The recent commit "ARM: EXYNOS: add support for EXYNOS5440 SoC" broke
support for exynos5250 because of_machine_is_compatible() was used too
early in the boot process. It also probably meant that the exynos5440
failed to use the proper iotable. Switch to use
of_flat_dt_is_compatible() in both of these cases.
The failure I was seeing in exynos5250 because of this was:
Division by zero in kernel.
[<80015ed4>] (unwind_backtrace+0x0/0xec) from [<8045c7a4>] (dump_stack+0x20/0x24)
[<8045c7a4>] (dump_stack+0x20/0x24) from [<80012990>] (__div0+0x20/0x28)
[<80012990>] (__div0+0x20/0x28) from [<8021ab04>] (Ldiv0_64+0x8/0x18)
[<8021ab04>] (Ldiv0_64+0x8/0x18) from [<80068560>] (__clocksource_updatefreq_scale+0x54/0x134)
[<80068560>] (__clocksource_updatefreq_scale+0x54/0x134) from [<8006865c>] (__clocksource_register_scale+0x1c/0x54)
[<8006865c>] (__clocksource_register_scale+0x1c/0x54) from [<80612a18>] (exynos_timer_init+0x100/0x1e8)
[<80612a18>] (exynos_timer_init+0x100/0x1e8) from [<8060d184>] (time_init+0x28/0x38)
[<8060d184>] (time_init+0x28/0x38) from [<8060a754>] (start_kernel+0x1e0/0x3c8)
[<8060a754>] (start_kernel+0x1e0/0x3c8) from [<40008078>] (0x40008078)
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
[olofj: fixed two build errors, one missing include and one !CONFIG_OF failure]
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the registers used to configure the CSI-2 receiver PHY on OMAP3430 and
3630 and map them in the ISP driver. The register is part of the control
block but it only is needed by the ISP driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SP804 driver statically initialises the cpumask of the clock event
device to be cpu_all_mask, which is derived from the compile-time
constant NR_CPUS. This breaks SMP_ON_UP systems where the interrupt
controller handling the sp804 doesn't have the irq_set_affinity callback
on the irq_chip, because the common timer code fails to identify the
device as cpu-local and ends up treating it as a broadcast device
instead.
This patch fixes the problem by using cpu_possible_mask at runtime,
which will correctly represent the possible CPUs when SMP_ON_UP is being
used.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
Add missing PL330 MDMA1 controller node to the device tree (DT).
[ Currently there is no problem with using 'non-secure' mdma1 address
instead of 'secure' one on revision 0 of Exynos4210 SOC (as used by
Universal C210 board) as this SOC revision is unsupported by DT. ]
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos4412 uses different information register for each core. This
patch adjusts the bring-up code to take that into account.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for using UART3 for DEBUG_LL on exynos.
[dianders: added depend on ARCH_EXYNOS.]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The s3c-camif driver uses "camera" clock conn_id for the "camif-upll"
(s3c244x) and "camera" (s3c64xx) platform clock. By adding this new
clkdev entry the platform differences are isolated from the driver.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds default helper functions for the camera port
pin configuration. Whenever pinctrl support for s3c24xx/s3c64xx
SoCs is available these code should be removed and proper pinctrl
API should be used in the CAMIF driver.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With device tree support enabled for dwmci controller, the unused
non-dt support for dwmci controller can be removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
[kgene.kim@samsung.com: updated as per Seungwon Jeon's pointing out]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The core cpu_suspend code no longer calls flush_cache_all to
optimize the cpu idle flow. Add a call for the same in the
exynos specific suspend code.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cortex A9 based exynos4 has a memory mapped SCU while the Cortex
A15 based exynos5 does not. Hence, remove the call to scu_enable
for exynos5.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Inderpal Singh <inderpal.singh@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Upon wake-up, clear the sleep mode set in INFORM1 register.
Signed-off-by: Inderpal Singh <inderpal.singh@samsung.com>
Tested-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Set the gic arch extension callback to support rtc wakeup.
Signed-off-by: Inderpal Singh <inderpal.singh@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sequence of cpu_enter_lowpower() for Cortex-A15 is
different from the sequence for Cortex-A9. This patch
implements cpu_enter_lowpower() for EXYNOS5 SoC which
has Cortex-A15 cores.
Basded on original patch has been submitted by Changhwan Youn
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
[kgene.kim@samsung.com: use flush_cache_louis() instead of
flush_cache_all() as per Lorenzo and Santosh's suggestion]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These are not actually connected but it saves them going through probe
deferral.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
From Lee Jones <lee.jones@linaro.org>:
* 'ste-dt-for-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
This follows up on the previous ux500 DT changes. Most importantly, it
resolves a build error in the dts files that was the result of referring
to a board specific device node from the common dtsi file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cpufreq driver doesn't only handle the db8500 anymore. There
are new variants which rely on it too, so we've renamed the
driver to be more generic.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds hrefprev60, hrefv60plus and ccu9540 to device trees compiled
during build.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
We now initialise the PCM driver through the MSP DAI, so there is
no need to register it though platform code anymore. This patch
strips out all PCM platform registration.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
GPIO numbers for the newly created gpio-regulator will differ from
board to board. Therefore it's not sensible to leave this information
in the top level DTSI file. Let's move them out to the DTS files
where they can correctly vary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Not all supported boards will require a MMCI gpio-regulator,
therefore it's a good idea to only enable the node when and if
it is required. Let's disable it by default.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull ARM fixes from Russell King:
"Not much here, just a couple minor/cosmetic fixes and a patch for the
decompressor which fixes problems with modern GCC and CPUs."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7583/1: decompressor: Enable unaligned memory access for v6 and above
ARM: 7572/1: proc-v6.S: fix comment
ARM: 7570/1: quiet down the non make -s output
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zpgo
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/cleanup
From Linus Walleij <linus.walleij@linaro.org>:
This series will do the following:
- Switch the Integrator/AP and /CP to use the SoC bus
when booting from device tree.
- Group all devices on the SoC below this bus so as to
set a good example of how to do this. The bus was
invented by Lee Jones, let's show how it's to be used
on a DT:ed SoC.
- Fetch the special system controller offsets from two
special device tree nodes for each case and replace
the static mappings with these at boot.
- Move some static remaps to the ATAG-only code path
and delete some static maps that aren't used.
- Push dependencies on system controller remaps down
to the Integrator/AP board file and the PCIv3 driver
respectively and use only dynamic remappings.
- Fix up conditional BUG() usage in the PCIv3 driver
to be simpler and more to the point.
* tag 'integrator-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
ARM: integrator: hook the CP into the SoC bus
ARM: integrator: hook the AP into the SoC bus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Patch f055f1f6 [ARM: sunxi: Add sun4i and cubieboard support] missed
this sun4i.dtsi include file. This patch finally brings it upstream
enabling support for sun4i boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Correct option should be LEDS_TRIGGERS, not LEDS_TRIGGER.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The kvm_seq value has nothing to do what so ever with this other KVM.
Given that KVM support on ARM is imminent, it's best to rename kvm_seq
into something else to clearly identify what it is about i.e. a sequence
number for vmalloc section mappings.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves shirq interrupt controllers driver and header file out of
plat-spear directory. It is moved to drivers/irqchip/ directory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
shirq layer has been adapted to DT, add corresponding nodes in all
SPEAr3xx variants.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
SPEAr3xx architecture includes shared/multiplexed irqs for certain set
of devices. The multiplexor provides a single interrupt to parent
interrupt controller (VIC) on behalf of a group of devices.
There can be multiple groups available on SPEAr3xx variants but not
exceeding 4. The number of devices in a group can differ, further they
may share same set of status/mask registers spanning across different
bit masks. Also in some cases the group may not have enable or other
registers. This makes software little complex.
Present implementation was non-DT and had few complex data structures to
decipher banks, number of irqs supported, mask and registers involved.
This patch simplifies the overall design and convert it in to DT. It
also removes all registration from individual SoC files and bring them
in to common shirq.c.
Also updated the corresponding documentation for DT binding of shirq.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch fixes the platform data for compact flash controller.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Few fields are not required to be programmed in platform data of spi controller
now, as it comes via DT. Remove them.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch moves some global macro definitions to the files where they are used.
Its a step towards removing spear.h completely later on.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
amba-pl011 driver supports two pin state "default" and "sleep" and it
expect from dt to provide this pinctrl states and phandler otherwise it
gives a warning message.
To remove this warning message pass default state with null phandler to uart
pins in device node (In our case all the pins are configured in default states
so we pass null phandler to pins).
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch modifies the DT bindings for the GMAC IP existings for the
SPEAr family. The DT bindings now additionally pass the phy mode as a
configuration parameter for the ethernet device.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
SPEAr platform provides a provision to control chipselects of ARM PL022 Prime
Cell spi controller through its system registers, which otherwise remains under
PL022 control which some protocols do not want.
This patch adds spics controller nodes in device tree for various SPEAr13xx
SoCs.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Merge in orion's cleanup branch together with the DT contents. Ideally
the cleanup branch should have been the base for the DT branch to avoid
these, but that was missed when first merging. So we're doing it now to
reduce the amount of silly conflicts due to internal tree organization.
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge in the cleanups that should have been used as the base of the DT
branch instead of letting the conflicts be exposed all the way up to
the toplevel merges.
All of these are caused by cleanups being done both in the cleanup branch
and the dt branch, resulting in remove/remove conflicts of header files.
By Andrew Lunn (3) and others
via Jason Cooper
* orion/cleanup:
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
Remove/remove conflicts in:
arch/arm/mach-kirkwood/board-dockstar.c
arch/arm/mach-kirkwood/board-goflexnet.c
arch/arm/mach-kirkwood/board-lsxl.c
Signed-off-by: Olof Johansson <olof@lixom.net>
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQsEfdAAoJEAi3KVZQDZAeBd8IAIAkBGIJyUJSmQJEWkZ/9ezq
UOLec1t/TnLhAQ1Sk8g4C41wmHKYNqmZSVaAXC+QP6Yw+Gdhlw+V6YBjOYDzA7Y4
k8ljw3SFbvS+AIx0qK26j6Tf6En2H5lMXsdlKoarCV+G+MxAHsQO7jL6y7BFwTlX
QnwJFz+NRzMFxaPiCS+43oZuxIIzkHe8wKMb0y7nSiNQYUUv8TdKvyK+ekFuszOp
v6uo/MI1p1/xdUxDbEKxOwmUjAy7x+t0LUFi1dsWuiDHdrG+BVT4NkJuFaD8Ui13
VoUD1ogyWHQZV2hq0dfj+9Hed5NEgl6toAzGN9LPLmsuVUXCnB2CdBprhuDv5F8=
=yaX1
-----END PGP SIGNATURE-----
Merge tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
orion dt for v3.8
- ehci-orion dt binding
- gpio-poweroff
- use dt regulators
- move mpp to DT/pinctrl
Depends on:
- orion/boards
- merge conflicts
- keep all 'select's in Kconfig
- remove all #includes in board-*.c
- pinctrl/devel up to:
- 06763c7 pinctrl: mvebu: move to its own directory
* tag 'orion_dt_for_3.8' of git://git.infradead.org/users/jcooper/linux: (211 commits)
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
ARM: Kirkwood: Convert dnskw to pinctrl
ARM: Kirkwood: Convert iConnect to pinctrl.
ARM: Kirkwood: Convert TS219 to pinctrl.
ARM: Kirkwood: Add DTSI files for pinctrl
ARM: Kirkwood: Make use of mvebu pincltl and gpio drivers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrc/qAAoJEAi3KVZQDZAeGIcIAJ70hcz/cKdEKNpekMRoMWpz
LoDXtPqRuUvCqBdUNFkJyPAhHHkWwnU6KRcBRz1dknTtJ7nyCkDQYRG/JIroIs8I
X9N6JbPH7FMU+Z1ZUAM2ww+pEAIQkwX06erAy9u/a7ivMj/0LeXboNK+ngIx1jgL
xz2SS4wJrujPwvT2rYo4nJ+WwGiiIPbRjiY7r87rD/DQ9nY9DxKgfve7pRhaCCZS
Baw48u8qTe6M9LGcXw+b/MSHGCTB6YabqaRHMAr/1NK0Z3JDGU8tEpOuMCnFX7SA
6CxEymw5/8fzyTgdRz7FRd9Hg28y5Cd+T2l48X4tSL/M16H4EeBOxj6ub4zCi9s=
=nsDw
-----END PGP SIGNATURE-----
Merge tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/boards
From Jason Cooper:
orion boards for v3.8
- mach-orion5x/ joins the dark side! (devicetree)
- Lacie Network Space family
- Lacie Ethernet Disk mini v2
- USI TopKick
- ZyXEL NSA310
- MPL CEC4
- Plat'Home OpenBlocks A6 (kirkwood, AX3-4 is armada xp)
* tag 'orion_boards_for_3.8' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
- remove unused includes in kirkwood
- fix sparse warnings in kirkwood
- checkpatch cleanup in kirkwood
- use common code in pcie on kirkwood
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQrbKoAAoJEAi3KVZQDZAeojYH/0m7nrIMrLQ1A9FjglAzZQrE
Q7UrP4HWlTnG+aNF4a0G4CpO+vZYJd6mSKW3kP18AuncCK5hylAPdHyGRWT+RLQg
BCKVib2S/Gxqh3Qc9Re6vReKN5icyzYkB0Sv6/kpBLqfx3f7d1WJPUyA+RsCQhBn
crp7rYOBK3vcmRjgrrzCkyNzsTHt6pCfQio3uCru34gCCHZpellZLGzMScVpuQqM
LO9WVJTBe1RSRXej+StutcPR/5sy7yjKrA2y42tAmqKTPgzCdcXsbc2BqQRNZ4X2
UzXAYOMLr2BK43t68DBaX2QGy4AxWqgCqCKpoWwjBEtAD5mh/X+NAbs7kyUov3c=
=JCyB
-----END PGP SIGNATURE-----
Merge tag 'orion_cleanup_for_3.8' of git://git.infradead.org/users/jcooper/linux into next/cleanup
From Jason Cooper:
orion cleanup for v3.8
- remove unused includes in kirkwood
- fix sparse warnings in kirkwood
- checkpatch cleanup in kirkwood
- use common code in pcie on kirkwood
* tag 'orion_cleanup_for_3.8' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
From Kukjin Kim:
This is adding support for exynos5440, including Quad ARM Cortex-A15
cores and its reference board SSDK5440.
Note, at this moment, just enabled minimal system part for initial kernel
boot and pinctrl driver.
* 'next/soc-exynos5440' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add pin controller node for Samsung EXYNOS5440 SoC
pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC
ARM: dts: add initial dts file for EXYNOS5440, SSDK5440
ARM: EXYNOS: add support for EXYNOS5440 SoC
Add/add conflict in arch/arm/boot/dts/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is second Samsung DT stuff for v3.8.
This is including power domain DT support for exynos and Google ARM
Chromebook, Snow board and exynos4210-origen updates.
* 'next/dt-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Use drive strength 3 for SD pins for exynos4
ARM: dts: Set up power domains for exynos4
ARM: EXYNOS: Bind devices to power domains using DT
ARM: EXYNOS: Fix power domain name initialization
ARM: EXYNOS: Detect power domain state on registration from DT
ARM: dts: Add vmmc fixed voltage regulator for exynos4210-origen
ARM: dts: Update sdhci nodes for current bindings for exynos4210-origen
ARM: dts: Update for pinctrl-samsung driver for exynos4210-origen
ARM: dts: Split memory sections for exynos4210-origen
ARM: EXYNOS: add all i2c busses to auxdata for DT
ARM: dts: Add aliases for i2c controller for exynos4
ARM: dts: Add board dts file for Snow board (ARM Chromebook)
ARM: dts: Move the dwmmc aliases from smdk5250 dts to exynos
Add/add conflicts resolved in arch/arm/boot/dts/exynos5250-smdk5250.dts
and arch/arm/mach-exynos/mach-exynos5-dt.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=IZiZ
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer:
ARM i.MX SoC updates for v3.8
* tag 'imx-soc-1' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
Signed-off-by: Olof Johansson <olof@lixom.net>
them as the second mxs/dt pull request for 3.8. Please consider to
pull.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQreEpAAoJEFBXWFqHsHzOem0H/A+agUbLlYNT1Uxc8L6eq0Fg
DkY/BMHoCqlG1+/Yr7nrkTxBWbWTqEfU+DcKyDZrW25CXvNA1WRT3qwfTWC0FxqH
SxXlnyDYa4iHsc63EJVltBoiw3ojN7vhbA41Pp3qGD7h8f+j9RVVxl0HuxwCYsI2
pf141gqFZbB2qiskQUCdfR4E2YKri+SoMXPcLCW+cIyO2UOD1URuAHCPcC/t2vuJ
y1oRvTZCM8UQavfQYG1tpNfUzB79n25vfsL1zTRw8+vp7c9bZzJKbCfWraqfQI8K
ufy21eqNpTAotiknfLySu4JRgiBuv1OL7t5kF7n1jo0w/KV50zRfEIlLGiKtxmA=
=XFM8
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
They are a few mxs dts updates coming a little bit late. I'm sending
them as the second mxs/dt pull request for 3.8. Please consider to
pull.
* tag 'mxs-dt-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: mxs: add oled support for the cfa-10036
ARM: mxs: Add SchulerControl SPS1 DTS file
ARM: imx23-olinuxino: Add spi support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
OpenBlocks A6 has three leds via GPIO. This supports them.
And this fix typo about led, because hardware manual has typo.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
EHCI driver enables by default in kirkwood.dtsi.
This removes kirkwood_ehci_init function.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
OpenBlocks A6 uses second I2C with RTC of s35390a.
This supports them.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Second I2C bus is supported by 88f6282 and 88f6283.
This creates kirkwood-6282.dtsi, and defines DT table
of second I2C bus.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell 98DX412x SoC embed a kirkwood variant that does not have
pinctrl support yet. Even though this kirkwood is very similar to the
88f6281, on the MPP front a lot of pins are not available. That's why a
new kirkwood pinctrl variant is needed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Make use of the pinctrl driver for configuring all the pins, instead
of using the Orion mpp code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There are a couple of different variants of Kirkwood, which differ in
the pin muxing. These DTSI files set the correct compatibility and
define commonly used groups of pins, which board dbs files can
reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Tested-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
SolidRun CuBox has a led on a gpio pin. As there is now DT pinctrl
support for Dove, make use of a pinhog to ensure the pin is set to
gpio.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Following the ongoing conversion of Orion SoCs to DT, make use of
gpio and pinctrl drivers through DT. The main dtsi for Dove is prepared
to allow board specific descriptors to make use of pinctrl muxing.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB and HDD using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to USB using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Control the power to SATA0 and SATA1 using a fixed regulator.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A few boards use a GPIO line to enable power to subsystems, eg USB or
SATA devices. Pull in the regulator framework as the first step to
controlling these GPIO lines are regulators.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Also enable the gpio-poweroff driver when DT is used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The default chip-delay of 25us is a bit too tight for some DNS-320's,
and D-Link seem to specify 30us in their kernels for both devices.
Increase to 35us to make sure the NAND is stable.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the EHCI driver has DT support, drop old style configuration
of it and add DT in its place. Since all the boards enable the EHCI,
enable it by default in kirkwood.dtsi. Any new boards which don't have
USB can specifically disable it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
I missed one pull request from Samsung with one fix in the previous
batch. Here it is -- a dma driver fix for an early version of silicon
that they still support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bSmr
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull one more ARM SoC fix from Olof Johansson:
"I missed one pull request from Samsung with one fix in the previous
batch. Here it is -- a dma driver fix for an early version of silicon
that they still support."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
Pulling in a newer version of the depend branch from the gpio tree,
since there was some randconfig breakage introduced at the version we
had, and we want to keep those things as bisectable as possible. It's
not bad enough to warrant a rebase though, so there'll be a window of
exposure to this.
* depends/gpio-devel:
gpio: SPEAr: add spi chipselect control driver
gpio: gpio-max710x: Support device tree probing
gpio: twl4030: Use only TWL4030_MODULE_LED for LED configuration
gpio: tegra: read output value when gpio is set in direction_out
gpio: pca953x: Add compatible strings to gpio-pca953x driver
gpio: pca953x: Register an IRQ domain
gpio: mvebu: Set free callback for gpio_chip
gpio: tegra: Drop exporting static functions
gpio: tegra: Staticize non-exported symbols
gpio: tegra: fix suspend/resume apis
gpio-pch: Set parent dev for gpio chip
gpio: em: Fix build errors
Signed-off-by: Olof Johansson <olof@lixom.net>
Modern GCC can generate code which makes use of the CPU's native
unaligned memory access capabilities. This is useful for the C
decompressor implementations used for unpacking compressed kernels.
This patch disables alignment faults and enables the v6 unaligned
access model on CPUs which support these features (i.e., v6 and
later), allowing full unaligned access support for C code in the
decompressor.
The decompressor C code must not be built to assume that unaligned
access works if support for v5 or older platforms is included in
the kernel.
For correct code generation, C decompressor code must always use
the get_unaligned and put_unaligned accessors when dealing with
unaligned pointers, regardless of this patch.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a kernel is configured with a DT containing more /cpu nodes than
nr_cpu_ids, the number of cpus must be capped in the DT parsing
code. Current code carries out the check, but fails to cap the
value and the check is executed after the cpu logical index is used,
which can lead to memory corruption due to index overflow.
This patch refactors the check against nr_cpu_ids and move it before
any computed index is used in the parsing code.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit e50c541 (ARM: perf: add guest vs host discrimination) broken the
link as perf_instruction_pointer and perf_misc_flags are not defined
when CONFIG_HW_PERF_EVENTS is not selected.
As it make little sense to try and profile a guest without any HW event,
just fallback to the original code when this config option is not selected.
Reported-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull input updates from Dmitry Torokhov:
"This fixes recent regression where /dev/input/mice got assigned wrong
device node which messed up setups with static /dev, and a regression
in ads7846 GPIO debounce setup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
ARM - OMAP: ads7846: fix pendown debounce setting
Input: ads7846 - enable pendown GPIO debounce time setting
Input: mousedev - move /dev/input/mice to the correct minor
Input: MT - document new 'flags' argument of input_mt_init_slots()
From Kukjin Kim:
Here is Samsung fixes for v3.7 and it is for fixing of mdma1 address
for exynos4210 rev0 SoC.
* 'v3.7-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: PL330 MDMA1 fix for revision 0 of Exynos4210 SOC
Signed-off-by: Olof Johansson <olof@lixom.net>
The armada_cfg_base() function returns the base address of the
registers that allow to configure the decoding for a particular
address window. On Armada 370/XP, the lower windows have more
configuration registers (4 registers) than the higher windows (2
registers). This armada_cfg_base() takes this into account by doing a
different offset calculation depending on the window number, but this
offset calculation was wrong for the higher windows.
Even though we were not using high window numbers until now (only
window 0 is used to map the BootROM, needed for SMP), we use this
function at boot time to disable all windows to ensure that nothing
remains intialized from what the bootloader has done.
Unfortunately, the U-Boot on the OpenBlocks AX3-4 uses a window with a
high number (above 8) to remap the BootROM. And then when the kernel
boots, it remaps the BootROM in window 0. Normally, this is not a
problem, because all windows have previously been disabled. Except
that due to our wrong offset calculation, the windows with high
numbers were not properly disabled, leading to the BootROM being
mapped twice. The visible result of this bug was that the kernel was
unable to get the second CPU started on the OpenBlocks AX3-4
platform. With this fix, all windows are properly cleared at boot
time, the BootROM is remapped only once in window 0, and the second
CPU boots fine.
Thanks a lot to Lior Amsamlen <alior@marvell.com> for his help in
debugging this problem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
Strictly speaking, this bug was introduced in 3.7, but since the only
platforms supported in 3.7 were Armada 370 and Armada XP, and there
was anyway no SMP support at this time, it isn't really worth the
effort to push this patch in 3.7.
Now that the additional enable bits in the enet PLL are handled
as gates, the gate_mask is identical for all plls. Remove the
gate_mask from the code and use the BM_PLL_ENABLE bit for
enabling/disabling the PLL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
In current code the ethernet PLL is not handled correctly. The PLL runs at 500MHz
and has different outputs. Only the enet reference clock is implemented. This
patch changes the PLL so that it outputs 500MHz and adds the additional outputs
as dividers. This now matches the datasheet which says:
> This PLL synthesizes a low jitter clock from 24 MHz reference clock.
> The PLL outputs a 500 MHz clock. The reference clocks generated by this PLL are:
> • Ref_PCIe = 125 MHz
> • Ref_SATA = 100 MHz
> • Ref_ethernet, which is configurable based on the PLL_ENET[1:0] register field.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
In recent reference manuals the PLLs were renumbered. PLL8 now is
PLL6 and vice versa. Change the code according to the reference
manual to avoid confusion.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCs+5oACgkQCwYYjhRyO9UywACfVp3WPDHLxE8ypew3AWoTyxe3
JcMAoIjojnjWCd44cqDJ4uEpvi6KNquE
=BR8m
-----END PGP SIGNATURE-----
Merge tag 'marvell-armadaxp-smp-for-3.8' of github.com:MISL-EBU-System-SW/mainline-public into mevbu-dt-additions
SMP support for Armada XP
The purpose of this series is to add the SMP support for the Armada XP
SoCs. Beside the SMP support itself brought by the last 3 commits,
this series also adds the support for the coherency fabric unit and
the power management service unit.
The coherency fabric is responsible for ensuring hardware coherency
between all CPUs and between CPUs and I/O masters. This unit is also
available for Armada 370 and will be used in an incoming patch set
for hardware I/O cache coherency.
The power management service unit is responsible for powering down and
waking up CPUs and other SOC units.
Conflicts:
arch/arm/mach-mvebu/armada-370-xp.c
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for Plat'Home OpenBlocks A6 using the device tree
where possible.
This commit supports SATA, USB, ether and serial console.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds initial dts file for EXYNOS5440 SoC and adds the
dts file for SSDK5440 board which is a kind of reference board.
More properties will be added later.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The ixp4xx queue manager uses "const struct qmgr_regs __iomem *" as the
type for a pointer that is passed to __raw_writel, which is not
allowed because of the const-ness.
Dropping the 'const' keyword fixes the problem. While we're here,
let's also drop the useless type cast.
Without this patch, building ixp4xx_defconfig results in:
In file included from arch/arm/mach-ixp4xx/ixp4xx_qmgr.c:15:0:
arch/arm/mach-ixp4xx/include/mach/qmgr.h: In function 'qmgr_put_entry':
arch/arm/mach-ixp4xx/include/mach/qmgr.h:96:2: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
In file included from drivers/net/ethernet/xscale/ixp4xx_eth.c:41:0:
arch/arm/mach-ixp4xx/include/mach/qmgr.h: In function 'qmgr_put_entry':
arch/arm/mach-ixp4xx/include/mach/qmgr.h:96:2: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
arch/arm/mach-ixp4xx/ixp4xx_qmgr.c: In function 'qmgr_set_irq':
arch/arm/mach-ixp4xx/ixp4xx_qmgr.c:41:9: warning: passing argument 2 of '__raw_writel' discards 'const' qualifier from pointer target type [enabled by default]
arch/arm/include/asm/io.h:88:91: note: expected 'volatile void *' but argument is of type 'const u32 *'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
It doesn't make much sense to map QMgr dynamically - we almost always need it
and the static mapping will be needed for little-endian data-coherent operation
(to make QMgr region value-coherent).
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlCtU90ACgkQ9lPLMJjT96dSdQCfcmuU/3oXziktW6coEOwWD0rZ
rpAAoITtWPO7RNRqhCVQGFJKuuy5sid7
=ME0a
-----END PGP SIGNATURE-----
Merge tag 'marvell-openblocks-i2c-sata-for-3.8' of git://github.com/MISL-EBU-System-SW/mainline-public into mvebu/everything
Marvell SATA and I2C enabling for OpenBlocks AX3-4
When booting with DT the OF core can fill up the resources provided within
the DT blob.
The current way of handling the DT boot prevents us from removing hwmod data
for platforms only suppose to boot with DT (OMAP5 for example) since we need
to keep the whole hwmod database intact in order to have more resources in
hwmod than in DT (to be able to append the DMA resource from hwmod).
To fix this issue we just examine the OF provided resources:
If we do not have resources we use hwmod to fill them.
If we have resources we check if we already able to recive DMA resource, if
no we only append the DMA resurce from hwmod to the OF provided ones.
In this way we can start removing hwmod data for devices which have their
resources correctly configured in DT without regressions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: fixed checkpatch problem; updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add flags parameter for omap_hwmod_count_resources() so users can tell which
type of resources they are interested when counting them in hwmod database.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 has module specific context lost registers which makes it now
possible to have module level context loss count, instead of relying
on the powerdomain level context count.
Add 2 private hwmod api's to update/clear the hwmod/module specific
context lost counters/register.
Update the module specific context_lost_counter and clear the hardware
bits just after enabling the module.
omap_hwmod_get_context_loss_count() now returns the hwmod context loss
count them on platforms where they exist (OMAP4), else fall back on
the pwrdm level counters for older platforms.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: added function kerneldoc, fixed structure kerneldoc,
rearranged structure to avoid memory waste, marked fns as OMAP4-specific,
prevent fn entry on non-OMAP4 chips, reduced indentation, merged update
and clear, merged patches]
[t-kristo@ti.com: added support for arch specific hwmod ops, and changed
the no context offset indicator to USHRT_MAX]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: use NO_CONTEXT_LOSS_BIT flag rather than USHRT_MAX;
convert unsigned context lost counter to int to match the return type;
get rid of hwmod_ops in favor of the existing soc_ops mechanism;
move context loss low-level accesses to the PRM code]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some PRM functions will need to be called by the hwmod code early in
kernel init. To handle this, split the PRM initialization code into
early and late phases. The early init is handled via mach-omap2/io.c,
while the late init is handled by subsys_initcall().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Now that we have support for the I2C busses on Armada 370/XP, and
support for the RTC on the OpenBlocks AX3-4 platform, include the
necessary options in mvebu_defconfig.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch enables SATA support on the OpenBlocks AX3-4. It has one
internal SATA port, and an external eSATA port.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The OpenBlocks AX3-4 has a Seiko Instruments S-35390A as the RTC
controller. This patch enables this RTC device in the OpenBlocks
AX3-4 Device Tree.
[Thomas Petazzoni: updated with other OpenBlocks changes, rephrased
commit log.]
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The OpenBlocks AX3-4 board, based on the Armada XP SoC, has an I2C
bus. This patch enables this bus and sets the clock frequency of the
bus.
[Thomas Petazzoni: updated with other changes on OpenBlocks, rephrased
commit log.]
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Armada 370 and Armada XP have the same I2C controllers as previous
Marvell SoCs, so the existing mv64xxx-i2c driver works fine.
[Thomas Petazzoni: updated on top of other Armada 370/XP changes,
rephrased the commit log].
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
essential pins.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pJyU
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Few more regression fixes related to u-boot only muxing
essential pins.
* tag 'omap-for-v3.7-rc5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4: TWL: mux sys_drm_msecure as output for PMIC
ARM: OMAP3: igep0020: Set WIFI/BT GPIO pins in correct mux mode
ARM: OMAP: Add maintainer entry for IGEP machines
It has been a while since dove_defconfig was updated to recent development.
This patch adds all currently available Dove boards, including a DT-enabled
machine.
DT support requires to allow ATAGS passed by boot loader as most of them are
not yet capable of passing DT blobs. Also OF_SERIAL is enabled to actually
see the bootlog.
Finally, sdhci driver for Dove, mv_cesa, GPIO LEDs, and highmem support is
added.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Commit 97ee9f01 (ARM: OMAP: fix the ads7846 init code) have enabled the
pendown GPIO debounce time setting by the below sequence:
gpio_request_one()
gpio_set_debounce()
gpio_free()
It also revealed a bug in the OMAP GPIO handling code which prevented
the GPIO debounce clock to be disabled and CORE transition to low power
states.
Commit c9c55d9 (gpio/omap: fix off-mode bug: clear debounce settings on
free/reset) fixes the OMAP GPIO handling code by making sure that the
GPIO debounce clock gets disabled if no GPIO is requested from current
bank.
While fixing the OMAP GPIO handling code (in the right way), the above
commit makes the gpio_request->set_debounce->free sequence invalid as
after freeing the GPIO, the debounce settings are lost.
Fix the debounce settings by moving the debounce initialization to the
actual GPIO requesting code - the ads7846 driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit converts the 'LaCie Ethernet Disk mini v2' board to the
Device Tree. All devices that have existing Device Tree bindings are
converted over to the Device Tree, the other devices remain
instantiated in the old way, until the respective drivers get the
needed Device Tree bindings.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds basic DT support for the Orion5x SoC family. It adds
an orion5x.dtsi description of the Orion5x SoC as well as the needed
DT_MACHINE structure to support boards converted to DT in the future.
So far, the Device Tree contains the interrupt controller, the GPIO
bank, the UART controllers, the SPI controller, the watchdog, the SATA
controller, the I2C controller and the cryptographic engine.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit is a simple mechanical update of the orion5x_defconfig
file to the current kernel (i.e, just 'make orion5x_defconfig; make
savedefconfig'). Doing this update allows to more easily separate
DT-related configuration changes in the following patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
