I don't think these PM functions can race with userland net device
operations, but it's much easier to reason about locking if state is
consistently guarded by the same lock.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
STATE_INIT and STATE_FINI are equivalent and represent incompletely
initialised states; combine them as STATE_UNINIT.
Rename STATE_RUNNING to STATE_READY, to avoid confusion with
netif_running() and IFF_RUNNING.
The comments do not quite match current usage, but this will be
corrected in subsequent fixes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We only use tso_state::full_packet_space to calculate the IPv4 tot_len
or IPv6 payload_len, not to set tso_state::packet_space. Replace it
with an ip_base_len field holding the value of tot_len or payload_len
before including the TCP payload, which is much more useful when
constructing the new headers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
TSO header buffers contain a control structure immediately followed by
the packet headers, and are kept on a free list when not in use. This
complicates buffer management and tends to result in cache read misses
when we recycle such buffers (particularly if DMA-coherent memory
requires caches to be disabled).
Replace the free list with a simple mapping by descriptor index. We
know that there is always a payload descriptor between any two
descriptors with TSO header buffers, so we can allocate only one
such buffer for each two descriptors.
While we're at it, use a standard error code for allocation failure,
not -1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We now have a definite upper bound on the number of descriptors per
skb; use that to stop the queue when the next packet might not fit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add a flags field to struct efx_tx_buffer, replacing the
continuation and map_single booleans.
Since a single descriptor cannot be both a TSO header and the last
descriptor for an skb, unionise efx_tx_buffer::{skb,tsoh} and add
flags for validity of these fields.
Clear all flags in free buffers (whereas previously the continuation
flag would be set).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Similar to fsl_pq_mdio.c, this driver is for the 10G MDIO controller on
Freescale Frame Manager Ethernet controllers.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ethtool.h, e1000, e1000e, and igb to
implement MDI/MDIx control.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking update from David Miller:
"A couple weeks of bug fixing in there. The largest chunk is all the
broken crap Amerigo Wang found in the netpoll layer."
1) netpoll and it's users has several serious bugs:
a) uses GFP_KERNEL with locks held
b) interfaces requiring interrupts disabled are called with them
enabled
c) and vice versa
d) VLAN tag demuxing, as per all other RX packet input paths, is not
applied
All from Amerigo Wang.
2) Hopefully cure the ipv4 mapped ipv6 address TCP early demux bugs for
good, from Neal Cardwell.
3) Unlike AF_UNIX, AF_PACKET sockets don't set a default credentials
when the user doesn't specify one explicitly during sendmsg().
Instead we attach an empty (zero) SCM credential block which is
definitely not what we want. Fix from Eric Dumazet.
4) IPv6 illegally invokes netdevice notifiers with RCU lock held, fix
from Ben Hutchings.
5) inet_csk_route_child_sock() checks wrong inet options pointer, fix
from Christoph Paasch.
6) When AF_PACKET is used for transmit, packet loopback doesn't behave
properly when a socket fanout is enabled, from Eric Leblond.
7) On bluetooth l2cap channel create failure, we leak the socket, from
Jaganath Kanakkassery.
8) Fix all the netprio file handling bugs found by Al Viro, from John
Fastabend.
9) Several error return and NULL deref bug fixes in networking drivers
from Julia Lawall.
10) A large smattering of struct padding et al. kernel memory leaks to
userspace found of Mathias Krause.
11) Conntrack expections in netfilter can access an uninitialized timer,
fix from Pablo Neira Ayuso.
12) Several netfilter SIP tracker bug fixes from Patrick McHardy.
13) IPSEC ipv6 routes are not initialized correctly all the time,
resulting in an OOPS in inet_putpeer(). Also from Patrick McHardy.
14) Bridging does rcu_dereference() outside of RCU protected area, from
Stephen Hemminger.
15) Fix routing cache removal performance regression when looking up
output routes that have a local destination. From Zheng Yan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
af_netlink: force credentials passing [CVE-2012-3520]
ipv4: fix ip header ident selection in __ip_make_skb()
ipv4: Use newinet->inet_opt in inet_csk_route_child_sock()
tcp: fix possible socket refcount problem
net: tcp: move sk_rx_dst_set call after tcp_create_openreq_child()
net/core/dev.c: fix kernel-doc warning
netconsole: remove a redundant netconsole_target_put()
net: ipv6: fix oops in inet_putpeer()
net/stmmac: fix issue of clk_get for Loongson1B.
caif: Do not dereference NULL in chnl_recv_cb()
af_packet: don't emit packet on orig fanout group
drivers/net/irda: fix error return code
drivers/net/wan/dscc4.c: fix error return code
drivers/net/wimax/i2400m/fw.c: fix error return code
smsc75xx: add missing entry to MAINTAINERS
net: qmi_wwan: new devices: UML290 and K5006-Z
net: sh_eth: Add eth support for R8A7779 device
netdev/phy: skip disabled mdio-mux nodes
dt: introduce for_each_available_child_of_node, of_get_next_available_child
net: netprio: fix cgrp create and write priomap race
...
This is the implementation for igb to allow forcing MDI state
via ethtool, allowing users to work around some improperly
behaving switches.
Forcing in this driver is for now only allowed when auto-neg is
enabled.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some users report issues with link failing when connected to certain
switches. This gives the user the ability to control the MDI state
from the driver, allowing users to work around some improperly
behaving switches.
Forcing in this driver is for now only allowed when auto-neg is
enabled.
This is in regards to the related ethtool app patch and
bugzilla.kernel.org bug 11998
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: bruce.w.allan@intel.com
CC: n.poppelier@xs4all.nl
CC: bastien@durel.org
CC: jsveiga@it.eng.br
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the implementation in e1000 to allow ethtool to force
MDI state, allowing users to work around some improperly
behaving switches.
Forcing in this driver is for now only allowed when auto-neg is enabled.
To use must have the matching version of ethtool app that supports
this functionality.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order for igb to support MDI setting support via
ethtool this code is needed to allow setting the MDI state
via software.
This is in regards to the related ethtool patch
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order for e1000e to support MDI setting support via
ethtool this code is needed to allow setting the MDI state
via software.
This is in regards to the related ethtool patch and
fixes bugzilla.kernel.org bug 11998
Signed-off-by: Bruce W Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When getting clock, give a chance to the CPUs without DT support,
which use Common Clock Framework, such as Loongson1B.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- IPoIB fixes for regressions introduced by path database conversion
- mlx4 fixes for bugs with large memory systems and regressions from SR-IOV patches
- RDMA CM fix for passing bad event up to userspace
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hN/H
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Grab bag of InfiniBand/RDMA fixes:
- IPoIB fixes for regressions introduced by path database conversion
- mlx4 fixes for bugs with large memory systems and regressions from
SR-IOV patches
- RDMA CM fix for passing bad event up to userspace
- Other minor fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check iboe netdev pointer before dereferencing it
mlx4_core: Clean up buddy bitmap allocation
mlx4_core: Fix integer overflow issues around MTT table
mlx4_core: Allow large mlx4_buddy bitmaps
IB/srp: Fix a race condition
IB/qib: Fix error return code in qib_init_7322_variables()
IB: Fix typos in infiniband drivers
IB/ipoib: Fix RCU pointer dereference of wrong object
IB/ipoib: Add missing locking when CM object is deleted
RDMA/ucma.c: Fix for events with wrong context on iWARP
RDMA/ocrdma: Don't call vlan_dev_real_dev() for non-VLAN netdevs
IB/mlx4: Fix possible deadlock on sm_lock spinlock
This change updates the code related to configuring the transmit frame
checksum. Specifically I have updated the code so that we can only skip
inserting the checksum in the case that we are not performing some other
offload that will modify the frame data.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change moves the RSC code into the non-EOP descriptor handling
function. The main motivation behind this change is to help reduce the
overhead in the non-RSC case. Previously the non-RSC path code would
always be checking for append count even if RSC had been disabled. Now
this code is completely skipped in a single conditional check instead of
having to make two separate checks.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch creates a function named ixgbe_fetch_rx_buffer. The sole
purpose of this function is to retrieve a single buffer off of the ring and
to place it in an skb.
The advantage to doing this is that it helps improve the readability since
I can decrease the indentation and for the code in this section.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change makes it so that if only the first 256 bytes of a buffer are
used we just copy the data out and leave the offset and page count
unchanged. There are multiple advantages to this. First it allows us to
reuse the page much more in the case of pages larger than 4K. It also
allows us to avoid some expensive atomic operations in the form of
get_page/put_page. In perf I have seen CPU utilization for put_page drop
from 3.5% to 1.8% as a result of this patch when doing small packet routing,
and packet rates increased by about 3%.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change creates a separate function for functionality similar to
pskb_pull_tail. The main motivation for moving it to a separate function
is so that later I can just skip this function in the case where we have
already copied the buffer into skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch makes it so that we will always have ownership of the buffers by
the time we get to ixgbe_add_rx_frag. This is necessary as I am planning to
add a copy-break to ixgbe_add_rx_frag and in order for that to function
correctly we need the CPU to have ownership of the buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change makes it so that we do not use double buffering if the page
size is larger than 4K. Instead we will simply walk through the page using
up to 3K per receive, and if we receive less than we only move the offset
by that amount. We will free the page when there is no longer any space
left that we can use instead of checking the page count to see if we can
cycle back to the start.
The main motivation behind this is to avoid the unnecessary truesize cost
for using a half page when most packets are 2K or smaller. With this new
approach the largest possible truesize for a page fragment will be 3K when
PAGE_SIZE is larger than 4K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch combines ixgbe_add_rx_frag and ixgbe_can_reuse_page into a
single function. The main motivation behind this is to make better use of
the values so that we don't have to load them from memory and into
registers twice.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This change reverts an earlier patch that introduced
ixgbe_init_rx_page_offset. The idea behind the function was to provide
some variation in the starting offset for the page in order to reduce
hot-spots in the cache. However it doesn't appear to provide any
significant benefit in the testing I have done. It has however been a
source of several bugs, and it blocks us from being able to use 2K
fragments on larger page sizes. So the decision I made was to remove it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
- Use kcalloc() / vzalloc() instead of an extra bitmap_zero().
- Add __GFP_NOWARN to kcalloc() since we'll try vzalloc() if it fails.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix some issues around int variables used in data structures related
to memory registration.
Handle int overflow in mlx4_init_icm_table by using a u64 intermediate
variable and changing struct mlx4_icm_table num_obj field to be u32.
Change some more fields/variables to use u32 instead of int to prevent
a case where the variable becomes negative when bit 31 is set.
Also subtract log_mtts_per_seg from the exponent when computing
num_mtt, since its added later on in that very same code area.
This and the previous commit fixes some issues which actually prevent
commit db5a7a65c0 ("mlx4_core: Scale size of MTT table with system
RAM") from working. Now, when the number of MTTs is scaled with the
size of the RAM we can map up to 8TB.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
mlx4_buddy_init uses kmalloc() to allocate bitmaps, which fails when
the required size is beyond the max supported value (or when memory is
too fragmented to handle a huge allocation). Extend this to use use
vmalloc() if kmalloc() fails, and take that into account when freeing
the bitmaps as well.
This fixes a driver load failure when log num mtt is 26 or higher, and
is a step in the direction of allowing to register huge amounts of
memory on large memory systems.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compiler warnings:
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:2908:3: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:1709:7: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: Joren Van Onder <joren.vanonder@gmail.com>
Acked-By: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing braces around the 10gig link check to include the check for KR support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Sascha Wildner <saw@online.de>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, every function probed clears the recovery registers from
all functions on its path - thus signaling that given a future recovery
event, there will be no need to wait for those functions.
This is a flawed behaviour - each function should only be responsible
for its own bit.
Since this registers are handled during the load/unload routines,
this cleanup is removed altogether.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing previous driver unload flow is flawed, causing the probe of
functions reaching the 'uncommon fork' in flr-capable devices to fail.
This patch resolves this, as well as fixing the flow for hypervisors which
disable flr capabilities from functions as they pass them as PDA to VMs,
as we cannot base the flow on the pci configuration space.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the register defines for DCA were never updated after going from
82575 to 82576. This change addresses that by updating the defines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch avoids phys_to_virt() by using skb->data and the address of the
pages allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch avoids phys_to_virt() by making using skb->data and the address
of the pages allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Driver probe functions are generally __devinit so they will be
discarded after initialization for non-hotplug kernels.
This was found by a new warning after patch 6a228452d "stmmac: Add
device-tree support" adds a new __devinit function that is called
from stmmac_pltfr_probe.
Without this patch, building socfpga_defconfig results in:
WARNING: drivers/net/ethernet/stmicro/stmmac/stmmac.o(.text+0x5d4c): Section mismatch in reference from the function stmmac_pltfr_probe() to the function .devinit.text:stmmac_probe_config_dt()
The function stmmac_pltfr_probe() references
the function __devinit stmmac_probe_config_dt().
This is often because stmmac_pltfr_probe lacks a __devinit
annotation or the annotation of stmmac_probe_config_dt is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The #ifdefs regarding CONFIG_ARCH_LPC32XX_MII_SUPPORT and
CONFIG_ARCH_LPC32XX_IRAM_FOR_NET are obsolete since the symbols have been
removed from Kconfig and replaced by devicetree based configuration.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
device tree implementation for davinci mdio driver
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some 8086:10c9 NICs have a problem completing the ethtool loopback test.
The result looks like this:
ethtool -t eth1
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 13
Link test (on/offline) 0
A bisect clearly points to commit a95a07445e.
However that seems to only trigger the bug. While adding some printk the
problem disappeared, so this might be a timing issue. After some trial and
error I discovered that adding a small delay just before igb_write_phy_reg()
in igb_integrated_phy_loopback() allows the loopback test to succeed.
I was unable to figure out the root cause so far but I expect it to be
somewhere in the following executing path
igb_integrated_phy_loopback
->igb_write_phy_reg_igp
->igb_write_phy_reg_mdic
->igb_acquire_phy_82575
->igb_acquire_swfw_sync_82575
The problem could only be observed on 8086:10c9 NICs so far and not all
of them show the behaviour. I did not restrict the workaround to this
type of NIC as it should do no harm to other igb NICs.
With the patch below the loopback test succeeded 500 times in a row
using a NIC that would otherwise fail.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
A bus trace shows that while executing e1000e_down, TCTL is cleared except
for the PSP bit. This occurs while in the middle of fetching a TSO packet
since the Tx packet buffer is full at that point. Before the device is
reset, the e1000_watchdog_task starts to run from the middle (it was
apparently pre-empted earlier, although that is not in the trace) and sets
TCTL.EN. At that point, 82571 transmits the corrupted packet, apparently
because TCTL.MULR was cleared in the middle of fetching a packet, which is
forbidden.
Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of
clearing the entire register, so as not to change any settings in the
middle of fetching a packet.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Found that commit d478eb44 was a bad commit.
If the link partner is transmitting codeword (even if NULL codeword),
then the RXCW.C bit will be set so check for RXCW.CW is unnecessary.
Ref: RH BZ 840642
Reported-by: Fabio Futigami <ffutigam@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
CC: Marcelo Ricardo Leitner <mleitner@redhat.com>
CC: stable <stable@vger.kernel.org> [2.6.38+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
When building with ixp4xx_eth and ptp_ixp46x as module, one is getting the
following error:
ERROR: "ixp46x_phc_index" [drivers/ptp/ptp_ixp46x.ko] undefined!
This has been introduced by commit 509a7c2572.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even when they go beyond 80 characters, user visible strings should be
on one line to make them easy to grep for.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
