This adds support for exporting the mac80211 TXQ stats via nl80211 by
way of a nested TXQ stats attribute, as well as for configuring the
quantum and limits that were previously only changeable through debugfs.
This commit adds just the nl80211 API, a subsequent commit adds support to
mac80211 itself.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Average ack rssi will be given to userspace via NL80211 interface
if firmware is capable. Userspace tool ‘iw’ can process this
information and give the output as one of the fields in
‘iw dev wlanX station dump’.
Example output :
localhost ~ #iw dev wlan-5000mhz station dump Station
34:f3:9a:aa:3b:29 (on wlan-5000mhz)
inactive time: 5370 ms
rx bytes: 85321
rx packets: 576
tx bytes: 14225
tx packets: 71
tx retries: 0
tx failed: 2
beacon loss: 0
rx drop misc: 0
signal: -54 dBm
signal avg: -53 dBm
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
avg ack signal: -56 dBm
authorized: yes
authenticated: yes
associated: yes
preamble: short
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 203 seconds
Main use case is to measure the signal strength of a connected station
to AP. Data packet transmit rates and bandwidth used by station can vary
a lot even if the station is at fixed location, especially if the rates
used are multi stream(2stream, 3stream) rates with different bandwidth(20/40/80 Mhz).
These multi stream rates are sensitive and station can use different transmit power
for each of the rate and bandwidth combinations. RSSI measured from these RX packets
on AP will be not stable and can vary a lot with in a short time.
Whereas 802.11 ack frames from station are sent relatively at a constant
rate (6/12/24 Mbps) with constant bandwidth(20 Mhz).
So average rssi of the ack packets is good and more accurate.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME.
Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME.
Userspace should also provide the destination address and the protocol
type to use when sending the frame. This is used to implement TX of
Pre-authentication frames. If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is
specified, then the driver will be asked not to encrypt the outgoing
frame.
A new EXT_FEATURE flag is introduced so that nl80211 code can check
whether a given wiphy has capability to pass EAPoL frames over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit also adds cfg80211_rx_control_port function. This is used
to generate a CMD_CONTROL_PORT_FRAME event out to userspace. The
conn_owner_nlportid is used as the unicast destination. This means that
userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port
over nl80211 routing is requested in NL80211_CMD_CONNECT,
NL80211_CMD_ASSOCIATE, NL80211_CMD_START_AP or IBSS/mesh join.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[johannes: fix return value of cfg80211_rx_control_port()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In general regulatory self managed devices maintain their own
regulatory profiles thus it doesn't have to query the regulatory database
on country change.
ETSI has recently introduced a new channel access mechanism for 5GHz
that all wlan devices need to comply with.
These values are stored in the regulatory database.
There are self managed devices which can't maintain these
values on their own. Add API to allow self managed regulatory devices
to query the regulatory database for high band wmm rule.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[johannes: fix documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently bw and smps_mode are u8 type value in sta_opmode_info
structure. This values filled in mac80211 from ieee80211_sta_rx_bandwidth
and ieee80211_smps_mode. These enum values are specific to mac80211 and
userspace/cfg80211 doesn't know about that. This will lead to incorrect
result/assumption by the user space application.
Change bw and smps_mode parameters to their respective enums in nl80211.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only works if the IV was stripped from packets. Create a smaller
variant of ieee80211_rx_h_amsdu, which bypasses checks already done
within the fast-rx context.
In order to do so, update cfg80211's ieee80211_data_to_8023_exthdr()
to take the offset between header and snap.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch provides support to get ack signal in probe client response
and in station info from user.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
[squash in compilation fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ht/vht action frames will be sent to AP from station to notify
change of its ht/vht opmode(max bandwidth, smps mode or nss) modified
values. Currently these valuse used by driver/firmware for rate control
algorithm. This patch introduces NL80211_CMD_STA_OPMODE_CHANGED
command to notify those modified/current supported values(max bandwidth,
smps mode, max nss) to userspace application. This will be useful for the
application like steering, which closely monitoring station's capability
changes. Since the application has taken these values during station
association.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This interface allows the host driver to offload the authentication to
user space. This is exclusively defined for host drivers that do not
define separate commands for authentication and association, but rely on
userspace SME (e.g., in wpa_supplicant for the ~WPA_DRIVER_FLAGS_SME
case) for the authentication to happen. This can be used to implement
SAE without full implementation in the kernel/firmware while still being
able to use NL80211_CMD_CONNECT with driver-based BSS selection.
Host driver sends NL80211_CMD_EXTERNAL_AUTH event to start/abort
authentication to the port on which connect is triggered and status
of authentication is further indicated by user space to host
driver through the same command response interface.
User space entities advertise this capability through the
NL80211_ATTR_EXTERNAL_AUTH_SUPP flag in the NL80211_CMD_CONNECT request.
Host drivers shall look at this capability to offload the authentication.
Signed-off-by: Srinivas Dasari <dasaris@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[add socket connection ownership check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When creating a new radio on the fly, hwsim allows this
to be done with an arbitrary number of channels, but
cfg80211 only supports a limited number of simultaneous
channels, leading to a warning.
Fix this by validating the number - this requires moving
the define for the maximum out to a visible header file.
Reported-by: syzbot+8dd9051ff19940290931@syzkaller.appspotmail.com
Fixes: b59ec8dd43 ("mac80211_hwsim: fix number of channels in interface combinations")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
-----BEGIN PGP SIGNATURE-----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=M0gz
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-01-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have things all over the place, no point listing them.
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit enhances the scan results to report the per chain signal
strength based on the latest BSS update. This provides similar
information to what is already available through STA information.
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ca986ad9bc (nl80211: allow multiple active scheduled scan
requests) removed WIPHY_FLAG_SUPPORTS_SCHED_SCAN but left the kerneldoc
description in place, leading to this docs-build warning:
./include/net/cfg80211.h:3278: warning: Excess enum value
'WIPHY_FLAG_SUPPORTS_SCHED_SCAN' description in 'wiphy_flags'
Remove the line and gain a bit of peace.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both cfg80211_rx_mgmt and cfg80211_report_obss_beacon functions send
reports to userspace using NL80211_ATTR_RX_SIGNAL_DBM attribute w/o
any processing of their input signal values. Which means that in
order to match userspace tools expectations, input signal values
for those functions are supposed to be in dBm units.
This patch cleans up comments, variable names, and trace reports
for those functions, replacing confusing 'mBm' by 'dBm'.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers that implement static WEP internally for IBSS.
Add the WEP keys to the IBSS params struct, that will allow the driver
to use the keys in the join flow, and not only after the connection.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an event that indicates that a connection is authorized
(i.e. the 4 way handshake was performed by the driver). This event
should be sent by the driver after sending a connect/roamed event.
This is useful for networks that require 802.1X authentication.
In cases that the driver supports 4 way handshake offload, but the
802.1X authentication is managed by user space, the driver needs to
inform user space right after the 802.11 association was completed
so user space can initialize its 802.1X state machine etc.
However, it is also possible that the AP will choose to skip the
802.1X authentication (e.g. when PMKSA caching is used) and proceed
with the 4 way handshake immediately. In this case the driver needs
to inform user space that 802.1X authentication is no longer required
(e.g. to prevent user space from disconnecting since it did not get
any EAPOLs from the AP).
This is also useful for roaming, in which case it is possible that
the driver used the Fast Transition protocol so 802.1X is not
required.
Since there will now be a dedicated notification indicating that the
connection is authorized, the authorized flag can be removed from the
roamed event. Drivers can send the new port authorized event right
after sending the roamed event to indicate the new AP is already
authorized. This therefore reserves the old PORT_AUTHORIZED attribute.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function hasn't been used since the removal of iwmc3200wifi
in 2012. It also appears to have a bug when qos=True, since then
it'll copy uninitialized stack memory to the SKB.
Just remove the function entirely.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current ieee80211_ie_split() implementation doesn't
account for elements that are sub-elements of the
EXTENSION IE. To extend support to these IEs as well,
treat the WLAN_EID_EXTENSION ids in the %ids array
as indicating that the next id in the array is a
sub-element of the EXTENSION IE.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that initiate roaming while being connected to a network that
uses 802.1X authentication need to inform user space if 802.1X
authentication is further required after roaming.
For example, when using the Fast transition protocol, roaming within
the mobility domain does not require new 802.1X authentication, but
roaming to another mobility domain does.
In addition, some drivers may not support 802.1X authentication
(so it has to be done in user space), while other drivers do.
Add a flag to the roaming notification to indicate if user space is
required to do 802.1X authentication after the roaming or not.
This flag will only be used for networks that use 802.1X
authentication. For networks that do not use 802.1X authentication it
is assumed that no further action is required from user space after
the roaming notification.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[arend.vanspriel@broadcom.com reuse NL80211_ATTR_PORT_AUTHORIZED]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[rebase to apply w/o the flag in CONNECT]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add API for setting the PMK to the driver. For FT support, allow
setting also the PMK-R0 Name.
This can be used by drivers that support 4-Way handshake offload
while IEEE802.1X authentication is managed by upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[arend.vanspriel@broadcom.com: add WANT_1X_4WAY_HS attribute]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X docs a bit to
say that the device may require it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let drivers advertise support for station-mode 4-way handshake
offloading with a new NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK flag.
Extend use of NL80211_ATTR_PMK attribute indicating it might be passed
as part of NL80211_CMD_CONNECT command, and contain the PSK (which is
the PMK, hence the name.)
The driver/device is assumed to handle the 4-way handshake by
itself in this case (including key derivations, etc.), instead
of relying on the supplicant.
This patch is somewhat based on this one (by Vladimir Kondratiev):
https://patchwork.kernel.org/patch/1309561/.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[arend.vanspriel@broadcom.com rebase dealing with existing ATTR_PMK]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK docs to indicate
that this offload might be required]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When joining a mesh network it is not guaranteed that userspace has a
daemon listening for radar events. This is however required for channels
requiring DFS. To flag that userspace will handle radar events, it needs
to set NL80211_ATTR_HANDLE_DFS.
This matches the current mechanism used for IBSS mode.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace @results_wk with @report_results, which was missed
in an earlier patch between revisions thereof.
Fixes: b34939b983 ("cfg80211: add request id to cfg80211_sched_scan_*() api")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the way I did the RX bitrate conversions in mac80211 with
spatch, going setting flags to setting the value, many drivers now
don't set the bandwidth value for 20 MHz, since with the flags it
wasn't necessary to (there was no 20 MHz flag, only the others.)
Rather than go through and try to fix up all the drivers, instead
renumber the enum so that 20 MHz, which is the typical bandwidth,
actually has the value 0, making those drivers all work again.
If VHT was hit used with a driver not reporting it, e.g. iwlmvm,
this manifested in hitting the bandwidth warning in
cfg80211_calculate_bitrate_vht().
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_roamed() and cfg80211_roamed_bss() take the same arguments
except that cfg80211_roamed() requires the BSSID and
cfg80211_roamed_bss() requires the bss entry.
Unify the two functions by using a struct for driver initiated
roaming information so that either the BSSID or the bss entry can be
passed as an argument to the unified function.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[modified the ath6k, brcm80211, rndis and wlan-ng drivers accordingly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[modify brcmfmac to remove the useless cast, spotted by Arend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch allows for the scheduled scan request to specify matchsets
for specific BSSIDs.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[docs, netlink policy fix]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to allocate a portid structure and then, for
each of those, walk the interfaces - we can just add a flag
to each interface and walk those directly. Due to padding in
the struct, we can even do it without any memory cost, and
it even simplifies the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-scheduled scan support in subsequent patch a request id
will be added. This patch add this request id to the scheduled
scan event messages. For now the request id will always be zero.
With multi-scheduled scan its value will inform user-space to which
scan the event relates.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing monitor parameters, not setting the MU-MIMO attributes
should mean that they're not changed - it's documented that to turn
the feature off it's necessary to set all-zero group membership and
an invalid follow-address. This isn't implemented.
Fix this by making the parameters pointers, stop reusing the macaddr
struct member, and documenting that NULL pointers mean unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enhance nl80211 and cfg80211 connect request and response APIs to
support FILS shared key authentication offload. The new nl80211
attributes can be used to provide additional information to the driver
to establish a FILS connection. Also enhance the set/del PMKSA to allow
support for adding and deleting PMKSA based on FILS cache identifier.
Add a new feature flag that drivers can use to advertize support for
FILS shared key authentication and association in station mode when
using their own SME.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the connect event from driver takes all the connection
response parameters as arguments. With support for new features these
response parameters can grow. Use a structure to pass these parameters
rather than passing them as function arguments.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[add to documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the SET CQM command's RSSI threshold attribute to accept any
number of thresholds as a sorted array. The API should be backwards
compatible so that if one s32 threshold value is passed, the old
mechanism is enabled. The netlink event generated is the same in both
cases.
cfg80211 handles an arbitrary number of RSSI thresholds but drivers have
to provide a method (set_cqm_rssi_range_config) that configures a range
set by a high and a low value. Drivers have to call back when the RSSI
goes out of that range and there's no additional event for each time the
range is reconfigured as there was with the current one-threshold API.
This method doesn't have a hysteresis parameter because there's no
benefit to the cfg80211 code from having the hysteresis be handled by
hardware/driver in terms of the number of wakeups. At the same time
it would likely be less consistent between drivers if offloaded or
done in the drivers.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
disassocation||disassociation
Link: http://lkml.kernel.org/r/1481573103-11329-27-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The nl80211_nan_dual_band_conf enumeration doesn't make much sense.
The default value is assigned to a bit, which makes it weird if the
default bit and other bits are set at the same time.
To improve this, get rid of NL80211_NAN_BAND_DEFAULT and add a wiphy
configuration to let the drivers define which bands are supported.
This is exposed to the userspace, which then can make a decision on
which band(s) to use. Additionally, rename all "dual_band" elements
to "bands", to make things clearer.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the benefit of drivers that rebuild IEs in firmware, parse the
IEs for HT/VHT capabilities and the respective membership selector
in the (extended) supported rates. This avoids duplicating the same
code into all drivers that need this information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new restructured text parser complains about the formatting,
and really this should be a definition list.
In order to fix this without introducing trailing whitespace,
convert to the inline kernel-doc format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function documentation for cfg80211_connect_bss() and
cfg80211_connect_result() was still claiming that they are used only for
a success case while these functions can now be used to report both
success and various failure cases. The actual use cases were already
described in the connect() documentation.
Update the function specific comments to note the failure cases and also
describe how the special status == -1 case is used in
cfg80211_connect_bss() to indicate a connection timeout based on the
internal implementation in cfg80211_connect_timeout().
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[use tabs for indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enhances the connect timeout API to also carry the reason for the
timeout. These reason codes for the connect time out are represented by
enum nl80211_timeout_reason and are passed to user space through a new
attribute NL80211_ATTR_TIMEOUT_REASON (u32).
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[keep gfp_t argument last]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enhance sched scan to support option of finding a better BSS while in
connected state. Firmware scans the medium and reports when it finds a
known BSS which has better RSSI than the current connected BSS. New
attributes to specify the relative RSSI (compared to the current BSS)
are added to the sched scan to implement this.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disconnect or deauthenticate when the owning socket is closed if this
flag is supplied to CMD_CONNECT or CMD_ASSOCIATE. This may be used
to ensure userspace daemon doesn't leave an unmanaged connection behind.
In some situations it would be possible to account for that, to some
degree, in the deamon restart code or in the up/down scripts without
the use of this attribute. But there will be systems where the daemon
can go away for varying periods without a warning due to local resource
management.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a helper for reading that new property and applying
limitations of supported channels specified this way.
It is used with devices that normally support a wide wireless band but
in a given config are limited to some part of it (usually due to board
design). For example a dual-band chipset may be able to support one band
only because of used antennas.
It's also common that tri-band routers have separated radios for lower
and higher part of 5 GHz band and it may be impossible to say which is
which without a DT info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[add new function to documentation, fix link]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
Add functionality to update the connection parameters when in connected
state, so that driver/firmware uses the updated parameters for
subsequent roaming. This is for drivers that support internal BSS
selection and roaming. The new command does not change the current
association state, i.e., it can be used to update IE contents for future
(re)associations without causing an immediate disassociation or
reassociation with the current BSS.
This commit implements the required functionality for updating IEs for
(Re)Association Request frame only. Other parameters can be added in
future when required.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability to configure if an AP (and associated VLANs) will
do multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own MAC
address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[fix disabling, add better documentation & commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new nl80211 attributes can be used to provide KEK and nonces to
allow the driver to encrypt and decrypt FILS (Re)Association
Request/Response frames in station mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define the Element IDs and Element ID Extensions from IEEE
P802.11ai/D11.0. In addition, add a new cfg80211_find_ext_ie() wrapper
to make it easier to find information elements that used the Element ID
Extension field.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds defines and nl80211 extensions to allow FILS Authentication to
be implemented similarly to SAE. FILS does not need the special rules
for the Authentication transaction number and Status code fields, but it
does need to add non-IE fields. The previously used
NL80211_ATTR_SAE_DATA can be reused for this to avoid having to
duplicate that implementation. Rename that attribute to more generic
NL80211_ATTR_AUTH_DATA (with backwards compatibility define for
NL80211_SAE_DATA).
Also document the special rules related to the Authentication
transaction number and Status code fiels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the pointless checking against interface combinations in
the initial basic beacon interval validation, that currently isn't
taking into account radar detection or channels properly. Instead,
just validate the basic range there, and then delay real checking
to the interface combination validation that drivers must do.
This means that drivers wanting to use the beacon_int_min_gcd will
now have to pass the new_beacon_int when validating the AP/mesh
start.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a helper using wdev to check if interface is running. This
deals with both non-netdev and netdev interfaces. In struct
wireless_dev replace 'p2p_started' and 'nan_started' by
'is_running' as those are mutually exclusive anyway, and unify
all the code to use wdev_running().
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On a disconnect request from userspace, cfg80211 currently calls
called rdev_disconnect() only in case that 'current_bss' was set,
i.e. connection had been established.
Change this to allow the userspace call to succeed and call the
driver's disconnect() method also while the connection attempt is
in progress, to be able to abort attempts.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[change commit subject/message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The uapsd_queue field is in QoS IE order and not in
IEEE80211_AC_*'s order.
This means that mac80211 would get confused between
BK and BE which is certainly not such a big deal but
needs to be fixed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Only 32 more to go...
-----BEGIN PGP SIGNATURE-----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=U9Pc
-----END PGP SIGNATURE-----
Merge tag 'docs-4.9-2' of git://git.lwn.net/linux
Pull one more documentation update from Jonathan Corbet:
"A single commit converting the mac80211 DocBook template over to
Sphinx. Only 32 more to go..."
* tag 'docs-4.9-2' of git://git.lwn.net/linux:
docs-rst: sphinxify 802.11 documentation
This commit provides a mechanism for the host drivers to advertise the
support for different beacon intervals among the respective interface
combinations in a group, through NL80211_IFACE_COMB_BI_MIN_GCD (u32).
This value will be compared against GCD of all beaconing interfaces of
matching combinations.
If the driver doesn't advertise this value, the old behaviour where
all beacon intervals must be identical is retained.
If it is specified, then any beacon interval for an interface in the
interface combination as well as the GCD of all active beacon intervals
in the combination must be greater or equal to this value.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
[change commit message, some variable names, small other things]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the growing parameter list to a structure for the interface
combination check and iteration functions in cfg80211 and mac80211
to make the code easier to understand.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not accept arbitrary DA/SA inside A-MSDUs, it could be used
to circumvent protections, like allowing a station to send frames and
make them seem to come from somewhere else.
Add the necessary infrastructure in cfg80211 to allow such checks, in
further patches we'll start using them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single case where has_80211_header is passed as true,
which is in mac80211. Given that there's only simple code that needs
to be done before calling it, export that function from cfg80211
instead and let mac80211 call it itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is just a very basic conversion, I've split up the original
multi-book template, and also split up the multi-part mac80211
part in the original book; neither of those were handled by the
automatic pandoc conversion.
Fix errors that showed up, resulting in a much nicer rendering,
at least for the interface combinations documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Provide a function that reports NAN DE function termination. The function
may be terminated due to one of the following reasons: user request,
ttl expiration or failure.
If the NAN instance is tied to the owner, the notification will be
sent to the socket that started the NAN interface only
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide a function the driver can call to report a match.
This will send the event to the user space.
If the NAN instance is tied to the owner, the notifications will be
sent to the socket that started the NAN interface only.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some NAN configuration paramaters may change during the operation of
the NAN device. For example, a user may want to update master preference
value when the device gets plugged/unplugged to the power.
Add API that allows to do so.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A NAN function can be either publish, subscribe or follow
up. Make all the necessary verifications and just pass the
request to the driver.
Allow the user space application that starts NAN to
forbid any other socket to add or remove functions.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows user space to start/stop NAN interface.
A NAN interface is like P2P device in a few aspects: it
doesn't have a netdev associated to it.
Add the new interface type and prevent operations that
can't be executed on NAN interface like scan.
Define several attributes that may be configured by user space
when starting NAN functionality (master preference and dual
band operation)
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for drivers that implement static WEP internally, i.e.
expose connection keys to the driver in connect flow and don't
upload the keys after the connection.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous commit added support for specifying the beacon rate
for AP mode. Add features checks to this, and extend it to also
support the rate configuration for mesh networks. For IBSS it's
not as simple due to joining etc., so that's not yet supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows an option to configure a single beacon tx rate for an AP.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
-----BEGIN PGP SIGNATURE-----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=s1MY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have various things - all across the board:
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few places where an IE that matches not only the EID, but
also other bytes inside the element, needs to be found. To simplify
that and reduce the amount of similar code, implement a new helper
function to match the EID and an extra array of bytes.
Additionally, simplify cfg80211_find_vendor_ie() by using the new
match function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211 expects the .disconnect() handler to call
cfg80211_disconnect() when done. Make this requirement
more explicit.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows modules using this function (currently: batman-adv) to
compile even if cfg80211 is not built at all, thus relaxing
dependencies.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add API to support VHT MU-MIMO air sniffer.
in MU-MIMO there are parallel frames on the air while the HW
has only one RX.
add the capability to sniff one of the MU-MIMO parallel frames by
giving the sniffer additional information so it'll know which
of the parallel frames it shall follow.
Add attribute - NL80211_ATTR_MU_MIMO_GROUP_DATA - for getting
a MU-MIMO groupID in order to monitor packets from that group
using VHT MU-MIMO.
And add attribute -NL80211_ATTR_MU_MIMO_FOLLOW_ADDR - for passing
MAC address to monitor mode.
that option will be used by VHT MU-MIMO air sniffer to follow a
station according to it's MAC address using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver extended capabilities may differ for different
interface types which the userspace needs to know (for
example the fine timing measurement initiator and responder
bits might differ for a station and AP). Add a new nl80211
attribute to provide extended capabilities per interface type
to userspace.
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, the status parameter to cfg80211_connect_result() was
documented as using WLAN_STATUS_UNSPECIFIED_FAILURE (1) when the real
status code for the failure is not known. This value can be used by an
AP (and often is) and as such, user space cannot distinguish between
explicitly rejected authentication/association and not being able to
even try to associate or not receiving a response from the AP.
Add a new inline function, cfg80211_connect_timeout(), to be used when
the driver knows that the connection attempt failed due to a reason
where connection could not be attempt or no response was received from
the AP. The internal functions now allow a negative status value (-1) to
be used as an indication of this special case. This results in the
NL80211_ATTR_TIMED_OUT to be added to the NL80211_CMD_CONNECT event to
allow user space to determine this case was hit. For backwards
compatibility, NL80211_STATUS_CODE with the value
WLAN_STATUS_UNSPECIFIED_FAILURE is still indicated in the event in such
a case.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[johannes: fix cfg80211_connect_bss() prototype to use int for status,
add cfg80211_connect_timeout() to docbook, fix docbook]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows finding vendor IE from a specific vendor.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 maintains separate BSS table entries for APs if the same
BSSID, SSID pair is seen on multiple channels, it is possible that it
can map the current_bss to a BSS entry on the wrong channel. This
current_bss will not get flushed unless disconnected and cfg80211
reports a wrong channel as the associated channel.
Fix this by introducing a new cfg80211_connect_bss() function which is
similar to cfg80211_connect_result(), but it includes an additional
parameter: the bss the STA is connected to. This allows drivers to
provide the exact bss entry that matches the BSS to which the connection
was completed.
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the a station statistics netlink attribute:
NL80211_STA_INFO_RX_DURATION.
If present, this attribute contains the aggregate PPDU duration (in
microseconds) for all the frames from the peer. This is useful to
help understand the total time spent transmitting to us by all of
the connected peers.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The roaming cases for the Connect command were not fully covered and
neither Connect nor Associate command uses of the prev_bssid parameter
were very clear. Add details to describe how the prev_bssid argument is
supposed to be used and when the driver should use association or
reassociation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends NL80211_CMD_CONNECT to allow the NL80211_ATTR_PREV_BSSID
attribute to be used similarly to way this was already allowed with
NL80211_CMD_ASSOCIATE. This allows user space to request reassociation
(instead of association) when already connected to an AP. This provides
an option to reassociate within an ESS without having to disconnect and
associate with the AP.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanisms, and thus
if a P2P GO has a legacy client connected to it, it has to make
some changes in the PS behavior.
To handle this, add an attribute to specify whether a station supports
P2P PS or not. If the attribute was not specified cfg80211 will assume
that station supports it for P2P GO interface, and does NOT support it
for AP interface, matching the current assumptions in the code.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fix a structure name mismatch in cfg80211.h.
Signed-off-by: Moroo Akira <retrage01@gmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introducing a new feature that the driver can use to
indicate the driver/firmware supports configuration of BSS
selection criteria upon CONNECT command. This can be useful
when multiple BSS-es are found belonging to the same ESS,
ie. Infra-BSS with same SSID. The criteria can then be used to
offload selection of a preferred BSS.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Lei Zhang <leizh@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[move wiphy support check into parse_bss_select()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows scans for a specific BSSID to be optimized by the user space
application by requesting the driver to set the Probe Request frame
BSSID field (Address 3) to the specified BSSID instead of the wildcard
BSSID. This prevents other APs from replying which reduces airtime need
and latency in getting the response from the target AP through.
This is an optimization and as such, it is acceptable for some of the
drivers not to support the mechanism. If not supported, the wildcard
BSSID will be used and more responses may be received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PBSS (Personal Basic Service Set) is a new BSS type for DMG
networks. It is similar to infrastructure BSS, having an AP-like
entity called PCP (PBSS Control Point), but it has few differences.
PBSS support is mandatory for 11ad devices.
Add support for PBSS by introducing a new PBSS flag attribute.
The PBSS flag is used in the START_AP command to request starting
a PCP instead of an AP, and in the CONNECT command to request
connecting to a PCP instead of an AP.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement new functionality for aborting an ongoing scan.
Add NL80211_CMD_ABORT_SCAN to the nl80211 interface. After
aborting the scan, driver shall provide the scan status by
calling cfg80211_scan_done().
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[change command to take wdev instead of netdev so that it
can be used on p2p-device scans]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is a very simple wrapper around another one,
just adds a few default parameters, so replace it with a
static inline instead of using EXPORT_SYMBOL, reducing
the module size slightly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The previous patch changed mac80211 to always report an event
after a CQM RSSI reconfiguration. Document that as expected
behaviour in both the cfg80211 and mac80211 API.
Currently, iwlmvm already implements that behaviour; the other
drivers implementing CQM RSSI events may have to be changed.
This behaviour lets userspace know what the current state is
without relying on querying the data which is racy.
Reviewed-by: Sharon, Sara <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the option to configure multiple 'scan plans' for scheduled scan.
Each 'scan plan' defines the number of scan cycles and the interval
between scans. The scan plans are executed in the order they were
configured. The last scan plan will always run infinitely and thus
defines only the interval between scans.
The maximum number of scan plans supported by the device and the
maximum number of iterations in a single scan plan are advertised
to userspace so it can configure the scan plans appropriately.
When scheduled scan results are received there is no way to know which
scan plan is being currently executed, so there is no way to know when
the next scan iteration will start. This is not a problem, however.
The scan start timestamp is only used for flushing old scan results,
and there is no difference between flushing all results received until
the end of the previous iteration or the start of the current one,
since no results will be received in between.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For location and connectivity services, userspace would often like
to know the time when the BSS was last seen. The current "last seen"
value is calculated in a way that makes it less useful, especially
if the system suspended in the meantime.
Add the ability for the driver to report a real CLOCK_BOOTTIME stamp
that can then be reported to userspace (if present).
Drivers wishing to use this must be converted to the new API to call
cfg80211_inform_bss_data() or cfg80211_inform_bss_frame_data(). They
need to ensure the reported value is accurate enough even when the
frame might have been buffered in the device (e.g. firmware.)
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
[modified to use struct, inlines]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 rejects capability updates for existing entries
and as a result it's impossible to update entries that were added
unassociated, but that is necessary to go through the full station
states from userspace, adding a station before authentication etc.
Fix this by allowing updates to capabilities for stations that the
driver (or mac80211) assigned unassociated state. Drivers setting
the full station state support flag must use the new station type
for proper operation.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This callback is currently not allowed to sleep, which makes it more
difficult to implement proper driver methods in mac80211 than it has
to be. Instead of doing asynchronous work here in mac80211, make it
possible for the callback to sleep by doing some asynchronous work
in cfg80211. This also enables improvements to other drivers, like
ath6kl, that would like to sleep in this callback.
While at it, also fix the code to call the driver on the implicit
unregistration when an interface is removed, and do that also when
a P2P-Device wdev is destroyed (otherwise we leak the structs.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RTNL is required to check for IR-relaxation conditions that allow
more channels to beacon. Export an RTNL locked version of reg_can_beacon
and use it where possible in AP/STA interface type flows, where
IR-relaxation may be applicable.
Fixes: 06f207fc54 ("cfg80211: change GO_CONCURRENT to IR_CONCURRENT for STA")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.
Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.
For libertas, make adjustments as indicated by Dan Williams.
Reported-by: Matthieu Mauger <matthieux.mauger@intel.com>
Tested-by: Matthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.
Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the next patch will require the IE splitting utility functions
in cfg80211, move them there from mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This will expose in /sys whether the ifname of a device is set by
userspace or generated by the kernel. The latter kind (wlanX, etc)
is not deterministic, so userspace needs to rename these devices
to names that are guaranteed to stay the same between reboots. The
former, however should never be renamed, so userspace needs to be
able to reliably tell the difference.
Similar functionality was introduced for the rtnetlink core in
commit 5517750f05 ("net: rtnetlink - make create_link take name_assign_type")
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
[reformat changelog to fit 72 cols]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Seems Broadcom TDLS peers (Nexus 5, Xperia Z3) refuse to allow TDLS
connection when channel-switching is supported but the regulatory
classes IE is missing from the setup request.
Add a chandef to reg-class translation function to cfg80211 and use it
to add the required IE during setup. For now add only the current
regulatory class as supported - it is enough to resolve the
compatibility issue.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having to say
> #ifdef CONFIG_NET_NS
> struct net *net;
> #endif
in structures is a little bit wordy and a little bit error prone.
Instead it is possible to say:
> typedef struct {
> #ifdef CONFIG_NET_NS
> struct net *net;
> #endif
> } possible_net_t;
And then in a header say:
> possible_net_t net;
Which is cleaner and easier to use and easier to test, as the
possible_net_t is always there no matter what the compile options.
Further this allows read_pnet and write_pnet to be functions in all
cases which is better at catching typos.
This change adds possible_net_t, updates the definitions of read_pnet
and write_pnet, updates optional struct net * variables that
write_pnet uses on to have the type possible_net_t, and finally fixes
up the b0rked users of read_pnet and write_pnet.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This modifies cfg80211_vendor_event_alloc() with an additional argument
struct wireless_dev *wdev. __cfg80211_alloc_event_skb() is modified to
take in *wdev argument, if wdev != NULL, both the NL80211_ATTR_IFINDEX
and wdev identifier are added to the vendor event.
These changes make it easier for drivers to add ifindex indication in
vendor events cleanly.
This also updates all existing users of cfg80211_vendor_event_alloc()
and __cfg80211_alloc_event_skb() in the kernel tree.
Signed-off-by: Ahmad Kholaif <akholaif@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ad adds new a network type (PBSS) and changes the capability
field interpretation for the DMG (60G) band.
The same 2 bits that were interpreted as "ESS" and "IBSS" before are
re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid
values are: "IBSS", "PBSS" (new) and "AP".
In order to get the BSS struct for the new PBSS networks, change the
cfg80211_get_bss() function to take a new enum ieee80211_bss_type
argument with the valid network types, as "capa_mask" and "capa_val"
no longer work correctly (the search must be band-aware now.)
The remaining bits in "capa_mask" and "capa_val" are used only for
privacy matching so replace those two with a privacy enum as well.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
[rewrite commit log, tiny fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The userspace may want to delay the the first scheduled scan or
net-detect cycle. Add an optional attribute to the scheduled scan
configuration to pass the delay to be (optionally) used by the driver.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[add the attribute to the policy to validate it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For some reason, we made the bandwidth separate flags, which
is rather confusing - a single rate cannot have different
bandwidths at the same time.
Change this to no longer be flags but use a separate field
for the bandwidth ('bw') instead.
While at it, add support for 5 and 10 MHz rates - these are
reported as regular legacy rates with their real bitrate,
but tagged as 5/10 now to make it easier to distinguish them.
In the nl80211 API, the flags are preserved, but the code
now can also clearly only set a single one of the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are treated the same as 160 MHz in the spec, so
it makes no sense to distinguish them. As no driver uses them
yet, this is also not a problem, just remove them.
In the userspace API the field remains reserved to preserve
API and ABI.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A self-managed device will sometimes need to set its regdomain synchronously.
Notably it should be set before usermode has a chance to query it. Expose
a new API to accomplish this which requires the RTNL.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The base for the current statistics is pretty mixed up, support
exporting RX/TX statistics for MSDUs per TID. This (currently)
covers received MSDUs, transmitted MSDUs and retries/failures
thereof.
Doing it per TID for MSDUs makes more sense than say only per AC
because it's symmetric - we could export per-AC statistics for all
frames (which AC we used for transmission can be determined also
for management frames) but per TID is better and usually data
frames are really the ones we care about. Also, on RX we can't
determine the AC - but we do know the TID for any QoS MPDU we
received.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current statistics we keep aren't very clear, some are on
MPDUs and some on MSDUs/MMPDUs. Clarify the descriptions based
on the counters mac80211 keeps.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add these two values:
* BEACON_RX: number of beacons received from this peer
* BEACON_SIGNAL_AVG: signal strength average for beacons only
These can then be used for Android Lollipop's statistics request.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
* remove STATION_INFO_ASSOC_REQ_IES complete, but the length
(assoc_req_ies_len) can be used instead
* add NL80211_STA_INFO_RX_DROP_MISC which exists internally
but not in nl80211 yet
This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station is removed, its statistics may be interesting to
userspace, for example for further aggregation of statistics of
all stations that ever connected to an AP.
Introduce a new cfg80211_del_sta_sinfo() function (and make the
cfg80211_del_sta() a static inline calling it) to allow passing
a struct station_info along with this, and send the data in the
nl80211 event message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the time spent scanning to the survey data so it can be
reported by drivers that collect such information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not all devices are able to report survey data (particularly
time spent for various operations) per channel. As all these
statistics already exist in survey data, allow such devices
to report them (if userspace requested it)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All of the survey data is (currently) per channel anyway,
so having the word "channel" in the name does nothing. In
the next patch I'll introduce global data to the survey,
where the word "channel" is actually confusing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the wiphy::features flag being used up this patch adds a
new field wiphy::ext_features. Considering extensibility this
new field is declared as a byte array. This extensible flag is
exposed to user-space by NL80211_ATTR_EXT_FEATURES.
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An attribute NL80211_ATTR_SOCKET_OWNER can be set by the scan initiator.
If present, the attribute will cause the scan to be stopped if the client
dies.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because of possible races when accessing sched_scan_req pointer in
rdev, the sched_scan_req is converted to RCU pointer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new regulatory flag that allows a driver to manage regdomain
changes/updates for its own wiphy.
A self-managed wiphys only employs regulatory information obtained from
the FW and driver and does not use other cfg80211 sources like
beacon-hints, country-code IEs and hints from other devices on the same
system. Conversely, a self-managed wiphy does not share its regulatory
hints with other devices in the system. If a system contains several
devices, one or more of which are self-managed, there might be
contradictory regulatory settings between them. Usage of flag is
generally discouraged. Only use it if the FW/driver is incompatible
with non-locally originated hints.
A new API lets the driver send a complete regdomain, to be applied on
its wiphy only.
After a wiphy-specific regdomain change takes place, usermode will get
a new type of change notification. The regulatory core also takes care
enforce regulatory restrictions, in case some interfaces are on
forbidden channels.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Much of the code can be shared by moving it into helper functions
for the CQM event sending.
Also move the code closer together, even in the header file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary feature flags and a scan flag to support using
random MAC addresses for scan while unassociated.
The configuration for this supports an arbitrary MAC address
value and mask, so that any kind of configuration (e.g. fixed
OUI or full 46-bit random) can be requested. Full 46-bit random
is the default when no other configuration is passed.
Also add a small helper function to use the addr/mask correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new WoWLAN API to enable net-detect as a wake up trigger.
Net-detect allows the device to scan in the background while the
host is asleep to wake up the host system when a matching network
is found.
Reuse the scheduled scan attributes to specify how the scan is
performed while suspended and the matches that will trigger a
wake event.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce commands to initiate and cancel TDLS channel-switching. Once
TDLS channel-switching is started, the lower level driver is responsible
for continually initiating channel-switch operations and returning to
the base (AP) channel to listen for beacons from time to time.
Upon cancellation of the channel-switch all communication between the
relevant TDLS peers will continue on the base channel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new NL80211_CH_SWITCH_STARTED_NOTIFY message that can be sent to
the userspace when a channel switch process has started. This allows
userspace to take action, for instance, by requesting other interfaces
to switch channel as necessary.
This patch introduces a function that allows the drivers to send this
notification. It should be used when the driver starts processing a
channel switch initiated by a remote device (eg. when a STA receives a
CSA from the AP) and when it successfully starts a userspace-triggered
channel switch (eg. when hostapd triggers a channel swith in the AP).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when creating virtual interfaces.
Keeps udev from mucking with things it shouldn't, since
the default MAC is never seen by udev when specified on
the cmd-line during creation.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[check for feature flag in nl80211 to force drivers to set it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kernel will attempt to use the name if it is supplied,
but if name cannot be used for some reason, the default
phyX name will be used instead.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[while at it, use wiphy_name() instead of dev_name(),
fix format string issue reported by Kees Cook]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During the review of the corresponding wpa_supplicant patches we
noticed that the only way for it to detect that this functionality
is supported currently is to check for the command support. This
can be misleading though, as the command was also designed to, in
the future, support pure 802.11 TSPECs.
Expose the WMM-TSPEC feature flag to nl80211 so later we can also
expose an 802.11-TSPEC feature flag (if needed) to differentiate
the two cases.
Note: this change isn't needed in 3.18 as there's no driver there
yet that supports the functionality at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The optional NL80211_ATTR_MGMT_SUBTYPE and NL80211_ATTR_REASON_CODE
attributes can now be included in NL80211_CMD_DEL_STATION to indicate to
the driver which frame (Deauthentication/Disassociation) and reason code
in that frame should be used to indicate removal to the specific
station. This is used by drivers that implement AP SME and generate
those frames internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to add new parameters for the del_station calls
without having to modify all drivers that use this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add two new cfg80211 operations for querying a table with proxied mesh
paths.
Signed-off-by: Henning Rogge <henning.rogge@fkie.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add feature bits to indicate device support for
static-smps and dynamic-smps modes.
Add a new NL80211_ATTR_SMPS_MODE attribue to allow
configuring the smps mode to be used by the ap
(e.g. configuring to ap to dynamic smps mode will
reduce power consumption while having minor effect
on throughput)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Userspace might need to know what queues are configured
for uapsd (e.g. for setting proper default values in tspecs).
Add this bitmap to the association event (inside wmm
nested attribute)
Add additional parameter to cfg80211_rx_assoc_resp,
and update its callers.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add nl80211 and driver API to validate, add and delete traffic
streams with appropriate settings.
The API calls for userspace doing the action frame handshake
with the peer, and then allows only to set up the parameters
in the driver. To avoid setting up a session only to tear it
down again, the validate API is provided, but the real usage
later can still fail so userspace must be prepared for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to put the values on the stack, just pass a
pointer to the data in the nl80211 message. This reduces stack
usage and avoids potential issues with putting sensitive data
on the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable ACK timeout estimation algorithm (dynack) using mac80211
set_coverage_class API. Dynack is activated passing coverage class equals to -1
to lower drivers and it is automatically disabled setting valid value for
coverage class.
Define NL80211_ATTR_WIPHY_DYN_ACK flag attribute to enable dynack from
userspace. In order to activate dynack NL80211_FEATURE_ACKTO_ESTIMATION feature
flag must be set by lower drivers to indicate dynack capability.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a flag attribute to use in associations, for tagging the target
connection as supporting RRM. It is the responsibility of upper
layers to set this flag only if both the underlying device, and the
target network indeed support RRM.
To be used in ASSOCIATE and CONNECT commands.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few possible cases of where BSS data came from:
1) only a beacon has been received
2) only a probe response has been received
3) the driver didn't report what it received (this happens when
using cfg80211_inform_bss[_width]())
4) both probe response and beacon data has been received
Unfortunately, in the userspace API, a few things weren't there:
a) there was no way to differentiate cases 1) and 4) above
without comparing the data of the IEs
b) the TSF was always from the last frame, instead of being
exposed for beacon/probe response separately like IEs
Fix this by
i) exporting a new flag attribute that indicates whether or
not probe response data has been received - this addresses (a)
ii) exporting a BEACON_TSF attribute that holds the beacon's TSF
if a beacon has been received
iii) not exporting the beacon attributes in case (3) above as that
would just lead userspace into thinking the data actually came
from a beacon when that isn't clear
To implement this, track inside the IEs struct whether or not it
(definitely) came from a beacon.
Reported-by: William Seto
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver is now responsible for veryfing if the
switch is possible.
Since this is inherently tricky driver may decide
to disconnect an interface later with
cfg80211_stop_iface().
This doesn't mean driver can accept everything. It
should do it's best to verify requests and reject
them as soon as possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channels in 2.4GHz band overlap, this means that if we
send a probe request on channel 1 and then move to channel
2, we will hear the probe response on channel 2. In this
case, the RSSI will be lower than if we had heard it on
the channel on which it was sent (1 in this case).
The firmware / low level driver can parse the channel in
the DS IE or HT IE and compensate the RSSI so that it will
still have a valid value even if we heard the frame on an
adjacent channel. This can be done up to a certain offset.
Add this offset as a configuration for the low level driver.
A low level driver that can compensate the low RSSI in this
case should assign the maximal offset for which the RSSI
value is still valid.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement and export the new cfg80211_get_station() API.
This utility can be used by other kernel modules to obtain
detailed information about a given wireless station.
It will be in particular useful to batman-adv which will
implement a wireless rate based metric.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may need information about the expected throughput
towards a given peer.
This value is supposed to consider the size overhead
generated by the 802.11 header.
This value is exported in kbps through the get_station() API
by including it into the station_info object.
Moreover, it is sent to user space when replying to the
nl80211 GET_STATION command.
This information will be useful to the batman-adv module
which will use it for its new metric computation.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This requires changing the nl80211 parsing code a bit to use
intermediate pointers for the allocation, but clarifies the
API towards the drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This also propagates through the drivers.
The orinoco driver uses the cfg80211 API structs for internal
bookkeeping, and so needs a (void *) cast that removes the
const - but that's OK because it allocates those pointers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the comment in the structure to a description of the
max_num_csa_counters field in the docbook area.
This fixes a warning when building htmldocs (at least):
Warning(include/net/cfg80211.h:3064): No description found for parameter 'max_num_csa_counters'
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the type of NL80211_ATTR_CSA_C_OFF_BEACON and
NL80211_ATTR_CSA_C_OFF_PRESP to be NLA_BINARY which allows
userspace to use beacons and probe responses with
multiple CSA counters.
This isn't breaking the API since userspace can
continue to use nla_put_u16 for this attributes, which
is equivalent to a single element u16 array.
In addition advertise max number of supported CSA counters.
This is needed when using CSA and eCSA IEs together.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_ATTR_CSA_C_OFFSETS_TX which holds an array
of offsets to the CSA counters which should be updated
when sending a management frames with NL80211_CMD_FRAME.
This API should be used by the drivers that wish to keep the
CSA counter updated in probe responses, but do not implement
probe response offloading and so, do not use
ieee80211_proberesp_get function.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At the moment, the ath9k/ath10k DFS module only supports detecting ETSI
radar patterns.
Add a bitmap in the interface combinations, indicating which DFS regions
are supported by the detector. If unset, support for all regions is
assumed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver fails during HW restart or resume, the whole
stack goes into a very confused state with interfaces being
up while the hardware is down etc.
Address this by shutting down everything; we'll run into a
lot of warnings in the process but that's better than having
the whole stack get messed up.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When trying to generate documentation, at least xmldocs, we get the
following warning:
Warning(include/net/cfg80211.h:461): No description found for parameter 'nl80211_iftype'
Fix it by adding the iftype argument name to the
cfg80211_chandef_dfs_required() function declaration.
Reported-and-tested-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This exports a new cfg80211_stop_iface() function.
This is intended for driver internal interface
combination management and channel switching.
Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add locked-version for cfg80211_sched_scan_stopped.
This is used for some users that might want to
call it when rtnl is already locked.
Fixes: d43c6b6 ("mac80211: reschedule sched scan after HW restart")
Cc: stable@vger.kernel.org (3.14+)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends NL80211_CMD_SET_CHANNEL to allow dynamic channel bandwidth
changes in AP mode (including P2P GO) during a lifetime of the BSS. This
can be used to implement, e.g., HT 20/40 MHz co-existence rules on the
2.4 GHz band.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.
When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions. If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.
Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch splits cfg80211_check_combinations()
into an iterator function and a simple iteration
user.
This makes it possible for drivers to asses how
many channels can use given iftype setup. This in
turn can be used for future
multi-interface/multi-channel channel switching.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit a2f73b6c5d ("cfg80211: move regulatory flags to their own variable")
renamed WIPHY_FLAG_CUSTOM_REGULATORY to REGULATORY_CUSTOM_REG, but missed to
update one comment.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counting part of the interface combination check from
cfg80211 to mac80211.
This is needed to simplify locking when the driver has to perform a
combination check by itself (eg. with channel-switch).
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some interface types don't require DFS (such as STATION, P2P_CLIENT
etc). In order to centralize these decisions, make
cfg80211_chandef_dfs_required() take the iftype into consideration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Separate the code that counts the interface types and channels from
the code that check the interface combinations. The new function that
checks for combinations is exported so it can be called by the
drivers.
This is done in preparation for moving the interface combinations
checks out of cfg80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow GO operation on a channel marked with IEEE80211_CHAN_GO_CONCURRENT
iff there is an active station interface that is associated to
an AP operating on the same channel in the 2 GHz band or the same UNII band
(in the 5 GHz band). This relaxation is not allowed if the channel is
marked with IEEE80211_CHAN_RADAR.
Note that this is a permissive approach to the FCC definitions,
that require a clear assessment that the device operating the AP is
an authorized master, i.e., with radar detection and DFS capabilities.
It is assumed that such restrictions are enforced by user space.
Furthermore, it is assumed, that if the conditions that allowed for
the operation of the GO on such a channel change, i.e., the station
interface disconnected from the AP, it is the responsibility of user
space to evacuate the GO from the channel.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FCC are clarifying some soft configuration requirements,
which among other include the following:
1. Indoor operation, where a device can use channels requiring indoor
operation, subject to that it can guarantee indoor operation,
i.e., the device is connected to AC Power or the device is under
the control of a local master that is acting as an AP and is
connected to AC Power.
2. Concurrent GO operation, where devices may instantiate a P2P GO
while they are under the guidance of an authorized master. For example,
on a channel on which a BSS is connected to an authorized master, i.e.,
with DFS and radar detection capability in the UNII band.
See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
Add support for advertising Indoor-only and GO-Concurrent channel
properties.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When dynamically creating interfaces from userspace, e.g. for P2P usage,
such interfaces are usually owned by the process that created them, i.e.
wpa_supplicant. Should wpa_supplicant crash, such interfaces will often
cease operating properly and cause problems on restarting the process.
To avoid this problem, introduce an ownership concept for interfaces. If
an interface is owned by a netlink socket, then it will be destroyed if
the netlink socket is closed for any reason, including if the process it
belongs to crashed. This gives us a race-free way to get rid of any such
interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On 2.4Ghz band, the channels overlap since the delta
between different channels is 5Mhz while the width of the
receiver is 20Mhz (at least).
This means that we can hear beacons or probe responses from
adjacent channels. These frames will have a significant
lower RSSI which will feed all kinds of logic with inaccurate
data. An obvious example is the roaming algorithm that will
think our AP is getting weak and will try to move to another
AP.
In order to avoid this, update the signal only if the frame
has been heard on the same channel as the one advertised by
the AP in its DS / HT IEs.
We refrain from updating the values only if the AP is
already in the BSS list so that we will still have a valid
(but inaccurate) value if the AP was heard on an adjacent
channel only.
To achieve this, stop taking the channel from DS / HT IEs
in mac80211. The DS / HT IEs is taken into account to
discard the frame if it was received on a disabled channel.
This can happen due to the same phenomenon: the frame is
sent on channel 12, but heard on channel 11 while channel
12 can be disabled on certain devices. Since this check
is done in cfg80211, stop even checking this in mac80211.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove unused rx_freq variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send Channel Availability Check time as a parameter
of start_radar_detection() callback.
Get CAC time from regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce DFS CAC time as a regd param, configured per REG_RULE and
set per channel in cfg80211. DFS CAC time is close connected with
regulatory database configuration. Instead of using hardcoded values,
get DFS CAC time form regulatory database. Pass DFS CAC time to user
mode (mainly for iw reg get, iw list, iw info). Allow setting DFS CAC
time via CRDA. Add support for internal regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[rewrap commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ieee80211_iface_limit and the ieee80211_iface_combination
structures to docbook. Reformat the examples of combinations
slightly, so it looks a bit better on docbook.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
docbook (or one of its friends) gets confused with semi-colons in the
argument descriptions, causing it to think that the semi-colon is
marking a new section in the description of addr_mask in wiphy struct.
Prevent this by using hyphens instead of semi-colons in the mask
example.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to userspace assumptions, the sched_scan_stop operation must
be synchronous, i.e. once it returns a new scheduled scan must be
able to start immediately. Document this in the API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It was possible to break interface combinations in
the following way:
combo 1: iftype = AP, num_ifaces = 2, num_chans = 2,
combo 2: iftype = AP, num_ifaces = 1, num_chans = 1, radar = HT20
With the above interface combinations it was
possible to:
step 1. start AP on DFS channel by matching combo 2
step 2. start AP on non-DFS channel by matching combo 1
This was possible beacuse (step 2) did not consider
if other interfaces require radar detection.
The patch changes how cfg80211 tracks channels -
instead of channel itself now a complete chandef
is stored.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.
The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.
Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.
This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.
To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)
To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.
I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow to force SGI, LGI.
Mainly for test purpose.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This required liberally sprinkling 'const' over brcmfmac
and mwifiex but seems like a useful thing to do since the
pointer can't really be written.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Addition of the frequency hints showed up couple of places in cfg80211
where pointers could be marked const and a shared function could be used
to fetch a valid channel.
Signed-off-by: Jouni Malinen <j@w1.fi>
[fix mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
