Although we have a fixed setting for the PLL9 and EBB4 registers, it
still makes sense to check them together with the rest of PLL registers.
While at it also remove a redundant comment about 10 bit clock enabling.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CxSR (or maxfifo on VLV/CHV) blocks somne changes to the plane control
register (enable bit at least, not quite sure about the rest). So in
order to have the plane enable/disable when we want we need to first
kick the hardware out of cxsr.
Unfortunateloy this requires some extra vblank waits. For the CxSR
enable after the plane update we should eventually use an async
vblank worker, but since we don't have that just do sync vblank
waits. For the disable case we have no choice but to do it
synchronously.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to get decnet memory self refresh residency on VLV, flip it
over to the new CHV way of doing things. VLV doesn't do PM5 or DDR DVFS
so it's a bit simpler.
I'm not sure the currently memory latency used for CHV is really
appropriate for VLV. Some further testing will probably be needed to
figure that out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.
So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.
I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.
Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to update the watermarks on the right side of the plane update. This
is just a temporary hack until we get the proper two part update into
place. However in the meantime this might have some chance of at least
working.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
v3: Rebase after a long time and atomic path changes.
Accept Ville suggestion of not check !fb
v4: Re-factore on dinq
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
[danvet: Make it compile]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We cannot let IPS enabled with no plane on the pipe:
BSpec: "IPS cannot be enabled until after at least one plane has
been enabled for at least one vertical blank." and "IPS must be
disabled while there is still at least one plane enabled on the
same pipe as IPS." This restriction apply to HSW and BDW.
However a shortcut path on update primary plane function
to make primary plane invisible by setting DSPCTRL to 0
was leting IPS enabled while there was no
other plane enabled on the pipe causing flickerings that we were
believing that it was caused by that other restriction where
ips cannot be used when pixel rate is greater than 95% of cdclok.
v2: Don't mess with Atomic path as pointed out by Ville.
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=85583
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently we don't have any real indication when a pipe gets
enabled/disabled. Add some.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid some 'switch (plane->type)' by storing the fronbuffer_bits in
intel_plane.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: use singular frontbuffer_bits in intel_plane since a plan can
only ever have one bit. Discussed with Ville on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The registers and process differ from other platforms. If the hardware
was programmed incorrectly, this will return invalid cdclk values, which
should then cause reprogramming of the hardware.
v2(Matt): Return 19.2 MHz when DE PLL is disabled (Ville)
v3: Make less assumptions about the hardware state (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way data is available as soon as the view is passed into the call chain.
v2: Store size in bytes instead of pages under the appropriate name. (Chris Wilson)
v3: Use uint64_t instead of size_t. (Daniel Vetter)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new DRRS code it kinda sticks out, and we never managed to
get this to work well enough without causing issues. Time to wave
goodbye.
I've decided to keep the logic for programming the reduced clocks
intact, but everything else is gone. If anyone ever wants to resurrect
this we need to redo it all anyway on top of the frontbuffer tracking.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This typo lead to the crtc scaler getting enabled incorrectly and an
evantual state checker mismatch about the scaler_id.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was momentarily confused until I've double-checked that these
functions really only compute state and don't update the hardware
state. They once did that, but since Ander's rework of the dpll
computation flow that's no longer the case.
Rename them to avoid further confusion.
Note that the ilk code already follows the compute_dpll naming scheme
for computing the actual register value. DDI code goes with _calc_,
but that is close enough.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
As there is no OLR to check, the check_olr() function is now a no-op and can be
removed.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything above has been converted to use requests, intel_ring_begin()
can be updated to take a request instead of a ring. This also means that it no
longer needs to lazily allocate a request if no-one happens to have done it
earlier.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated intel_ring_cacheline_align() to take a request instead of a ring.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all callers of i915_add_request() have a request pointer to hand, it is
possible to update the add request function to take a request pointer rather
than pulling it out of the OLR.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the display page flip code to do explicit request creation and
submission rather than relying on the OLR and just hoping that the request
actually gets submitted at some random point.
The sequence is now to create a request, queue the work to the ring, assign the
known request to the flip queue work item then actually submit the work and post
the request.
Note that every single flip function used to finish with
'__intel_ring_advance(ring);'. However, immediately after they return there is
now an add request call which will do the advance anyway. Thus the many
duplicate advance calls have been removed.
v2: Updated commit message with comment about advance removal.
v3: The request can now be allocated by the _sync() code earlier on. Thus the
page flip path does not necessarily need to allocate a new request, it may be
able to re-use one.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The plan is to pass requests around as the basic submission tracking structure
rather than rings and contexts. This patch updates the i915_gem_object_sync()
code path.
v2: Much more complex patch to share a single request between the sync and the
page flip. The _sync() function now supports lazy allocation of the request
structure. That is, if one is passed in then that will be used. If one is not,
then a request will be allocated and passed back out. Note that the _sync() code
does not necessarily require a request. Thus one will only be created until
certain situations. The reason the lazy allocation must be done within the
_sync() code itself is because the decision to need one or not is not really
something that code above can second guess (except in the case where one is
definitely not required because no ring is passed in).
The call chains above _sync() now support passing a request through which most
callers passing in NULL and assuming that no request will be required (because
they also pass in NULL for the ring and therefore can't be generating any ring
code).
The exeception is intel_crtc_page_flip() which now supports having a request
returned from _sync(). If one is, then that request is shared by the page flip
(if the page flip is of a type to need a request). If _sync() does not generate
a request but the page flip does need one, then the page flip path will create
its own request.
v3: Updated comment description to be clearer about 'to_req' parameter (Tomas
Elf review request). Rebased onto newer tree that significantly changed the
synchronisation code.
v4: Updated comments from review feedback (Tomas Elf)
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next because the conflict between Ander's atomic fixes
for 4.2 and Maartens future work are getting to unwielding to handle.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_ringbuffer.h
Just always take ours, same as git merge -X ours, but done by hand
because I didn't trust git: It's confusing that it doesn't show any
conflicts in the merge diff at all.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The same dpll p2 divider selection is repeated three times in the
gen2-4 .find_dpll() functions. Factor it out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The skylake scalers depend on the cdclk freq, but that frequency can
change during a modeset. So when a modeset happens calculate the new
cdclk in the atomic state. With the transitional helpers gone the
cached value can be used in the scaler, and committed after all
crtc's are disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By making color key atomic there are no more transitional helpers.
The plane check function will reject the color key when a scaler is
active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to repeatedly call update_watermarks, or update_fbc.
Down to a single call to update_watermarks in .crtc_enable
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all planes are added during a modeset we can use the
calculated changes before disabling a plane, and then either commit
or force disable a plane before disabling the crtc.
The code is shared with atomic_begin/flush, except watermark updating
and vblank evasion are not used.
This is needed for proper atomic suspend/resume support.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the initial state, and add a quirk to force add all planes
to crtc_state->plane_mask during initial commit. This will disable
all planes during the initial modeset.
The initial plane quirk is temporary, and will go away when hardware
readout is fully atomic, and the watermark updates in intel_sprite.c
are removed.
Changes since v1:
- Unset state->visible on !primary planes.
- Do not rely on the plane->crtc pointer in intel_atomic_plane,
instead assume planes are invisible until modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the checks in intel_modeset_checks are only useful when a modeset
occurs, because there is nothing to update otherwise.
Same for power/cdclk changes, if there is no modeset they are noops.
Unfortunately intel_modeset_pipe_config still gets called without
modeset, because atomic hw readout isn't done yet.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To allow them to be used in intel_set_mode.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is probably intended to be be done during vblank evasion.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The idea was good, but planes can have a fb even though
they're disabled. This makes the force argument useless
and always true, because only the commit function updates
state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By passing crtc_state to the check_plane functions a lot of duplicated
code can be removed. There are still some transitional helper calls,
they will be removed later.
Changes since v1:
- Revert state->visible changes.
- Use plane->state->crtc instead of plane->crtc.
- Use drm_atomic_get_existing_crtc_state.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No point in hiding behind big ifs. This will be true most of the time.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes it easier to verify that no changes are done when
calling this from crtc instead.
Changes since v1:
- Make intel_wm_need_update static and always check it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 2c310b9d2859863826c3688c88218d607d5dd19a
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon May 18 12:28:52 2015 +0200
drm/i915: Split skl_update_scaler, v4.
It's easier to read separate functions for crtc and plane scaler state.
Changes since v1:
- Update documentation.
Changes since v2:
- Get rid of parameters to skl_update_scaler only used for traces.
This avoids needing to document the other parameters.
Changes since v3:
- Rename scaler_idx to scaler_user.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It saves another loop over all crtc's in the state, and computing
clock is more of a per crtc thing.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The scaler setup may add planes, but since they're unchanged we only
have to wait for primary flips. Also set planes_changed to indicate
at least 1 plane is modified.
Changes since v1:
- Instead of removing planes, do minimal validation needed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the check for encoder cloning here.
Changes since v1:
- Remove was/is crtc_disabled. (mattrope)
- Rename function to intel_crtc_atomic_check. (mattrope)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of a whole lot of ternary operators and assign the index
in scaler_id, instead of the id. They're the same thing.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Grabbing crtc state from atomic state is a lot more involved,
and make sure connectors are added before calling this function.
Move check_digital_port_conflicts to intel_modeset_checks,
it's only useful to check it on a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by(IVB): Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Silence the following -Wmaybe-uninitialized warnings and make the code
more clear.
drivers/gpu/drm/i915/intel_display.c: In function ‘__intel_set_mode’:
drivers/gpu/drm/i915/intel_display.c:11844:14: warning: ‘crtc_state’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return state->mode_changed || state->active_changed;
^
drivers/gpu/drm/i915/intel_display.c:11854:25: note: ‘crtc_state’ was declared here
struct drm_crtc_state *crtc_state;
^
drivers/gpu/drm/i915/intel_display.c:11868:6: warning: ‘crtc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (crtc != intel_encoder->base.crtc)
^
drivers/gpu/drm/i915/intel_display.c:11853:19: note: ‘crtc’ was declared here
struct drm_crtc *crtc;
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We need to call drm_atomic_set_mode_for_crtc() rather than copying the
mode in manually. As of commit
commit 99cf4a29fa
Author: Daniel Stone <daniels@collabora.com>
Date: Mon May 25 19:11:51 2015 +0100
drm/atomic: Add current-mode blob to CRTC state
the helper now also takes care of setting up the mode property blob for
us; if we don't use the helper and never setup the mode blob, this will
also trigger a failure in drm_atomic_crtc_check() when we have the
DRIVER_ATOMIC flag set (i.e., when using the nuclear pageflip support
via i915.nuclear_pageflip kernel command line parameter).
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code in intel_crtc_restore_mode() sets the enabled value of all the
CRTCs when restoring the mode after a suspend/resume cycle. When more
than one CRTC is enabled, that causes drm_atomic_helper_check_modeset()
to fail if there is more than one pipe enabled, since all but one CRTC
has valid connector data. Instead, set only the enabled value for the
CRTC passed as an argument.
v2: Don't leak atomic state. (Matt)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90468
References: https://bugs.freedesktop.org/show_bug.cgi?id=90396
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
The force restore path relies on the staged config to preserve the
configuration used before a suspend/resume cycle. The update done to it
in intel_modeset_fixup_state() would cause that information to be lost
after the first modeset, making it impossible to restore the modes for
pipes B and C.
References: https://bugs.freedesktop.org/show_bug.cgi?id=90468
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Since the force restore logic will restore the CRTCs state one at a
time, it is possible that the state will be inconsistent until the whole
operation finishes. A call to intel_modeset_check_state() is done once
it's over, so don't check the state multiple times in between. This
regression was introduced in:
commit 7f27126ea3
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Nov 5 14:26:06 2014 -0800
drm/i915: factor out compute_config from __intel_set_mode v3
v2: Rename check parameter to force_restore. (Matt)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94431
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Limit CHV maximum cdclk to 320MHz.
v2: Rebase to the latest
v3: Clean up of if-else tree
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs don't support the 64k linear scanout alignment we impose
on gen2/3. And it really makes no sense since we have no DSPSURF
register, so the only thing that the hardware will see is the linear
offset which will be just pixel aligned anyway.
There is one case where 64k comes into the picture, and that's FBC.
The start of the line length buffer corresponds to a 64k aligned
address of the uncompressed framebuffer. So if the uncompressed fb is
not 64k aligned, the first actually used entry in the line length
buffer will not be byte 0. There are 32 extra entries in the line
length buffer to account for this extra alignment so we shouldn't
have to worry about it when mapping the uncompressed fb to the GTT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have problems with 4k aligned linear scanout buffers. The VLV
docs got updated at some point to say that we need to align them to
128k, just like we do on gen4.
So far I've seen the problem manifest when the stride is an odd multiple
of 512 bytes, and the surface address meets the following pattern
'(addr & 0xf000) == 0x1000' (also == 0x2000 is problematic on VLV). The
result is a starcase effect (so some pages get dropped maybe?), with a
few pages here and there clearly getting scannout out at the wrong position.
I've not actually been able to reproduce this problem on gen4, so it's
not clear of the issue is any way related to the 128k restrictions
supposedly inherited from gen4. But let's hope the 128k alignment is
sufficient to hide it all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently intel_gen4_compute_page_offset() simply picks the closest
page boundary below the linear offset. That however may not be suitably
aligned to satisfy any hardware specific restrictions. So let's make
sure the page boundary we choose is properly aligned.
Also to play it a bit safer lets split the remaining linear offset into
x and y values instead of just x. This should make no difference for
most platforms since we convert the x and y offsets back into a linear
offset before feeding them to the hardware. HSW+ are different however
and use x and y offsets even with linear buffers, so they might have
trouble if either the x or y get too big.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915 atomic conversion is a real beast and it's not getting easier
wrangling in a separate branch. I'm might be regretting this, but
right after vacation nothing can burst my little bubble here!
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
I noticed one of those and it turned out we have a few lingering around.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Switch from using 31 PFI credits to 63 PFI credits when cdclk>=czclk on
CHV. The spec lists both 31 and 63 as "suggested" values, but based on
feedback from hardware folks we should actually be using 63. Originally
I picked the 31 basically by flipping a coin.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IBX BSpec says we must specify 8bpc in TRANSCONF for both 8bpc
and 12bpc HDMI output. Do so.
v2: Pass intel_crtc to intel_pipe_has_type()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was introduced after converting hw readout to atomic,
so it should have been part of the revert too.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90929
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use a full atomic call instead. intel_crtc_page_flip will still
have to live until async updates are allowed.
This doesn't seem to be a regression from the convert to atomic,
part 3 patch. During GPU reset it fixes the following warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 752 at drivers/gpu/drm/drm_crtc.c:5337 drm_mode_page_flip_ioctl+0x27b/0x360()
Modules linked in: i915
CPU: 0 PID: 752 Comm: Xorg Not tainted 4.1.0-rc7-patser+ #4090
Hardware name: NUC5i7RYB, BIOS RYBDWi35.86A.0246.2015.0309.1355 03/09/2015
ffffffff81c90866 ffff8800d87c3ca8 ffffffff817f7d87 0000000080000001
0000000000000000 ffff8800d87c3ce8 ffffffff81084955 ffff880000000000
ffff8800d87c3dc0 ffff8800d93d1208 0000000000000000 ffff8800b7d1f3e0
Call Trace:
[<ffffffff817f7d87>] dump_stack+0x4f/0x7b
[<ffffffff81084955>] warn_slowpath_common+0x85/0xc0
[<ffffffff81084a35>] warn_slowpath_null+0x15/0x20
[<ffffffff8146dffb>] drm_mode_page_flip_ioctl+0x27b/0x360
[<ffffffff8145ccb0>] drm_ioctl+0x1a0/0x6a0
[<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[<ffffffff812e5540>] ? avc_has_perm+0x20/0x280
[<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[<ffffffff811ea0f8>] do_vfs_ioctl+0x2f8/0x530
[<ffffffff811f6001>] ? expand_files+0x261/0x270
[<ffffffff812e7c16>] ? selinux_file_ioctl+0x56/0x100
[<ffffffff811ea3b1>] SyS_ioctl+0x81/0xa0
[<ffffffff81801b97>] system_call_fastpath+0x12/0x6f
---[ end trace 9ce834560085bd64 ]---
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should fix fallout caused by making intel_crtc_control
and update_dpms atomic, which became a problem after reverting the
atomic hw readout patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90929
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 3bae26eb2991c00670df377cf6c3bc2b0577e82a.
Seems it introduces regressions for 3 different reasons, oh boy..
In bug #90868 as I can see the atomic state will be restored on
resume without the planes being set up properly. Because plane
setup here requires the atomic state, we'll have to settle
for committing atomic planes first.
In bug #90861 the failure appears to affect mostly DP devices,
and happens because reading out the atomic state prevents a modeset
on boot, which would require better hw state readout.
In bug #90874 it's shown that cdclk should be part of the atomic
state, so only performing a single modeset during resume excarbated
the issue.
It's better to fix those issues first, and then commit this patch,
so do that temporarily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 490f400db5d886fc28566af69b02f6497f31be4b.
We're not ready yet to make it atomic, we calculate some state in
advance, but without atomic plane support atomic the hw readout will
fail.
It's required to revert this commit to revert the atomic hw
state readout patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
crtc->active will be gone eventually, and this check should be just as good.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a small behavioral change because it leaves DVO_2X_MODE
set between crtc_disable and crtc_enable. This is probably harmless
though and if not should be fixed by calculating 2x mode before
enable/disable pll.
This is needed because intel_crtc->active will be removed eventually.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This needs to be done last after all modesets have been calculated.
A modeset first disables all crtc's, so any crtc that undergoes a
modeset counts as inactive.
If no modeset's done, or > 1 crtc's stay w/a doesn't apply.
Apply workaround on the first crtc if 1 crtc stays active.
Apply workaround on the second crtc if no crtc was active.
Changes since v1:
- Use intel_crtc->atomic as a place to put hsw_workaround_pipe.
- Make sure quirk only applies to haswell.
- Use first loop to iterate over newly enabled crtc's only.
This increases readability.
Changes since v2:
- Move hsw_workaround_pipe back to crtc_state.
Changes since v3:
- Return errors from haswell_mode_set_planes_workaround.
Changes since v4:
- Clean up commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_crtc->config will be removed eventually, so use crtc->hwmode.
drm_atomic_helper_update_legacy_modeset_state updates hwmode,
but crtc->active will eventually be gone too. Set dotclock to zero
to indicate the crtc is inactive.
Changes since v1:
- With the hwmode update in drm*update_legacy_modeset_state removed,
intel_modeset_update_state has to assign it instead.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a preparation for passing crtc state to the helpers.
When converting all users of crtc->config to use the old or
new state it's easier to find regressions when swap_state is
done first.
If crtc->config is swapped at the same place as swap_state
bugs will never be found.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.
Calling intel_set_mode will cause intel_display_set_init_power to be
called, make sure init_power gets set again afterwards.
Changes since v1:
- Fix to compile with v2 of the patch that adds intel_display_suspend.
- Add intel_display_set_init_power.
- Set return value to int to allow error checking.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Assume the callers lock everything with drm_modeset_lock_all.
This change had to be done after converting suspend/resume to
use atomic_state so the atomic state is preserved, otherwise
all transitional state is erased.
Now all callers of .crtc_enable and .crtc_disable go through
atomic modeset! :-D
Changes since v1:
- Only check for crtc_state->active in valleyview_modeset_global_pipes.
- Only check for crtc_state->active in modeset_update_crtc_power_domains.
Changes since v2:
- Rework on top of the changed patch order.
Changes since v3:
- Rename intel_crtc_toggle in description to *_control
- Change return value to int.
- Do not add plane state, should be done implicitly already.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To make this work we load the new hardware state into the
atomic_state, then swap it with the sw state.
This lets us change the force restore path in setup_hw_state()
to use a single call to intel_mode_set() to restore all the
previous state.
As a nice bonus this kills off encoder->new_encoder,
connector->new_enabled and crtc->new_enabled. They were used only
to restore the state after a modeset.
Changes since v1:
- Make sure all possible planes are added with their crtc set,
so they will be turned off on first modeset.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It makes more sense there, since these are computation steps that can
fail.
Changes since v1:
- Rename __intel_set_mode_checks to intel_modeset_checks (Matt Roper)
- Move intel_modeset_checks to before check_planes, so it won't
have to be moved later.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Repeated calls to begin_crtc_commit can cause warnings like this:
[ 169.127746] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
[ 169.127835] in_atomic(): 0, irqs_disabled(): 1, pid: 1947, name: kms_flip
[ 169.127840] 3 locks held by kms_flip/1947:
[ 169.127843] #0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff814774bc>] __drm_modeset_lock_all+0x9c/0x130
[ 169.127860] #1: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffff814774cd>] __drm_modeset_lock_all+0xad/0x130
[ 169.127870] #2: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffff81477178>] drm_modeset_lock+0x38/0x110
[ 169.127879] irq event stamp: 665690
[ 169.127882] hardirqs last enabled at (665689): [<ffffffff817ffdb5>] _raw_spin_unlock_irqrestore+0x55/0x70
[ 169.127889] hardirqs last disabled at (665690): [<ffffffffc0197a23>] intel_pipe_update_start+0x113/0x5c0 [i915]
[ 169.127936] softirqs last enabled at (665470): [<ffffffff8108a766>] __do_softirq+0x236/0x650
[ 169.127942] softirqs last disabled at (665465): [<ffffffff8108ae75>] irq_exit+0xc5/0xd0
[ 169.127951] CPU: 1 PID: 1947 Comm: kms_flip Not tainted 4.1.0-rc4-patser+ #4039
[ 169.127954] Hardware name: LENOVO 2349AV8/2349AV8, BIOS G1ETA5WW (2.65 ) 04/15/2014
[ 169.127957] ffff8800c49036f0 ffff8800cde5fa28 ffffffff817f6907 0000000080000001
[ 169.127964] 0000000000000000 ffff8800cde5fa58 ffffffff810aebed 0000000000000046
[ 169.127970] ffffffff81c5d518 0000000000000268 0000000000000000 ffff8800cde5fa88
[ 169.127981] Call Trace:
[ 169.127992] [<ffffffff817f6907>] dump_stack+0x4f/0x7b
[ 169.128001] [<ffffffff810aebed>] ___might_sleep+0x16d/0x270
[ 169.128008] [<ffffffff810aed38>] __might_sleep+0x48/0x90
[ 169.128017] [<ffffffff817fc359>] mutex_lock_nested+0x29/0x410
[ 169.128073] [<ffffffffc01635f0>] ? vgpu_write64+0x220/0x220 [i915]
[ 169.128138] [<ffffffffc017fddf>] ? ironlake_update_primary_plane+0x2ff/0x410 [i915]
[ 169.128198] [<ffffffffc0190e75>] intel_frontbuffer_flush+0x25/0x70 [i915]
[ 169.128253] [<ffffffffc01831ac>] intel_finish_crtc_commit+0x4c/0x180 [i915]
[ 169.128279] [<ffffffffc00784ac>] drm_atomic_helper_commit_planes+0x12c/0x240 [drm_kms_helper]
[ 169.128338] [<ffffffffc0184264>] __intel_set_mode+0x684/0x830 [i915]
[ 169.128378] [<ffffffffc018a84a>] intel_crtc_set_config+0x49a/0x620 [i915]
[ 169.128385] [<ffffffff817fdd39>] ? mutex_unlock+0x9/0x10
[ 169.128391] [<ffffffff81467b69>] drm_mode_set_config_internal+0x69/0x120
[ 169.128398] [<ffffffff8119b547>] ? might_fault+0x57/0xb0
[ 169.128403] [<ffffffff8146bf93>] drm_mode_setcrtc+0x253/0x620
[ 169.128409] [<ffffffff8145c600>] drm_ioctl+0x1a0/0x6a0
[ 169.128415] [<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[ 169.128424] [<ffffffff811e9ab8>] do_vfs_ioctl+0x2f8/0x530
[ 169.128429] [<ffffffff810d0fcd>] ? trace_hardirqs_on+0xd/0x10
[ 169.128435] [<ffffffff812e7676>] ? selinux_file_ioctl+0x56/0x100
[ 169.128439] [<ffffffff811e9d71>] SyS_ioctl+0x81/0xa0
[ 169.128445] [<ffffffff81800697>] system_call_fastpath+0x12/0x6f
Solve it by using the newly introduced drm_atomic_helper_commit_planes_on_crtc.
The problem here was that the drm_atomic_helper_commit_planes() helper
we were using was basically designed to do
begin_crtc_commit(crtc #1)
begin_crtc_commit(crtc #2)
...
commit all planes
finish_crtc_commit(crtc #1)
finish_crtc_commit(crtc #2)
The problem here is that since our hardware relies on vblank evasion,
our CRTC 'begin' function waits until we're out of the danger zone in
which register writes might wind up straddling the vblank, then disables
interrupts; our 'finish' function re-enables interrupts after the
registers have been written. The expectation is that the operations between
'begin' and 'end' must be performed without sleeping (since interrupts
are disabled) and should happen as quickly as possible. By clumping all
of the 'begin' calls together, we introducing a couple problems:
* Subsequent 'begin' invocations might sleep (which is illegal)
* The first 'begin' ensured that we were far enough from the vblank that
we could write our registers safely and ensure they all fell within
the same frame. Adding extra delay waiting for subsequent CRTC's
wasn't accounted for and could put us back into the 'danger zone' for
CRTC #1.
This commit solves the problem by using a new helper that allows an
order of operations like:
for each crtc {
begin_crtc_commit(crtc) // sleep (maybe), then disable interrupts
commit planes for this specific CRTC
end_crtc_commit(crtc) // reenable interrupts
}
so that sleeps will only be performed while interrupts are enabled and
we can be sure that registers for a CRTC will be written immediately
once we know we're in the safe zone.
The crtc->config->base.crtc update may seem unrelated, but the helper
will use it to obtain the crtc for the state. Without the update it
will dereference NULL and crash.
Changes since v1:
- Use Matt Roper's commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that we can subclass drm_atomic_state we can also use it to keep
track of all the pll settings. atomic_state is a better place to hold
all shared state than keeping pll->new_config everywhere.
Changes since v1:
- Assert connection_mutex is held.
Changes since v2:
- Fix swapped arguments to kzalloc for intel_atomic_state_alloc. (Jani Nikula)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The primary plane can still be configured when crtc is off,
furthermore this is also a noop now that affected planes are
added on modesets.
Changes since v1:
- Move commit so no frontbuffer_bits warnings are generated.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Compute new pipe_configs for all crtcs in the atomic state. The commit
part of the mode set (__intel_set_mode()) is already enabled to support
multiple pipes, the only thing missing was calculating a new pipe_config
for every crtc.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should be much cleaner, with the same effects.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This can happen when turning off a sprite plane. Because the crtc state
is not yet always swapped correctly and transitional helpers are used
the crtc state cannot be relied on.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Atomic planes updates rely on having a accurate plane_mask.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add missing calls to drm_atomic_add_affected_*. This is needed
to convert to atomic planes. When converting to atomic all planes
are needed on modeset. For good measure make sure all connectors
are added too.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
crtc_state->enable means a crtc is configured, but it may be turned
off for dpms. Until the commit "use intel_crtc_control everywhere"
crtc_state->active was not updated on crtc off, but now
crtc_state->active should be used for tracking whether a crtc is
scanning out or not.
A few commits from now dpms will be handled by calling
intel_set_mode with a different value for crtc_state->active,
which causes a crtc to turn on or off.
At this point crtc->active should mirror crtc_state->active,
so some paranoia from the crtc_disable functions can be removed.
intel_set_mode_setup_plls still checks for ->enable, because all
resources that are needed have to be calculated, else
dpms changes may not succeed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
A follow up patch will make intel_modeset_compute_config() deal with
multiple crtcs, so move crtc specific stuff into the lower level crtc
specific function.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
With the use of drm_atomic_helper_update_legacy_modeset_state the
last user of modeset_crtc is removed from this function.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that the helper is exported there's no need to duplicate
this code any more.
Changes since v1:
- move intel_modeset_update_staged_output_state call to the right place.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Having a single path for everything makes it a lot easier to keep
crtc_state->active in sync with intel_crtc->active.
A crtc cannot be changed to active when not enabled, because it means
no mode is set and no connectors are connected.
This should also make intel_crtc->active match crtc_state->active.
Changes since v1:
- Reworded commit message, there's no intel_crtc_toggle.
Changes since v2:
- Change some callers of intel_crtc_control to intel_display_suspend.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a function used to disable all crtc's. This makes it clearer
to distinguish between when mode needs to be preserved and when
it can be trashed.
Changes since v1:
- Copy power changes from intel_crtc_control.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that the dpll updates are (mostly) atomic, the .off() code is a noop,
and intel_crtc_disable does mostly the same as intel_modeset_update_state.
Move all logic for connectors_active and setting dpms to that function.
Changes since v1:
- Move drm_atomic_helper_swap_state up.
Changes since v2:
- Split out intel_put_shared_dpll removal.
Changes since v3:
- Rebase on top of latest drm-intel.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Now that the pll updates are staged the put_shared_dpll function
consists only of checks that are done in check_shared_dpll_state
after a modeset too.
The changes to pll->config are overwritten by
intel_shared_dpll_commit, so this entire function is a noop.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville's and Mika's cdclk series was in flight at the same time as the
SKL S3 patches so we were missing that update.
intel_update_max_cdclk() and intel_update_cdclk() had to be moved up a
bit to avoid forward declarations.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We can operate with DPLL0 off with CDCLK backed by the 24Mhz reference
clock, and that's a supported configuration. Don't warn when notice
DPLL0 is off then.
We still have a separate warn at boot if cdclk is disabled (because we
don't currently try to handle the case (that shouldn't happen on SKL as
far as I know) where we boot with display not initialized.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add support for changing cdclk frequency during runtime on BDW.
Also with IPS enabled the actual pixel rate mustn't exceed 95% of cdclk,
so take that into account when computing the max pixel rate.
v2: Grab rps.hw_lock around sandybridge_pcode_write()
v3: Rebase due to power well vs. .global_resources() reordering
v4: Rebased to the latest
v5: Rebased to the latest
v6: Patch order shuffle so that Broadwell CD clock change is
applied before the patch for Haswell CD clock change
v7: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bspec says we shouldn't enable IPS on BDW when the pipe pixel rate
exceeds 95% of the core display clock. Apparently this can cause
underruns.
There's no similar restriction listed for HSW, so leave that one alone
for now.
v2: Add pipe_config_supports_ips() (Chris)
v3: Compare against the max cdclk insted of the current cdclk
v4: Rebased to the latest
v5: Rebased to the latest
v6: Fix for patch style problems
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83497
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Keep the cdclk maximum supported frequency around in dev_priv so that we
can verify certain things against it before actually changing the cdclk
frequency.
For now only VLV/CHV have support changing cdclk frequency, so other
plarforms get to assume cdclk is fixed.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rather than reading out the current cdclk value use the cached value we
have tucked away in dev_priv.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Fix for patch style problems
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rather that extracting the current cdclk freuqncy every time someone
wants to know it, cache the current value and use that. VLV/CHV already
stored a cached value there so just expand that to cover all platforms.
v2: Rebased to the latest
v3: Rebased to the latest
v4: Rebased to the latest
v5: Removed spurious call to 'intel_update_cdclk(dev)' based on
Damien Lespiau's comment
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Silence the following -Wmaybe-uninitialized warnings and make the code
more clear.
drivers/gpu/drm/i915/intel_display.c: In function ‘__intel_set_mode’:
drivers/gpu/drm/i915/intel_display.c:11844:14: warning: ‘crtc_state’ may be used uninitialized in this function [-Wmaybe-uninitialized]
return state->mode_changed || state->active_changed;
^
drivers/gpu/drm/i915/intel_display.c:11854:25: note: ‘crtc_state’ was declared here
struct drm_crtc_state *crtc_state;
^
drivers/gpu/drm/i915/intel_display.c:11868:6: warning: ‘crtc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (crtc != intel_encoder->base.crtc)
^
drivers/gpu/drm/i915/intel_display.c:11853:19: note: ‘crtc’ was declared here
struct drm_crtc *crtc;
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Without this frontbuffer flip when enabling planes PSR got compromised
and wasn't being enabled waiting forever on the flush that never
arrived.
Another solution would to create a enable_cursor function and split this
frontbuffer flip among the different plane enable and disable functions.
But if necessary this can be done in a follow up work. For now let's
just fix the regression.
It was removed by:
commit 87d4300a7d
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Apr 21 17:12:54 2015 +0300
drm/i915: Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use it there.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Print a warning if we fall through the .get_display_clock_speed() function
pointer setup. We end up assuming a 133MHz cdclk which should mean that
at least we avoid any 0 deivisions and whatnot. But this could at least
help remind people that they have to provide this function for new platforms.
v2: Rebased to the latest
v3: Rebased to the latest
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
