Expose an hardreset API from hwmod in order to assert / deassert all the
individual reset lines that belong to an hwmod. This API is needed by
some of the more complicated processor drivers, e.g., DSP/Bridge,
Syslink, etc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Force the softreset of every IPs during the _setup phase.
IPs that cannot support softreset or that should not
be reset must set the HWMOD_INIT_NO_RESET flag in the
hwmod struct.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Most processor IPs does have a hardreset signal controlled by the PRM.
This is different of the softreset used for local IP reset from the
SYSCONFIG register.
The granularity can be much finer than orginal HWMOD, for ex, the IVA
hwmod contains 3 reset lines, the IPU 3 as well, the DSP 2...
Since this granularity is needed by the driver, we have to ensure
than one hwmod exist for each hardreset line.
- Store reset lines as hwmod resources that a driver can query by name like
an irq or sdma line.
- Add two functions for asserting / deasserting reset lines in hwmods
processor that require manual reset control.
- Add one functions to get the current reset state.
- If an hwmod contains only one line, an automatic assertion / de-assertion
is done.
-> de-assert the hardreset line only during enable from disable transition
-> assert the hardreset line only during shutdown
Note: The hwmods with hardreset line and HWMOD_INIT_NO_RESET flag must be
kept in INITIALIZED state.
They can be properly enabled only if the hardreset line is de-asserted
before.
For information here is the list of IPs with HW reset control
on an OMAP4430 device:
RM_DSP_RSTCTRL
1,1,'RST2','RW','1','DSP - MMU, cache and slave interface reset control'
0,0,'RST1','RW','1','DSP - DSP reset control'
RM_IVA_RSTCTRL
2,2,'RST3','RW','1','IVA logic and SL2 reset control'
1,1,'RST2','RW','1','IVA Sequencer2 reset control'
0,0,'RST1','RW','1','IVA sequencer1 reset control'
RM_IPU_RSTCTRL
2,2,'RST3','RW','1','IPU MMU and CACHE interface reset control.'
1,1,'RST2','RW','1','IPU Cortex M3 CPU2 reset control.'
0,0,'RST1','RW','1','IPU Cortex M3 CPU1 reset control.'
PRM_RSTCTRL
1,1,'RST_GLOBAL_COLD_SW','RW','0','Global COLD software reset control.'
0,0,'RST_GLOBAL_WARM_SW','RW','0','Global WARM software reset control.'
RM_CPU0_CPU0_RSTCTRL
RM_CPU1_CPU1_RSTCTRL
0,0,'RST','RW','0','Cortex A9 CPU0&1 warm local reset control'
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made the hardreset functions static; moved the register
twiddling into prm*.c functions in previous patches; changed the
function names to conform with hwmod practice]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch adds hard-reset support for processor modules (e.g., DSP, IVA)
on OMAP2/3 platforms. It's based on the OMAP4 hard-reset support that Benoît
developed in the previous patch.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Most processor modules (e.g., DSP, IVA, IPU) on OMAPs can be reset
under the control of the PRM. This patch adds an API for this purpose
for OMAP4 devices:
int omap4_prm_is_hardreset_asserted(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_assert_hardreset(void __iomem *rstctrl_reg, u8 shift);
int omap4_prm_deassert_hardreset(void __iomem *rstctrl_reg, u8 shift);
This API is intended to be used only by the hwmod code - a subsequent
patch will add that support to hwmod.
This patch is a collaboration between Benoît Cousson <b-cousson@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Since OMAP4 is using an absolute address, the current PRM accessors
are not useable.
OMAP4 adaptation for these API are currently ongoing, so define temp
version until the proper ones are defined.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently omap_hwmod_mutex is being used to protect both the list
access/modification and concurrent access to hwmod functions. This
patch separates these two types of locking.
First, omap_hwmod_mutex is used only to protect access and
modification of omap_hwmod_list. Also cleaned up some comments
referring to this mutex that are no longer needed.
Then, for protecting concurrent access to hwmod functions, use a
per-hwmod mutex. This protects concurrent access to a single hwmod,
but would allow concurrent access to different hwmods.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: added structure documentation; changed mutex variable
name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP4 platform has different register bits for Warm and Cold Resets.
Write one into appropriate bits.
Signed-off-by: Rajeev Kulkarni <rajeevk@ti.com>
Cc: Leed Aguilar <leed.aguilar@ti.com>
[b-cousson@ti.com: Change the define with the proper one from omap4 headers]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
The reset function wrongly used the state flag as a bit mask and was trying
to re-enable after a reset.
hwmod is still enabled for the PRCM point of view after a softreset
so there is no need to re-enable.
Remove the state check from omap_hwmod_reset since the _reset
function is checking that as well and in addition can generate
a warning
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
[b-cousson@ti.com: remove the wrong test, remove the re-enable]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The disable function was disabling clocks and dependencies
from both enable and idle state. Since idle function is already
disabling both, an enable -> idle -> disable sequence will
try to disable twice the clocks and thus generate a
"Trying disable clock XXX with 0 usecount" warning.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Implement the new runtime PM framework as a thin layer on top of the
omap_device API. OMAP specific runtime PM methods are registered with
the as custom methods on the platform_bus.
In order to determine if a device is an omap_device, its parent device
is checked. All omap_devices have a new 'omap_device_parent_ device
as their parent device, so checking for this parent is used to check
for valid omap_devices. If a device is an omap_device, then the
appropriate omap_device functions are called for it. If not, only the
generic runtime PM functions are called.
Device driver's ->runtime_idle() hook is called when the runtime PM
usecount reaches zero for that device. Driver's ->runtime_suspend()
hooks are called just before the device is disabled (via
omap_device_idle()), and device driver ->runtime_resume() hooks are
called just after device has been enabled (via omap_device_enable().)
OMAP4 build support from Rajendra Nayak <rnayak@ti.com>.
OMAP2 build support from Charulatha V <charu@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Charulatha V <charu@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes omap3 hardcodings from pm-debug.c
so that enabling PM debugfs support does break compilation
for other OMAP's. This is a preparatory patch for supporting
OMAP4 pm entries through PM debugfs.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cleanup indentation around IO wakeup enable, the '\' terminator is
not required in C when wrapping an expression past end-of-line.
Whitespace change only.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The dma request line attribute was named dma channel, which leads
to confusion with the real dma channel definition.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch addresses below things
- Renaming existing omap3_defconfig which has OMAP2, OMAP3 and OMAP4 builds
enabled to more appropriate name 'omap2plus_defconfig'
- L1 cache shift is suppose to be 5 on OMAP4 where as it is 6 on previous
OMAPs. Keeping it to 5 is safer option for OMAP4 and previous OMAPs. For
OMAP3 only build the shift would be still 6
- Enable needed Errata's for OMAP4 to work with DMA based device drivers
CONFIG_PL310_ERRATA_588369=y
CONFIG_ARM_ERRATA_720789=y
- Enable the Micrel ethernet controller
CONFIG_KS8851=y
CONFIG_KS8851_MLL=y
With above three changes, OMAP4 ethernet, mmc etc works reliably.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 5a5f561 (convert OMAP3 PRCM macros to the _SHIFT/_MASK suffixes)
mistakenly removed the check for PER when disabling the IO chain.
During idle, if the PER powerdomain transitions into a lower state
and CORE does not, the IO pad wakeups are not being disabled in
the idle path after they are enabled. This can happen with the
lower C-states when using CPUidle for example.
This patch ensures that the check for disabling IO wakeups also checks
for PER transitions, matching the check done to enable IO wakeups.
Found when debugging PM/CPUidle related problems reported by Ameya
Palande <ameya.palande@nokia.com>. Problems were triggered
particularily on boards with UART2 consoles (n900, Overo) since UART2
is in the PER powerdomain.
Tested on l-o master (omap3_defonfig + CONFIG_CPU_IDLE=y) as well
as with current PM branch. Boards tested: n900, Overo, omap3evm.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@nokia.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description to clarify the transistion]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we get the following error when enabling CONFIG_SMP
for omap3_defconfig:
arch/arm/kernel/entry-armv.S: Assembler messages:
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ipi r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ltirq r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ipi r0,r6,r5,lr'
arch/arm/kernel/entry-armv.S:48: Error: bad instruction `test_for_ltirq r0,r6,r5,lr'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Otherwise we get the following error with omap3_defconfig and CONFIG_SMP:
Error: selected processor does not support `sev'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
cpu_is_omap3517() and cpu_is_omap3505() are the subgroups of cpu_is_omap34xx(),
so we should check cpu_is_omap3517() and cpu_is_omap3505() first, then check
cpu_is_omap34xx().
Otherwise, All AM35XX (Sitara) clocks do not get registered and device drivers
(ti_hecc, etc...) that depend on those clocks are failing to get the clock and
end up with non working device.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong placement of break causes all revisions of 3630 to be
detected as 3630 es1.2, we need to break main loop if we have
an identified chip, default falls through as in the rest of the
switches in this function.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Manjunath K <manjugk@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pandora has TI WL1251 attached on MMC3, which is non-standard SDIO chip.
Make use MMC_QUIRK_NONSTD_SDIO to tell SDIO core about it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
With recent changes happened in OMAP2/3 DSS library for regulator interface, it
is required to define DSI regulator supply, without this DSS (in turn Fbdev)
fails to get regulator.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Remove kernel.h and module.h since they are not used correctly anyway.
Also, remove device.h since it comes along with platform_device.h
(always will I guess).
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
omap{1,2}-mailbox are modules that provide the 'omap-mailbox' driver.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
No need to dynamically register mailboxes one by one.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Will be useful to identify them later.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
OMAP4 ones messed up the organization.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
USBTLL Save-and-Restore is broken in 3630 ES1.0. Having it
enabled could result in incorrect register restores as
the OMAP exits off-mode. This could potentially result in
unexpected wakeup events.
(Refer 3630 errata ID i579)
This is fixed in ES1.1. So disable it for ES1.0s.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add revision detection for ES1.1 and ES1.2. Set default
revision as ES1.2.
Add CHIP_GE_OMAP3630ES1_1 to detect revisions 1.1 and later.
This is needed for at least one feature that is broken in
3630ES1.0 but exists on older (3430 ES3.1) and newer revisions.
Additionally, update some of the CHIP_GE_* macros to use other
macros for ease of maintenance.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Manjunatha GK <manjugk@ti.com>
[tony@atomide.com: update to remove fallthrough handling]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most OMAP3-based boards use exactly the same code for .map_io method in
the machine_desc structure.
This patch introduces omap3_map_io and updates board-* files to use it
as .map_io method.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only difference between them is the physical address of the
uart4 port, which is only present in 36xx chips.
We don't really need to care about keeping these 2 functions, since
the decision to use uart4 is more cleanly done later when we do have
access to omap_revision variable.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: added comment for the uart4_phys]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now we use a memory address to store the debug port info, So we need
to read/write this address when we choose DEBUG_LL. When MMU isn't
enable(I.E. the begining part of init stage of the linux kernel boot),
we need to access physical address instead of virtual address,
otherwise the kernel will crash.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a missing break at end of switch statement. At the moment it is a
fall through to WARN_ON(1) and return -EEXIST.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
add support for NAND, OneNAND, NOR on omap 3630-sdp board.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds NAND support to ZOOM2 board.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rename board-sdp-flash.c(board-flash.c) and board-sdp.h(board-flash.h) to
used by other board e.g. zoom
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Board file modified for not to provide gpmc phys_base address to nand driver.
The gpmc_nand_init funciton is now used to detect the nand and required to
adopt _prob function as in nand/omap2.c
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes direct reference of gpmc address from generic nand platform code.
Nand platform code now uses wrapper functions which are implemented in gpmc module.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
few functions added in gpmc module and to be used by other drivers like NAND.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3530 CBB package can have GPIO126 muxed on 2 pins: mmc1_dat4 and
cam_strobe. This causes a problem with current multipath GPIO mux
handling, which muxes both pins as GPIO126 and makes the GPIO unusable.
Fix this by not muxing any pins if multipath GPIO is detected and
just print a warning instead. It's up to board files to set correct
mux using omap_mux_init_signal and pin name.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The devkit8000 boards often come with empty EEPROM thus without
valid ethernet MAC address. The DIE id to MAC formula is copied from
u-boot.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3505/3517 doesn't have IO wakeup capability, so we do not need to set
the bit OMAP3430_EN_IO and the bit OMAP3430_EN_IO_CHAIN in the register
PM_WKEN_WKUP when the system enters suspend state.
Tested on AM3517EVM and OMAP3530EVM.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap24xx_check_revision, omap3_check_features,
omap3_check_revision, omap4_check_revision, omap3_cpuinfo
are not used elsewhere, it should be static
Also fixes the following sparse warnings:
arch/arm/mach-omap2/id.c:105:13: warning: symbol 'omap24xx_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:167:13: warning: symbol 'omap3_check_features'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:189:13: warning: symbol 'omap3_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:270:13: warning: symbol 'omap4_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:300:13: warning: symbol 'omap3_cpuinfo'
was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The original patch got truncated when applied from patchwork.kernel.org
as discussed at:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg28953.html
This patch supplies the missing chunks.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
[tony@atomide.com: added more info to the patch description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix GPIO numbers and smc91x for 2430sdp. The earlier code
had cut and paste errors from 3430sdp code. Also, 2430
has five GPIO banks for a total of 160 GPIO lines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds cpu hotplug support for OMAP4430. Only CPU inactive
state is supported as a low power state in the basic hot-plug support
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a secure API to read AuxCoreBoot0 register to
check the cpu boot status. It also moves the other smc APIs
to common omap44xx-smc.S. This APIs should not be marked as
__INIT because we need these to be present for CPU hotplug
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for basic suspend doing a CPUx wfi
for OMAP4. All powerdomains are for now are kept programmed
in ON state.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6):
UART module MDR1 register access can cause a dummy underrun
condition which could result in a freeze in the case of IrDA
communication or if used as UART, corrupted data.
Workaround is as follows for everytime MDR1 register is changed:
* setup all required UART registers
* setup MDR1.MODE_SELECT bit field
* Wait 5 L4 clk cycles + 5 UART functional clock cycles
* Clear the Tx and RX fifo using FCR register
Note: The following step is not done as I am assuming it is not
needed due to reconfiguration being done and there is no halted
operation perse.
* Read if required, the RESUME register to resume halted operation
Based on an earlier patch at:
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0c
Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
introduce silicon specific quirks as a errata handling mechanism
as a start UART_ERRATA_FIFO_FULL_ABORT is used to handle the override
for fifo full condition for rx and tx.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the following sparse warnings by declaring attr as static:
arch/arm/mach-omap2/serial.c:627:1: warning: symbol 'dev_attr_sleep_timeout'
was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialization of pointer should be done with NULL. Removes sparse
warnings:
arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds context save/restore for mcr register as state of mcr register
is lost after core off.
Signed-off-by: Govindraj R <govindraj.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add initial support for the OMAP4 based Panda Board.
Signed-off-by: David Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.
This patch fixes the same and has VAUX1 as supply to MMC2 card.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit will enable usage of tsl2563 ambient light sensor on Nokia N900.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With these and upcoming change to tpa6130a2 driver it's possible to add
support for the TPA6130A2 headphone amplifier.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is REGULATOR_SUPPLY macro available for initializing the struct
regulator_consumer_supply so use it where applicable (all other supplies
than vdds_sdi) as it improves the readability.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Proper operation of the tlv320aic3x audio codec requires that reset
sequencing is done in pair with supply voltages when using the regulator
framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x
data.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.
Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.
Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.
Prepare for these by defining the V28 as always_on regulator.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for NAND and wifi, also setup all GPIOs
needed to use the wifi chip.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update gpio-keys setup so it matches what is on default firmware.
Also make use of debounce feature in gpio-keys instead of setting it
explicitly, as gpio-keys is now capable of using hardware debounce on
OMAPs thanks to recent gpiolib changes.
Also fix a sparce warning along the way.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM3.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM2.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update some minor documentation issues and update copyright for
omap_device/omap_hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Add omap_device_get_mpu_rt_va(). This is intended to be used by
device drivers (currently, via a struct platform_data function
pointer) to retrieve their corresponding device's virtual base address
that the MPU should use to access the device. This is needed because
the omap_hwmod code does its own ioremap(), in order to gain access to
the module's OCP_SYSCONFIG register.
Add omap_hwmod_get_mpu_rt_va(). omap_device_get_mpu_rt_va() calls this
function to do the real work.
While here, rename struct omap_hwmod._rt_va to struct
omap_hwmod._mpu_rt_va, to reinforce that it refers to the MPU's
register target virtual address base (as opposed to, for example, the
L3's).
In the future, this belongs as a function in an omap_bus, so it is not
necessary to call this through a platform_data function pointer.
The use-case for this function was originally presented by Santosh
Shilimkar <santosh.shilimkar@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add IVA1 hwmod data for OMAP2420 and IVA2 hwmod data for 2430. The data
is based on Benoît Cousson's hwmod data for the OMAP3 IVA blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add hwmod data for IVA2 module on OMAP3.
Naming of "iva" instead of "iva2" to be aligned with OMAP4 naming done
by Benoit Cousson.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Replace all the struct that contain l3 with l3_main in order
to be consistent with the OMAP4 naming convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a new hwmod class for IVA devices. To be used when hwmods
are created for IVA2 on OMAP3.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Create simple omap_devices for the main processors and busses.
This is required to support the forth-coming device-based OPP
approach, where OPPs are managed and tracked at the device level.
Also, move these common PM init functions into a common_pm_init call
that is called as a device_initcall(). The PM init is done at this level
to ensure that the driver core is initialized before initialized.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: sparse warnings cleaned up; newly-created functions moved
from mach-omap2/io.c to mach-omap2/pm.c; newly-created functions renamed
to start with "omap2" rather than "omap"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Enable omap_device layer support for OMAP4, so that drivers can
use them to enable/idle/shutdown devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On kernels that don't use the omap_device_enable() calls to enable
devices, leave all on-chip devices enabled in hwmod _setup().
Otherwise, accesses to those devices are likely to fail, crashing the
system. It's expected that kernels built without CONFIG_PM_RUNTIME
will be the primary use-case for this. This functionality is
controlled by adding an extra parameter to omap_hwmod_late_init().
This patch is based on the patch "OMAP: hwmod: don't auto-disable
hwmod when !CONFIG_PM_RUNTIME" by Kevin Hilman
<khilman@deeprootsystems.com>.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some hwmods may need to be idled/enabled in atomic context, so
non-locking versions of these functions are required.
Most users should not need these and usage of theses should be
controlled to understand why access is being done in atomic context.
For this reason, the non-locking functions are only exposed at the
hwmod level and not at the omap-device level.
The use-case that led to the need for the non-locking versions is
hwmods that are enabled/idled from within the core idle/suspend path.
Since interrupts are already disabled here, the mutex-based locking in
hwmod can sleep and will cause potential deadlocks.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the lastest OMAP4 hwmod data file, the _hwmod was removed
in order to save some memory space and because it does not
bring a lot.
Align OMAP2420, 2430 and 3430 data files with the same convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since these hwmods do not have IDLEST, set the HWMOD_NO_IDLEST flag,
otherwise _enable() will fail due to failing _wait_target_ready().
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP24xx, the polarity for the IDLEST bits is opposite of OMAP3.
The mask used to check this was using the bit position instead of the
bit mask.
This patch fixes the problem by using the bit mask instead of the bit
field.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We need to wait on the IDLEST bit after the clocks are enabled
before attempting to access any register.
Currently, the USBTLL i-clock ops uses the clkops_omap2_dflt_wait,
while the USBTLL f-clock ops uses clkops_omap2_dflt. If the
i-clock is enabled first, the clkops_omap2_dflt_wait is
short-circuited as the companion f-clock is not enabled.
This can cause a data abort if the IDLEST has not transitioned,
and we try to access a USBTLL register.
Since the USBTLL i-clock and f-clock could be enabled in any order,
this is a bug. Fix it by changing the clkops for the f-clock.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 3fea60261e ("Input: twl40300-keypad - fix handling of "all
ground" rows") broke compilation as I managed to use non-existent
keycodes.
Reported-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - relax capability ID checks on newer hardware
Input: twl40300-keypad - fix handling of "all ground" rows
Input: gamecon - reference correct pad in gc_psx_command()
Input: gamecon - reference correct input device in NES mode
Input: w90p910_keypad - change platfrom driver name to 'nuc900-kpi'
Input: i8042 - add Gigabyte Spring Peak to dmi_noloop_table
Input: qt2160 - rename kconfig symbol name
Add a dummy clk definition for the APB pclk signal on all platforms
using the AMBA bus infrastructure. This ensures that these platforms
continue to work when the core amba bus code controls the APB pclk.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Nokia RX51 board code (arch/arm/mach-omap2/board-rx51-peripherals.c)
defines a key map for the matrix keypad keyboard. The hardware seems to
use all of the 8 rows and 8 columns of the keypad, although not all
possible locations are used.
The TWL4030 supports keypads with at most 8 rows and 8 columns. Most keys
are defined with a row and column number between 0 and 7, except
KEY(0xff, 2, KEY_F9),
KEY(0xff, 4, KEY_F10),
KEY(0xff, 5, KEY_F11),
which represent keycodes that should be emitted when entire row is
connected to the ground. since the driver handles this case as if we
had an extra column in the key matrix. Unfortunately we do not allocate
enough space and end up owerwriting some random memory.
Reported-and-tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Devkit8000 uses the TPS65930 and not the TWL4030.
The TPS65930 uses only a subset of the power supplies
of the TWL4030.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_board_config is no longer used and thats why empty.
This patch removes the empty omap_board_config.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using the macro gpio_is_valid for check of valid gpio pins.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.
vaux2 is not used on Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VDVI power supply is no longer needed in
board code with the new DSS2 interface.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch corrects the LCD reset pin configuration.
Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch corrects the DVI-D output setup of Devkit8000
Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Corrected the wrong power supplies in devkit8000 code.
Add supply for ads7846 to support the new regulator framework for
touchscreen.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MACH_OMAP2_H4_USB1 doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MACH_OMAP_H4_OTG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_STI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_IR doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated for new mux code]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use new mux functions for that. There are no other known 2430 boards
that need this mux.
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the new mux function for that.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we get pin muxing out of plat-omap and can convert H4 to use the
new mux functions.
Note that it should be safe to assume we can mux all the keypad pins
except on H4 which may have Menelaus connected.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make omap2 FS USB code use new mux functions. Do not mux usb2_tllse0
as it has multiple options.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add data for 2430. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add data for 2420. Big thanks to Paul Walmsley <paul@pwsan.com>
for generating usable mux data out of TRMs.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like 24xx uses mode3 instead of mode4 for muxable GPIO pins.
This will be needed when 24xx mux code is converted to use the new
mux functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omap2 FS USB platform init code into mach-omap2/usb-fs.c. This will
allow further work later on to use omap hwmod for initializing the
device.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2.6.34-rc6 kernel has the Ducati mmu irq define name changed, which is
resulting in compilation error.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
The function prefix "omap2_iommu_" indicates that the prefixed
function belongs to "omap2_iommu_ops" to provide iommu basic
functionalities for the above layers. It's better to avoid the
prefixed function called in the same prefixed ones internally, like
nested here. Now "iommu_disable" is called just after fault_isr() in
the above layer. This is a little bit more sensible to keep the
consistency of module layers.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
In order to enable TLB miss interrupt, the TWL should be
disabled. This patch provides the functionality to get the
MMU fault interrupt for a TLB miss in the cases where the
users are working with the locked TLB entries and with TWL
disabled.
New interface is added to select twl and to enable TLB miss
interrupt.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Ramesh Gupta <grgupta@ti.com>
Signed-off-by: Hiroshi Doyu <Hiroshi.DOYU@nokia.com>
Revise the IRQ mask definitions to handle the MMU faults related
to TWL fault as well as TLB miss fault.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi Doyu <Hiroshi.DOYU@nokia.com>
