This change enables PCI root complex support for TILEPro. Unlike
TILE-Gx, TILEPro has no support for memory-mapped I/O, so the PCI
support consists of hypervisor upcalls for PIO, DMA, etc. However,
the performance is fine for the devices we have tested with so far
(1Gb Ethernet, SATA, etc.).
The <asm/io.h> header was tweaked to be a little bit more aggressive
about disabling attempts to map/unmap IO port space. The hacky
<asm/pci-bridge.h> header was rolled into the <asm/pci.h> header
and the result was simplified. Both of the latter two headers were
preliminary versions not meant for release before now - oh well.
There is one quirk for our TILEmpower platform, which accidentally
negotiates up to 5GT and needs to be kicked down to 2.5GT.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This change adds the first network driver for the tile architecture,
supporting the on-chip XGBE and GBE shims.
The infrastructure is present for the TILE-Gx networking drivers (another
three source files in the new directory) but for now the the actual
tilegx sources are waiting on releasing hardware to initial customers.
Note that arch/tile/include/hv/* are "upstream" headers from the
Tilera hypervisor and will probably benefit less from LKML review.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Vegard Nossum found a unix socket OOM was possible, posting an exploit
program.
My analysis is we can eat all LOWMEM memory before unix_gc() being
called from unix_release_sock(). Moreover, the thread blocked in
unix_gc() can consume huge amount of time to perform cleanup because of
huge working set.
One way to handle this is to have a sensible limit on unix_tot_inflight,
tested from wait_for_unix_gc() and to force a call to unix_gc() if this
limit is hit.
This solves the OOM and also reduce overall latencies, and should not
slowdown normal workloads.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only make swapper_pg_dir readonly and pinned when generic x86 architecture code
(which also starts on initial_page_table) switches to it. This helps ensure
that the generic setup paths work on Xen unmodified. In particular
clone_pgd_range writes directly to the destination pgd entries and is used to
initialise swapper_pg_dir so we need to ensure that it remains writeable until
the last possible moment during bring up.
This is complicated slightly by the need to avoid sharing kernel PMD entries
when running under Xen, therefore the Xen implementation must make a copy of
the kernel PMD (which is otherwise referred to by both intial_page_table and
swapper_pg_dir) before switching to swapper_pg_dir.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The patch enables ALC887-VD to use the DAC at nid 0x26,
which makes it possible to use this DAC for e g Headphone
volume.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return PTR_ERR(omap3pandora_dac_reg) instead of 0 if regulator_get failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MCLKDIV bit of Register 04h Clocking1:
0 : Divide by 1
1 : Divide by 2
Thus in the case of freq <= 16500000, we should clear MCLKDIV bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
DACSLOPE bit of Register 06h ADC and DAC Control 2:
0: Normal mode
1: Sloping stop-band mode
Thus in the case of normal mode, we should clear DACSLOPE bit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
MX51 Babbage has an AT45DB321 SPI Flash connected to eCSPI1.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Code called from an initcall can be maybe called for
machines it's not intended for. So check for valid
machines and return gracefully if an incompatible machine
is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Code called from an initcall can be maybe called for
machines it's not intended for. So check for valid
machines and return gracefully if an incompatible machine
is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Code called from an initcall can be maybe called for
machines it's not intended for. So check for valid
machines and return gracefully if an incompatible machine
is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds a Kconfig option for the avic irq controller
and lets the SoCs that need it select this option.
Also, as we have two irq controllers for i.MX, irq.c is not
appropriate anymore, so rename it to avic.c
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
PHYS_OFFSET may become a variable once the runtime PHYS_OFFSET
patch is merged, so use MX51_PHYS_OFFSET for boot_params.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit "ARM: i.MX IOMUX-V3 replace struct pad_desc with bitmapped cookie"
(b705cb4d42e95a4a43a8945571c8613e71526c3d) introduced a typo which was
preventing my efikamx to boot. This patch is fixing that.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efikamx board is using a gpio to reset the board so add support
for it
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On efikamx, uboot is stored on a nor spi flash. Add support for it
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for power key button of the efika mx. It's connected
on GPIO 2 31.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efika mx a 3 leds (1 blue, 1 red, 1 green) connected on GPIOS 3 13/14/15.
Also, some special care is done for default trigger of blue led for mmc as
the mmc host used is different between hw revisions
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The efika mx is using a esdhc host for mmc support. Now that the sdhci
has support for it, enable it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- add definition to configure pads as ESDHC{1,2} WP and CD
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- ALT0 is used to set GPIO mode of GPIO_1_{2,3,4,5,6,7,8,9} but it's ALT1
for GPIO_1_{0,1}.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
read board id value from the GPIO3_16/17/11
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the mx31_3ds board the touchscreen feature is provided by MC13783 PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.
The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The file is not needed.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sis_main.c is always compiled, so we can check Kconfig options there.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Get rid of one more wrapper.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is no need to alias CONFIG #defines.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It's not needed anymore with SIS_XORG_XF86 gone.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Delete code for compiling the driver for X.org/XFree86. The development
has forked, so there is no point keeping this code in the tree.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If pci_map_rom() fails, there is some fallback code that basically
duplicates pci_map_rom() on non-x86 platforms. No point in that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Delete a workaround for a PCI ROM bug that has been fixed ages ago by
the commit 761a3ac08c.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The PLLC2 clock was utilizing the same sort of enable/disable without
regard to usecount approach that the FSIDIV clock was when being used as
a PLL pass-through. This forces the enable/disable through the clock
framework, which now prevents the clock from being ripped out or modified
underneath users that have an existing handle on it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
