutemov found problems with the non-upstream IMG driver where the
use of extra DRM encoder/connector types caused random crashes when the DRM
layer tried to display their matching name. This removes the MIPI types
matching the changes Pauli Nieminen made to the non upstream driver set.
As Pauli points out:
" MIPI (or DSI) is protocol specification on top of LVDS serial bus. That
makes it resonable to call MIPI connectors and encoders LVDS."
(and indeed they may also be HDMI convertors or similar when we want to
report a more useful to end user result)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xv_get_total_size_bytes returns a u64 value and it's used in a division.
This causes build failures in 32-bit architectures, as reported by Randy
Dunlap.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using different completion variables to synchronize different kernel threads
This patch fix a bug that may cause memory leak when driver
disconnected. This is not a very urgent bug. Because with the default
setting, driver disconnectting routine won't be called except when Linux
is shut down. But if the option auto_delink_en is set, a small number of
memory would leak out after memory card unplugged.
Signed-off-by: wwang <wei_wang@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The oncoming cleanup of module.h usage requires the explicit inclusion
of module.h when it was otherwise being included indirectly. Otherwise,
building zcache will fail.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this code, blkvsc_req is allocated in the cache blkdev->request_pool,
but freed in the first case to the cache blkvsc_req->dev->request_pool.
blkvsc_req->dev is subsequently initialized to blkdev, making these the
same at the second call to kmem_cache_free. But at the point of the first
call, blkvsc_req->dev is NULL. The second call is changed too, for
uniformity.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,e,e1,e2,e3;
@@
x = \(kmem_cache_alloc\|kmem_cache_zalloc\)(e1,e2)
... when != x = e
(
kmem_cache_free(e1,x);
|
?-kmem_cache_free(e3,x);
+kmem_cache_free(e1,x);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a note about the abuse of the clk API to the nvec/TODO list.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert array index from the loop bound to the loop index.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,ar;
@@
for(e1 = 0; e1 < e2; e1++) { <...
ar[
- e2
+ e1
]
...> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x86_64 allmodconfig:
In file included from arch/x86/include/asm/uaccess.h:572,
from include/linux/uaccess.h:5,
from drivers/staging/speakup/devsynth.c:4:
In function 'copy_from_user',
inlined from 'speakup_file_write' at drivers/staging/speakup/devsynth.c:28:
arch/x86/include/asm/uaccess_64.h:64: error: call to 'copy_from_user_overflow' declared with attribute error: copy_from_user() buffer size is not provably correct
I'm not sure what was unprovable about it, but size_t is the correct type
anyway.
Also replace needless min_t() with min()
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This code was cut and pasted in several places. It's missing some
unlocks on error.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Seen during an allmodconfig build for sparc:
CC [M] drivers/staging/ft1000/ft1000-pcmcia/ft1000_proc.o
In file included from drivers/staging/ft1000/ft1000-pcmcia/ft1000_proc.c:26:
drivers/staging/ft1000/ft1000-pcmcia/ft1000.h: In function 'ft1000_read_reg':
drivers/staging/ft1000/ft1000-pcmcia/ft1000.h:80: error: implicit declaration of function 'inw'
drivers/staging/ft1000/ft1000-pcmcia/ft1000.h: In function 'ft1000_write_reg':
drivers/staging/ft1000/ft1000-pcmcia/ft1000.h:86: error: implicit declaration of function 'outw'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The private object support has migrated from gma500 into the DRM core,
remove our now clashing copy so -next can build.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This avoids tainting the kernel as if a proprietary module was loaded.
The kernel will still be tainted because this is a staging driver.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
zcache is only building tmem.c and not building zcache.c. To keep the
module name, zcache.c must be renamed if symbols from tmem.c are to
remain unexported.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9
gro: Only reset frag0 when skb can be pulled
...
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several coding style errors as reported by checkpatch.pl. This
patch should fix those errors with the single exception of the open square
bracket issue on line 45.
[mchehab@redhat.com: Fix a merge conflict]
Signed-off-by: Adam M. Dutko <dutko.adam@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix compilation of ngene/ddbridge for DVB_CXD2099=n.
Note: Bug was introduced by commit 'cxd2099: Update to latest version'.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CHK_ERROR macro does a flow control, violating chapter 12
of the Documentation/CodingStyle. Doing flow controls inside
macros is a bad idea, as it hides what's happening. It also
hides the var "status" with is also a bad idea.
The changes were done by this small perl script:
my $blk=0;
while (<>) {
s/^\s+// if ($blk);
$f =~ s/\s+$// if ($blk && /^\(/);
$blk = 1 if (!m/\#/ && m/CHK_ERROR/);
$blk=0 if ($blk && m/\;/);
s/\n/ / if ($blk);
$f.=$_;
};
$f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;([^\n]*),\n\1status = \2;\3\n\1if (status < 0)\n\1\tbreak;,g;
print $f;
And manually fixed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A merge with Linus' tree added a double include of linux/interrupt.h.
Fix by removing one of the includes.
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
so replace it with mdelay(20).
Fixes build error:
ERROR: "__bad_udelay" [drivers/staging/gma500/psb_gfx.ko] undefined!
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (741 commits)
staging:iio:meter:ade7753 should be 16 bit read not 8 bit for mode register.
staging:iio:kfifo_buf fix double initialization of the ring device structure.
staging:iio:accel:lis3l02dq: fix incorrect pointer passed to spi_set_drvdata.
staging:iio:imu fix missing register table index for some channels
spectra: enable device before poking it
staging: rts_pstor: Fix a miswriting
staging/lirc_bt829: Return -ENODEV when no hardware is found.
staging/lirc_parallel: remove pointless prototypes.
staging/lirc_parallel: fix panic on rmmod
staging:iio:adc:ad7476: Incorrect pointer into spi_set_drvdata.
Staging: zram: Fix kunmapping order
Revert "gma500: Fix dependencies"
gma500: Add medfield header
gma500: wire up the mrst i2c bus from chip_info
gma500: Fix DPU build
gma500: Clean up the DPU config and make it runtime
gma500: resync with Medfield progress
gma500: Use the mrst helpers and power control for mode commit
gma500@ Fix backlight range error
gma500: More Moorestown muddle meddling means MM maybe might modeset
...
Fix up fairly trivial conflicts all over, mostly due to header file
cleanup conflicts, but some deleted files and some just context changes:
- Documentation/feature-removal-schedule.txt
- drivers/staging/bcm/headers.h
- drivers/staging/brcm80211/brcmfmac/dhd_linux.c
- drivers/staging/brcm80211/brcmfmac/dhd_sdio.c
- drivers/staging/brcm80211/brcmfmac/wl_cfg80211.h
- drivers/staging/brcm80211/brcmfmac/wl_iw.c
- drivers/staging/et131x/et131x_netdev.c
- drivers/staging/rtl8187se/ieee80211/ieee80211_softmac.c
- drivers/staging/rtl8192e/r8192E.h
- drivers/staging/usbip/userspace/src/utils.h
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: take the ACL checks to common code
bury posix_acl_..._masq() variants
kill boilerplates around posix_acl_create_masq()
generic_acl: no need to clone acl just to push it to set_cached_acl()
kill boilerplate around posix_acl_chmod_masq()
reiserfs: cache negative ACLs for v1 stat format
xfs: cache negative ACLs if there is no attribute fork
9p: do no return 0 from ->check_acl without actually checking
vfs: move ACL cache lookup into generic code
CIFS: Fix oops while mounting with prefixpath
xfs: Fix wrong return value of xfs_file_aio_write
fix devtmpfs race
caam: don't pass bogus S_IFCHR to debugfs_create_...()
get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
asus-wmi: ->is_visible() can't return negative
fix jffs2 ACLs on big-endian with 16bit mode_t
9p: close ACL leaks
ocfs2_init_acl(): fix a leak
VFS : mount lock scalability for internal mounts
So use mdelay(20) instead. Fixes this build error:
ERROR: "__bad_udelay" [drivers/staging/gma500/psb_gfx.ko] undefined!
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
