The code probably has been unindented at some point but rewrapping has not
been done. Do it now.
Also remove a useless memory allocation failure message.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide more debugging information on reading the frame layout.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Besides the image data, SMIA++ compliant sensors also provide embedded
data in form of registers used to capture the image. Store this
information for later use in frame descriptor and routing.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace plain value 2 with SMIAPP_PADS when referring to the number of
pads.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The initialisation of the source sub-device is somewhat different as it's
not created by the smiapp driver itself. Remove redundancy in initialising
the two kind of sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The information gathered during frame format reading will be required
earlier in the initialisation when it was available. Also return an error
if frame format cannot be obtained.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The smiapp_probe() is the sole caller of smiapp_init(). Unify the two.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the registered() callback failed, resources were left unaccounted for.
Fix this, as well as add unregistering the sub-devices in driver
unregistered() callback.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialise the sensor in probe. The reason why it wasn't previously done
in case of platform data was that the probe() of the driver that provided
the clock through the set_xclk() callback would need to finish before the
probe() function of the smiapp driver. The set_xclk() callback no longer
exists.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead, calculate how much is needed and then allocate the memory
dynamically.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The same pixel array size is required for the active format of each
sub-device sink pad and try format of each sink pad of each opened file
handle as well as for the native size rectangle.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the loop in sub-device registration and create each sub-device
explicitly instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This allows determining the number of pads in the entity based on the
sensor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Define the number of pads explicitly in initialising the sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify smiapp_init() by moving the initialisation of individual
sub-devices to a separate function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver has printk continuation lines for
debugging purposes. Since commit 563873318d
("Merge branch 'printk-cleanups'"), this won't work as expected
anymore. So, let's add KERN_CONT to those lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hardware does not decode the 16, 20 or 24 bit variety.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the V4L2_SUBDEV_FORMAT_TRY is used in set_fmt the width, height etc
would not be filled.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The media bus format reported by the adv7180 is wrong. Steve Longerbeam
posted a patch which changed the format to UYVY8_2X8 with the commit
message:
Change the media bus format from YUYV8_2X8 to UYVY8_2X8. Colors
now look correct when capturing with the i.mx6 backend. The other
option is to set the SWPC bit in register 0x27 to swap the Cr and Cb
output samples.
The rcar-vin driver was developed and tested with the adv7180 and
therefor suffers from the same issue, looking for the wrong media bus
format. The two errors corrected each other.
This patch takes Steve's patch and merge it with a fix for rcar-vin
driver. The rcar-vin driver is used used in together with the adv7180
och Koelsch and this ensures it will not break while fixing the adv7180
issue. I checked wit Steve and he was fine with me merging the patches.
ADV7180 parts:
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The new ad5820 driver uses #ifdef to hide the suspend/resume functions,
but gets it wrong when CONFIG_PM_SLEEP is disabled:
drivers/media/i2c/ad5820.c:286:12: error: 'ad5820_resume' defined but not used [-Werror=unused-function]
drivers/media/i2c/ad5820.c:274:12: error: 'ad5820_suspend' defined but not used [-Werror=unused-function]
This replaces the #ifdef with a __maybe_unused annotation that is
simpler and harder to get wrong, avoiding the warning.
Fixes: bee3d51156 ("[media] ad5820: Add driver for auto-focus coil")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow the sub-device to be probed asynchronously so a bridge driver that's
waiting for the device can be notified and its .bound callback executed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: H . Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The SPI driver looked a bit lonely in the config menu, and it didn't
support the autoselect. Shift things around a bit so it looks more logical.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver used integers for what boolean would have been a better fit.
Use boolean instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
SMIA++ supports 14 and 16 bits per pixel formats as well. Add support to
these formats in the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As the mt9m111 is now working as a standalone v4l2 subdevice sensor,
move it out of soc_camera directory and sever its dependency on
soc_camera.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mt9m111 being a camera sensor, its colorspace should always be SRGB, for
both RGB based formats or YCbCr based ones.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the soc_camera adherence. Mostly the change removes the power
manipulation provided by soc_camera, and instead :
- powers on the sensor when the s_power control is activated
- powers on the sensor in initial probe
- enables and disables the MCLK provided to it in power on/off
This patch also drops support for inverters on synchronisation and clock
lines. It is assumed, if any board ever needs such inverters, support
for them can be added in the future
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The clock framework is generally so well supported that there's no reason
to keep this one around.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch from the old gpio API to the new descriptor based gpiod API.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The data may now be const as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The clock may be provided by a driver which is yet to probe. Print the
actual error code as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is really configuration to the driver originating from DT or
elsewhere. Do not call it platform data.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Unify enforced 8-bit read access with that based on actual need.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver is using the struct v4l2_subdev_core_ops .registered_async
callback to register the connector entities and create the pad links
after the subdev entity has been registered with the media device.
But the .registered_async callback isn't needed since the v4l2 core
already calls the struct v4l2_subdev_internal_ops .registered callback
in v4l2_device_register_subdev(), after media_device_register_entity().
So, use the .registered() callback instead of the .registered_async()
that is going to be removed in a following patch since isn't needed.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to return error code -ENOMEM from the i2c client register error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The old cropcap video op is now only used to pass the pixelaspect
ratio, so rename it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace all calls to g/s_crop by calls to the get/set_selection pad ops.
Remove the old g/s_crop video ops since they are now no longer used.
The cropcap video op is now only used to pass pixelaspect information,
and is only needed if the pixelaspect is not 1:1.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some targets control the ADV7180 power pin via a gpio, so add
optional support for "powerdown" pin control.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue work_queue is involved in EDID (Extended Display
Identification Data) handling.
It has a single work item(&state->edid_handler) and hence
doesn't require ordering. It is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
&state->edid_handler is a self requeueing work item and it has been
been sync cancelled in ad9389b_remove() to ensure that nothing is
pending when the driver is disconnected.
The unused label err_unreg has also been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds support for AD5820 autofocus coil, found for example in
Nokia N900 smartphone.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Access to the interrupt page registers has been broken since at least
commit 3999e5d01d ("[media] adv7180: Do implicit register paging").
That commit forgot to add the interrupt page number to the register
defines.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The adv7511 will automatically fill in the VIC code in the AVI InfoFrame
based on the timings of the incoming pixelport signals.
However, to have this work correctly it needs to specify the fps
value in a register. After doing this the proper VIC code is filled in.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Correctly set the h/vsync polarities instead of keeping to the
default (positive).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a number of bugs that appeared when support for mediabus formats was
added:
- Support for V4L2_DV_RGB_RANGE_FULL/LIMITED should only be enabled
for HDMI RGB formats, not for YCbCr formats. Since, as the name
says, this setting is for RGB only. So read the InfoFrame to check
the format.
- the quantization range for the pixelport depends on whether the
mediabus code is RGB or not: if it is RGB, then produce full range
RGB values, otherwise produce limited range YCbCr values.
This means that the op_656_range and alt_data_sat fields of the
platform data are no longer used and these will be removed in a
following patch.
- when setting up a new format the RGB quantization range settings
were never updated. Do so, since this depends on the format.
- fix the log_status output which was confusing and incorrect.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 1fb69bfd29 (adv7511: improve
colorspace handling) introduced a number of bugs, specifically with
regards to YCbCr output and quantization range handling:
- if the output is not RGB, then disable the full-to-limited range
CSC matrix since that is meant for RGB formats. YCbCr formats are
always limited range, so there is nothing to convert. (OK, full
range YCbCr is possible, but we don't support that right now).
- the mediabus code that was passed to adv7511_set_fmt was always cleared
by the memset in adv7511_fill_format. This made it effectively impossible
to select YCbCr output.
- adv7511_set_fmt never updated the rgb quantization range.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The IT Content bit has nothing to do with CE vs IT timings.
Delete this code. This will also fix a bug where this could
override the 'content type' control, which is actually the
correct place to set/clear the ITC bit.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Nobody is using these ops anymore, so remove these callbacks from
the subdev drivers that still have them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The part can be reset by a low pulse on the RESET pin (i.e. a hardware
reset) with a minimum width of 5 ms. It is recommended to wait 5 ms
after the low pulse before an I2C write is performed to the part.
For safety reasons, the delays will be between 5 and 10 ms.
The RESET pin can be tied high, so the GPIO is optional.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in adv76xx_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in tc358743_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_queues" enables hotplugging.
It has a single work item(&state->delayed_work_enable_hotplug) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been sync cancelled in adv7842_remove() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7511 driver.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[k.debski@samsung.com: Merged changes from CEC Updates commit by Hans Verkuil]
Signed-off-by: Kamil Debski <kamil@wypas.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7842 driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support to the adv7604 driver.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[k.debski@samsung.com: Merged changes from CEC Updates commit by Hans Verkuil]
[k.debski@samsung.com: add missing methods cec/io_write_and_or]
[k.debski@samsung.com: change adv7604 to adv76xx in added functions]
[hansverk@cisco.com: use _clr_set instead of _and_or]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The dv_timings_cap() and enum_dv_timings() pad operations take a pad
number as an input argument and return the DV timings capabilities and
list of supported DV timings for that pad.
Commit bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings
helpers") broke this as it started ignoring the pad number, always
returning the information associated with the currently selected input.
Fix it.
Fixes: bd3e275f3e ("[media] media: i2c: adv7604: Use v4l2-dv-timings helpers")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds V4L2 controls for Auto Exposure Control and Auto Gain
Control settings. These settings include low pass filter, update
frequency of these settings and the update interval for those units.
[Avoid forward declarations]
[Fix 80 columns limit violation]
[Rename controls to avoid underscores in names]
[Fix the AEC maximum shutter width on MT9V032]
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The power_on function of the driver resets the chip and sets the
CHIP_CONTROL register to 0. This switches the operating mode to slave.
The s_stream function sets the correct mode. But this caused problems on
a board where the camera chip is operated as master. The camera started
after a random amount of time streaming an image, I observed between 10
and 300 seconds.
The STRFM_OUT and STLN_OUT pins are not connected on this board which
may cause some issues in slave mode. I could not find any documentation
about this.
Keeping the chip in master mode after the reset helped to fix this
issue for me.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_WORD_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the driver fails to reset the camera or to set up control handlers, it
has to power the camera back off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This v4l2_subdev_internal_ops structure is never modified. All other
v4l2_subdev_internal_ops structures are declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The value is not used after the assignment.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/i2c/adv7842.c:2400:27: warning: 'prim_mode_txt' defined but not used [-Wunused-const-variable=]
static const char * const prim_mode_txt[] = {
^~~~~~~~~~~~~
That seems to be useful for debug, and likely were used before.
While we could simply remove, let's comment it out, for now.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tvp5150_write() function can fail so don't return 0 unconditionally
in tvp5150_s_register() but propagate what's returned by tvp5150_write().
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tvp5150_write() function calls i2c_smbus_write_byte_data() that
can fail but does not propagate the error to the caller. Instead it
just prints a debug, so callers can't know if the operation failed.
So change the function to return the error code to the caller so it
knows that the write failed and also print an error instead of just
printing a debug information.
While being there remove the inline keyword from tvp5150_write() to
make it consistent with tvp5150_read() and also because it's called
in a lot of places, so making inline is in fact counter productive
since it makes the kernel image size to be much bigger (~16 KiB).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The extraneous assignment on bt is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It's been reported that CJC7113 devices are returning
all 1s when reading register 0:
"1111111111111111" found @ 0x4a (stk1160)
This new device is apparently compatible with SA7113, so let's
add a quirk to allow its autodetection. Given there isn't
any known differences with SAA7113, this commit does not
introduces a new saa711x_model value.
Reported-by: Philippe Desrochers <desrochers.philippe@gmail.com>
Signed-off-by: Kevin Fitch <kfitch42@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some sensors (like the one in Nokia N900) provide metadata in the first
couple of lines. Make that information information available to the
pipeline.
Use u16 instead, this is a 16-bit value.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The devm_gpiod_get() function returns either a valid pointer to
struct gpio_desc or ERR_PTR() error value, check for NULL is bogus.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add entries for all supported chip variants into the of_match list, so that
the matching driver_info can be selected when using dt.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Marking these controls as private seemed a good idea at one time,
but in practice it makes no sense. So drop this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The control in question is not a private control, so drop that
comment. Copy-and-paste left-over.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 attempts to autodetect the standard. Unfortunately this
is seriously broken.
This patch removes the autodetect completely. Only the querystd op
will detect the standard. Since the design of the adv7180 requires
that you switch to a special autodetect mode you cannot call querystd
when you are streaming.
So the s_stream op has been added so we know whether we are streaming
or not, and if we are, then querystd returns EBUSY.
After testing this with a signal generator is became obvious that
a sleep is needed between changing the standard to autodetect and
reading the status. So the autodetect can never have worked well.
The s_std call now just sets the new standard without any querying.
If the driver supports the interrupt, then when it detects a standard
change it will signal that by sending the V4L2_EVENT_SOURCE_CHANGE
event.
With these changes this driver now behaves like all other video
receivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ADV7180 supports NTSC, PAL and SECAM.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the pixel aspect ratio depending on the current
standard (50 vs 60 Hz).
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the standard to the adv7180 driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch complains that there are some paths where "status" isn't
initialized. The code does assume that m5mols_read_u8() can fail so it
seems as if Smatch is correct.
Let's initialize it to REG_ISO_AUTO which is zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to import the changes at media.h, as we have a
followup patch that depends on it.
* v4l_for_linus:
[media] media.h: use hex values for range offsets, move connectors base up.
[media] adv7604: fix tx 5v detect regression
smatch complains about non-ascii characters. It turns out that a wide-dash character
was used instead of the more common '-' character.
Replace those dashes with -.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present.
The adv7511 however still reported the EDID present after disconnecting
the HDMI cable. Fix the logic regarding this control. And when the EDID
is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver.
This was also missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some macros were changed/removed at the material for v4.5. We need
to sync with those changes here, in order to avoid troubles.
* v4l_for_linus:
[media] media.h: get rid of MEDIA_ENT_F_CONN_TEST
[media] [for,v4.5] media.h: increase the spacing between function ranges
[media] media: i2c/adp1653: probe: fix erroneous return value
[media] media: davinci_vpfe: fix missing unlock on error in vpfe_prepare_pipeline()
MEDIA_ENT_F_CONN_TEST is not really a connector, it is actually
a signal generator. Also, as other drivers use the
V4L2_CID_TEST_PATTERN control for signal generators, let's change
the driver accordingly.
Tested with Terratec Grabster AV350.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tvp5150 decoder has different input connectors. The actual list of
HW inputs depends on the device version but all have at least these 3:
1) Composite0
2) Composite1
3) S-Video
and some variants have a 4th possible input connector:
4) Signal generator
The driver currently uses the .s_routing callback to switch the input
connector but since these are separate HW blocks, it's better to use
media entities to represent the input connectors and their source pads
linked with the decoder's sink pad.
This allows user-space to use the MEDIA_IOC_SETUP_LINK ioctl to choose
the input connector. For example using the media-ctl user-space tool:
$ media-ctl -r -l '"Composite0":0->"tvp5150 1-005c":0[1]'
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a header file for the tvp5150 input connectors constants that
can be shared between the driver and Device Tree source files.
[mchehab@osg.samsung.com: rename tvp5150.h also at em28xx-cards.c]
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not all tvp5150 variants support the same, for example some have an
internal signal generator that can output a black screen.
So the device id and rom version have to be stored in the driver's
state to know what variant is a given device.
While being there, remove some redundant comments about the device
version since there is already calls to v4l2_info() with that info.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the parallel mbus configuration is not correct, the endpoint
device node isn't currently put again in the error path. Fix it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This transmitter now supports configuring the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This receiver now supports reading the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This receiver now supports reading the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the helper to enumerate and set DV timings instead of a custom code.
This will ease debugging too, as it is consistent with other drivers.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Auto-gain and auto-exposure clusters in the ov9650 driver have both a
size of 2, not 3 controls. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adp1653_probe() function may return positive value EINVAL
which is obviously wrong.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWt9V+AAoJEHm+PkMAQRiGvqUH/iKVFxRB+MpfwRteRv22gfxJ
8Y5jDuCt2qkePHieN5JoY4FqWIA+hR+UnctHBvOCLC7DNbY79yaYuWeuShfnRVw2
91Kspk2tgnWkjlZDZ273VNKAEveFYUdhHvHFUlItWubVIlzrKRGKdAcUpecQ33YD
IERr4VFxdQDgksGPzH2FLJwcAKilWWygQ9ATTsY0xJepTC6PwxAFxrNx5qPiqOoI
aHJBzczk50y9hHEPkYeeWloyzIZUmf81BCi/VwOsbB30q4ENwkS2MMnebhOmBjLp
g9Bml8m/Fk4N+h2vbcLj6Bu+rE+bYDZDZ2Fmbupy4NbEkng3x3iaTPkG+R2hErQ=
=IdcS
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rc3' into patchwork
Linux 4.5-rc3
* tag 'v4.5-rc3': (644 commits)
Linux 4.5-rc3
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
...
A recent patch broke the msp3400 driver when CONFIG_MEDIA_CONTROLLER
is not set:
drivers/media/i2c/msp3400-driver.h:107:5: error: "CONFIG_MEDIA_CONTROLLER" is not defined [-Werror=undef]
It was clearly a typo, and this patch changes the
"#if CONFIG_MEDIA_CONTROLLER" to a working IS_ENABLED() check.
Fixes: fb49328217 ("[media] msp3400: initialize MC data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a partial revert of commit ed8d1cf07c ("[media] Export I2C
module alias information in missing drivers") that exported the module
aliases for the I2C drivers that were missing to make autoload to work.
But there is a bug report [0] that auto load of the ir-kbd-i2c driver
cause the Hauppauge HD-PVR driver to not behave correctly.
This is a hdpvr latent bug that was just exposed by ir-kbd-i2c module
autoloading working and will also happen if the I2C driver is built-in
or a user calls modprobe to load the module and register the driver.
But there is a regression experimented by users so until the real bug
is fixed, let's not export the module alias for the ir-kbd-i2c driver
even when this just masks the actual issue.
[0]: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=810726
Fixes: ed8d1cf07c ("[media] Export I2C module alias information in missing drivers")
Cc: <stable@vger.kernel.org> # 4.3+
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Clang complains about an extraneous definition of the module
device table after the patch to add it was accidentally merged
twice:
../drivers/media/i2c/s5c73m3/s5c73m3-spi.c:40:1: error: redefinition of
'__mod_of__s5c73m3_spi_ids_device_table'
MODULE_DEVICE_TABLE(of, s5c73m3_spi_ids);
^
../include/linux/module.h:223:27: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern const typeof(name) __mod_##type##__##name##_device_table \
^
<scratch space>:99:1: note: expanded from here
__mod_of__s5c73m3_spi_ids_device_table
This removes the second definition.
Fixes: f934a94bb5 ("[media] s5c73m3: Export OF module alias information")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_wr() is called from ops and the interrupt service routine, while
state->wr_data is shared and unprotected, and could be overwritten.
This shared buffer is therefore replaced with a local array with fixed
size. The array has the size of one EDID block (128 bytes) + 2 bytes
i2c address, and the EDID is written block by block (up to 8 blocks).
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The intent was to return -1 on error and that's what the callers expect
but the current code returns USHRT_MAX instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The saa7115 driver is used on several em28xx-based devices.
Now that we're about to add MC support to em28xx, we need to
be sure that the saa711x demod will be properly mapped at MC.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tvp5150 is an analog TV decoder. Identify as such at
the media graph, or otherwise devices using it would fail.
That avoids the following warning:
[ 1546.669139] usb 2-3.3: Entity type for entity tvp5150 5-005c was not initialized!
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tvp5150 doesn't have just one pad. It has 3 ones:
- IF input
- Video output
- VBI output
Fix it and use the macros for the pad indexes.
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch enables the tvp5150 decoder driver to be used with the media
controller framework by adding pad-level subdev operations and init the
media entity pad.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
The tvp5150 output video is interlaced so mark the format
field as alternate and reduce the height to the half.
[javier: split patch and write commit message]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
This patch were a workaround for a regression at tvp5150, but
it causes troubles on devices with omap3+tvp5151 when working
in non-parallel bus mode.
Now that em28xx was fixed, we can get rid of that.
This reverts commit 47de9bf893.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ov2659 driver performs device detection and initialization in the
following way:
- send reset command REG_SOFTWARE_RESET
- load array of predefined register's setting (~150 values)
- read device version REG_SC_CHIP_ID_H/REG_SC_CHIP_ID_L
- check version and exit if invalid.
As result, for not connected device there will be >~150 i2c transactions
executed before device version checking and exit (there are no
failures detected because ov2659 declared as I2C_CLIENT_SCCB and NACKs
are ignored in this case).
Let's fix that by checking the chip version first and start
initialization only if it's supported.
Cc: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add optional reset and standby gpios. The reset gpio is used to reset
the chip in power_on().
The standby gpio is not used currently. It is just unset, so the chip is
not in standby.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
changeset 460b6c0831 ("tvp5150: Add s_stream subdev operation
support") broke for em28xx-based devices with uses tvp5150. On those
devices, touching the TVP5150_MISC_CTL register causes em28xx to stop
streaming.
I suspect that it uses the 27 MHz clock provided by tvp5150 to feed
em28xx. So, change the logic to do nothing on s_stream if the tvp5150 is
not set up to work with V4L2_MBUS_PARALLEL.
Tested with Hauppauge WinTV USB 2 model 42012 Rev. C186
(USB ID: 2040:4200).
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Documentation/devicetree/bindings/media/i2c/tvp5150.txt DT binding doc
lists "ti,tvp5150" as the device compatible string but the driver does not
have an OF match table. Add the table to the driver so the I2C core can do
an OF style match.
Signed-off-by: Eduard Gavin <egavinc@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video decoder supports either 8-bit 4:2:2 YUV with discrete syncs
or 8-bit ITU-R BT.656 with embedded syncs output format but currently
BT.656 it's always reported. Allow to configure the format to use via
either platform data or a device tree definition.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After power-up, the tvp5150 decoder is in a unknown state until the
RESETB pin is driven LOW which reset all the registers and restarts
the chip's internal state machine.
The init sequence has some timing constraints and the RESETB signal
can only be used if the PDN (Power-down) pin is first released.
So, the initialization sequence is as follows:
1- PDN (active-low) is driven HIGH so the chip is power-up
2- A 20 ms delay is needed before sending a RESETB (active-low) signal.
3- The RESETB pulse duration is 500 ns.
4- A 200 us delay is needed for the I2C client to be active after reset.
This patch used as a reference the logic in the IGEPv2 board file from
the ISEE 2.6.37 vendor tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the .g_mbus_config subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the .s_stream subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the V4L2_CID_PIXEL_RATE control.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Expand the version detection code to identity the tvp5151.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the version detection code to a separate function and restructure
it to prepare for TVP5151 support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
VIDIOC_SUBDEV_G_FMT ioctl should return TRY format previously
set with VIDIOC_SUBDEV_S_FMT. Currently it is not the case as
only ACTIVE formats are saved in the driver. Since the driver
doesn't alter hardware state in the set_fmt op anyway, the
op can save the format in both TRY and ACTIVE case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_subdev_sensor_ops structures are never modified, so declare them
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver creates two subdevs, one for the image sensor pixel array
(and the related readout logic) and one for an ISP.
The first subdev already uses the MEDIA_ENT_T_V4L2_SUBDEV_SENSOR type,
but the second subdev isn't a sensor pixel array.
So, rename the second subdev as MEDIA_ENT_T_V4L2_SUBDEV_UNKNOWN.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This sensor driver is abusing MEDIA_ENT_T_V4L2_SUBDEV, creating
some subdevs with a non-existing type.
As this is a sensor driver, one of the entries is
MEDIA_ENT_T_CAM_SENSOR. The other one will be using
MEDIA_ENT_T_V4L2_SUBDEV_UNKNOWN, because the subdev is not
any of the already existing types.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The smiapp driver creates the pads links before the media entity is
registered with the media device. This doesn't work now that object
IDs are used to create links so the media_device has to be set.
Move entity registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the new API, a link can be either between two PADs or between an interface
and an entity. So, we need to use a better name for the function that create
links between two pads.
So, rename the such function to media_create_pad_link().
No functional changes.
This patch was created via this shell script:
for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f) $(find include/ -name '*.h' -type f) ; do sed s,media_entity_create_link,media_create_pad_link,g <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add simple support for this 8 channel volume control driver.
Currently all it does is to unmute all 8 channels.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is necessary since the *_std_setup functions rely on a valid state->std
field.
Also fix the cx23888_std_setup() to test for 60Hz instead of NTSC, just like
cx25840_std_setup() does.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For those two devices the code wrote to addresses 0x115/6, but on
those devices those addresses have nothing to do with power controls.
So clearly this never worked. Rather than writing to bogus addresses,
just do nothing for the cx2388x and cx231xx.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 reports a slightly different Vsrc value than the other
chip variants do. Relax the check by 1, otherwise cx25840_set_fmt()
would fail for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 also moves the following registers around:
!cx23888 cx23888
-------- -------
0x418, 0x41c 0x434, 0x438
0x420 0x418 (expect for bit 29 which has a different meaning)
0x478 0x454
Also drop the set_input code where the scaler is changed: this does not
belong here, changing the input should not change the scaler.
And that's besides the fact that that code is plain wrong.
After this change the cx23888 behaves much better. In particular, calling
set_input no longer changes the saturation to 0, causing a grayscale
image.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 has the VBI registers at different addresses compared to
the other variants. In most cases it is a fixed offset, but not always.
Update the code so the right registers are written for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the new match_reduced_fps argument to v4l2_match_dv_timings().
Depending on the situation you may or may not desire to match the
reduced_fps flag. Typically only HDMI transmitters will need to
check for this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit f934a94bb5 ('s5c73m3: Export OF
module alias information') broke compilation when compiled as module:
In file included from drivers/media/i2c/s5c73m3/s5c73m3-spi.c:22:0:
drivers/media/i2c/s5c73m3/s5c73m3-spi.c:40:40: error: expected ')' before ';' token
MODULE_DEVICE_TABLE(of, s5c73m3_spi_ids;);
^
Fix it by removing the extra ';'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).
So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and SPI id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same SPI device name for example.
To avoid the above, the SPI core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These v4l2_ctrl_ops structures are never modified, like all the other
v4l2_ctrl_ops structures, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Initialization of the ADV7180 chip fails on the Renesas R8A7790-based
Lager board about 50% of the time. This patch resolves the issue by
increasing the minimum delay after reset from 2 ms to 5 ms, following the
recommendation in the ADV7180 datasheet:
"Executing a software reset takes approximately 2 ms. However, it is
recommended to wait 5 ms before any further I2C writes are performed."
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The quantization bits are in bits 7-6, not 7-4, so shift by 6 instead of 4.
This bug is caused by a typo in the adv7511 datasheet.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's not mix headers used by the core with those headers that
are needed by some driver-specific interface header.
The headers used on drivers were manually moved using:
mkdir include/media/drv-intf/
git mv include/media/cx2341x.h include/media/cx25840.h \
include/media/exynos-fimc.h include/media/msp3400.h \
include/media/s3c_camif.h include/media/saa7146.h \
include/media/saa7146_vv.h include/media/sh_mobile_ceu.h \
include/media/sh_mobile_csi2.h include/media/sh_vou.h \
include/media/si476x.h include/media/soc_mediabus.h \
include/media/tea575x.h include/media/drv-intf/
And the references for those headers were corrected using:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="drv-intf/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/ml86v7667.c:430:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow the subdevice to be probed asynchronously.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).
So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and SPI id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same SPI device name for example.
To avoid the above, the SPI core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver was written with the 'soc_camera' use in mind, however the g_std()
video method was forgotten. Implement it at last...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
drivers/media/i2c/tc358743.c:1960:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hardware interrupts are enabled in the probe function, before the subdev
is registered to its v4l2_device. Until v4l2_device_register_subdev_node
is called, sd->devnode is NULL and v4l2_subdev_notify_event must not be
called.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by Randy:
> when CONFIG_MEDIA_CONTROLLER is not enabled:
>
> ../drivers/media/i2c/tc358743.c: In function 'tc358743_probe':
> ../drivers/media/i2c/tc358743.c:1890:29: error: 'struct v4l2_subdev' has no member named 'entity'
> err = media_entity_init(&sd->entity, 1, &state->pad, 0);
> ^
> ../drivers/media/i2c/tc358743.c:1940:26: error: 'struct v4l2_subdev' has no member named 'entity'
> media_entity_cleanup(&sd->entity);
> ^
> ../drivers/media/i2c/tc358743.c: In function 'tc358743_remove':
> ../drivers/media/i2c/tc358743.c:1955:26: error: 'struct v4l2_subdev' has no member named 'entity'
> media_entity_cleanup(&sd->entity);
> ^
This driver depends on VIDEO_V4L2_SUBDEV_API and needs to select HDMI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2561482468 ("[media] tc358743: support probe from device tree")
specified in the device tree binding documentation that the reset gpio
is optional. Make the implementation match accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2561482468 ("[media] tc358743: support probe from device tree")
failed to explicitly set the direction of the reset gpio. Use the
optional flag of devm_gpiod_get to make up leeway.
This is also necessary because the flag parameter will become mandatory
soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Header claims GPL v2, so make the MODULE_LICENSE reflect that properly.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
sr030pc30_get_fmt() can only succeed if both info->curr_win and
info->curr_fmt are not NULL.
If one of those vars are null, the curent code would call:
ret = sr030pc30_set_params(sd);
If the curr_win is null, it will return -EINVAL, as it would be
expected. However, if curr_fmt is NULL, the function won't
set it.
The code will then try to read from it:
mf->code = info->curr_fmt->code;
mf->colorspace = info->curr_fmt->colorspace;
with obviouly won't work.
This got reported by smatch:
drivers/media/i2c/sr030pc30.c:505 sr030pc30_get_fmt() error: we previously assumed 'info->curr_win' could be null (see line 499)
drivers/media/i2c/sr030pc30.c:507 sr030pc30_get_fmt() error: we previously assumed 'info->curr_fmt' could be null (see line 499)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Why to store the chosed values for prediv, postdiv and mult if
those won't be used?
drivers/media/i2c/ov2659.c: In function 'ov2659_pll_calc_params':
drivers/media/i2c/ov2659.c:912:35: warning: variable 's_mult' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:20: warning: variable 's_postdiv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:6: warning: variable 's_prediv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
This is likely some leftover from some past change.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/tc358743.c:148:19: warning: Variable length array is used.
As the maximum size is 1026, we can't use dynamic var, as it
would otherwise spend 1056 bytes of the stack at i2c_wr() function.
So, allocate a buffer with the allowed maximum size together with
the state var.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the i2c devices menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.
Without this, many drivers stay disabled during e.g. allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/mt9v032.c: In function ‘mt9v032_probe’:
CC [M] drivers/media/i2c/s5k4ecgx.o
drivers/media/i2c/mt9v032.c:996:20: warning: ‘pdata’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (pdata && pdata->link_freqs) {
^
It can indeed be uninitialized in one corner case. Initialize to NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using adv7611_read_cable_det() for ADV7612 means that full
support for '.max_port = ADV7604_PAD_HDMI_PORT_B,' isn't available
due to the need for multiple port reads to determine cable detection,
and an agreed mechanism for communicating the separate statuses.
This patch replaces adv7611_read_cable_det() with a functionally
identical copy, commented appropriately.
Earlier submissions [leading to commit 8331d30b] also set .cp_csc,
which is used in a cp_read() call within adv76xx_log_status().
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prior to commit f862f57d ("[media] media: i2c: ADV7604: Migrate to
regmap"), the local variable 'val' contained the combined register
reads used in the chipset version ID test. Restore this expectation
so that the comparison works as it used to.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The JPEG colorspace should only be used for JPEG encoded images. This is
just a regular sRGB sensor.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify confusing conditions. This also swaps the checks for NTSC and PAL:
to be consistent with other drivers check for NTSC first. So if the user
sets both NTSC and PAL bits, then NTSC wins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the standard changes the VACTIVE and VDELAY values need to be updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is an SDTV video receiver, so the colorspace should be SMPTE170M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The zoran driver has now been converted to the control framework
which means that these three subdevice drivers no longer need to
support the legacy core control ops since the last bridge driver
that needed that has now been converted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bt pointer was never used, remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is useful to subscribe to HDMI hotplug events via the
V4L2_CID_DV_RX_POWER_PRESENT control.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When probed from device tree, the i2c client driver can handle the interrupt
on its own.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for probing the TC358743 subdevice from device tree.
The reference clock must be supplied using the common clock bindings.
MIPI CSI-2 specific properties are parsed from the OF graph endpoint
node and support for a non-continuous MIPI CSI-2 clock is added.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add V4L2_SUBDEV_FL_HAS_DEVNODE to subdev flags, in order to
enable a subdev device node.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for registering the sensor subdevice using the v4l2-async API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver is tested on our hardware and all the implemented features
works as expected.
Missing features:
- CEC support
- HDCP repeater support
- IR support
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
[hans.verkuil@cisco.com: updated copyright year to 2015]
[hans.verkuil@cisco.com: update confusing confctl_mutex comment]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of VIDEO_ADV7604 and VIDEO_COBALT (the latter
selects the former) on GPIOLIB if COMPILE_TEST is enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow userspace applications to subscribe to control change events. This
can e.g. be used to monitor the 5V detect control to be notified when a
source is connected or disconnected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow userspace applications to subscribe to control change events. This
can e.g. be used to monitor the 5V detect control to be notified when a
source is connected or disconnected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds support to the adv7604 driver for specifying the default input
port in the Device tree. If no value is provided, the driver will be
unable to select an input without help from userspace.
Tested-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the ADV7612 chip as implemented on Renesas' Lager
board to adv7604.c, including lists for formats/colourspace/timing
selection and an IRQ handler.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix merge conflicts due to regmap patch]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a preliminary patch in order to add support for ALSA.
It replaces all current i2c access with regmap.
Signed-off-by: Pablo Anton <pablo.anton@veo-labs.com>
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a proper of match id for use when the device is being bound via
device tree, to avoid having to use the i2c old-style binding of the
device.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: William.Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
They are no longer used in old non-control-framework
bridge drivers.
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Added support for reduced blanking version 2 (RB v2) in cvt timings.
Standard specifies a fixed vsync pulse of 8 lines to indicate RB v2
timings. Vertical back porch is fixed at 6 lines and vertical front
porch is remainder of vertical blanking time.
For RB v2, horizontal blanking is fixed at 80 pixels. Horizontal sync
is fixed at 32. All horizontal timing counts (active pixels, front,
back porches) can be specified upto a precision of 1.
RB v2 allows for non standard aspect ratios. In RB v2 vsync does not
indicate aspect ratio. In absence of aspect ratio v4l2_detect_cvt()
cannot calculate image width from image height. Hence extending the
v4l2_detect_cvt() to pass image width in case of RB v2.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without setting the direction of a gpio to output a call to
gpiod_set_value doesn't have a defined outcome.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
In little endian cases, macro cpu_to_be16 unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_cpu_to_be16 and cpu_to_be16 expand directly to the
same expression. So, replace __constant_cpu_to_be16 with
cpu_to_be16 with the goal of getting rid of the definition of
__constant_cpu_to_be16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_be16(x)
+ cpu_to_be16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The subdev API is optional. No driver should depend on it.
Avoid compilation breakages if subdev API is not selected:
drivers/media/i2c/ov2659.c: In function ‘ov2659_get_fmt’:
drivers/media/i2c/ov2659.c:1054:3: error: implicit declaration of function ‘v4l2_subdev_get_try_format’ [-Werror=implicit-function-declaration]
mf = v4l2_subdev_get_try_format(sd, cfg, 0);
^
drivers/media/i2c/ov2659.c:1054:6: warning: assignment makes pointer from integer without a cast
mf = v4l2_subdev_get_try_format(sd, cfg, 0);
^
drivers/media/i2c/ov2659.c: In function ‘ov2659_set_fmt’:
drivers/media/i2c/ov2659.c:1129:6: warning: assignment makes pointer from integer without a cast
mf = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
^
drivers/media/i2c/ov2659.c: In function ‘ov2659_open’:
drivers/media/i2c/ov2659.c:1264:38: error: ‘struct v4l2_subdev_fh’ has no member named ‘pad’
v4l2_subdev_get_try_format(sd, fh->pad, 0);
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Extend detect_cvt/gtf API to indicate the format type (interlaced
or progressive). In case of interlaced, the vertical front and back
porch and vsync values for both (odd,even) fields are considered to
derive image height. Populated vsync, vertical front, back porch
values in bt timing structure for even and odd fields and updated
the flags appropriately.
Also modified the functions calling the detect_cvt/gtf(). As of now
these functions are calling detect_cvt/gtf() with interlaced flag
set to false.
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Log the alternate gamma state and the HDMI colorspace that the adv
device detected.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logging of the saturator status was wrong due to an incorrect
condition.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for logging the detected InfoFrames for the adv76xx. Helps in
debugging what is actually received on the HDMI link.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7511 sets up InfoFrames that are used when transmitting video.
Log the contents of those InfoFrames so it is possible to see exactly what
the transmitter is sending.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently this driver mixes u8/u32 and uint8_t/uint32_t. Standardize on
u8/u32.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently this driver mixes u8/u16 and uint8_t/uint16_t. Standardize on
u8/u16.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Still preliminary, but the information is at least there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7604 driver depends on GPIOLIB, and therefore cobalt depends
on it as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes it easier for the bridge driver to just passthrough such
events to the corresponding device node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Copied from the adv7604 driver.
Note: while arch/blackfin/mach-bf609/boards/ezkit.c uses adv7842_platform_data
this source has not been updated because it is broken since the very
beginning. It depends on a struct adv7842_output_format that does not
exist.
And besides that gcc has no support for bf609 so nobody can compile it
except by installing a toolchain from ADI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of parsing the link-frequencies property in the driver, let
v4l2_of_alloc_parse_endpoint() do it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
[mchehab@osg.samsung.com: fix a merge conflict at adv7604.c]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Bellow is yelling. Ok, sometimes the code is yells a lot, but
but this is not the case there ;)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The try_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Since try_mbus_fmt and s_mbus_fmt both map to the set_fmt pad op (but
with a different 'which' argument), this patch will replace both
try_mbus_fmt and s_mbus_fmt by set_fmt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The g_mbus_fmt video op is a duplicate of the pad op. Replace all uses
by the get_fmt pad op and remove the video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to the enum_mbus_fmt video op by the pad
enum_mbus_code op and remove the duplicate video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even though the format is Y'CbCr, the colorspace used by the sensor
is almost certainly SRGB. The sensor is also not generating JPEG data,
so it makes no sense to use V4L2_COLORSPACE_JPEG here.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The width and height should be checked in the enum_frame_interval
op. This fixes a v4l2-compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This needs to be signed or there is a risk of hitting a forever loop.
Fixes: c4c0283ab3 ('[media] media: i2c: add support for omnivision's ov2659 sensor')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All masks for timings are different between ADV7604 and ADV7611.
Most of the values have 1 precision bit more in the latter.
Fix this by adding new fields to the chip_info structure.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ov7670_s_exp() checks read error for 2 registers: REG_COM1
and REG_COM8. But, although it uses the value latter, it
doesn't check errors on REG_AECHH read. Yet, as it is doing
a bitmask operation there, the read operation should succeed.
So, fix the code to also check if this succeeded.
This fixes this smatch report:
drivers/media/i2c/ov7670.c:1366 ov7670_s_exp() warn: inconsistent indenting
Compile-tested only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/i2c/saa717x.c:155 saa717x_read() warn: mask and shift to zero
drivers/media/i2c/saa717x.c:155 saa717x_read() warn: mask and shift to zero
This is done right at saa717x_write(), but the read function is
broken. Thankfully, there's just one place at saa717x driver that
uses multibyte read (for status report, via printk).
Yet, let's fix it. From saa717x_write(), it is clear that the
bytes are in little endian:
mm1[4] = (value >> 16) & 0xff;
mm1[3] = (value >> 8) & 0xff;
mm1[2] = value & 0xff;
So, the same order should be valid for read too.
Compile-tested only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix these compiler warnings that appeared after switching to gcc-5.1.0:
drivers/media/i2c/s5k5baf.c: In function 's5k5baf_set_power':
drivers/media/i2c/s5k5baf.c:1057:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on != state->power)
^
drivers/media/i2c/s5k6aa.c: In function 's5k6aa_set_power':
drivers/media/i2c/s5k6aa.c:878:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == s5k6aa->power) {
^
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function 's5c73m3_oif_set_power':
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1456:17: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
} else if (!on == state->power) {
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree support for adp1653 flash LED driver.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of parsing the link-frequencies property in the driver, let
v4l2_of_alloc_parse_endpoint() do it.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As requested by Sakari:
"The driver changes are still being reviewed.
It's been proposed that the max-microamp property be renamed."
So, as the DT bindings are not agreed upstream yet, let's revert
it.
Requested-by: Sakari Ailus <sakari.ailus@iki.fi>
This reverts commit b6100f10bd.
Nokia N900 is switching to device tree, make sure we can use flash
there, too.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch add a missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't rely on V4L2_DV_BT_STD_CEA861 since that include the
640x480p format, which is an IT format, not CE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't set rval when it's not used (the function returns a pointer to struct
smiapp_platform_data).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch adds support for omnivision's ov2659
sensor, the driver supports following features:
1: Asynchronous probing
2: DT support
3: Media controller support
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The documentation stated that the link-frequencies property belongs to the
endpoint node, not to the device's of_node. Fix this.
There are no DT board descriptions using the driver yet, so a fix in the
driver is sufficient.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Parse DT properties into a platform data structure when a DT node is
available.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device requires control to be properly operated, they're not
optional.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both synchronous and asynchronous mt9p031 subdevice probing
is supported by this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure to call mutex_destroy() in case of probe failure or module
unload.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There must be used 'min_t', not 'max_t' for calculating the divider.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree support for ov2640.
In device tree, user needs to provide the master clock (xvclk).
User can add the reset/pwdn pins if they have.
Cc: devicetree@vger.kernel.org
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In async probe, there is a case that ov2640 is probed before the
host device which provided 'mclk'.
To support this async probe, we will get 'mclk' at first in the probe(),
if failed it will return -EPROBE_DEFER. That will let ov2640 wait for
the host device probed.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
pixel_order_str is only referred to in smiapp-core.c, it should be thus
static. Thanks to Hans Verkuil for pointing this out.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_property_read_u64_array() wasn't yet part of the kernel tree when the
functionality was needed. Do use it now.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_frame_interval ops. Most drivers do not
need to be changed since they always returns the same enumeration regardless
of the 'which' field.
Tested for ov7670 and marvell-ccic on a OLPC XO-1 laptop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new 'which' field in the enum_frame_size ops. Most drivers do not
need to be changed since they always returns the same enumeration regardless
of the 'which' field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If a subdevice pad op is called from a bridge driver, then there is
no v4l2_subdev_fh struct that can be passed to the subdevice. This
made it hard to use such subdevs from a bridge driver.
This patch replaces the v4l2_subdev_fh pointer by a v4l2_subdev_pad_config
pointer in the pad ops. This allows bridge drivers to use the various
try_ pad ops by creating a v4l2_subdev_pad_config struct and passing it
along to the pad op.
The v4l2_subdev_get_try_* macros had to be changed because of this, so
I also took the opportunity to use the full name of the v4l2_subdev_get_try_*
functions in the __V4L2_SUBDEV_MK_GET_TRY macro arguments: if you now do
'git grep v4l2_subdev_get_try_format' you will actually find the header
where it is defined.
One remark regarding the drivers/staging/media/davinci_vpfe patches: the
*_init_formats() functions assumed that fh could be NULL. However, that's
not true for this driver, it's always set. This is almost certainly a copy
and paste from the omap3isp driver. I've updated the code to reflect the
fact that fh is never NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify accordingly.
Moreover use devm_gpiod_get_index_optional instead of
devm_gpiod_get_index with ignoring all errors.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch drops module param 'debug' as it was never used.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers are moved to support asynchronous probing,
v4l2_async_unregister_subdev() unregisters the subdev so
there isn't a need to explicitly call v4l2_device_unregister_subdev().
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace dev_err statement with pr_err to fix null dereference.
Found by Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is confusing which parts of the driver are adv7604 specific, adv7611
specific or common for both. This patch renames any adv7604 prefixes (both
for functions and defines) to adv76xx whenever they are common.
Signed-off-by: Pablo Anton <pablo.anton@vodalys-labs.com>
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
[hans.verkuil@cisco.com: rebased and renamed ADV76xx_fsc to ADV76XX_FSC]
[hans.verkuil@cisco.com: kept the existing adv7604 driver name]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bits are the same, but register is 0xf4 on ADV7611 instead of 0xfc.
When reading back the value in log_status, differentiate both.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The CP_NON_STD_VIDEO bit indicates an input not aligned with DV timings.
If there is no input, and chip is in free run mode, consider we are locked.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
[hans.verkuil@cisco.com: put both conditions in one 'if']
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use an enum to better document the media pads.
No functional changes.
Suggested-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no need to free state, as it was allocated via devm_kzalloc().
Also, let's return the error code, instead of something else.
Reported-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Analog video inputs are the tuner, plus composite, svideo, etc,
e. g. the input pat should actually be like:
___________
TUNER --------> | |
| |
SVIDEO .......> | cx25840 |
| |
COMPOSITE1 ...> |_________|
(in the above, dashes represent the enabled link, and periods
represent the disabled ones)
In other words, if we want to properly represent the pipeline,
it should be possible to see via the media controller if the tuner
is being used as an image source, or if the source is something else.
I didn't map those other inputs here yet, due to a few things:
- The extra inputs would require subdevs that won't be controlled
- I was in doubt about the best way for doing that
- That would likely require some extra setup for cx25840 caller
drivers, in order to represent what of the possible internal
inputs are actually used on each specific board
Actually, at least for now, I was unable to see much benefit
on adding such map now, so let's just document it, as this could
be added later on, as needed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of keeping the media controller entity not initialized,
fill it and create the pads for cx25840.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In fast switch mode the adv7180 (and similar) can lock onto a new signal
faster when switching between different inputs. As a downside though it is
no longer able to auto-detect the incoming format.
The fast switch mode is exposed as a boolean v4l control that allows
userspace applications to either enable or disable fast switch mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some of the devices supported by this driver have a interlaced-to-
progressive converter which can optionally be enabled. This patch adds
support for enabling and disabling the I2P converter on such devices.
I2P mode can be enabled by selecting V4L2_FIELD_NONE instead of
V4L2_FIELD_INTERLACED for the format.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7280-m/adv2781-m/adv7281-ma/adv7282-m
devices to the adv7180 driver. They are very similar to the
adv7280/adv7281/adv7282 but instead of parallel video out they feature a
MIPI CSI2 transmitter.
The CSI2 transmitter is configured via a separate I2C address, so we need to
register a dummy device for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7280/adv7281/adv7282 devices to the
adv7180 driver. They are very similar to the adv7182, the main difference
from the drivers point of view are some different tuning constants for
improved video performance.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the adv7182 to the adv7180 driver. The adv7182
is similar to the adv7180, the main difference from the driver's point of
view is how the video input and how the input format are selected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 is part of a larger family of device, which have all a very
similar register map layout. This patch prepares the adv7180 driver for
support for multiple different devices. For now the only difference we care
about is the number of input channel configurations. Also the way the input
format is configured slightly differs between some devices.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We have basically the same code to set the video standard in init_device()
and adv7180_s_std(). Factor this out into a common helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add media controller support to the adv7180 driver by registering a media
entity instance for it as well as implementing pad ops for configuring the
format.
As there currently don't seem to be any users of the video ops format
operations those are removed as well in this patch.
Also set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so it is
possible to create a subdevice device node.
Since the driver now depends on VIDEO_V4L2_SUBDEV_API all drivers which
select the driver need to depend on that symbol as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reset the device when initializing it so it is in a good known state and the
assumed register settings matches the actual register settings.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ad7180 has multiple register pages which can be switched between by
writing to a register. Currently the driver manually switches between pages
whenever a register outside of the default register map is accessed and
switches back after it has been accessed. This is a bit tedious and also
potential source for bugs.
This patch adds two helper functions that take care of switching between
pages and reading/writing the register. The register numbers for registers
are updated to encode both the page (in the upper 8-bits) and the register
(in the lower 8-bits) numbers.
Having multiple pages means that a register access is not a single atomic
i2c_smbus_write_byte_data() or i2c_smbus_read_byte_data() call and we need
to make sure that concurrent register access does not race against each
other.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Consistently prefix register defines with ADV7180_REG. Also remove the "ADI"
from register names, the ADV7180 prefix should provide enough of a namespace
separation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most IRQ controllers support different types of interrupts. The adv7180
generates falling edge interrupts, so make sure to pass IRQF_TRIGGER_FALLING
to request_threaded_irq() so the IRQ controller is configured for the
correct mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently the IRQ is requested from within the init_device() function. This
function is not only called during device probe, but also during resume
causing the driver to try to request the IRQ again. Move requesting the IRQ
from init_device() to the probe function to make sure that it is only
requested once.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reuse the v4l2 size definitions from v4l2-image-sizes.h.
So we can remove the rudundent definitions from ov2640.c.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_read_number() is defined in of.h but does not return an error code, so
that non-of implementation could simply return an error.
Temporarily work around this until of_read_number() can be replaced by
of_property_read_u64_array().
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new logging functions from the hdmi module.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to jump to the 'err' label as we can simply return the error
code directly and make the code shorter.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
test_read() edid_read_block() dpp_write() dpp_read()
esdp_write() esdp_read() cec_write_clr_set()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removes some functions that are not used anywhere:
vblanking() hblanking()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes the macros a little bit safer.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pll_flags quirk just returned the extra PLL flags the sensor required,
but the init quirk is far more versatile. It can be used to perform any
extra initialisation needed by the sensor, including allocating memory for
sensor specific struct and creating sensor specific new controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As the controls creation is separated in two sections, the available media
bus codes and link frequencies can be enumerated later on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The default values and limits for certain controls need the knowledge of
available media bus codes or link frequencies. Create such controls later
on, so that most of the initialisation of the sensor has already been done
when the init quirk is called.
[mchehab@osg.samsung.com: make checkpatch.pl happier]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clean up smiapp_init_controls() by adding newlines to appropriate places and
by removing superfluous error handling. The caller will clean up control
handlers in any case if the function fails.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Also call smiapp_cleanup() in smiapp_remove(), replacing code that did the
same than the function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The flash capability register is already read as part of the limit
registers. Do no access it separately; instead use the value from the
limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the case of platform data, ISPs that provide clocks to the sensor must
probe before the sensor does. Accessing the sensor does require the clocks,
and thus, probe cannot access the sensor in such a system.
This limitation does not exist in the case of the DT. Perform all
initialisation except Media entity initialisation, link creation and
sub-device registration in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The registered callback is called by the V4L2 async framework after the
bound callback. This allows separating the functionality in the registered
callback so that on DT based systems only sub-device registration is done
there.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform data support is retained.
of_property_read_u64_array() isn't used yet as it's not in yet.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SMIA compatible sensors only need a single clock.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The source sub-device's name will be overwritten shortly. Don't give it a
name in the meantime.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct device has a forward declaration in the header already. The header is
only needed in the .c file.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove FSF's address information from the license header in the smiapp
driver and the smiapp-pll PLL calculator. This should no longer be needed,
and would be rendered outdated in case the FSF chooses to relocate its
office.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Timo Ahonen <timo.ahonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:223:16: warning: cast to restricted __be16
drivers/media/i2c/s5k4ecgx.c:344:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:354:20: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:364:24: warning: cast to restricted __le32
drivers/media/i2c/s5k4ecgx.c:366:23: warning: cast to restricted __le16
The get_unaligned_le*() functions return the value using cpu endianness,
so calling le*_to_cpu is wrong.
It hasn't been not noticed because this code has only been run on little
endian systems, so le*_to_cpu doesn't do anything.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:128:24: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:130:24: warning: cast to restricted __be32
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:457:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:458:19: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:459:22: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
drivers/media/i2c/m5mols/m5mols_core.c:460:20: warning: cast to restricted __be16
The be16_to_cpu conversions in m5mols_get_version() are not needed since the
data is already using cpu endianness. This was never noticed since these
version fields are never used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These drivers depend on VIDEO_V4L2_SUBDEV_API, which in turn
depends on MEDIA_CONTROLLER. So it is sufficient to just depend
on VIDEO_V4L2_SUBDEV_API.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The crop and selection pad ops are duplicates. Replace all uses of get/set_crop
by get/set_selection. This will make it possible to drop get/set_crop
altogether.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUksm/AAoJEAhfPr2O5OEV7GIP/1nm2rcf16+6Y7nhjWLgPmlU
uG9fNUMm7qvFHryCr4RwmTBnCv63Nn/5BFRcXdpAA2gHOtADcHCDNJbtSX+GRN5F
I0C5gbLbQVd7l/GFsiGTsBScInAQB+ZN0WNyPbF0OCGLuzzRlexadAYTZufnNiNN
nYCINIBub0jUPJaIrbm/qDAbazS7fxTO9HAdMcJGtexPCO/Gj92+4s8NXI+N3hxk
Cj87EPsk6i6GA1BM0oVmDWK0dQjgFm+ONMBc8vhFOyVzCXb7pjHg53n1zZ0e0TDt
jm/h/oIJuWyH/isEuwcNPTBxf2E9EOv8g66V9mDN1i7zsTEf9Bs08fPigalfJ84x
5S5GBaHEGIu8d2PgqaqxmFO1COyk+xoj9O0Iwx8uabYtyRtgUVaEtsfyHWU2ZiAh
3wqmtHSK5mt835h9wzjxs18apnRhTwEhfQWzFdiCFxkDPz3vPmfWbm+8WHChtYJh
j0oSJwzK9uAcYwG8WZi643WduIyrXiDqaglWyBg+7c2k3NhP76W5CpLhjZ+8PrYt
I6Jf+gZL/Joq5bMQx6itajgE5IIhAfxmdyaYIBqmlXuQ/88zrw7JBwu6q22jSVbq
+QaURaSJ6qOLYj6S/ip93KPVsUXmfdE1JttuLp4ie7r0Q8zOahr4dPQ/xAwATtY/
Jeo+d7AI4tLWQcIDKIWi
=1rPM
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull second set of media updates from Mauro Carvalho Chehab:
- Move drivers for really old legacy hardware to staging. Those are
using obsolete media kAPIs and are for hardware that nobody uses for
years. Simply not worth porting them to the new kAPIs. Of course,
if anyone pops up to fix, we can move them back from there
- While not too late, do some API fixups at the new colorspace API,
added for v3.19
- Some improvements for rcar_vin driver
- Some fixups at cx88 and vivid drivers
- Some Documentation fixups
* tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] bq/c-qcam, w9966, pms: move to staging in preparation for removal
[media] tlg2300: move to staging in preparation for removal
[media] vino/saa7191: move to staging in preparation for removal
[media] MAINTAINERS: vivi -> vivid
[media] cx88: remove leftover start_video_dma() call
[media] cx88: add missing alloc_ctx support
[media] v4l2-ioctl: WARN_ON if querycap didn't fill device_caps
[media] vivid: fix CROP_BOUNDS typo for video output
[media] DocBook media: update version number and document changes
[media] vivid.txt: document new controls
[media] DocBook media: add missing ycbcr_enc and quantization fields
[media] v4l2-mediabus.h: use two __u16 instead of two __u32
[media] rcar_vin: Fix interrupt enable in progressive
[media] rcar_vin: Enable VSYNC field toggle mode
[media] rcar_vin: Add scaling support
[media] rcar_vin: Add DT support for r8a7793 and r8a7794 SoCs
[media] rcar_vin: Add YUYV capture format support
These drivers haven't been tested in a long, long time. The hardware is
ancient and hopelessly obsolete. These drivers also need to be converted
to newer media frameworks but due to the lack of hardware that's going
to be impossible.
So these drivers are a prime candidate for removal. If someone is
interested in working on these drivers to prevent their removal, then
please contact the linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
Add support for selection target V4L2_SEL_TGT_NATIVE_SIZE. It is equivalent
of what V4L2_SEL_TGT_CROP_BOUNDS used to be. Support for
V4L2_SEL_TGT_CROP_BOUNDS is still supported by the driver as a compatibility
interface.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The fields were previously uninitialised, leaving the returned values to
where the user had set them. This was never the intention.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for YCbCr output and support setting colorspace,
YCbCr encoding and quantization for the AVI InfoFrame.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The rc_unregister_device() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definitions to include/uapi/linux/media-bus-format.h and
prefixed values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Replace all references to the old definitions in i2c drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting a non-settable selection target caused BUG() to be called. The check
for valid selections only takes the selection target into account, but does
not tell whether it may be set, or only get. Fix the issue by simply
returning an error to the user.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have v4l2-compliance tool pass the G/S_EDID some modifications
where needed in the driver.
In particular, the edid.reserved zone must be blanked.
Based on a patch from Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>,
but reworked it a bit. It should use 'data' (which depends on edid.present)
instead of edid.blocks as the check whether edid data is present.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the v4l2-compliance failures.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this pass the v4l2-compliance test.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
This use has a mask then shift which is not the normal style.
Move the shift before the mask to match nearly all the other
uses in kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason to report:
cx25840 7-0044: Firmware download size changed to 16 bytes max length
If the driver needs to adjust the buffer's maximum size.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media bus format BPP does affect PLL. Recalculate PLL if the format
changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set supported link frequencies in the menu in control initialisation and
when the bpp changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
smiapp_set_format() has accumulated a fair amount of changes without a
needed refactoring, do the cleanup now. There's also an unlocked version of
v4l2_ctrl_range_changed(), using that fixes a small serialisation issue with
the user space interface.
__v4l2_ctrl_modify_range() is used instead of v4l2_ctrl_modify_range() in
smiapp_set_format_source() since the mutex is now held during the function
call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some media bus codes may be unavailable depending on the available media bus
codes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not all link rates are possible with all BPP values.
Also rearrange other initialisation a little. Obtaining possible PLL
configurations earlier requires that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The first one is handy for just trying out a PLL configuration without a
need to apply it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The actual pixel array pixel rate may be something else than vt_pix_clk_freq
on some implementations. Add a new field which contains the corrected value.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
op_pix_clk_div is directly assigned and not calculated. There's no need to
verify it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need to pretend the OP limits are there anymore.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For profile 0 sensors (which have no OP clocks), the OP limits are in fact
VT limits. Do not verify them again.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Profile 0 sensors have no OP clock branck in the clock tree. The PLL
calculator still calculated them, they just weren't used for anything.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Uniform representation for VT and OP clocks. This is preparation for
calculating the VT clocks using the OP clock code.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enough work for this function already.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These values are unsigned, so use %u instead of %d.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The PLL flags were not used correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mutex does not serialise anything in this case but avoids a lockdep
warning from the control framework.
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The log_status function should show HDMI information, but the test checking for
an HDMI input was inverted. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both adv7604 and adv7842 had the same typo in the code that sets
the vertical backporch for the second interlaced field: it was
assigned to vbackporch instead of il_vbackporch.
In addition, the timings struct wasn't zeroed in the adv7842 driver,
leaving several fields to undefined values causing the timing match
function to fail.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Test for definedness of the macro which is actually defined, and which
matches the name of the file.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ensures device->streaming has correct status.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
Instead of using if (on == true), just use
if (on).
That allows a faster mental parsing when analyzing the
code.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The smiapp driver is the owner of the sub-devices exposed by the smiapp
driver. This prevents unloading the module whilst it's in use.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor may be powered by either one of its sub-devices being accessed
from the user space (an open file handle) or by its s_power() op being
called with non-zero on argument. The driver counts the users and if any
reason to keep the device powered exists it will be powered.
However, a faulty condition was used in recognising the need to power off
the sensor, leading it to be powered off every time any of its uses went
away.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix a copy-paste bug when converting to the control framework.
Fixes: commit 5d478e0de8 ("[media] tda7432: convert to the control framework")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
So we can remove the same defines in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Using the managed function the kfree() calls can be removed from the
probe error path and the remove handler.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of modifying the control ranges directly by manipulating struct
v4l2_ctrl, use __v4l2_ctrl_modify_range() for the purpose.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the V4L2_CID_TEST_PATTERN control. When the solid colour
mode is selected, additional controls become available for setting the
solid four solid colour components.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add device-tree support for mt9m111 camera sensor.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
X-Patchwork-Delegate: mchehab@redhat.com
The driver mistakenly prints the ROM version instead of the device ID to
the kernel log when detecting the chip. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The SMIA++ sensors are progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor is progressive, always return the field order set to
V4L2_FIELD_NONE.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This switches all register accesses to use regmap. It allows to
use the regmap cache, tracing, and debug register dump facilities,
and removes the need to open code read-modify-writes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for registering the sensor subdevice using the v4l2-async API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
as are mt9v024 and mt9v034. With minimal changes it is possible
to support mt9v02[24] with the same driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The read mode register bits 8 and 9 are set and marked as reserved.
Don't clear them.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since (min_row_time - crop->width) can be negative, we have to do a signed
comparison here. Otherwise max_t casts the negative value to unsigned int
and sets min_hblank to that invalid value.
Cc: stable@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver moved over to v4l2_async_unregister_subdev()
but still retained a call to v4l2_unregister_subdev(). Remove.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da increased the internal control ranges
to 64 bit, but that caused problems in drivers that use the minimum/maximum/step/default_value
control values in a division or modulus operations since not all architectures support
those natively.
Luckily, in almost all cases it is possible to just cast to 32 bits (the control value
is known to be 32 bits, so it is safe to cast). Only in v4l2-ctrls.c was it necessary to
use do_div in one function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.
The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While VIDIOC_QUERYCTRL is limited to 32 bit min/max/step/def values
for controls, the upcoming VIDIOC_QUERY_EXT_CTRL isn't. So increase
the internal representation to 64 bits in preparation.
Because of these changes the msi3101 driver has been modified slightly
to fix a formatting issue (%d becomes %lld), vivi had to be modified
as well to cope with the new 64-bit min/max values and the PIXEL_RATE
control in a few sensor drivers required proper min/max/def values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Update the recommended writes to those mentioned in the Rev 1.5 version of the
ADV7611 Register Settings Recommendations document released by Analog Devices.
The document does not mention why the recommended settings have been updated,
but presumably those are more fine tuned settings that can enhance performance
in some cases.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The I2C address of the sensor device was in the middle of the sub-device
name and not in the end as it should have been. The smiapp sub-device names
will change from e.g. "vs6555 1-0010 pixel array" to "vs6555 pixel array
1-0010".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull updates and DT support for media engines from Mauro Carvalho Chehab.
For Analog Devices ADV7604 and the Renesas VSP1 video processing engines.
* 'topic/vsp1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: vsp1: Add DT support
[media] v4l: vsp1: Add DT bindings documentation
[media] v4l: vsp1: Add BRU support
[media] v4l: vsp1: Support multi-input entities
[media] v4l: vsp1: uds: Enable scaling of alpha layer
[media] v4l: vsp1: Remove unexisting rt clocks
* 'topic/adv76xx' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (21 commits)
[media] adv7604: Add LLC polarity configuration
[media] adv7604: Set HPD GPIO direction to output
[media] adv7604: Add endpoint properties to DT bindings
[media] adv7604: Add DT support
[media] adv7604: Specify the default input through platform data
[media] adv7604: Support hot-plug detect control through a GPIO
[media] adv7604: Sort headers alphabetically
[media] adv7604: Replace *_and_or() functions with *_clr_set()
[media] adv7604: Store I2C addresses and clients in arrays
[media] adv7604: Inline the to_sd function
[media] v4l: subdev: Remove deprecated video-level DV timings operations
[media] adv7604: Remove deprecated video-level DV timings operations
[media] adv7604: Add pad-level DV timings support
[media] adv7604: Make output format configurable through pad format operations
[media] adv7604: Add sink pads
[media] adv7604: Remove subdev control handlers
[media] adv7604: Add adv7611 support
[media] adv7604: Cache register contents when reading multiple bits
[media] adv7604: Add 16-bit read functions for CP and HDMI
[media] adv7604: Don't put info string arrays on the stack
...
The include/media/s5p_fimc.h header has been removed in commit
49b2f4c56f ("exynos4-is: Remove support
for non-dt platforms"). This broke compilation of the m5mols driver.
Include the include/media/exynos-fimc.h header instead, which contains
the S5P_FIMC_TX_END_NOTIFY definition required by the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an inv_llc_pol field to platform data to control the clock polarity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The HPD GPIO is used as an output but its direction is never set. Fix
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the hsync-active, vsync-active and pclk-sample
properties to the DT bindings and control BT.656 mode implicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Parse the device tree node to populate platform data. Only the ADV7611
is currently support with DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
And set input routing when initializing the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for optional GPIO-controlled HPD pins in addition to the
ADV7604-specific hotplug notifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The *_and_or() functions take an 'and' bitmask to be ANDed with the
register value before ORing it with th 'or' bitmask. As the functions
are used to mask and set bits selectively, this requires the caller to
invert the 'and' bitmask and is thus error prone. Replace those
functions with a *_clr_set() variant that takes a mask of bits to be
cleared instead of a mask of bits to be kept.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This allows replacing duplicate code blocks by loops over the arrays.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This one line function is called in a single location. Inline it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADV7604 has sink pads for its HDMI and analog inputs. Report them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Control operations are handled by the control framework and the subdev
control handlers are never called directly. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the Analog Devices ADV7611 HDMI receiver.
The adv7611 is quite similar to the adv7604. It has only one instead of four
HDMI inputs and no analog frontend though. Also some register bits have been
shuffled around, but large parts of their register maps are compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When extracting multiple bits from a single register read the register
once and extract the bits on the read value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
16-bit registers are read through two 8-bit read operations. Factorize
that common pattern into 16-bit read accessors to simplify the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We do not want to modify the info string arrays ever, so no need to
waste stack space for them. While we are at it also make them const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Register the device with the v4l2 asynchronous probing framework to
support asynchronous instantiation systems such as DT.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The subdev EDID ioctls receive a pad field that must reference an
existing pad and an EDID field that must point to a buffer. Validate
both fields in the core code instead of duplicating validation in all
drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated
and unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings operation is deprecated. Implement the
pad-level version of the operation to prepare for the removal of the
video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The video enum_dv_timings and dv_timings_cap operations are deprecated.
Implement the pad-level version of those operations to prepare for the
removal of the video version.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the driver-specific inline function to cast from a subdev pointer to
a tvp5150 pointer instead of the generic container_of().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Auto BLC and BLC digital offset are disabled when enabling the test
pattern and must be restored when disabling it. The driver does so by
calling the set control handler on the auto BLC and BLC offset controls,
but this programs the hardware with the new value of those controls, not
the current value. Fix this by writing to the registers directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The digital side of the Black Level Calibration (BLC) function must be
disabled when generating a test pattern to avoid artifacts in the image.
The driver disables BLC correctly at the hardware level, but the feature
gets reenabled by v4l2_ctrl_handler_setup() the next time the device is
powered on.
Fix this by marking the BLC controls as inactive when generating a test
pattern, and ignoring control set requests on inactive controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Prepare for supporting systems using the Device tree. Should the resources
not be available at the time of driver probe(), the EPROBE_DEFER error code
must be also returned from its probe function.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Do not use our special value, SMIAPP_NO_XSHUTDOWN.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The "best" value was unsigned however, leading to signed-to-unsigned
comparison and wrong results. Possibly only on a newer GCC. Fix this by
making the best value signed as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some of the limits are used before the limits quirk is called. Move the call
immediately after obtaining the limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 75e2bdad89 "ov7670: allow
configuration of image size, clock speed, and I/O method" uses a wrong
index to iterate an array. Apart from being wrong, it also uses an
unchecked value from user-space, which can cause access to unmapped
memory in the kernel, triggered by a normal desktop user with rights to
use V4L2 devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The register address, width and flags are encoded as a 32-bit value. Add
macros for obtaining these separately. Use the macros in register access
functions.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a quirk for diverting registers for on some sensors, even the standard
registers are not where they can be expected to be found. Add a quirk to
to help using such sensors.
smiapp_write_no_quirk() and smiapp_read_no_quirk() functions are provided
for the use of quirk implementations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is more flexible. Quirk flags may be affected by configuration.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No reason to keep this u8, really.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It doesn't make sense to just copy the information to the PLL flags. Add a
new fields for the quirks to contain the PLL flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sub-device names should be unique. Should two identical sensors be
present in the same media device they would be indistinguishable. The names
will change e.g. from "vs6555 pixel array" to "vs6555 1-0010 pixel array".
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
8-bit reads are needed in some cases; however the condition used was wrong.
Regular access (register width) was used if:
len == SMIAPP_REG_8BIT && !only8
This causes 8-bit read access to be used always. The operator should be ||
instead: regular access can be used for 8-bit reads OR if allowed otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SMIAPP_REG_ is the common prefix used in the driver for register related
definitions. Use it consistently.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The quirk registers mechanism which allows register to have a static read
access value from the sensor specific quirks, is not used. Remove it. It is
to be replaced by a more generic register diversion quirk soon.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In core_init make sure access to EDID DDC lines are disabled
before chip is powered up. Also DISABLE_AUTO_EDID before power up.
The correct setting is applied later when setting the EDID.
Some sources (MAC) kept on reading EDID even when Hotplug was low
and in the short period in core_init before the DDC lines was enabled
read a corrupt EDID.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This was the reason for enabling the HDMI/DVI-D mode irq in the first place.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This fixes following build error:
CC drivers/media/i2c/s5c73m3/s5c73m3-core.o
CC drivers/md/dm-ioctl.o
CC net/ipv4/inet_lro.o
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function ‘s5c73m3_get_platform_data’:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:2: error: implicit declaration of function ‘v4l2_of_get_next_endpoint’ [-Werror=implicit-function-declaration]
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1619:10: warning: assignment makes pointer from integer without a cast [enabled by default]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull exynos media updates from Mauro Carvalho Chehab:
"These are the remaining patches I have for the merge windows. It
basically adds a new sensor and adds the needed DT bits for it to
work"
* 'topic/exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] s5p-fimc: Remove reference to outdated macro
[media] s5p-jpeg: Fix broken indentation in jpeg-regs.h
[media] exynos4-is: Add the FIMC-IS ISP capture DMA driver
[media] exynos4-is: Add support for asynchronous subdevices registration
[media] exynos4-is: Add clock provider for the SCLK_CAM clock outputs
[media] exynos4-is: Use external s5k6a3 sensor driver
[media] V4L: s5c73m3: Add device tree support
[media] V4L: Add driver for s5k6a3 image sensor
[media] Documentation: devicetree: Update Samsung FIMC DT binding
[media] Documentation: dt: Add binding documentation for S5C73M3 camera
[media] Documentation: dt: Add binding documentation for S5K6A3 image sensor
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
There is request_irq() in init_device(), but the interrupt is not removed
on failure paths. The patch adds proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the V4L2 asynchronous subdev registration and
device tree support. Common clock API is used to control the
sensor master clock from within the subdev.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds subdev driver for Samsung S5K6A3 raw image sensor.
As it is intended at the moment to be used only with the Exynos
FIMC-IS (camera ISP) subsystem it is pretty minimal subdev driver.
It doesn't do any I2C communication since the sensor is controlled
by the ISP and its own firmware.
This driver, if needed, can be updated in future into a regular
subdev driver where the main CPU communicates with the sensor
directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These chips makes use of the media_entity in the v4l2_subdev struct
and is therefor dependent of the MEDIA_CONTROLLER config.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7180 has a low power mode in which the analog and the digital processing
section are shut down. Implement the s_power callback to let bridge drivers put
the part into low power mode when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for async device registration to the adv7180 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The proper way to handle IRQs that need to be able to sleep in their IRQ handler
is to use a threaded IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The device driver core already prints out a very similar message when a driver
fails to probe. No need to print one in the driver itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The device can't possibly be registered at this point, so no need to to call
v4l2_device_unregister_subdev().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make sure to free the control handler when the device is removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mutex is used in the subdev callbacks, so unregister the subdev before the
mutex is destroyed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds the driver for the LM3646, dual LED Flash driver.
The LM3646 has two 1.5A sync. boost converter with dual white current source.
It is controlled via an I2C compatible interface.
Each flash brightness, torch brightness and enable/disable can be controlled.
Under voltage, input voltage monitor and thermal threshhold Faults are added.
Please refer the datasheet http://www.ti.com/lit/ds/snvs962/snvs962.pdf
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If we have no pdata defined and driver fails to register we leak memory.
Converting to devm_kzalloc prevents this to happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Let's keep the style for all comments in the code, namely using small letters
whenever it's possible.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is no need to keep the FSF address inside each file. Moreover, it might
change in future which will make this one obsolete.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set permissions on the debug module parameter to make it appear in sysfs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch moves the parsing helpers used to parse connected graphs
in the device tree, like the video interface bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt, from
drivers/media/v4l2-core/v4l2-of.c into drivers/of/base.c.
This allows to reuse the same parser code from outside the V4L2
framework, most importantly from display drivers.
The functions v4l2_of_get_next_endpoint, v4l2_of_get_remote_port,
and v4l2_of_get_remote_port_parent are moved. They are renamed to
of_graph_get_next_endpoint, of_graph_get_remote_port, and
of_graph_get_remote_port_parent, respectively.
Since there are not that many current users yet, switch all of
them to the new functions right away.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Closer inspection on exact transmitted format showed that
we needed to add 1 on vertical sync.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
HS_IN/VS_IN was always set to positive.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently only RGB444 input data is supported so set to zero.
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the input clock frequency is out of bounds for the PLL, bypass the
PLL and just divide the input clock to achieve the requested output
frequency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor needs a master clock, handle it explictly in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor needs two power supplies, VAA and VDD. Require a regulator
for each of them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This applies to HDMI-map register 0x69.
So far we have been using HPA manual mode.
This way we had control of HPA which could be
set after EDID had been programmed.
Using a Mac Mini with mini-displayport to DVI-D converter as source
caused the adv7842 to lock up and fail to detect any further signals.
After experimenting with different configurations it was found that
using the HPA auto mode and in addition letting RX-termination
be controlled by HPA prevented this error from occuring.
I was not able to re-create this problem on the adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Clear any pending AVI checksum-errors.
To be able to display last received AVI.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Incorrect registers used for pixelclock read-out.
Same registers as for adv7604 which actually gave an almost
correct read-out, even they are not documented for adv7842.
Corrected deep-color pixel-clock correction.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Copied and adopted from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Using variable length array in s5k5baf_write_arr_seq caused
an implicit assumption that i2c sequences should be short.
The patch rewrites the function so it can handle sequences
of any length and does not use variable length array.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following error:
ERROR: return is not a function, parentheses are not required
FILE: drivers/media/i2c/s5k5baf.c:1353:
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following warnings:
drivers/media/i2c/s5k5baf.c: In function 's5k5baf_fw_parse':
drivers/media/i2c/s5k5baf.c:362:3: warning:
format '%d' expects argument of type 'int', but argument 3 has type 'size_t' [-Wformat=]
drivers/media/i2c/s5k5baf.c:383:4: warning:
format '%d' expects argument of type 'int', but argument 4 has type 'size_t' [-Wformat=]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa6588 always blocked while waiting for data, even if the filehandle
was in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
CMD_CLOSE sets data_available_for_read to 1, which is necessary to do the
wakeup call, but it is never reset to 0.
Because of this calling CMD_POLL afterwards will always return that data is
available, even if there isn't any.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver is independent from saa7134, so there is no reason why this
shouldn't be in media/i2c like all other i2c media drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a proper driver strength enum and use the same names in the platform
data as with adv7604.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Return 0 if the new timings are equal to the current timings as
it caused extra cp-loss/lock interrupts.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Must clear timings before setting after test to recover.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Clear i2c_clients ptr when unregistered.
Warn if configured i2c-addr is zero.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The STDI block may measure wrong values, especially for lcvs and lcf.
If the driver can not find any valid timing, the STDI block is restarted
to measure the video timings again. The function will return an error,
but the restart of STDI will generate a new STDI interrupt and the format
detection process will restart.
Copied from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Wait 5ms after main reset. The data-sheet doesn't specify the wait
after i2c-controlled reset, so using same value as after pin-controlled
reset.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.
In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.
This adds the possibility to change output config between the fields and standards.
This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
For edid with no Source Physical Address (spa), set
spa-location to default and use correct values from edid.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The method of disabling the irq-output pin caused many "empty"
interrupts. Instead, actually disable/enable the interrupts by
changing the interrupt masks.
Also enable STORE_MASKED_IRQ in INT1 configuration, otherwise when HDMI
events happen while the interrupt is masked those events will be ignored
when the interrupt is unmasked.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Bit 6 of register 0x8f was cleared incorrectly (must be 1), and bit 4
of register 0x91 was set incorrectly (must be 0).
These bits are undocumented, so we shouldn't modify them to values different
from what the datasheet specifies.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This simplified the code quite a bit.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some sources are initially detected as DVI, and change to HDMI later.
This must be detected to set the right RGB quantization range.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input signal is DVI-D and quantization range is RGB full range,
gain and offset must be adjusted to get the right range on the output.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the restart_stdi_once trick fails to find a valid
format the flag was never reset.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ADV7604_FMT_CHANGE events was debounced in adv7604_isr() to avoid
that a receiver with a unstable input signal would block the event
handling for other inputs. This solution was prone to errors.
A better protection agains interrupt blocking is to delay the call
of the interrupt service routine in the adv7604 driver if too many
interrupts are received within a given time.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- split edid_write_block()
- do not use edid->edid before the validity check
- Return -EINVAL if edid->pad is invalid
- Save both registers for SPA port A
- Set SPA location to default value if it is not found
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the input is ADV7604_INPUT_VGA_RGB and RGB quantization range is
set to V4L2_DV_RGB_RANGE_AUTO, video with CEA timings will be
received as RGB. For ADV7604_INPUT_VGA_COMP, automatic CSC mode
will be selected.
See table 44 on page 205 in "ADV7604 Hardware Manual, Rev. F, August 2010"
for details.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ignore EDID's where the header is wrong.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Whenever the hotplug pin is pulled low the chip resets a whole bunch
of registers. It turns out that this can be turned off on the adv7511.
Do so, as this 'feature' introduces race conditions in setting up
registers, particular when the hotplug pin bounces a lot.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Retry setup if the device is powered off when it should be powered on. This
state can be caused by rapid hotplug toggles.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removed dependency on rx-sense interrupt, it's a leftover from obsolete
code. Removing this simplifies the code.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ignore EDIDs where the header is wrong.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using two I2C operations between write and read,
use just one i2c_transfer. That allows I2C mutexes to not
let any other I2C transfer between the two.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver for Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with
embedded SoC ISP. The device is exposed as two V4L2 subdevices:
- S5K5BAF-CIS - the image sensor matrix, fixed 1600x1200 format,
no controls.
- S5K5BAF-ISP - the Image Signal Processor, formats up to 1600x1200,
pre/post ISP cropping, downscaling via selection API, controls.
[m.chehab@samsung.com: Whitespace cleanups]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>
The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
The MT9V034 sensor is very similar to the MT9V032, with a couple of
different registers and parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
To prepare support of the MT9V034, add the necessary infrastructure to
support model-specific parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Identify the model based on the I2C device name and configure formats
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor can scale the image down using binning by 1, 2 or 4 in both
directions. Update size enumeration and ratio and binning factor
computation accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The active pixel array size is 753x481 with 4 additional black rows at
the top. Fix the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vs6624_read() is only called in the conditionally-compiled
vs6624_g_register() function. Make the former conditionally-compiled as
well to silence build warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We had set the i2c clientdata to &flash->subdev_led[LM3560_LED1]
after call lm3560_subdev_init(flash, LM3560_LED1, "lm3560-led1"),
but the container_of() in lm3560_remove() return the wrong pointer
to flash.(should be container_of(subdev, struct lm3560_flash,
subdev_led[LM3560_LED_MAX-1])
This patch fix to set i2c clientdata to flash so we can get flash
from clientdata directly.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the missing unlock before return from function lm3560_set_ctrl()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git grep shows that the function is only called from ths7303.c
Fix this build warning:
CC drivers/media/i2c/ths7303.o
drivers/media/i2c/ths7303.c:86:5: warning: no previous prototype for ‘ths7303_setval’ [-Wmissing-prototypes]
int ths7303_setval(struct v4l2_subdev *sd, enum ths7303_filter_mode mode)
^
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct reference of reading values. (rval -> reg_val)
Add the missing unlock before return from function lm3560_get_ctrl()
to avoid deadlock.
Thank you Dan Carpenter & Sakari.
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
internal_csi_format_idx and csi_format_idx are unsigned integers,
therefore they can never be nevative.
CC drivers/media/i2c/smiapp/smiapp-core.o
In file included from include/linux/err.h:4:0,
from include/linux/clk.h:15,
from drivers/media/i2c/smiapp/smiapp-core.c:29:
drivers/media/i2c/smiapp/smiapp-core.c: In function ‘smiapp_update_mbus_formats’:
include/linux/kernel.h:669:20: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
#define min(x, y) ({ \
^
include/linux/compiler.h:153:42: note: in definition of macro ‘unlikely’
# define unlikely(x) __builtin_expect(!!(x), 0)
^
drivers/media/i2c/smiapp/smiapp-core.c:402:2: note: in expansion of macro ‘BUG_ON’
BUG_ON(min(internal_csi_format_idx, csi_format_idx) < 0);
^
drivers/media/i2c/smiapp/smiapp-core.c:402:9: note: in expansion of macro ‘min’
BUG_ON(min(internal_csi_format_idx, csi_format_idx) < 0);
^
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git grep shows that the function is only called from ths7303.c
Fix this build warning:
CC drivers/media/i2c/ths7303.o
drivers/media/i2c/ths7303.c:86:5: warning: no previous prototype for ‘ths7303_setval’ [-Wmissing-prototypes]
int ths7303_setval(struct v4l2_subdev *sd, enum ths7303_filter_mode mode)
^
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 5aa9ae5ed5 inverted the mute control
state test in s_routing which caused the audio routing to fail. This broke
ivtv support for the Hauppauge video/audio input bracket (which adds additional
video and audio inputs) all the way back in kernel 2.6.36.
This fix fixes the condition and it also removes a nonsense check on the
balance control.
Bisected-by: Rajil Saraswat <rajil.s@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Reported-by: Rajil Saraswat <rajil.s@gmail.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds the driver for the LM3560, dual LED Flash The LM3560 has two 1A
constant current driver for high current white LEDs.
It is controlled via an I2C compatible interface(up to 400kHz).
Each flash brightness, torch brightness and enable/disable can be
controlled independantly, but flash timeout and operation mode are shared.
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v3.12-rc fails to build with this error:
drivers/media/i2c/ths8200.c:49:2: error: unknown field 'bt' specified in initializer
drivers/media/i2c/ths8200.c:50:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:50:3: error: (near initialization for 'ths8200_timings_cap.reserved')
drivers/media/i2c/ths8200.c:51:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:51:3: error: (near initialization for 'ths8200_timings_cap.reserved')
...
with gcc 4.5.4. This error was not detected in builds prior to v3.12-rc.
This patch fixes this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org # For kernel v3.12
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct spelling typo within various part of the kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix to return -ENOMEM in the new i2c client and create workqueue error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
