Change default frequency to be US Broadcast channel 3 - with the
transition to d igital the previous value has now become useless.
This change is PURELY to help with my testing (I need to set some kind
of default so it might as well be some thing usable).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25840 module's VBI initialization logic uses the current video
standard as part of its internal algorithm. This therefore means that
we probably need to make sure that the correct video standard has been
set before initializing VBI. (Normally we would not care about VBI,
but as described in an earlier changeset, VBI must be initialized
correctly on the cx25840 in order for the chip's hardware scaler to
operate correctly.)
It's kind of messy to force the video standard to be set before
initializing VBI (mainly because we can't know what the app really
wants that early in the initialization process). So this patch does
the next best thing: VBI is re-initialized after any point where the
video standard has been set.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25840 module requires that its VBI initialization entry point be
called in order for hardware-scaled video capture to work properly -
even if we don't care about VBI. Making this behavior even more
subtle is that if the capture resolution is set to 720x480 - which is
the default that the pvrusb2 driver sets up - then the cx25840
bypasses the hardware scaler. Therefore this problem does not
manifest itself until some other resolution, e.g. 640x480, is tried.
MythTV typically defaults to 640x480 or 480x480, which means that
things break whenever the driver is used with MythTV.
This all has been known for a while (since at least Nov 2006), but
recent changes in the pvrusb2 driver (specifically in regards to
sub-device support) caused this to break again. VBI initialization
must happen *after* the chip's firmware is loaded, not before. With
this fix, 24xxx devices work correctly again.
A related fix that is part of this changeset is that now we
re-initialize VBI any time after we issue a reset to the cx25840
driver. Issuing a chip reset erases the state that the VBI setup
previously did. Until the HVR-1950 came along this subtlety went
unnoticed, because the pvrusb2 driver previously never issued such a
reset. But with the HVR-1950 we have to do that reset in order to
correctly transition from digital back to analog mode - and since the
HVR-1950 always starts in digital mode (required for the DVB side to
initialize correctly) then this device has never had a chance to work
correctly in analog mode! Analog capture on the HVR-1950 has been
broken this *ENTIRE* time. I had missed it until now because I've
usually been testing at the default 720x480 resolution which does not
require scaling... What fun. By re-initializing VBI after a cx25840
chip reset, correct behavior is restored.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure that we're programming the tda18271 tuner with the correct
IF frequencies to match the programming of the TDA10048 DVB-T demod
for the HVR1200 and HVR1700 products.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks for Terry Wu for pointing out the missing entry.
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The variable 'rc' could be used uninitialized in the cx231xx_capture_start
function. Sri informed me that it should be initialized to -1.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tcm825x_remove is not necessarily called on module exit, it can also be
called when the i2c_adapter is removed. While the i2c adapter might never
be removed on an embedded system, in practice this sensor driver can also
be used in e.g. a USB webcam where this is a perfectly acceptable thing
to do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rxsubchans was only set when stereo was detected, otherwise it was
left to 0 instead of setting it to mono.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it very clear that this header should not be used for i2c drivers that
do not need to be compiled for pre-2.6.26 kernels.
As soon as the minimum supported kernel in the v4l-dvb repository becomes
2.6.26 or up, then this header should be removed entirely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gcc 4.3.1 generates this warning:
v4l/smscoreapi.c: In function 'smscore_gpio_configure':
v4l/smscoreapi.c:1481: warning: 'GroupNum' may be used uninitialized in this function
v4l/smscoreapi.c:1480: warning: 'TranslatedPinNum' may be used uninitialized in this function
While in practice this will not happen, it is something that the compiler
can't determine. Initializing these two local variables to 0 suppresses
this warning.
Cc: Udi Atar <udi.linuxtv@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A previous change (v4l2-common: remove v4l2_ctrl_query_fill_std) broke
the handling of class controls in VIDIOC_QUERYCTRL. The MPEG class control
was broken for all drivers that use the cx2341x module and the USER class
control was broken for ivtv and cx18.
This change adds back proper class control support.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the EVGA inDtube. Both ATSC and analog side validated as
fully functional.
Thanks to Jake Crimmins from EVGA for providing the correct GPIO info.
Thanks to Alan Hagge for doing all the device testing.
Thanks to Greg Williamson for providing hardware for testing.
Cc: Jake Crimmins <jcrimmins@evga.com>
Cc: Alan Hagge <ahagge@gmail.com>
Cc: Greg Williamson <cheeseboy16@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cases where the board had a default USB ID, we would not indentify the
board until after the call to em28xx_set_mode(). As a result, for those
boards the analog GPIOs were not being set before probing the i2c bus for
devices (the probe would occur with the GPIOs being all high).
Make a call to em28xx_set_mode() so that the GPIOs are set properly before
probing the i2c bus for devices.
This problem was detected with the EVGA inDtube, where the tvp5150 is not
powered on unless GPIO1 is pulled low.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Name saturation control saturation, not color and make the default
less saturated (the old default was overdoing it).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise
the picture is upside down. It is better to instead invert the meaning
of the control in the set function, and have the default be no vflip,
as one would expect vflip enabled to be upside down.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: enable autogain control for the ov7620, and not only
make it enable autogain but also auto exposure (and do the
same for the ov7648).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer
overflows during my testing of a "Premier" 0c45:613e cam
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark the v4l1 uvcvideo quickcam messenger driver as deprecated, the one
cam it supports, is now also supported by the v4l2 gspca stv06xx driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: enable support for 0c45:613e camera, and slightly tweak
the ov7630 register init values for a much better picture.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control index defines for the gspca_sonixj driver were numbered
wrong, causing us to disable the wrong controls on various sensors
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark the v4l1 ov511 as deprecated as we now have ov511 support in
the gspca ov519 driver. Note we should really also keep track of this
in Documentation/feature-removal-schedule.txt, but that is not
part of the v4l-dvb tree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ov511: remove ov518 usb id's from the driver, as they have not been working
ever since the decompression code got removed from the kernel, and they
are no supported by the gspca_ov519 module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for st6422 bridge and sensor to the stv06xx gspca sub driver,
tested with:
Logitech QuickCam Messenger 046d:08f0 ST6422 integrated
Logitech QuickCam Mess. Plus 046d:08f6 ST6422 integrated
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: Cleanup some sensor special cases
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: add support for the ov511 bridge
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hmm, another one with an extra if (life sucks) the
default contrast really is no good for the ov6630, it
isn't even high enough in full daylight, this gives
the ov6630 a different initial value for a better out
of the box experience.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported on the ov51x-jpeg list, and as I can confirm with my own cam
the ov7670 in 320x240 has a number of broken columns of pixels
at the left of the picture. This was not present in the old
driver as it always used 640x480 and did software
downscaling (took me a while to figure that one out).
The fix adds a sensor specific if in so far sensor
neutral code :( But this is the only way to fix this,
this cannot be fixed by only changing sensor registers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My ov519 cam has it led inverted, the same has been
reported on the ov51x-jpeg list for another
creative cam. This patch fixes this without changing
the behaviour for other cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: Add 320x240 and 160x120 support for cif sensor cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fix for the UV swapping in qcif mode with the ov6630, which I did
to fix this issue on a ov518 cam with an ov66308AF, causes UV swapping in
qcif with another cam of mine with the ov518 and an ov66308AE, so this
patch changes the code to differentiate between the ov66308AF and other
ov6630 versions, and restricts the UV swap fix to the ov66308AF.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds autobrightness (so that it can
be turned off to make the already present brightness
control work) and light frequency filtering controls.
The lightfreq control needed 2 different entries
in the ctrls array, as the number of options differs
depending on the sensor. Always one of the 2 entires is
disabled ofcourse.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix Leadtek TV2000 XP Global entries and add missing PCI ID's.
Thanks to Terry Wu <terrywu2009@gmail.com> for pointing us for the proper settings.
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 5d23a1d2 ("net: replace dma_sync_single with
dma_sync_single_for_cpu") replaced uses of the deprectated function
dma_sync_single() with calls to dma_sync_single_for_cpu(). However,
to be correct, the code should do a sync for_cpu() before touching the
memory and for_device() after it's done.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dma_sync_single() is deprecated now, and the use in mthca is wrong:
there should be a dma_sync_single_for_cpu() before touching the memory
from the CPU, and a dma_sync_single_for_device() afterwards. Fix
this, prompted by a kick in the pants from a patch from FUJITA
Tomonori <fujita.tomonori@lab.ntt.co.jp>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Before issuing reset, libata configures xfermode to PIO0 which makes
some drivers turn on IORDY which may cause the controller to lock up
if the port is not occupied. IORDY isn't necessary at this point
anyway. Make ata_pio_need_iordy() return zero if it's being called
for reset.
This fixes bko#11703. Reported and tracked down by Daniel Gnoutcheff
and Constantine Gavrilov.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Daniel Gnoutcheff <gnoutchd@union.edu>
Cc: Constantine Gavrilov <constantine.gavrilov@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch provides PATA driver for CompactFlash interface in True IDE
mode on AT91SAM9260 SoC.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1. add defaults to description where possible
2. add value definition (off=0, on=1) where missing
v2: reformatted as per request by Jeff Garzik <jgarzik@pobox.com>
"Enable foo (0=off, 1=on [default])"
Signed-off-by: Evgeni Golov <sargentd@die-welt.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During cluster testing, one QP was not closed, as FIN is not handled
properly when its rexmit count expires or in some cases when RST is is
received after sending FIN. The reason is that the cm_id does not get
decremented under these conditions.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In nes_query_device(), max_qp_init_rd_atom is incorrectly set to
max_qp_wr. This was found when a test application had a dapl async
event error.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
