Use container_of instead of casting first structure member.
ARM cross-compiled but untested.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX change FEC alignment requirement.
i.MX6 SX change internal bus from AHB to AXI.
It require RX buffer must be 64 bytes alignment.
And remove TX buffer alignment requirement.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string "fsl,imx6sx-fec" for i.MX6SX.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues.
For tx queues: ring 0 -> best effort
ring 1 -> Class A
ring 2 -> Class B
For rx queues:
ring 0 -> best effort
ring 1 -> receive VLAN packet with classification match
ring 2 -> receive VLAN packet with classification match
Add enet-avb IP multiqueue support for the driver.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For i.MX6SX enet use AXI bus, reset MAC will make system bus dead
if ENET-AXI bus has pending access (AHB bus should not have such issue).
So, disable enet with AVB MAC instead of reset MAC itself.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
initilized all queues according to queue number get from DT file.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Duan Fugang <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the tx/rx queue number is 1, user can config the queue number
at DTS file like this:
fsl,num-tx-queues=<3>;
fsl,num-rx-queues=<3>
Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
interface to allocate and set up an Ethernet device.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just change data structure to support multi-queue.
Only 1 queue enabled.
Ethernet multiqueue mechanism can improve performance in SMP system.
For single hw queue, multiqueue can balance cpu loading.
For multi hw queues, multiple cores can process network packets in parallel,
and refer the article for the detail advantage for multiqueue:
http://vger.kernel.org/~davem/davem_nyc09.pdf
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add enet AVB feature macro define for imx6sx.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6sx enet has below clocks for user config:
clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz
clk_ahb: enet system clock, it is enet AXI clock for imx6sx.
For imx6sx, it alos is the clock source of interrupt coalescing.
The clock range: 200Mhz ~ 266Mhz.
clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode,
the refrence clock is 125Mhz coming from internal PLL or external.
In i.MX6sx-arm2 board, the clock is from internal PLL.
clk_ref is optional, depends on board.
clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz
clock for phy. clk_enet_out is optional, depends on chip and board.
clk_ptp: 1588 ts clock. It is optional, depends on chip.
The patch add clk_ref to distiguish the different clocks.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.
FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.
To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.
i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.
To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
My series to fix the reference counting of dt nodes introduced a build
failure. Fix it.
Fixes: fa310789a4 ("net: ucc_geth: drop acquired references in probe error path and remove")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This matches what the other drivers using fixed-link support do and
restores the behaviour before commit 87009814cd ("ucc_geth: use the
new fixed PHY helpers") for the affected device trees (i.e. no
phy-handle and no fixed-link).
Fixes: 87009814cd ("ucc_geth: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver attaches to a device that has a phy handle the probe
routine returns with a reference to that node. This reference is
correctly dropped in the error path and the remove function. In the
fixed phy case however no reference is acquired and so the error path
might drop a reference the driver isn't holding. Fix that by getting a
reference to the MAC.
Fixes: 87009814cd ("ucc_geth: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ucc_geth_probe function assigns to ug_info->tbi_node and
ug_info->phy_node a value returned by of_parse_phandle which returns a
new reference. Put this reference again in the error path of
ucc_geth_probe and when removing the device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that fs_enet_probe is left with a reference to the phy node.
In the presence of a phy handle this is already the case as
of_parse_phandle returns a reference. In the fixed phy case a call to
of_node_get is necessary. Otherwise the error path and remove function
drop a reference the driver isn't holding.
Fixes: bb74d9a4a8 ("fs_enet: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The line before the changed if condition is:
priv->phy_node = of_parse_phandle(np, "phy-handle", 0);
. If this call succeeds priv->phy_node must not be overwritten in the if
block; otherwise the reference to the node returned by of_parse_phandle
is lost. So add a check that the if block isn't executed in this case.
Furthermore in the fixed phy case no reference is aquired for phy_node
resulting in an of_node_put without holding a reference. To fix that,
get a reference on the MAC dt node.
Fixes: be40364544 ("gianfar: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put is a noop when being called with NULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc new goodies for 3.17. The short story:
The biggest bit is Michael removing all of pre-POWER4 processor
support from the 64-bit kernel. POWER3 and rs64. This gets rid of a
ton of old cruft that has been bitrotting in a long while. It was
broken for quite a few versions already and nobody noticed. Nobody
uses those machines anymore. While at it, he cleaned up a bunch of
old dusty cabinets, getting rid of a skeletton or two.
Then, we have some base VFIO support for KVM, which allows assigning
of PCI devices to KVM guests, support for large 64-bit BARs on
"powernv" platforms, support for HMI (Hardware Management Interrupts)
on those same platforms, some sparse-vmemmap improvements (for memory
hotplug),
There is the usual batch of Freescale embedded updates (summary in the
merge commit) and fixes here or there, I think that's it for the
highlights"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
powerpc/eeh: Export eeh_iommu_group_to_pe()
powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
powerpc: Reduce scariness of interrupt frames in stack traces
powerpc: start loop at section start of start in vmemmap_populated()
powerpc: implement vmemmap_free()
powerpc: implement vmemmap_remove_mapping() for BOOK3S
powerpc: implement vmemmap_list_free()
powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
powerpc/book3s: handle HMIs for cpus in nap mode.
powerpc/powernv: Invoke opal call to handle hmi.
powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
powerpc/iommu: Fix comments with it_page_shift
powerpc/powernv: Handle compound PE in config accessors
powerpc/powernv: Handle compound PE for EEH
powerpc/powernv: Handle compound PE
powerpc/powernv: Split ioda_eeh_get_state()
powerpc/powernv: Allow to freeze PE
powerpc/powernv: Enable M64 aperatus for PHB3
powerpc/eeh: Aux PE data for error log
...
Fix one misspelled word reported by codespell.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the CONFIG_PM_SLEEP ifdef by annotating the suspend/resume functions
with '__maybe_unused' in order to keep the code simpler and shorter.
While at it, declare the suspend/resume functions in a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both transmit and receive use the same infrastructure for calculating
the packet timestamp. Rather than duplicating the code, provide a
function to do this common work. Model this function in the Intel
e1000e version which avoids calling ns_to_ktime() within the spinlock;
the spinlock is critical for timecounter_cyc2time() but not
ns_to_ktime().
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless status check in the transmit reap path - we have
already checked that the BD_ENET_TX_READY bit is clear, and as the
hardware only ever clears this bit, there is no way this test can ever
be true.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we timeout on transmit, it would be useful to dump the transmit
ring, so we can see the ring state. This can be helpful to diagnose
the cause of transmit timeouts.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to merge two separate preprocessor conditionals together.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of "better implementation of iMX6 ERR006358 quirk", we no longer have
a requirement for a delayed work. Moreover, the work is now only used
for timeout purposes, so the timeout flag is also pointless - we set it
each time we queue the work, and the work clears it.
Replace the fec_enet_delayed_work struct with a standard work_struct,
resulting in simplified timeout handling code.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a (delayed) workqueue for ERR006358 is not correct - a work queue
is a single-trigger device. Once the work queue has been scheduled, it
can't be re-scheduled until it has been run. This can cause problems -
with an appropriate packet timing, we can end up with packets queued,
but not sent by the hardware, resulting in the transmit timeout firing.
Re-implement this as per the workaround detailed in the ERR006358
documentation - if there are packets waiting to be sent when we service
the transmit ring, and we see that the transmitter is not running,
kick the transmitter to run the pending entries in the ring.
Testing here with a 10Mbit half duplex link sees the resulting iperf
TCP bandwidth increase from between 1 to 2Mbps to between 8 to 9Mbps.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many places call fec_restart() with the second parameter being some kind
of previously saved duplex value, but only two places call it with some
other setting. This is at odds with how the other link settings are
handled, and used to be racy before the rtnl locks were added to
fec_restart()'s various call paths.
Clean this up so all link capabilities are handled in the same way -
saved into the fec_enet_private structure, and then fec_restart() acts
on those settings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link goes down, the adjust_link method will be called, but
there is no synchronisation to ensure that we won't be processing some
last remaining packets via the NAPI handlers while performing a reset of
the device.
Add the necessary synchronisation to ensure that packet processing
is complete before we stop and reset the FEC.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the features (receive checksumming) requires the hardware to be
reprogrammed, and also changes the checks in the receive packet
processing.
The current implementation has a race - fec_set_features() changes the
flags which alter the receive packet processing while the adapter is
active, and potentially receiving frames. Only after we've modified
the software flag do we shutdown and reconfigure the hardware.
This can lead to packets being received and marked with a valid checksum
(via CHECKSUM_UNNECESSARY) when the hardware checksum validation has not
yet been enabled.
We must quiesce the device, then change the software configuration for
this feature, and then resume the device if it was previously running.
The resulting code structure also allows us to add other configuration
features in this path without having to quiesce and resume the network
interface and device.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_set_features() calls fec_stop() to stop the transmit ring while the
transmit queue is still active. This can lead to the transmit ring
being restarted by an intervening packet queued for transmission, or
by the tx quirk timer expiring.
Fix this by disabling NAPI (which ensures that the NAPI handlers are
not running), and then take the transmit lock while we stop and
restart the adapter (which prevents new packets being queued).
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_suspend() calls fec_stop() to stop the transmit ring while the
transmit packet processing is still active. This can lead to the
transmit queue being restarted by an intervening packet queued for
transmission, or by the tx quirk timer expiring.
Fix this by disabling NAPI first, which will ensure that the NAPI
handlers are not running. Then, take the transmit lock before
detaching the netif device. This ensures that there are no races
with the transmit path - and also ensures that the watchdog won't
fire.
We can then safely stop the ethernet device itself, knowing that the
rest of the driver is safely shut down.
On resume, we bring the device back up in reverse order - we restart
the device, reattach the device (under the tx lock), and then enable
the NAPI handlers.
We also need to adjust the close function to cope with this new
sequence, so that it's possible to cleanly close down the driver
after the hardware fails to resume (eg, due to the regulator_enable()
or pinctrl calls in the resume path returning an error.)
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second stage to "move calls to quiesce/resume packet
processing out of fec_restart()", where we remove calls which are not
appropriate to the call site.
In the majority of cases, there is no need to detach and reattach the
interface as we are holding the queue xmit lock across the reset. The
exception to that is in fec_resume(), where we are already detached by
the suspend function. Here, we can remove the call to detach the
interface.
We also do not need to stop the transmit queue. Holding the xmit lock
is enough to ensure that the transmit packet processing is not running
while we perform our task. However, since fec_restart() always cleans
the rings, we call netif_wake_queue() (or netif_device_attach() in the
case of resume) just before dropping the xmit lock. This prevents the
watchdog firing.
Lastly, always call napi_enable() after the device has been reattached
in the resume path so that we know that the transmit packet processing
is already in an enabled state, so we don't call netif_wake_queue()
while detached.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the calls to quiesce and resume packet processing out of
fec_restart() to its call sites. This is the first step in a two stage
clean up of this code, where we just move the calls out of fec_restart()
without changing them. Not everywhere needs to issue these calls, and
not everywhere needs all of these calls to be issued.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling fec_restart() or fec_stop() while the device is down
or not present (iow suspended.)
Although the ndo_timeout method will only be called if the device is
present and running, we defer this to a work queue. The work queue
can run independently, and so needs to repeat these checks to ensure
that a restart doesn't occur after the device has been taken down or
detached for suspend. In this case, we call fec_restart() in the
resume path, so nothing is lost.
For fec_set_features, we add a call to fec_restart() in fec_enet_open()
to ensure that the hardware is appropriate programmed when the interface
is opened. fec_set_features() call should not occur while we're
suspended, so we don't have to worry about that case.
The adjust_link needs similar treatment - this also is called from a
work queue, which may be run independently after we have taken the
device down and detached it. In this case, we just mark the link
down and take no further action. We will reset things appropriately
once the device is up and running again, at which point we will receive
another adjust_link callback.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FEC is suspended, the device is detached. Upon resume failure,
the device is left in detached mode, possibly with some of the required
clocks not running. We don't want to be poking the device in that state
because as it may cause bus errors.
If the device is marked detached, avoid calling fec_stop().
This depends upon: "net:fec: improve safety of suspend/resume paths"
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should hold the rtnl lock while suspending, resuming or processing
the transmit timeout to ensure that nothing will interfere while we
bring up, take down or restart the hardware. The transmit timeout
could run if we're preempted during suspend.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_alloc_buffers() assumes that kmalloc() will never fail, which
is an invalid assumption. Fix this by implementing a common error
cleanup path, and use it to also clean up after failed bounce buffer
allocation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we do not double-free any allocations, and that any transmit
skbuffs are properly freed when we clean up the rings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid writing any state until we're certain we can proceed with the
transmission: this avoids writing mapping error address values to the
descriptors, or setting the skbuff pointer until we have successfully
mapped the skb.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate, and then map the receive skb before writing any data to the
ring descriptor or storing the skb. When freeing the receive ring
entries, unmap and free the skb, and then clear the stored skb pointer.
This means we have ring data and skb pointer in one of two states:
either both fully setup, or nothing setup.
This simplifies the cleanup, as we can use just the skb pointer to
indicate whether the descriptor is setup, and thus avoids potentially
calling dma_unmap_single() on a DMA error value.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls. At this point, the driver then clears
fep->opened. The NAPI poll function uses this to stop processing in
the receive path. Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.
Therefore, this variable serves no purpose, so let's remove it.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
