v2: Introduce some nice #defines for the FDI lane width fields and put
them to good use. Suggested by Ville.
v3: Fixup the mask vs. shift copy&pasta fail Imre Deak spotted, and
use the shift #define also in the mask.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this for two reasons:
- Correct handling of shared fdi lanes on ivb with fastboot.
- Handling fdi link bw limits when we only have two fdi lanes by
dithering down a bit.
Just search&replace in this patch, no functional change at all.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code is rather ... ugly. The only thing it managed to pull
off is getting 6bpc on DP working on g4x. Then someone added another
custom hack for 6bpc eDP on vlv. Fix up this entire mess by properly
implementing the PIPECONF-based dither/bpc controls on g4x/vlv.
Note that compared to pch based platforms g4x/vlv don't support 12bpc
modes. g4x is already caught, extend the check for vlv.
The other fixup is to restrict the lvds-specific dithering to early
gen4 devices - g4x should use the pipeconf dither controls. Note that
on gen2/3 the dither control is in the panel fitter even.
v2: Don't enable dithering when the pipe is in 10 bpc mode. Quoting
from Bspec "PIPEACONF - Pipe A Configuration Register, bit 4":
"Programming note: Dithering should only be enabled for 8 bpc or 6
bpc."
v3: Actually drop the old ugly dither code.
v4: Explain in a short comment why g4x/vlv shouldn't dither for 30 bpp
pipes (Jesse).
v5: Also clear the dither type correctly as spotted by Ville.
v6: As Ville pointed out we need to indeed set the dithering both in
the pipeconf register (for DP outputs) and in the LVDS port register
(for LVDS ouputs). Otherwise LVDS panel will not get properly
dithered. The old patch got away with this since it forgot to clear
the LVDS dither bit ...
v7: Remove redundant BPC_MASK clearing, spotted by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They can get at the adjusted mode through intel_crtc->config.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This hack is getting a bit messy, but this plugs the leak for now
until we have the cpu_transcoder properly pipe_config'ed.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And put the pfit stuff into substructs while we're at it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This gets the panel fitter working on eDP on VLV, and should also apply
to eDP panels on G4x chipsets (if we ever detect and mark an all-in-one
panel as eDP anyway).
A few cleanups are still possible on top of this, for example the LVDS
border control could be placed in the LVDS encoder structure and updated
based on the result of the panel fitter calculation.
Multi-pipe fitting isn't handled correctly either if we ever get a config
that wants to try the panel fitter on more than one output at a time.
v2: use pipe_config for storing pfit values (Daniel)
add i9xx_pfit_enable function for use by 9xx and VLV (Daniel)
v3: fixup conflicts and lvds_dither check
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: fix up botched conflict resolution from Jesse:
- border = LVDS_BORDER_ENABLE was lost for CENTER scaling
- comment about gen2/3 panel fitter scaling was lost
- dev_priv->lvds_dither reintroduced.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only ever check whether it's strictly bigger than one, so all the
is_sdvo/is_hdmi checks are redundant. Flatten the code a bit.
Also, s/temp/dpll_md/
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we compute the pch pll state, we _have_ a pch encoder.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
g4x dplls and ilk+ pch plls have a separate field for the reduced p1
setting, so this restriction does not apply. Only older platforms have
the restriction that the p1 divisors must match.
This unnecessary restriction has been introduced in
commit cec2f356d5
Author: Sean Paul <seanpaul@chromium.org>
Date: Tue Jan 10 15:09:36 2012 -0800
drm/i915: Only look for matching clocks for LVDS downcloc
Note that with lvds the p2 divisors _always_ match for LVDS, and we
don't support auto-downclocking anywhere else. On eDP downclocking
works with separate data m/n settings, using the same link clock.
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up to now we've relied on the bios to get this right for us. Let's try
out whether our code has improved a bit, since we should dither
always when the output bpp doesn't match the plane bpp.
- gen5+ should be fine, since we only use the bios hint as an upgrade.
- gen4 changes, since here dithering is still controlled in the lvds
register.
- gen2/3 has implicit dithering depeding upon whether you use 2 or 3
lvds pairs (which makes sense, since it only supports 8bpc pipe
outpu configurations).
- hsw doesn't support lvds.
v2: Remove redudant dither setting.
v3: Completly drop reliance on dev_priv->lvds_dither.
v4: Enable dithering on gen2/3 only when we have a 18bpp panel, since
up-dithering to a 24bpp panel is not supported by the hw. Spotted by
Ville.
v5: Also only enable lvds port dithering on gen4 for 18bpp modes. In
practice this only excludes dithering a 10bpc plane down for a 24bpp
lvds panel. Not something we truly care about. Again noticed by Ville.
v6: Actually git add.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the exception of hsw, which has dedicated DP clocks which run at
the fixed frequency already, and vlv, which doesn't have optmized
pre-defined dp clock parameters (yet).
v2: Ville asked me to elaborate a bit more on the longer-term goals
wrt dpll settings computation:
So ultimately my idea is that in the compute config stage first the crtc
code puts the default platform pll limits into the pipe_config. Then
encoders can either overwrite that limit structure with their own special
stuff (mostly for lvds madness). Or they can pick some or all of the
parameters (e.g. just the p2 switchover on hdmi, or all the clock
parameters for dp/sdvo tv).
Once that's done then the generic crtc code can fill out any missing bits
(using the find_best_pll code) and then try to assign which pll to use (if
it's a platform with shared plls). In the end the modeset could should
simply write the computed stuff into registers and never be able to fail.
Of course there's still a lot of data to be moved into pipe_config to make
this all happen, hence some of the temporary ugliness.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was somehow lost in the pipe_config->dpll introduction in
commit f47709a950
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 28 10:42:02 2013 +0100
drm/i915: create pipe_config->dpll for clock state
While at it, extract a few small helpers for common computations.
v2: Use the newly added helpers more thanks to Ville's trick to
typedef the legacy intel_clock_t as the new-world struct dpll.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need the dpll/fp/fp2 values only when we need a pch pll. So move
them together with the code to acquire such a pll.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevents black screens when using 30bpp framebuffers on my
HDMI screens here. The DP input on the same screen though reports a
1.4 EDID with the correct 8bpc limit set.
v2: Actually check for the right thing!
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our rps code relies on the interrupts being off to prevent re-arming
of the work items at inopportune moments.
Also drop the redundant cancel_work for the main rps work,
disable_gt_powersave already takes care of that.
Finally add a WARN_ON to ensure we obey that piece of ordering
constraint. Long term I want to lock down the setup/teardown code in a
similar way to how we painstakingly check modeset sequence constraints
already.
v2: Disable polling after hpd handling is shut down - since Egbert's
hpd irq storm handling the hotplug work can re-arm the polling
handler. Spotted by Jani Nikula.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows unifying a bunch of the PLL calculations and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... inside haswell_get_pipe_config. Because there's one TRANS_DDI_FUNC_CTL
register per CPU transcoder, not per pipe. This solves "unclaimed register"
messages when booting with eDP only and using the i915.disable_power_well=1.
Also fix a comment and remove an useless empty line.
The error messages were caused by:
commit 88adfff1ad
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 28 10:42:01 2013 +0100
drm/i915: hw readout support for ->has_pch_encoders
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes "unclaimed register" messages when booting with eDP only
and i915.disable_power_well=1.
The error messages were caused by:
commit 0e8ffe1bf8
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 28 10:42:00 2013 +0100
drm/i915: add hw state readout/checking for pipe_config
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this commit we enable both CPU and PCH FIFO underrun reporting and
start reporting them. We follow a few rules:
- after we receive one of these errors, we mask the interrupt, so
we won't get an "interrupt storm" and we also won't flood dmesg;
- at each mode set we enable the interrupts again, so we'll see each
message at most once per mode set;
- in the specific places where we need to ignore the errors, we
completely mask the interrupts.
The downside of this patch is that since we're completely disabling
(masking) the interrupts instead of just not printing error messages,
we will mask more than just what we want on IVB/HSW CPU interrupts
(due to GEN7_ERR_INT) and on CPT/PPT/LPT PCHs (due to SERR_INT). So
when we decide to mask PCH FIFO underruns for pipe A on CPT, we'll
also be masking PCH FIFO underruns for pipe B, because both are
reported by SERR_INT, which has to be either completely enabled or
completely disabled (in othe words, there's no way to disable/enable
specific bits of GEN7_ERR_INT and SERR_INT).
V2: Rename some functions and variables, downgrade messages to
DRM_DEBUG_DRIVER and rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Valleyview voltage swing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric. Update
vlv_update_pll, i9xx_crtc_enable, and intel_enable_pll with the
appropriate programming.
We need to make sure that the tx lane reset occurs in both the full mode
set and DPMS paths, so factor things out to allow that.
v2: use different DPIO_DIVISOR values for VGA and DisplayPort
v3: Fix update pll logic to use same DPIO_DIVISOR & DPIO_REFSFR values
for all display interfaces
v4: collapse with various updates
v5: squash with crtc enable/pll enable bits
v6: split out DP code (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
remove unneeded check in 9xx pll div update (Jani)
wrap VLV pll update call in IS_VALLEYVIEW (Jani)
move port enable back to end of crtc enable (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
v7: fix up conflicts against latest drm-intel-next-queued
v8: use DPIO reg names, fix pipes (Jani)
from mPhy_registers_VLV2_ww20p5 doc
v9: update to latest info from driver enabling notes doc
driver_vbios_notes_9
v10: fixup a bit of pipe/port confusion to allow eDP and HDMI to work
simultaneously (Jesse)
v11: use pll/port callbacks for DPIO port activity (Daniel)
use separate VLV CRTC enable function (Daniel)
move around port ready checks (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop pfit changes and add a little comment explaining that
vlv has a different enable sequence and so needs it's own crtc_enable
callback. Also apply a fixup patch from Wu Fengguang to shut up some
compiler warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a reset feature we don't actually need.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Make it compile.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Program few Tx buffer Swing control settings through DPIO.
v2: fix up codingstyle (Daniel)
call from set_signal_levels (Ville, Daniel)
use proper port numbers (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Yogesh M <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2 changes)
[danvet: Reorder if-ladder to avoid two IS_VLV checks.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Magic updates.
v2: use 64 bit types and math (Ville)
v3: Trim out all the m/n/p calculation changes since they are still
under discussion. Instead squash in a fixup for hdmi limits which
slipped into a different patch.
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Yogesh M <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add sprite_name() macro which should be used with the kind of sprites
that are fixed to pipes (gen4.5+).
Also use dev_priv->num_plane to calculate the sprite index insted
assuming two sprites per pipe. This should make it print the right
name.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Print the alphabetical name for transcoders. The code already used the
pipe_name() macro for transcoders, so I did the same. But we do have the
(unused) transcoder_name() macro which could be used instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alway use the alphabetical names in debug/error messages for planes,
pipes and ports, instead of using decimal numbers occasionally.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of the few remaining open coded copies of
pipe_name() and port_name().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When adding the pipe config computation step I've accidentally moved
this a bit away. Which momentarily confused me since the pipe config
step rejected some modesetting operations I expected and so left me
looking in vain for that debug output.
v2: Move the debug output into the right function to prevent this from
happening again.
v3: Make it compile (Ville). Also reorder the patch so that the two
bugfixes are first.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i9xx modeset sequence is currently pretty fishy, so tight it all
up with some good assert-sprinkling.
We already have good coverage on the disable side, but the enable side
is spotty (since until recently it was wrong).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just blows through 50ms for naught, since the pipe is off.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is horrible lore and we should be able to get rid of it now
that the lvds/pfit handling code actually does the right thing.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Oops.
This regression has been introduced in
commit 5d2d38ddca
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:45:01 2013 +0100
drm/i915: clean up pipe bpp confusion
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reason we need to more accurately track this:
- hw pipe state readout for Haswell needs the cpu transcoder.
- We need to know the right cpu transcoder in a bunch of places in
->disable and other modeset callbacks.
In the future we need to add hw state readout&check support, too. But
to avoid ugly merge conflicts do the rote sed job now without any
functional changes.
v2: Preserve the cpu_transcoder value when overwriting crtc->config.
Reported by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: Removed rough whitespace that Chris spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may have DDI_BUF_CTL(PORT_A) configured with 2 lanes and still not
have CRT, so just check for !IS_ULT. This problem happened on a real
machine and resulted in a very ugly dmesg.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The recent rework of the pfit handling didn't take into account that
the panel fitter is fixed to pipe B:
commit 24a1f16de9
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Fri Feb 8 16:35:37 2013 +0200
drm/i915: disable shared panel fitter for pipe
Fix this up by properly computing the pipe the pfit is on. Also
extract the logic into its own function, add a debug assert to check
that the pipe is off (mostly just documentation) and add some debug
output.
If pipe A was disabled after pipe B was set up, the panel fitter will
be disabled. Now most userspace doesn't do modesets in this order,
which is why I couldn't ever reproduce this and why it took me so long
to figure out.
We really need hw state readout and check support for the pannel
fitter ...
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
References: http://permalink.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/19049
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yet again our current confusion between doing the modeset globally,
but only having the new parameters for one crtc at a time.
So that intel_set_mode essentially already does a global modeset:
intel_modeset_affected_pipes compares the current state with where we
want to go to (which is carefully set up by intel_crtc_set_config) and
then goes through the modeset sequence for any crtc which needs
updating.
Now the issue is that the actual interface with the remaining code
still only works on one crtc, and so we only pass in one fb and one
mode. In intel_set_mode we also only compute one intel_crtc_config
(which should be the one for the crtc we're doing a modeset on).
The reason for that mismatch is twofold:
- We want to eventually do all modeset as global state changes, so
it's just infrastructure prep.
- But even the old semantics can change more than one crtc when you
e.g. move a connector from crtc A to crtc B, then both crtc A and B
need to be updated. Usually that means one pipe is disabled and the
other enabled. This is also the reason why the hack doesn't touch the
disable_pipes mask.
Now hilarity ensued in our kms config restore paths when we actually
try to do a modeset on all crtcs: If the first crtc should be off and
the second should be on, then the call on the first crtc will notice
that the 2nd one should be switched on and so tries to compute the
pipe_config. But due to a lack of passed-in fb (crtc 1 should be off
after all) it only results in tears.
This case is ridiculously easy to hit on gen2/3 where the lvds output
is restricted to pipe B. Note that before the pipe_config bpp rework
gen2/3 didn't care really about the fb->depth, so this is a regression
brought to light with
commit 4e53c2e010
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:44:58 2013 +0100
drm/i915: precompute pipe bpp before touching the hw
But apparently Ajax also managed to blow up pch platforms, probably
with some randomized configs, and pch platforms trip up over the lack
of an fb even in the old code. So this actually goes back to the first
introduction of the new modeset restore code in
commit 45e2b5f640
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 23 18:16:34 2012 +0100
drm/i915: force restore on lid open
Fix this mess by now by justing shunting all the cool new global
modeset logic in intel_modeset_affected_pipes.
v2: Improve commit message and clean up all the comments in
intel_modeset_affected_pipes - since the introduction of the modeset
restore code they've been a bit outdated.
Bugzill: https://bugzilla.redhat.com/show_bug.cgi?id=917725
Cc: stable@vger.kernel.org
References: http://www.mail-archive.com/stable@vger.kernel.org/msg38084.html
Tested-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backlight cleanup in the eDP connector destroy callback caused the
backlight device to be removed on some systems that first initialized LVDS
and then attempted to initialize eDP. Prevent multiple backlight
initializations, and ensure backlight cleanup is only done once by moving
it to modeset cleanup.
A small wrinkle is the introduced asymmetry in backlight
setup/cleanup. This could be solved by adding refcounting, but it seems
overkill considering that there should only ever be one backlight device.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55701
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Peter Verthez <peter.verthez@skynet.be>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This solves some "unclaimed register" messages when booting the
machine with eDP attached.
V2: Rebase and add the comment requested by Daniel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It returns true if we've requested to turn the power well on and it's
really on. It also returns true for all the previous gens.
For now there's just one caller, but I'm going to add more.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will be only consistent once we've restored all the crtcs. Since a
bunch of other callers also want to just restore a single crtc, add a
boolean to disable checking only where it doesn't make sense.
Note that intel_modeset_setup_hw_state already has a call to
intel_modeset_check_state at the end, so we don't reduce the amount of
checking.
v2: Try harder not to create a big patch (Chris).
v3: Even smaller (still Chris). Also fix a trailing space.
References: https://lkml.org/lkml/2013/3/16/60
Cc: Tomas Melin <tomas.melin@iki.fi>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Tomas Melin <tomas.melin@iki.fi>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec has been been updated and dropped these two changes for non-sdv
LPT PCHs.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace can easily hit this and does since Ville added a new evil
igt testcase in:
commit 069e35e0fc3785faa562adcfd2dd7bbed4cb1dea
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Mar 4 15:34:06 2013 +0200
kms_flip: Add flip-vs-bad-tiling test
v2: Fix the spelling in the added comment (Chris).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=63246
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the ratio is different, we also need to pass in the parameters
for the reduced clock. Might or might not reduce flicker for the
auto-downclocking on lvds/eDP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only on IBX should we set the limiting factor to 25 unconditionally
for dual-channel mode, on CPT/PPT 25 only applies when the lvds
refclock is 100MHz.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit de13a2e3f8
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Sep 20 18:36:05 2012 -0300
drm/i915: extract compute_dpll from ironlake_crtc_mode_set
missed the subtle adjustment of the FP1 register. Fix this up by
passing a pointer around instead of the value.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN supports a fusing option which subtracts the PCH display (making the
CPU display also useless). In this configuration MMIO which gets decoded
to a certain range will hang the CPU.
For us, this is sort of the equivalent of having no pipes, and we can
easily modify some code to not do certain things with no pipes.
v2: Moved the num pipes check up in the call chain, and removed extra
checks noted by Daniel. For more details, see:
http://lists.freedesktop.org/archives/intel-gfx/2013-March/025746.html
v3: Drop the intel_setup_overlay check (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV has the color range selection bit in the PIPECONF register.
Configure it appropriately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
[danvet: fixup rebase issues due to slightly different baseline.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clock computations and handling are highly encoder specific, both in
the optimal clock selection and also in which clocks to use and when
sharing of clocks is possible.
So the best place to do this is somewhere in the encoders, with a
generic fallback for those encoders without special needs. To facility
this, add a pipe_config->clocks_set boolean.
This patch here is only prep work, it simply sets the computed clock
values in pipe_config->dpll, and uses that data in the hw clock
setting functions.
Haswell code isn't touched, simply because Haswell clocks work much
different and need their own infrastructure (with probably a
Haswell-specific config->ddi_clock substruct).
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
