This is the main peripheral IRQ controller on the BCM7xxx MIPS chips;
it has the following characteristics:
- 64 to 160+ level IRQs
- Atomic set/clear registers
- Reasonably predictable register layout (N status words, then N
mask status words, then N mask set words, then N mask clear words)
- SMP affinity supported on most systems
- Typically connected to MIPS IRQ 2,3,2,3 on CPUs 0,1,2,3
This driver registers one IRQ domain and one IRQ chip to cover all
instances of the block. Up to 4 instances of the block may appear, as
it supports 4-way IRQ affinity on BCM7435.
The same block exists on the ARM BCM7xxx chips, but typically the ARM GIC
is used instead. So this driver is primarily intended for MIPS STB chips.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jaedon.shin@gmail.com
Cc: abrestic@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: jogo@openwrt.org
Cc: arnd@arndb.de
Cc: computersforpeace@gmail.com
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8844/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Pistachio SoC boots only with device-tree. Document the required
properties and nodes as well as the boot protocol between the bootlaoder
and the kernel.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9568/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a rather unpleasantly large set of bug fixes for arm-soc,
Most of them because of cross-tree dependencies for Exynos
where we should have figured out the right path to merge things
before the merge window, and then the maintainer being unable to
sort things out in time during a business trip.
The other changes contained here are the usual collection:
MAINTAINERS file updates
- Gregory Clement is now a co-maintainer for the legacy Marvell EBU
platforms
- A MAINTAINERS entry for the Freescale Vybrid platform that was
added last year
- Matt Porter no longer works as a maintainer on Broadcom SoCs
Build-time issues
- A compile-time error for at91
- Several minor DT fixes on at91, imx, exynos, socfpga, and omap
- The new digicolor platform was not correctly enabled at all
Configuration issues
- Two defconfig fix for regressions using USB on versatile
express and on OMAP3
- Enabling all 8 CPUs on Allwinner/SUNxi
- Enabling the new STiH410 platform to be usable
Bug fixes in platform code
- A missing barrier for socfpga
- Fixing LPDDR1 self-refresh mode on at91
- Fixing RTC interrupt numbers on Exynos3250
- Fixing a cache-coherency issues in CPU power-down
on Exynos5
- Multiple small OMAP power management fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Lr/j
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather unpleasantly large set of bug fixes for arm-soc, Most
of them because of cross-tree dependencies for Exynos where we should
have figured out the right path to merge things before the merge
window, and then the maintainer being unable to sort things out in
time during a business trip.
The other changes contained here are the usual collection:
MAINTAINERS file updates
- Gregory Clement is now a co-maintainer for the legacy Marvell EBU
platforms
- A MAINTAINERS entry for the Freescale Vybrid platform that was
added last year
- Matt Porter no longer works as a maintainer on Broadcom SoCs
Build-time issues
- A compile-time error for at91
- Several minor DT fixes on at91, imx, exynos, socfpga, and omap
- The new digicolor platform was not correctly enabled at all
Configuration issues
- Two defconfig fix for regressions using USB on versatile express
and on OMAP3
- Enabling all 8 CPUs on Allwinner/SUNxi
- Enabling the new STiH410 platform to be usable
Bug fixes in platform code
- A missing barrier for socfpga
- Fixing LPDDR1 self-refresh mode on at91
- Fixing RTC interrupt numbers on Exynos3250
- Fixing a cache-coherency issues in CPU power-down on Exynos5
- Multiple small OMAP power management fixes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (69 commits)
MAINTAINERS: Add myself as co-maintainer to the legacy support of the mvebu SoCs
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: vexpress: update CONFIG_USB_ISP1760 option
ARM: digicolor: add the machine directory to Makefile
ARM: STi: Add STiH410 SoC support
MAINTAINERS: add Freescale Vybrid SoC
MAINTAINERS: Remove self as ARM mach-bcm co-maintainer
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
...
- Fix for stdout-path option parsing with added unittest
- Fix for stdout-path interaction with earlycon
- Several DT unittest fixes
- Fix Sparc allmodconfig build error on
of_platform_register_reconfig_notifier
- Several DT overlay kconfig and build warning fixes
- Several DT binding documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVAvyzAAoJEMhvYp4jgsXiKSAIALRxbtnjPu13+1vD6C8xcTsN
TsD/GoIOtBjVlEPDFrKXOhRXkxXbgONDSveQYhm0iWr30ECloVoikIxF2NPty2nR
B3xN7WbbmeEBl1ubGVw60xs/M1cF7d11UpjRabjlVqFpMll5LufX0+ZAbLQ+Brsl
5zSGxIonG8pRxFy0yi6++76cyywn3XVYoUTMb+nKaiSzXvOBhGnm5MXruiynVH9m
enVKop8rhizfUdvSHFfxxipFK9L3+EYx0yxaZWW9tvYh6yHhb/GZxQcuz1Rn5KUJ
wY0Y4PJdusLOO0FNprZmLsi3GxEXOIBS0bcPCXQAqD/Kr46waVOETajyIItMYnY=
=nyIQ
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix for stdout-path option parsing with added unittest
- fix for stdout-path interaction with earlycon
- several DT unittest fixes
- fix Sparc allmodconfig build error on of_platform_register_reconfig_notifier
- several DT overlay kconfig and build warning fixes
- several DT binding documentation updates
* tag 'devicetree-fixes-for-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/platform: Fix sparc:allmodconfig build
of: unittest: Add options string testcase variants
of: fix handling of '/' in options for of_find_node_by_path()
of/unittest: Fix the wrong expected value in of_selftest_property_string
of/unittest: remove the duplicate of_changeset_init
dt: submitting-patches: clarify that DT maintainers are to be cced on bindings
of: unittest: fix I2C dependency
of/overlay: Remove unused variable
Documentation: DT: Renamed of-serial.txt to 8250.txt
of: Fix premature bootconsole disable with 'stdout-path'
serial: add device tree binding documentation for ETRAX FS UART
of/overlay: Directly include idr.h
of: Drop superfluous dependance for OF_OVERLAY
of: Add vendor prefix for Arasan
of: Add prompt for OF_OVERLAY config
This patch adds support to STiH410 SoC.
Please note "st,stih410" is already present in device tree.
The problem is that it is missing the entry in the match table,
and so the L2 cache and other cpus than 0 don't get initialized.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The exact steps provided for submitting binding patches can be read
as requiring the bindings to be sent only to the devicetree@vger.kernel.org
list. Since the DT maintainers would like to be Cced on any binding
submissions, make this requirement explicit in step 2.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The file of-serial.txt was only for 8250 compatible UART implementations,
so renamed it to 8250.txt to avoid confusing other persons.
This is suggested by Arnd, see:
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-September/291455.html
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into HEAD
Linux 4.0-rc3
Merging in v4.0-rc3 because commit 30a22c215a (console: Fix
console name size mismatch) is a dependency.
Pull networking fixes from David Miller:
1) nft_compat accidently truncates ethernet protocol to 8-bits, from
Arturo Borrero.
2) Memory leak in ip_vs_proc_conn(), from Julian Anastasov.
3) Don't allow the space required for nftables rules to exceed the
maximum value representable in the dlen field. From Patrick
McHardy.
4) bcm63xx_enet can accidently leave interrupts permanently disabled
due to errors in the NAPI polling exit logic. Fix from Nicolas
Schichan.
5) Fix OOPSes triggerable by the ping protocol module, due to missing
address family validations etc. From Lorenzo Colitti.
6) Don't use RCU locking in sleepable context in team driver, from Jiri
Pirko.
7) xen-netback miscalculates statistic offset pointers when reporting
the stats to userspace. From David Vrabel.
8) Fix a leak of up to 256 pages per VIF destroy in xen-netaback, also
from David Vrabel.
9) ip_check_defrag() cannot assume that skb_network_offset(),
particularly when it is used by the AF_PACKET fanout defrag code.
From Alexander Drozdov.
10) gianfar driver doesn't query OF node names properly when trying to
determine the number of hw queues available. Fix it to explicitly
check for OF nodes named queue-group. From Tobias Waldekranz.
11) MID field in macb driver should be 12 bits, not 16. From Punnaiah
Choudary Kalluri.
12) Fix unintentional regression in traceroute due to timestamp socket
option changes. Empty ICMP payloads should be allowed in
non-timestamp cases. From Willem de Bruijn.
13) When devices are unregistered, we have to get rid of AF_PACKET
multicast list entries that point to it via ifindex. Fix from
Francesco Ruggeri.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tipc: fix bug in link failover handling
net: delete stale packet_mclist entries
net: macb: constify macb configuration data
MAINTAINERS: add Marc Kleine-Budde as co maintainer for CAN networking layer
MAINTAINERS: linux-can moved to github
can: kvaser_usb: Read all messages in a bulk-in URB buffer
can: kvaser_usb: Avoid double free on URB submission failures
can: peak_usb: fix missing ctrlmode_ init for every dev
can: add missing initialisations in CAN related skbuffs
ip: fix error queue empty skb handling
bgmac: Clean warning messages
tcp: align tcp_xmit_size_goal() on tcp_tso_autosize()
net: fec: fix unbalanced clk disable on driver unbind
net: macb: Correct the MID field length value
net: gianfar: correctly determine the number of queue groups
ipv4: ip_check_defrag should not assume that skb_network_offset is zero
net: bcmgenet: properly disable password matching
net: eth: xgene: fix booting with devicetree
bnx2x: Force fundamental reset for EEH recovery
xen-netback: refactor xenvif_handle_frag_list()
...
Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other serial
driver bugfixes as well. Most notable is a wait_until_sent bugfix that
was traced back to being around since before 2.6.12 that Johan has fixed
up.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8RCYACgkQMUfUDdst+yk62QCgycxS4giC2hyRver3dyvaNR6g
zYYAn2w0uRndW+AqP4Tls54isRz6owpF
=gA2k
-----END PGP SIGNATURE-----
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTwygoACgkQMUfUDdst+yk8ZQCdFYB9t3ZIzxiobR1pQy/PJ6Ld
dxEAnRrKzKn1FaJKCkHg35YrInKVwScZ
=tRWZ
-----END PGP SIGNATURE-----
Merge tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull "code of conflict" from Greg KH:
"This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it"
[ Let's see how this works ]
* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Code of Conflict
Pull i2c fixes from Wolfram Sang:
"A set of updates and bugfixes for the new designware-baytrail driver.
And a documentation bugfix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: add required clocks property to binding
i2c: designware-baytrail: baytrail_i2c_acquire() might sleep
i2c: designware-baytrail: cross-check lock functions
i2c: designware-baytrail: fix sparse warnings
i2c: designware-baytrail: fix typo in error path
i2c: designware-baytrail: describe magic numbers
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A clock specifier is required for i.MX I2C and is
provided in all DTS implementations. Add this to the
list of required properties in the binding.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- Fix ACPI resources management problems introduced by the recent
rework of the code in question (Jiang Liu) and a build issue
introduced by those changes (Joachim Nilsson).
- Fix a recent suspend-to-idle regression on systems where entering
idle states causes local timers to stop, prevent suspend-to-idle
from crashing in restricted configurations (no cpuidle driver,
cpuidle disabled etc.) and clean up the idle loop somewhat while
at it (Rafael J Wysocki).
- Fix build problem in the cpufreq ppc driver (Geert Uytterhoeven).
- Allow the ACPI backlight driver module to be loaded if ACPI is
disabled which helps the i915 driver in those configurations
(stable-candidate) and change the code to help debug unusual use
cases (Chris Wilson).
- Wakeup IRQ management changes in v3.18 caused some drivers on the
at91 platform to trigger a warning from the IRQ core related to
an unexpected combination of interrupt action handler flags.
However, on at91 a timer IRQ is shared with some other devices
(including system wakeup ones) and that leads to the unusual
combination of flags in question. To make it possible to avoid
the warning introduce a new interrupt action handler flag (which
can be used by drivers to indicate the special case to the core)
and rework the problematic at91 drivers to use it and work as
expected during system suspend/resume. From Boris Brezillon,
Rafael J Wysocki and Mark Rutland.
- Clean up the generic power domains subsystem's debugfs interface
(Kevin Hilman).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nc5T
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes for recent regressions (ACPI resources management,
suspend-to-idle), stable-candidate fixes (ACPI backlight), fixes
related to the wakeup IRQ management changes made in v3.18, other
fixes (suspend-to-idle, cpufreq ppc driver) and a couple of cleanups
(suspend-to-idle, generic power domains, ACPI backlight).
Specifics:
- Fix ACPI resources management problems introduced by the recent
rework of the code in question (Jiang Liu) and a build issue
introduced by those changes (Joachim Nilsson).
- Fix a recent suspend-to-idle regression on systems where entering
idle states causes local timers to stop, prevent suspend-to-idle
from crashing in restricted configurations (no cpuidle driver,
cpuidle disabled etc.) and clean up the idle loop somewhat while at
it (Rafael J Wysocki).
- Fix build problem in the cpufreq ppc driver (Geert Uytterhoeven).
- Allow the ACPI backlight driver module to be loaded if ACPI is
disabled which helps the i915 driver in those configurations
(stable-candidate) and change the code to help debug unusual use
cases (Chris Wilson).
- Wakeup IRQ management changes in v3.18 caused some drivers on the
at91 platform to trigger a warning from the IRQ core related to an
unexpected combination of interrupt action handler flags. However,
on at91 a timer IRQ is shared with some other devices (including
system wakeup ones) and that leads to the unusual combination of
flags in question.
To make it possible to avoid the warning introduce a new interrupt
action handler flag (which can be used by drivers to indicate the
special case to the core) and rework the problematic at91 drivers
to use it and work as expected during system suspend/resume. From
Boris Brezillon, Rafael J Wysocki and Mark Rutland.
- Clean up the generic power domains subsystem's debugfs interface
(Kevin Hilman)"
* tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
genirq / PM: describe IRQF_COND_SUSPEND
tty: serial: atmel: rework interrupt and wakeup handling
watchdog: at91sam9: request the irq with IRQF_NO_SUSPEND
cpuidle / sleep: Use broadcast timer for states that stop local timer
clk: at91: implement suspend/resume for the PMC irqchip
rtc: at91rm9200: rework wakeup and interrupt handling
rtc: at91sam9: rework wakeup and interrupt handling
PM / wakeup: export pm_system_wakeup symbol
genirq / PM: Add flag for shared NO_SUSPEND interrupt lines
ACPI / video: Propagate the error code for acpi_video_register
ACPI / video: Load the module even if ACPI is disabled
PM / Domains: cleanup: rename gpd -> genpd in debugfs interface
cpufreq: ppc: Add missing #include <asm/smp.h>
x86/PCI/ACPI: Relax ACPI resource descriptor checks to work around BIOS bugs
x86/PCI/ACPI: Ignore resources consumed by host bridge itself
cpuidle: Clean up fallback handling in cpuidle_idle_call()
cpuidle / sleep: Do sanity checks in cpuidle_enter_freeze() too
idle / sleep: Avoid excessive disabling and enabling interrupts
PCI: versatile: Update for list_for_each_entry() API change
genirq / PM: better describe IRQF_NO_SUSPEND semantics
With certain restrictions it is possible for a wakeup device to share
an IRQ with an IRQF_NO_SUSPEND user, and the warnings introduced by
commit cab303be91 are spurious. The new
IRQF_COND_SUSPEND flag allows drivers to tell the core when these
restrictions are met, allowing spurious warnings to be silenced.
This patch documents how IRQF_COND_SUSPEND is expected to be used,
updating some of the text now made invalid by its addition.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU9uKaAAoJEAf03oE53VmQrT4IAID5RZZLycH65MfI2SWs5jHJ
riXpp2ByX2YMZhBV7Y+jSJcdty0zdZFXAm3cME8YtHSHFNW87y3U90BhL1JTwFh8
Rlk45xxauRmiH5R+0haBIavt+ZFHB8QOgmAE+xa4Vc/qBiry6HSgWVldk3yiai5j
Mnq/+UpeL7mSlcn9kFkbVVOkDiP2tRoITU0z780tBgywbUQEluNZan4MfjSaknzP
GEwmN74Z6QPUxhqc1Z1ACU84ozYcLYaiMksNXrTch0+dLz91MIRl6Eqb53XhJEK3
P8ysCj16UBgX2JuuYWBGkxrZ1Brl0Lj5075JrM+He0T/XRsLTChb+9rQ14QrKno=
=YpBm
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "First fixes batch for AT91 on 4.0" from Nicolas Ferre:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: keep watchdog running in idle mode
dts: Documentation: AT91 Watchdog, explain what atmel,idle-halt property really do
ARM: at91/defconfig: add at91rm9200 ethernet support
ARM: at91/defconfig: remove CONFIG_SYSFS_DEPRECATED
ARM: at91/dt: at91sam9260: fix usart pinctrl
ARM: at91/dt: sama5d4: add missing alias for i2c0
ARM: at91/dt: at91sam9263: Fixup sram1 device tree node
ARM: at91: pm: fix SRAM allocation
ARM: at91: pm: fix at91rm9200 standby
pm: at91: Workaround DDRSDRC self-refresh bug with LPDDR1 memories.
pm: at91: pm_slowclock: fix suspend/resume hang up in timeouts
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gbWq
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung tmu and hdmi regression fixes for v4.0" from Kukjin Kim:
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
* tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add display power domain for exynos5250
ARM: dts: add 'hdmi' clock to mixer nodes for exynos5250 and exynos5420
ARM: dts: enable hdmi support for exynos4210-universal_c210
ARM: dts: enable hdmi support for exynos4412-odroid-common
ARM: dts: add dependency between TV and LCD0 power domains for exynos4
ARM: dts: add hdmi related nodes for exynos4 SoCs
ARM: EXYNOS: add support for sub-power domains
dt-bindings: document a note about power domain subdomains
ARM: dts: Provide dt bindings identical for Exynos TMU
ARM: dts: Trip points and sensor configuration data for exynos5440
ARM: dts: define default thermal-zones for exynos4
ARM: dts: default trip points definition for exynos5420
ARM: dts: add TMU default definitions for exynos4412
ARM: dts: Adding CPU cooling binding for Exynos SoCs
ARM: dts: Enable TMU for exynos4412-odriod-common
ARM: dts: Add LDO10 for TMU for exynos4412-odroid-common
ARM: dts: Enable TMU for exynos4210-trats
atmel,idle-halt property should be used with care, it actually makes the
watchdog not counting when the CPU is in idle state, therefore the
watchdog reset time depends on mean CPU usage and will not reset at all
of the CPU stop working while it is in idle state, which is probably not
what you want.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
PATA(pata_arasan_cf.c) and SDHCI(sdhci-of-arasan.c) drivers
are already using this prefix.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The memcg control knobs indicate the highest possible value using the
symbolic name "infinity", which is long and awkward to type.
Switch to the string "max", which is just as descriptive but shorter and
sweeter.
This changes a user interface, so do it before the release and before
the development flag is dropped from the default hierarchy.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We (the Ocfs2 project) recently moved the location of our ocfs2-tools
git tree and project web page. The pertinent discussion can be seen
here:
https://oss.oracle.com/pipermail/ocfs2-devel/2015-February/010579.html
The following patch updates the Ocfs2 documentation in MAINTAINERS,
ocfs2.txt, and dlmfs.txt. I added our new official web page, changed
the location of our tools git tree and removed the link to Joel's
ancient kernel git tree - Andrew has handled our patches for a while
now.
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This file provides a basic guide for how to handle conflict resolution
when it comes up in the development process.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Arjan van de Ven <arjanvandeven@gmail.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Ball <chris@printf.net>
Acked-by: Chris Mason <clm@fb.com>
Acked-by: Chris Metcalf <cmetcalf@ezchip.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: NeilBrown <neilb@suse.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Willy Tarreau <w@1wt.eu>
Acked-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for making one power domain a sub-domain of
other domain. This is useful for modeling power dependences for devices
like TV Mixer or Camera ISP, which needs to have more than one power
domain enabled to be operational.
Based on previous work by Amit Daniel Kachhap <amit.daniel@samsung.com>.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds a note on defining subdomains to generic PM domain
binding documentation to let power domain providers use common approach
for defining power domain hierarchy.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The IRQF_NO_SUSPEND flag is intended to be used for interrupts required
to be enabled during the suspend-resume cycle. This mostly consists of
IPIs and timer interrupts, potentially including chained irqchip
interrupts if these are necessary to handle timers or IPIs. If an
interrupt does not fall into one of the aforementioned categories,
requesting it with IRQF_NO_SUSPEND is likely incorrect.
Using IRQF_NO_SUSPEND does not guarantee that the interrupt can wake the
system from a suspended state. For an interrupt to be able to trigger a
wakeup, it may be necessary to program various components of the system.
In these cases it is necessary to use {enable,disabled}_irq_wake.
Unfortunately, several drivers assume that IRQF_NO_SUSPEND ensures that
an IRQ can wake up the system, and the documentation can be read
ambiguously w.r.t. this property.
This patch updates the documentation regarding IRQF_NO_SUSPEND to make
this caveat explicit, hopefully making future misuse rarer. Cleanup of
existing misuse will occur as part of later patch series.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PHY requires different settings for the Decision Feedback Analyzer
(DFE) when running in KX mode vs. KR mode. Update the code to change
these settings when changing modes in order to provide a more stable
link.
Additionally, adjust the 10GbE PQ skew default setting to a more sane
value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more vfs updates from Al Viro:
"Assorted stuff from this cycle. The big ones here are multilayer
overlayfs from Miklos and beginning of sorting ->d_inode accesses out
from David"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits)
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
Documentation/filesystems/Locking: ->get_sb() is long gone
trylock_super(): replacement for grab_super_passive()
fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
SELinux: Use d_is_positive() rather than testing dentry->d_inode
Smack: Use d_is_positive() rather than testing dentry->d_inode
TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
VFS: Split DCACHE_FILE_TYPE into regular and special types
VFS: Add a fallthrough flag for marking virtual dentries
VFS: Add a whiteout dentry type
VFS: Introduce inode-getting helpers for layered/unioned fs environments
Infiniband: Fix potential NULL d_inode dereference
posix_acl: fix reference leaks in posix_acl_create
autofs4: Wrong format for printing dentry
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
to changes that enable effective use of an unbound workqueue across
all available CPUs. A large battery of tests were performed to
validate these changes, summary of results is available here:
https://www.redhat.com/archives/dm-devel/2015-February/msg00106.html
- A few additional stable fixes (to DM core, dm-snapshot and dm-mirror)
and a small fix to the dm-space-map-disk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU51MsAAoJEMUj8QotnQNan8wH/3Oa2/ofbX8zNYtdDxFBK7W0
pHwVA2CH9yzDDi90X9GsQODmXerMrYf+SHo/RsQTpSnt5WI/4ZVP/1EoNGu6T2Yr
XiaKc/Jwo+ScxdhoHSNtyGL5vKeipX6clgz1wcd/4/UBcBAr0Vxj25s8Ta7naK2V
hZyWnt3MCGEDQ45NVBmLOU78Cl68LGf8JOUY0l3cd8ehQjGyR9a12GXwRktepslp
hw9xu8uYmE93fD+MIe/fUs7W/WvIVgFSskhswlvD3kAFpEAsMczjLGVSRQlBE90L
OK7v1HKxiIUJa17g3LmiCFa59ZjrnSHGpOOv9IPAFU/LzFIU47lcFwRFjgfB8po=
=8vFi
-----END PGP SIGNATURE-----
Merge tag 'dm-3.20-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull more device mapper changes from Mike Snitzer:
- Significant dm-crypt CPU scalability performance improvements thanks
to changes that enable effective use of an unbound workqueue across
all available CPUs. A large battery of tests were performed to
validate these changes, summary of results is available here:
https://www.redhat.com/archives/dm-devel/2015-February/msg00106.html
- A few additional stable fixes (to DM core, dm-snapshot and dm-mirror)
and a small fix to the dm-space-map-disk.
* tag 'dm-3.20-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm snapshot: fix a possible invalid memory access on unload
dm: fix a race condition in dm_get_md
dm crypt: sort writes
dm crypt: add 'submit_from_crypt_cpus' option
dm crypt: offload writes to thread
dm crypt: remove unused io_pool and _crypt_io_pool
dm crypt: avoid deadlock in mempools
dm crypt: don't allocate pages for a partial request
dm crypt: use unbound workqueue for request processing
dm io: reject unsupported DISCARD requests with EOPNOTSUPP
dm mirror: do not degrade the mirror on discard error
dm space map disk: fix sm_disk_count_is_more_than_one()
Pull more input updates from Dmitry Torokhov:
"The second round of updates for the input subsystem.
Updates to ALPS an bfin_roraty drivers and a couple oother fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - use IS_ENABLED instead of homegrown code
Input: bfin_rotary - introduce open and close methods
Input: bfin_rotary - convert to use managed resources
Input: bfin_rotary - use generic IO functions
Input: bfin_rotary - move pin lists into into platform data
Input: bfin_rotary - move platform header to linux/platform_data
Input: bfin_rotary - mark suspend and resume code as __maybe_unused
Input: bfin_rotary - fix potential oops in interrupt handler
Input: ALPS - move v7 packet info to Documentation and v6 packet info
Input: ALPS - fix confusing comment in protocol data
Input: ALPS - do not mix trackstick and external PS/2 mouse data
Input: ALPS - fix trackstick detection on some Dell Latitudes
Input: ALPS - consolidate setting protocol parameters
Input: ALPS - split protocol data from model info
Input: ALPS - make Rushmore a separate protocol
Input: ALPS - renumber protocol numbers
Input: adi - remove an unnecessary check
Input: pxa27x_keypad - remove an unneeded NULL check
Input: soc_button_array - use "Windows" key for "Home"
Pull i2c updates from Wolfram Sang:
"Summary:
- legacy PM code removed from the core, there were no users anymore
(thanks to Lars-Peter Clausen)
- new driver for Broadcom iProc
- bigger driver updates for designware, rk3x, cadence, ocores
- a bunch of smaller updates and bugfixes"
* 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (31 commits)
i2c: ocores: rework clk code to handle NULL cookie
i2c: designware-baytrail: another fixup for proper Kconfig dependencies
i2c: fix reference to functionality constants definition
i2c: iproc: Add Broadcom iProc I2C Driver
i2c: designware-pci: update Intel copyright line
i2c: ocores: add common clock support
i2c: hix5hd2: add COMPILE_TEST
i2c: clarify comments about the dev_released completion
i2c: ocores: fix clock-frequency binding usage
i2c: tegra: Maintain CPU endianness
i2c: designware-baytrail: use proper Kconfig dependencies
i2c: designware: Do not calculate SCL timing parameters needlessly
i2c: do not try to load modules for of-registered devices
i2c: designware: Add Intel Baytrail PMIC I2C bus support
i2c: designware: Add i2c bus locking support
of: i2c: Add i2c-mux-idle-disconnect DT property to PCA954x mux driver
i2c: designware: use {readl|writel}_relaxed instead of readl/writel
i2c: designware-pci: no need to provide clk_khz
i2c: designware-pci: remove Moorestown support
i2c: imx: whitespace and checkpatch cleanup
...
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Pull misc x86 fixes from Ingo Molnar:
"This contains:
- EFI fixes
- a boot printout fix
- ASLR/kASLR fixes
- intel microcode driver fixes
- other misc fixes
Most of the linecount comes from an EFI revert"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/ASLR: Avoid PAGE_SIZE redefinition for UML subarch
x86/microcode/intel: Handle truncated microcode images more robustly
x86/microcode/intel: Guard against stack overflow in the loader
x86, mm/ASLR: Fix stack randomization on 64-bit systems
x86/mm/init: Fix incorrect page size in init_memory_mapping() printks
x86/mm/ASLR: Propagate base load address calculation
Documentation/x86: Fix path in zero-page.txt
x86/apic: Fix the devicetree build in certain configs
Revert "efi/libstub: Call get_memory_map() to obtain map and desc sizes"
x86/efi: Avoid triple faults during EFI mixed mode calls
* KDB: improved searching
* No longer enter debug core on panic if panic timeout is set
KGDB/KDB regressions / cleanups
* fix pdf doc build errors
* prevent junk characters on kdb console from printk levels
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TH0R
-----END PGP SIGNATURE-----
Merge tag 'for_linux-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull kgdb/kdb updates from Jason Wessel:
"KGDB/KDB New:
- KDB: improved searching
- No longer enter debug core on panic if panic timeout is set
KGDB/KDB regressions / cleanups
- fix pdf doc build errors
- prevent junk characters on kdb console from printk levels"
* tag 'for_linux-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kgdb, docs: Fix <para> pdfdocs build errors
debug: prevent entering debug mode on panic/exception.
kdb: Const qualifier for kdb_getstr's prompt argument
kdb: Provide forward search at more prompt
kdb: Fix a prompt management bug when using | grep
kdb: Remove stack dump when entering kgdb due to NMI
kdb: Avoid printing KERN_ levels to consoles
kdb: Fix off by one error in kdb_cpu()
kdb: fix incorrect counts in KDB summary command output
- Use of_irq_init() to initialize interrupt controllers
- Get rid of some unlikely()
- Add CIB to support SATA and other interrupts
- Add support for CIU SUM2 interrupt sources
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Leonid Rosenboim <lrosenboim@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Peter Swain <peter.swain@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8947/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull more thermal managament updates from Zhang Rui:
"Specifics:
- Exynos thermal driver refactoring. Several cleanups, code
optimization, unused symbols removal, and unused feature removal in
Exynos thermal driver. Thanks Lukasz for this effort.
- Exynos thermal driver support to OF thermal. After the code
refactoring, the driver earned the support to OF thermal. Chip
thermal data were moved from driver code to DTS, reducing the code
footprint. Thanks Lukasz for this.
- After receiving the OF thermal support, the exynos thermal driver
now must allow modular build. Thanks Arnd for detecting, reporting
and fixing this.
- Exynos thermal driver support to Exynos 7 SoC. Thanks Abhilash for
this.
- Accurate temperature reporting on Rockchip thermal driver, thanks
to Caesar.
- Fix on how OF thermal enables its zones, thanks Lukasz for fixing.
- Fixes in OF thermal examples under Documentation/. Thanks Srinivas
for fixing"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: exynos: Add TMU support for Exynos7 SoC
dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
cpufreq: exynos: allow modular build
thermal: Fix examples in DT documentation
thermal: exynos: Correct sanity check at exynos_report_trigger() function
thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
thermal: exynos: Remove exynos_tmu_data.c file
thermal: rockchip: make temperature reporting much more accurate
thermal: exynos: Remove exynos_thermal_common.[c|h] files
thermal: samsung: core: Exynos TMU rework to use device tree for configuration
dts: Documentation: Update exynos-thermal.txt example for Exynos5440
dts: Documentation: Extending documentation entry for exynos-thermal
cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
thermal: exynos: cosmetic: Correct comment format
thermal: of: Enable thermal_zoneX when sensor is correctly added
toshiba_acpi: Add support for missing features from the Windows driver,
bump the sysfs version, and clean up the driver.
thinkpad_acpi: BIOS string versions, unhandled hkey events.
samsung-laptop: Add native backlight quirk, enable better lid handling.
intel_scu_ipc: Read resources from PCI configuration
other: Fix sparse warnings, general cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU5Xg2AAoJEKbMaAwKp364WaUH/Akf1jrGGaC8czGVsvAz4syV
jV+4yHA1z/E1sy1LjS7gKxpaYO5j5a6Nv0488kaM/RPZoVPSXgGsrCS/HPjpRJIR
90PGQuZ3gUWpqt6ICqjs22fHVQ/k0NF7uiLgqOsACnLWAN7ts3GXNs6CLpzlwhQY
+YXzw3ac1QeB3lSKYxTmRKRZ9qCoHBmONSG/DzyHw8cmXI9LuSd7LCs8BHsg3M1v
/WYJlLTJRgS5POfPenWoW1GQ0tN9OgC19Hk4dtFMv0U1s6au7z0a8rFqHc0qR18b
tMkf9/8kaatTrKLlWhxX2/Wyenu8wpVjSYvRrRHsMCJRaWHyQQStd3Lhvw0Kzyg=
=W5L5
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v3.20-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull platform driver update from Darren Hart:
"This includes a significant update to the toshiba_acpi driver,
bringing it to feature parity with the Windows driver, followed by
some needed cleanups.
The other changes are mostly minor updates, quirks, sparse fixes, or
cleanups.
Details:
- toshiba_acpi:
Add support for missing features from the Windows driver, bump the
sysfs version, and clean up the driver.
- thinkpad_acpi:
BIOS string versions, unhandled hkey events.
- msamsung-laptop:
Add native backlight quirk, enable better lid handling.
- intel_scu_ipc:
Read resources from PCI configuration
- other:
Fix sparse warnings, general cleanups"
* tag 'platform-drivers-x86-v3.20-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (34 commits)
toshiba_acpi: Cleanup GPL header
toshiba_acpi: Cleanup comment blocks and capitalization
toshiba_acpi: Make use of DEVICE_ATTR_{RO, RW} macros
toshiba_acpi: Drop the toshiba_ prefix from sysfs function names
toshiba_acpi: Move sysfs function and struct declarations further down
Documentation/ABI: Add file describing the sysfs entries for toshiba_acpi
toshiba_acpi: Clean file according to coding style
toshiba_acpi: Bump version number to 0.21
toshiba_acpi: Add support to enable/disable USB 3
toshiba_acpi: Add support for Panel Power ON
toshiba_acpi: Add support for Keyboard functions mode
toshiba_acpi: Add fan entry to sysfs
toshiba_acpi: Add version entry to sysfs
thinkpad_acpi: support new BIOS version string pattern
thinkpad_acpi: unhandled hkey event
toshiba_acpi: Make toshiba_eco_mode_available more robust
classmate-laptop: Fix sparse warning (0 as NULL)
Sony-laptop: Fix sparse warning (make undeclared var static)
thinkpad_acpi.c: Fix sparse warning (make undeclared var static)
samsung-laptop.c: Prefer kstrtoint over single variable sscanf
...
kgdb.pdf failed to build from 'make pdfdocs' giving errors such as:
jade:... Documentation/DocBook/kgdb.xml:200:8:E:
document type does not allow element "para" here; missing one of
"footnote", "caution", "important", "note", "tip", "warning",
"blockquote", "informalexample" start-tag
Fixing minor <para> and <sect> issues allows kgdb.pdf to be generated
under Fedora20.
Originally submitted by rajaneesh.acharya@yahoo.com in 2011, discussed here:
http://permalink.gmane.org/gmane.linux.documentation/3954
as patch:
The following are the enhancements that removed the errors
while issuing "make pdfdocs"
[graham.whaley@intel.com: Improved commit message and ported to 3.18.1]
Signed-off-by: Graham Whaley <graham.whaley@intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull misc kbuild changes from Michal Marek:
"Just a few non-critical kbuild changes:
- builddeb adds the actual distribution name in the changelog
- documentation fixes"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: trivial - fix the help doc of CONFIG_CC_OPTIMIZE_FOR_SIZE
kbuild: Update documentation of clean-files and clean-dirs
builddeb: Try to determine distribution
builddeb: Update year and git repository URL in debian/copyright
