The Cubieboard4 has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubieboard4 has 2 controllable LEDs, 1 red and 1 green.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A80 SoC has an NMI controller. NMI is an external
interrupt pin exclusely used with PMICs and other system critical
peripherals (such as RTC) in Allwinner's reference designs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A80 dtsi.
Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus board has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A80 SoC has a consumer IR receiver, which is the same as
older SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 has a secondary pin controller. Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The main (24MHz) clock on the A80 is configurable via the PRCM address
space. The low power/speed (32kHz) clock is from an external chip, the
AC100.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the supported PRCM clocks and reset controls to the A80 dtsi.
The DAUDIO module clocks are not supported yet.
Also update clock and reset phandles for r_uart.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the touchscreen found on the pov protab2-ips9
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the touchscreen controller used on the iNet1 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the on-chip audio codec
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the on-chip audio codec
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the AXP152 pmic used on Auxtek T004 boards.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Michael van Slingerland <michael@deviousops.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the lcd panel backlight on the pov protab2 ips9
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the lcd panel backlight on the UTOO P66 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the lcd panel backlight on the iNet1 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The iNet1 tablet uses the A10's integrated audio codec, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.
Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Gemei G9 has internal speakers and headphone jack. Audio switching
from internal speakers to headphones is automatically handled by
extra FT2012Q audio amplifier chip that works out of the box.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
ADC seems to be using ldo2 for reference voltage.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add regulator nodes for axp209 using the axp209.dtsi include.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet9f-rev03 tablet has multiple fire-buttons / direction controls,
add support for these using the same axis mapping as ps2 compatible game
controllers with the same stick / button layout use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the on-chip audio codec
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable on-chip audio codec on the Wexler TAB7200 tablet.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the on-chip audio codec on the Olimex A20-SOM-EVB
Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the axp221 PMIC chip in the dts file.
Allows board to power off correctly from the poweroff command
This board requires dc1sw to be enabled in order to provide a power source
for the 5V DCDC converter that powers USB2.
This board uses dldo1 for 3.3V wifi power
This board requires dldo3 to be enabled at 2.8V in order to provide voltage
to the pullup resistors for the i2c0 bus.
Signed-off-by: Lawrence Yu <lyu@micile.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This baseboard from SWAC is equipped with the ICnova-A20 SoM from
Incircuit. This board is equipped with the following interfaces /
devices:
- 512 MiB SDRAM
- 4 GiB MLC NAND (Micron MT29F32G08CBACAWP or Hynix H27UBG8T2BTR)
- USB host
- LCD 800x480
- HDMI
- CAN
Note that the NAND support is still missing. As its currently not
supported in mainline for sunxi and especially for these MLC
devices.
The original plan was to also provide a dtsi for the ICnova SoM,
to put all the SoM internal nodes / properties there. But as I
don't have a clear overview of the SoM specific and baseboard
specific differences, I'm putting all in one dts for now. Once
somebody pushed support for some other baseboard using the
A20 SoM from Incircuit (e.g. the ADB4006 reference design), this
should be separated.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marcus Heuer <marcus.heuer@swac.de>
[maxime: Fixed CPU regulator upper voltage boundary]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pcDuino V3 Nano has a 3.5mm TRRS jack socket for audio, using the
CTIA standard pinout, connected to HPOUTL, HPOUTR, HPCOM/HPCOMFB and
MICIN1/VMIC (via appropriate RC networks) on the A20. The PH00 GPIO is
wired for headphone plug detection: it reads 0 when nothing's plugged
in, and 1 when a plug is inserted.
LINEINL/R and FMINL/R are not connected.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
As we've enabled multiplatform kernels on ARM, and greatly done away with
the contents under arch/arm/mach-*, there's still need for SoC-related
drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate
with power management blocks on these SoCs for use by clock, regulator and
bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be confused with
PSCI (Power State Coordination Interface). SCPI is used to communicate with
the assistant embedded cores doing power management, and we have yet to see
how many of them will implement this for their hardware vs abstracting in
other ways (or not at all like in the past).
- To make confusion between SCPI and PSCI more likely, this release also
includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dm+I
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"As we've enabled multiplatform kernels on ARM, and greatly done away
with the contents under arch/arm/mach-*, there's still need for
SoC-related drivers to go somewhere.
Many of them go in through other driver trees, but we still have
drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code
that might be shared between ARM and ARM64 (or just in general makes
sense to not have under the architecture directory).
This branch contains mostly such code:
- Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to
communicate with power management blocks on these SoCs for use by
clock, regulator and bus frequency drivers.
- Allwinner Reduced Serial Bus driver, again used to communicate with
PMICs.
- Drivers for ARM's SCPI (System Control Processor). Not to be
confused with PSCI (Power State Coordination Interface). SCPI is
used to communicate with the assistant embedded cores doing power
management, and we have yet to see how many of them will implement
this for their hardware vs abstracting in other ways (or not at all
like in the past).
- To make confusion between SCPI and PSCI more likely, this release
also includes an update of PSCI to interface version 1.0.
- Rockchip support for power domains.
- A driver to talk to the firmware on Raspberry Pi"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits)
soc: qcom: smd-rpm: Correct size of outgoing message
bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus
bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings
ARM: bcm2835: add mutual inclusion protection
drivers: psci: make PSCI 1.0 functions initialization version dependent
dt-bindings: Correct paths in Rockchip power domains binding document
soc: rockchip: power-domain: don't try to print the clock name in error case
soc: qcom/smem: add HWSPINLOCK dependency
clk: berlin: add cpuclk
ARM: berlin: dts: add CLKID_CPU for BG2Q
ARM: bcm2835: Add the Raspberry Pi firmware driver
soc: qcom: smem: Move RPM message ram out of smem DT node
soc: qcom: smd-rpm: Correct the active vs sleep state flagging
soc: qcom: smd: delete unneeded of_node_put
firmware: qcom-scm: build for correct architecture level
soc: qcom: smd: Correct SMEM items for upper channels
qcom-scm: add missing prototype for qcom_scm_is_available()
qcom-scm: fix endianess issue in __qcom_scm_is_call_available
soc: qcom: smd: Reject send of too big packets
soc: qcom: smd: Handle big endian CPUs
...
Again we have a sizable (but not huge) cleanup branch with a net delta of about
-3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now gone
completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the above are
the major pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uI7R
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
Merging in the few patches I had kept separate from main next/dt, since others
got merged here directly.
* next/arm64:
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
arm64: dts: mt8173: Add clocks for SCPSYS unit
arm64: dts: mt8173: Add subsystem clock controller device nodes
+ Linux 4.3-rc5
Just a single revert for a patch, that I should not have queued.
Detailed description is inside the patch. It's totally my fault,
that this happened, sorry about that :(
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E1FO
-----END PGP SIGNATURE-----
Merge tag 'for-v4.4-important-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fix from Sebastian Reichel:
"Just a single revert for a patch, that I should not have queued.
Detailed description is inside the patch. It's totally my fault, that
this happened, sorry about that :("
* tag 'for-v4.4-important-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
Revert "ARM: dts: twl4030: Add iio properties for bci subnode"
This reverts commit af19161aae,
which breaks the omap3 device tree build due to a wrong reference.
I accidently queued this change via the power supply subsystem while
telling Marek at the same time, that it should go through Tony.
Following that I did miss Stephen's messages about the build failure in
linux-next and since he switched to merging an older snapshot nobody
else noticed the problem in my tree. I didn't notice myself, since I
did not build any device tree files assuming none have changed by me.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reported-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all dtbs
in the tree for most arches with dts files (except powerpc for now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tGCy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A fairly large (by DT standards) pull request this time with the
majority being some overdue moving DT binding docs around to
consolidate similar bindings.
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all
dtbs in the tree for most arches with dts files (except powerpc for
now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options"
* tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
MAINTAINERS: update DT binding doc locations
devicetree: add Sigma Designs vendor prefix
of: simplify arch_find_n_match_cpu_physical_id() function
Documentation: arm: Fixed typo in socfpga fpga mgr example
Documentation: devicetree: fix reference to legacy wakeup properties
Documentation: devicetree: standardize/consolidate on "wakeup-source" property
drivers: of: removing assignment of 0 to static variable
xtensa: enable building of all dtbs
mips: enable building of all dtbs
metag: enable building of all dtbs
metag: use common make variables for dtb builds
h8300: enable building of all dtbs
arm64: enable building of all dtbs
arm: enable building of all dtbs
arc: enable building of all dtbs
arc: use common make variables for dtb builds
of: add config option to enable building of all dtbs
of/fdt: fix error checking for earlycon address
of/overlay: add missing of_node_put
of/platform: add missing of_node_put
...
Pull input updates from Dmitry Torokhov:
"Items of note:
- evdev users can now limit or mask the kind of events they will
receive. This will allow applications such as power manager or
network manager to only be woken when user presses special keys
such as KEY_POWER or KEY_WIFI and not be bothered with ordinary
key presses coming from keyboard
- support for FocalTech FT6236 touchscreen controller
- support for ROHM BU21023/24 touchscreen controller
- edt-ft5x06 touchscreen driver got a face lift and can now be used
with FT5506
- support for Google Fiber TV Box remote controls
- improvements in xpad driver (with more to come)
- several parport-based drivers have been switched to the new device
model
- other miscellaneous driver improvements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (70 commits)
HID: hid-gfrm: avoid warning for input_configured API change
HID: hid-input: allow input_configured callback return errors
Input: evdev - fix bug in checking duplicate clock change request
Input: add userio module
Input: evdev - add event-mask API
Input: snvs_pwrkey - remove duplicated semicolon
HID: hid-gfrm: Google Fiber TV Box remote controls
Input: e3x0-button - update Kconfig description
Input: tegra-kbc - drop use of IRQF_NO_SUSPEND flag
Input: tegra-kbc - enable support for the standard "wakeup-source" property
Input: xen - check return value of xenbus_printf
Input: hp_sdc_rtc - fix y2038 problem in proc_show
Input: nomadik-ske-keypad - fix a trivial typo
Input: xpad - fix clash of presence handling with LED setting
Input: edt-ft5x06 - work around FT5506 firmware bug
Input: edt-ft5x06 - add support for FT5506
Input: edt-ft5x06 - add support for different max support points
Input: edt-ft5x06 - use max support points to determine how much to read
Input: rotary-encoder - add support for quarter-period mode
Input: rotary-encoder - use of_property_read_bool
...
Here is the big char/misc driver update for 4.4-rc1. Lots of different
driver and subsystem updates, hwtracing being the largest with the
addition of some new platforms that are now supported. Full details in
the shortlog.
All of these have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6d/oACgkQMUfUDdst+yl93ACcCf91y+ufwU3cmcnq5LpwHPfx
VbkAn08Cn6Wu6IcihoEpR4hqGgIOtjqW
=1a3d
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.4-rc1. Lots of
different driver and subsystem updates, hwtracing being the largest
with the addition of some new platforms that are now supported. Full
details in the shortlog.
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (181 commits)
fpga: socfpga: Fix check of return value of devm_request_irq
lkdtm: fix ACCESS_USERSPACE test
mcb: Destroy IDA on module unload
mcb: Do not return zero on error path in mcb_pci_probe()
mei: bus: set the device name before running fixup
mei: bus: use correct lock ordering
mei: Fix debugfs filename in error output
char: ipmi: ipmi_ssif: Replace timeval with timespec64
fpga: zynq-fpga: Fix issue with drvdata being overwritten.
fpga manager: remove unnecessary null pointer checks
fpga manager: ensure lifetime with of_fpga_mgr_get
fpga: zynq-fpga: Change fw format to handle bin instead of bit.
fpga: zynq-fpga: Fix unbalanced clock handling
misc: sram: partition base address belongs to __iomem space
coresight: etm3x: adding documentation for sysFS's cpu interface
vme: 8-bit status/id takes 256 values, not 255
fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000
ARM: zynq: dt: Updated devicetree for Zynq 7000 platform.
ARM: dt: fpga: Added binding docs for Xilinx Zynq FPGA manager.
ver_linux: proc/modules, limit text processing to 'sed'
...
Pull networking updates from David Miller:
Changes of note:
1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.
2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
David Ahern.
3) Allow the user to ask for the statistics to be filtered out of
ipv4/ipv6 address netlink dumps. From Sowmini Varadhan.
4) More work to pass the network namespace context around deep into
various packet path APIs, starting with the netfilter hooks. From
Eric W Biederman.
5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
Richter.
6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.
7) Support Very High Throughput in wireless MESH code, from Bob
Copeland.
8) Allow setting the ageing_time in switchdev/rocker. From Scott
Feldman.
9) Properly autoload L2TP type modules, from Stephen Hemminger.
10) Fix and enable offload features by default in 8139cp driver, from
David Woodhouse.
11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
Jiri Benc.
12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
Opstad.
13) Fix IPSEC flowcache overflows on large systems, from Steffen
Klassert.
14) Convert bridging to track VLANs using rhashtable entries rather than
a bitmap. From Nikolay Aleksandrov.
15) Make TCP listener handling completely lockless, this is a major
accomplishment. Incoming request sockets now live in the
established hash table just like any other socket too.
From Eric Dumazet.
15) Provide more bridging attributes to netlink, from Nikolay
Aleksandrov.
16) Use hash based algorithm for ipv4 multipath routing, this was very
long overdue. From Peter Nørlund.
17) Several y2038 cures, mostly avoiding timespec. From Arnd Bergmann.
18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.
19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet. This
influences the port binding selection logic used by SO_REUSEPORT.
20) Add ipv6 support to VRF, from David Ahern.
21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.
22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.
23) Implement RACK loss recovery in TCP, from Yuchung Cheng.
24) Support multipath routes in MPLS, from Roopa Prabhu.
25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
Dumazet.
26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
Sudarsana Kalluru.
27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
Sowa.
28) Support ipv6 geneve tunnels, from John W Linville.
29) Add flood control support to switchdev layer, from Ido Schimmel.
30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
Hannes Frederic Sowa.
31) Support persistent maps and progs in bpf, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
sh_eth: use DMA barriers
switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
net: sched: kill dead code in sch_choke.c
irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
net: dsa: mv88e6xxx: include DSA ports in VLANs
net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
net/core: fix for_each_netdev_feature
vlan: Invoke driver vlan hooks only if device is present
arcnet/com20020: add LEDS_CLASS dependency
bpf, verifier: annotate verbose printer with __printf
dp83640: Only wait for timestamps for packets with timestamping enabled.
ptp: Change ptp_class to a proper bitmask
dp83640: Prune rx timestamp list before reading from it
dp83640: Delay scheduled work.
dp83640: Include hash in timestamp/packet matching
ipv6: fix tunnel error handling
net/mlx5e: Fix LSO vlan insertion
net/mlx5e: Re-eanble client vlan TX acceleration
net/mlx5e: Return error in case mlx5e_set_features() fails
net/mlx5e: Don't allow more than max supported channels
...
Pull crypto update from Herbert Xu:
"API:
- Add support for cipher output IVs in testmgr
- Add missing crypto_ahash_blocksize helper
- Mark authenc and des ciphers as not allowed under FIPS.
Algorithms:
- Add CRC support to 842 compression
- Add keywrap algorithm
- A number of changes to the akcipher interface:
+ Separate functions for setting public/private keys.
+ Use SG lists.
Drivers:
- Add Intel SHA Extension optimised SHA1 and SHA256
- Use dma_map_sg instead of custom functions in crypto drivers
- Add support for STM32 RNG
- Add support for ST RNG
- Add Device Tree support to exynos RNG driver
- Add support for mxs-dcp crypto device on MX6SL
- Add xts(aes) support to caam
- Add ctr(aes) and xts(aes) support to qat
- A large set of fixes from Russell King for the marvell/cesa driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (115 commits)
crypto: asymmetric_keys - Fix unaligned access in x509_get_sig_params()
crypto: akcipher - Don't #include crypto/public_key.h as the contents aren't used
hwrng: exynos - Add Device Tree support
hwrng: exynos - Fix missing configuration after suspend to RAM
hwrng: exynos - Add timeout for waiting on init done
dt-bindings: rng: Describe Exynos4 PRNG bindings
crypto: marvell/cesa - use __le32 for hardware descriptors
crypto: marvell/cesa - fix missing cpu_to_le32() in mv_cesa_dma_add_op()
crypto: marvell/cesa - use memcpy_fromio()/memcpy_toio()
crypto: marvell/cesa - use gfp_t for gfp flags
crypto: marvell/cesa - use dma_addr_t for cur_dma
crypto: marvell/cesa - use readl_relaxed()/writel_relaxed()
crypto: caam - fix indentation of close braces
crypto: caam - only export the state we really need to export
crypto: caam - fix non-block aligned hash calculation
crypto: caam - avoid needlessly saving and restoring caam_hash_ctx
crypto: caam - print errno code when hash registration fails
crypto: marvell/cesa - fix memory leak
crypto: marvell/cesa - fix first-fragment handling in mv_cesa_ahash_dma_last_req()
crypto: marvell/cesa - rearrange handling for sw padded hashes
...
- Add 'invert' sysfs attribute to the heartbeat trigger.
- Add Device Tree support to the leds-netxbig driver and add
related DT nodes to the kirkwood-netxbig.dtsi and kirkwood-net5big.dts
files. Remove static LED setup from the related board files.
- Remove redundant brightness conversion operation from leds-netxbig.
- Improve leds-bcm6328 driver: improve default-state handling, add more
init configuration options, print invalid LED instead of warning only
about maximum LED value.
- Add a shutdown function for setting gpio-leds into off state
when shutting down.
- Fix DT flash timeout property naming in leds-aat1290.txt.
- Switch to using devm prefixed version of led_classdev_register()
(leds-cobalt-qube, leds-hp6xx, leds-ot200, leds-ipaq-micro,
leds-netxbig, leds-locomo, leds-menf21bmc, leds-net48xx,
leds-wrap).
- Add missing of_node_put (leds-powernv, leds-bcm6358, leds-bcm6328,
leds-88pm860x).
- Coding style fixes and cleanups: led-class/led-core, leds-ipaq-micro.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)
iQIcBAABAgAGBQJWOGwiAAoJEL1qUBy3i3wm72QQANGvr2lx7YgpLx0BjtkvKlBN
CVVHE3u4DhZoiMusJ0qcMO2mGyjd6yJe9rfv3UchA2H7+OooJl401m9niZBrsJGW
2WIOTI1IpJOPD+WaKdxX/Fg3s76UU4hOcsDPxEyKjdJY9pmk6rUkpkDPAS7GoyCH
fhjCByhMT0JHN1Md5+vSx8heMWPcn/3b0RHSMJg9ZZZNi+vCLRiCRMOVYqtZxh6R
P4HLHXfU45dVtBeikD1Thlq7BvaRyOpWASJwCF2Jar/xKZYPrlXeTn3xaMgVa4ls
3fZFcerib3JBR0B1Y9oguhGepd/N7YXacSuxg3TJu4xSd1GzdT9id19hYftHwj7T
NYxImgXLV92stQInCn1L18OUFtvdgO0xJSszCZwUvup4BtJKU1kyFBQ8fouRUimr
8FTYCgwO8F7/zpFeJcKIgwTKZ8XFjzyehM5lXZBxK+mQh69IT2qqY0klqc4xKynr
CFSG/PUWQt3iYXM/D/q7vRphykMqicjwHSgaDDGGDDov+VmUdvRxxVveH74oWFre
2LvOAeVo42Abl5h+An7KHXZGzxWUs3XpDXOthd77NISNnK3sw43hBAw782GjwM95
0/tdXGvOsMMPUSjR9StHSkn6rQipW0q606nqmXr0VnSuJA1yLr3GNL0j4A75ULxM
Qoj/sW7Gzb+ZmN78Pg4y
=X8+e
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- Move the out-of-LED-tree led-sead3 driver to the LED subsystem.
- Add 'invert' sysfs attribute to the heartbeat trigger.
- Add Device Tree support to the leds-netxbig driver and add related DT
nodes to the kirkwood-netxbig.dtsi and kirkwood-net5big.dts files.
Remove static LED setup from the related board files.
- Remove redundant brightness conversion operation from leds-netxbig.
- Improve leds-bcm6328 driver: improve default-state handling, add more
init configuration options, print invalid LED instead of warning only
about maximum LED value.
- Add a shutdown function for setting gpio-leds into off state when
shutting down.
- Fix DT flash timeout property naming in leds-aat1290.txt.
- Switch to using devm prefixed version of led_classdev_register()
(leds-cobalt-qube, leds-hp6xx, leds-ot200, leds-ipaq-micro,
leds-netxbig, leds-locomo, leds-menf21bmc, leds-net48xx, leds-wrap).
- Add missing of_node_put (leds-powernv, leds-bcm6358, leds-bcm6328,
leds-88pm860x).
- Coding style fixes and cleanups: led-class/led-core, leds-ipaq-micro.
* tag 'leds_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (27 commits)
leds: 88pm860x: add missing of_node_put
leds: bcm6328: add missing of_node_put
leds: bcm6358: add missing of_node_put
powerpc/powernv: add missing of_node_put
leds: leds-wrap.c: Use devm_led_classdev_register
leds: aat1290: Fix property naming of flash-timeout-us
leds: leds-net48xx: Use devm_led_classdev_register
leds: leds-menf21bmc.c: Use devm_led_class_register
leds: leds-locomo.c: Use devm_led_classdev_register
leds: leds-gpio: add shutdown function
Documentation: leds: update DT bindings for leds-bcm6328
leds-bcm6328: add more init configuration options
leds-bcm6328: simplify and improve default-state handling
leds-bcm6328: print invalid LED
leds: netxbig: set led_classdev max_brightness
leds: netxbig: convert to use the devm_ functions
ARM: mvebu: remove static LED setup for netxbig boards
ARM: Kirkwood: add LED DT entries for netxbig boards
leds: netxbig: add device tree binding
leds: triggers: add invert to heartbeat
...
