This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.
Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Due to a HW issue, our current scheme to transition the connection from
streaming to rdma mode is broken on the passive side. The firmware
and driver now support a new transition scheme for the passive side:
- driver posts rdma_init_wr (now including the initial receive seqno)
- driver posts last streaming message via TX_DATA message (MPA start
response)
- uP atomically sends the last streaming message and transitions the
tcb to rdma mode.
- driver waits for wr_ack indicating the last streaming message was ACKed.
NOTE: This change also bumps the required firmware version to 4.3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This was spotted by the Coverity checker (CID 1554).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cxgb3 uses dma_alloc_coherent() et al. thus needs linux/dma-mapping.h
include in order to build reliably.
Noticed on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- don't mark static functions in C files as inline - gcc should know
best whether inlining makes sense
- never compile the unused cxio_dbg.c
- make the following needlessly global functions static:
- cxio_hal.c: cxio_hal_clear_qp_ctx()
- iwch_provider.c: iwch_get_qp()
- remove the following unused global functions:
- cxio_hal.c: cxio_allocate_stag()
- cxio_resource.: cxio_hal_get_rhdl()
- cxio_resource.: cxio_hal_put_rhdl()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove the Open Grid Computing copyright. It shouldn't be there.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an RDMA/iWARP driver for the Chelsio T3 1GbE and 10GbE adapters.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
