In striding RQ mode, the buffers of an RX WQE are first
prepared and posted to the HW using a UMR WQEs via the ICOSQ.
We maintain the state of these in-progress WQEs in the RQ
SW struct.
In the flow of ICOSQ recovery, the corresponding RQ is not
in error state, hence:
- The buffers of the in-progress WQEs must be released
and the RQ metadata should reflect it.
- Existing RX WQEs in the RQ should not be affected.
For this, wrap the dealloc of the in-progress WQEs in
a function, and use it in the ICOSQ recovery flow
instead of mlx5e_free_rx_descs().
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When resetting the RQ (moving RQ state from RST to RDY), the driver
resets the WQ's SW metadata.
In striding RQ mode, we maintain a field that reflects the actual
expected WQ head (including in progress WQEs posted to the ICOSQ).
It was mistakenly not reset together with the WQ. Fix this here.
Fixes: 8276ea1353 ("net/mlx5e: Report and recover from CQE with error on RQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add number of WQEBBs (WQE's Basic Block) to WQE info struct. Set the
number of WQEBBs on WQE post, and increment the consumer counter (cc)
on completion.
In case of error completions, the cc was mistakenly not incremented,
keeping a gap between cc and pc (producer counter). This failed the
recovery flow on the ICOSQ from a CQE error which timed-out waiting for
the cc and pc to meet.
Fixes: be5323c837 ("net/mlx5e: Report and recover from CQE error on ICOSQ")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cap_mask1 isn't protected by field_select and not listed among RW
fields, but it is required to be written to properly initialize ports
in IB virtualization mode.
Link: https://lore.kernel.org/linux-rdma/88bab94d2fd72f3145835b4518bc63dda587add6.camel@redhat.com
Fixes: ab118da4c1 ("net/mlx5: Don't write read-only fields in MODIFY_HCA_VPORT_CONTEXT command")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
checkpatch found a lack of appropriate whitespace after certain keywords
as per the style guide. Add it in.
Signed-off-by: Logan Magee <mageelog@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c: In function nicvf_sq_free_used_descs:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c:1182:12: warning:
variable tail set but not used [-Wunused-but-set-variable]
It's not used since commit 4863dea3fab01("net: Adding support for Cavium ThunderX network controller"),
so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng zengkai <zhengzengkai@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code ignores the return value from
bnxt_hwrm_func_backing_store_cfg(), causing the driver to proceed in
the init path even when this vital firmware call has failed. Fix it
by propagating the error code to the caller.
Fixes: 1b9394e5a2 ("bnxt_en: Configure context memory on new devices.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocated ieee_ets structure goes out of scope without being freed,
leaking memory. Appropriate result codes should be returned so that
callers do not rely on invalid data passed by reference.
Also cache the ETS config retrieved from the device so that it doesn't
need to be freed. The balance of the code was clearly written with the
intent of having the results of querying the hardware cached in the
device structure. The commensurate store was evidently missed though.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an indexing bug in determining these ethtool priority
counters. Instead of using the queue ID to index, we need to
normalize by modulo 10 to get the index. This index is then used
to obtain the proper CoS queue counter. Rename bp->pri2cos to
bp->pri2cos_idx to make this more clear.
Fixes: e37fed7903 ("bnxt_en: Add ethtool -S priority counters.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet trap groups are now explicitly registered by drivers and not
implicitly registered when the packet traps are registered. Therefore,
there is no need to encode entire group structure the trap is associated
with inside the trap structure.
Instead, only pass the group identifier. Refer to it as initial group
identifier, as future patches will allow user space to move traps
between groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the previously added API to explicitly register / unregister
supported packet trap groups. This is in preparation for future patches
that will enable drivers to pass additional group attributes, such as
associated policer identifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far only the reset bit it set, but the handler executing the reset
is not scheduled. Therefore nothing will happen until some other action
schedules the handler. Improve this by ensuring that the handler is
scheduled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation makes the implicit assumption that if a bit
is set, then the work is scheduled already. Remove the need for this
implicit assumption and call schedule_work() always. It will check
internally whether the work is scheduled already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently rtl_task() is designed to handle a large number of tasks.
However we have just one, so we can remove some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out setting GPHY 10M to new helper rtl8168g_enable_gphy_10m.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-03-21
Implement basic support for the devlink interface in the ice driver.
Additionally pave some necessary changes for adding a devlink region that
exposes the NVM contents.
This series first contains 5 patches for enabling and implementing full NVM
read access via the ETHTOOL_GEEPROM interface. This includes some cleanup of
endian-types, a new function for reading from the NVM and Shadow RAM as a flat
addressable space, a function to calculate the available flash size during
load, and a change to how some of the NVM version fields are stored in the
ice_nvm_info structure.
Following this is 3 patches for implementing devlink support. First, one patch
which implements the basic framework and introduces the ice_devlink.c file.
Second, a patch to implement basic .info_get support. Finally, a patch which
reads the device PBA identifier and reports it as the `board.id` value in the
.info_get response.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes wrapper fn()s around mutex_init/lock/unlock.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed MODULE_VERSION and fixed MODULE_AUTHOR.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With MTU sized receive buffers it is not expected to have CQE_RX
with multiple receive buffer pointers. But since same physcial link
is shared by PF and it's VFs, the max receive packet configured
at link could be morethan MTU. Hence there is a chance of receiving
plts morethan MTU which then gets DMA'ed into multiple buffers
and notified in a single CQE_RX. This patch treats such pkts as errors
and frees up receive buffers pointers back to hardware.
Also on the transmit side this patch sets SMQ MAXLEN to max value to avoid
HW length errors for the packets whose size > MTU, eg due to path MTU.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF shares physical link with PF. Admin function (AF) sends
notification to PF whenever a link change event happens. PF
has to forward the same notification to each of the enabled VF.
PF traps START/STOP_RX messages sent by VF to AF to keep track of
VF's enabled/disabled state.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added ethtool support for VF devices for
- Driver stats, Tx/Rx perqueue stats
- Set/show Rx/Tx queue count
- Set/show Rx/Tx ring sizes
- Set/show IRQ coalescing parameters
- RSS configuration etc
It's the PF which owns the interface, hence VF
cannot display underlying CGX interface stats.
Except for this rest ethtool support reuses PF's
APIs.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On OcteonTx2 silicon there two two types VFs, VFs that share the
physical link with their parent SR-IOV PF and the VFs which work
in pairs using internal HW loopback channels (LBK). Except for the
underlying Rx/Tx channel mapping from netdev functionality perspective
they are almost identical. This patch adds netdev driver support
for these VFs.
Unlike it's parent PF a VF cannot directly communicate with admin
function (AF) and it has to go through PF for the same. The mailbox
communication with AF works like 'VF <=> PF <=> AF'.
Also functionality wise VF and PF are identical, hence to avoid code
duplication PF driver's APIs are resued here for HW initialization,
packet handling etc etc ie almost everything. For VF driver to compile
as module exported few of the existing PF driver APIs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When FLR is initiated for a VF (PCI function level reset),
the parent PF gets a interrupt. PF then sends a message to
admin function (AF), which then cleanups all resources attached
to that VF.
Also handled IRQs triggered when master enable bit is cleared
or set for VFs. This handler just clears the transaction pending
ie TRPEND bit.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added 'sriov_configure' to enable/disable virtual functions (VFs).
Also added handling of mailbox messages from these VFs.
Admin function (AF) is the only one with all priviliges to configure
HW, alloc resources etc etc, PFs and it's VFs have to request AF
via mbox for all their needs. But unlike PFs, their VFs cannot
send a mbox request directly. A VF shares a mailbox region with
it's parent PF, so VF sends a mailbox msg to PF and then PF forwards
it to AF. Then AF after processing sends response to PF which it
again forwards to VF.
This patch adds support for this 'VF <=> PF <=> AF' mailbox
communication.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building arm32 allyesconfig:
ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by spectrum_cnt.c
>>> net/ethernet/mellanox/mlxsw/spectrum_cnt.o:(mlxsw_sp_counter_resources_register) in archive drivers/built-in.a
>>> did you mean: __aeabi_uidivmod
>>> defined in: arch/arm/lib/lib.a(lib1funcs.o)
pool_size and bank_size are u64; use div64_u64 so that 32-bit platforms
do not error.
Fixes: ab8c4cc604 ("mlxsw: spectrum_cnt: Move config validation along with resource register")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 53eca1f347 ("net: rename flow_action_hw_stats_types* ->
flow_action_hw_stats*") renamed just the flow action types and
helpers. For consistency rename variables, enums, struct members
and UAPI too (note that this UAPI was not in any official release,
yet).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl5hh6wACgkQSD+KveBX
+j6qvQf9HQsiQ+cE1UIbM/IzyTWXeBMzjljCWFgQfvyKQjSFnoATeVl6GMQJNk7M
ovQ7XHOlN36E/tQW/ypnwbX+btjl/mDEJsxEcvVf4gnw/QH1AwUjo291vPfrE5md
DcWWe9Jrq2MkHeZAgIt/Tnw4GYIwQOBVmYgky3A0+azzuvxK+nXX6JJG5JqRR8Wd
tBsN9UKok1nOt73d+TyHjGnzQHWzGBdS0vlxl0MYcD1QD66UzA0Atgz5aUQLGvTK
Nk/IcHr3SF+0kvbtpjRxlrpi4ywD2gBNHXMJX1DDnCkqg9nWjJ5DByYDASo+I6uL
0fMNsimp/gZG8HD0oFEVTFgaqPACUA==
=DEqe
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-03-05
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v5.4
('net/mlx5: DR, Fix postsend actions write length')
For -stable v5.5
('net/mlx5e: kTLS, Fix TCP seq off-by-1 issue in TX resync flow')
('net/mlx5e: Fix endianness handling in pedit mask')
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit ed0a72e0de ("net/freescale: Clean drivers from static versions")
leave behind this, remove it .
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PF responds to VF depending on what mailbox it is
handling, it is a bit inflexible. The correct way is, PF should
check the mbx_need_resp field to decide whether gives response
to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For making the code more readable, this adds several new
structure to replace the msg field in structure
hclge_mbx_vf_to_pf_cmd and hclge_mbx_pf_to_vf_cmd.
Also uses macro to instead of some magic number.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when mailbox handling fails, the PF driver
just responds 1 to the VF driver. It is not sufficient
for the VF driver to find out why its mailbox fails.
So the error should be responded to VF, but the error
is type int and the response field in struct
hclge_mbx_pf_to_vf_cmd is type u16, a conversion is
needed.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware offloading of the NETIF_F_HW_CSUM and NETIF_F_RXCSUM
features requires the use of Transmit Status Blocks before transmit
frame data and Receive Status Blocks before receive frame data to
carry the checksum information.
Unfortunately, these status blocks are currently only enabled when
the NETIF_F_HW_CSUM feature is enabled. As a result NETIF_F_RXCSUM
will not actually be offloaded to the hardware unless both it and
NETIF_F_HW_CSUM are enabled. Fortunately, that is the default
configuration.
This commit addresses this issue by always enabling the use of
status blocks on both transmit and receive frames. Further, it
replaces the use of a dedicated flag within the driver private
data structure with direct use of the netdev features flags.
Fixes: 8101553978 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we clean up devicetree related configuration
also when clock init fails.
Fixes: fecd4d7eef ("net: stmmac: dwmac-rk: Add integrated PHY support")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the queue structs exist before trying to tear
them down to make for safer error recovery.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a little more cleanup when tearing down the queues.
Fixes: 1d062b7b6f ("ionic: Add basic adminq support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't worry if the rx filter add firmware request fails on
EEXIST, at least we know the filter is there. Same for
the delete request, at least we know it isn't there.
Fixes: 2a654540be ("ionic: Add Rx filter and rx_mode ndo support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't save the lif->dentry until we know we have
a good value.
Fixes: 1a58e19646 ("ionic: Add basic lif support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible (but unlikely) that FW was busy and missed a heartbeat
check but is still alive and will process the pending request, so don't
clean the dev_cmd in this case. This occasionally occurs when working
with a card that is supporting many devices and is trying to shut them
all down at once, but still wants to see that last LIF disable request.
Fixes: 97ca486592 ("ionic: add heartbeat check")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Short circuit the cleanup if we get a timeout error from
ionic_qcq_disable() so as to not have to wait too long
on shutdown when we already know the FW is not responding.
Fixes: 0f3154e6bc ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Headers ionic_if.h and ionic_regs.h are licensed under three alternative
licenses and the used SPDX-License-Identifier expression makes
./scripts/spdxcheck.py complain:
drivers/net/ethernet/pensando/ionic/ionic_if.h: 1:52 Syntax error: OR
drivers/net/ethernet/pensando/ionic/ionic_regs.h: 1:52 Syntax error: OR
As OR is associative, it is irrelevant if the parentheses are put around
the first or the second OR-expression.
Simply add parentheses to make spdxcheck.py happy.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
the minimum value of skb len that hw supports is 32 rather than 17
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the second input parameter of wait_for_completion_timeout should
be jiffies instead of millisecond
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add read barrier in driver code to keep from reading other fileds
in dma memory which is writable for hw until we have verified the
memory is valid for driver
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
should disable eq irq before freeing it, must clear event queue
depth in hw before freeing relevant memory to avoid illegal
memory access and update consumer idx to avoid invalid interrupt
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it's unreliable for fw to check whether IO is stopped, so driver
wait for enough time to ensure IO process is done in hw before
freeing resources
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a unique board identifier using "board.id" for devlink's
.info_get command.
Obtain this by reading the NVM for the PBA identification string.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The devlink .info_get callback allows the driver to report detailed
version information. The following devlink versions are reported with
this initial implementation:
"fw.mgmt" -> The version of the firmware that controls PHY, link, etc
"fw.mgmt.api" -> API version of interface exposed over the AdminQ
"fw.mgmt.build" -> Unique build id of the source for the management fw
"fw.undi" -> Version of the Option ROM containing the UEFI driver
"fw.psid.api" -> Version of the NVM image format.
"fw.bundle_id" -> Unique identifier for the combined flash image.
"fw.app.name" -> The name of the active DDP package.
"fw.app" -> The version of the active DDP package.
With this, devlink dev info can report at least as much information as
is reported by ETHTOOL_GDRVINFO.
Compare the output from ethtool vs from devlink:
$ ethtool -i ens785s0
driver: ice
version: 0.8.1-k
firmware-version: 0.80 0x80002ec0 1.2581.0
expansion-rom-version:
bus-info: 0000:3b:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: yes
$ devlink dev info pci/0000:3b:00.0
pci/0000:3b:00.0:
driver ice
serial number 00-01-ab-ff-ff-ca-05-68
versions:
running:
fw.mgmt 2.1.7
fw.mgmt.api 1.5
fw.mgmt.build 0x305d955f
fw.undi 1.2581.0
fw.psid.api 0.80
fw.bundle_id 0x80002ec0
fw.app.name ICE OS Default Package
fw.app 1.3.1.0
More pieces of information can be displayed, each version is kept
separate instead of munged together, and each version has an identifier
which comes with associated documentation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The nfp driver uses ``fw.bundle_id`` to represent a unique identifier of the
entire firmware bundle.
A future change is going to introduce a similar notion in the ice
driver, so promote ``fw.bundle_id`` into a generic version now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Begin implementing support for the devlink interface with the ice
driver.
The pf structure is currently memory managed through devres, via
a devm_alloc. To mimic this behavior, after allocating the devlink
pointer, use devm_add_action to add a teardown action for releasing the
devlink memory on exit.
The ice hardware is a multi-function PCIe device. Thus, each physical
function will get its own devlink instance. This means that each
function will be treated independently, with its own parameters and
configuration. This is done because the ice driver loads a separate
instance for each function.
Due to this, the implementation does not enable devlink to manage
device-wide resources or configuration, as each physical function will
be treated independently. This is done for simplicity, as managing
a devlink instance across multiple driver instances would significantly
increase the complexity for minimal gain.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation of .get_eeprom only enables reading from the
Shadow RAM portion of the NVM contents. Implement support for reading
the entire flash contents instead of only the initial portion contained
in the Shadow RAM.
A complete dump can take several seconds, but the ETHTOOL_GEEPROM ioctl
is capable of reading only a limited portion at a time by specifying the
offset and length to read.
In order to perform the reads directly, several functions are made non
static. Additionally, the unused ice_read_sr_buf_aq and ice_read_sr_buf
functions are removed.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When reading from the NVM using a flat address, it is useful to know the
upper bound on the size of the flash contents. This value is not stored
within the NVM.
We can determine the size by performing a bisection between upper and
lower bounds. It is known that the size cannot exceed 16 MB (offset of
0xFFFFFF).
Use a while loop to bisect the upper and lower bounds by reading one
byte at a time. On a failed read, lower the maximum bound. On
a successful read, increase the lower bound.
Save this as the flash_size in the ice_nvm_info structure that contains
data related to the NVM.
The size will be used in a future patch for implementing full NVM read
via ethtool's GEEPROM command.
The maximum possible size for the flash is bounded by the size limit for
the NVM AdminQ commands. Add a new macro, ICE_AQC_NVM_MAX_OFFSET, which
can be used to represent this upper bound.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM version and Option ROM version information is stored within the
struct ice_nvm_ver_info structure. The data for the NVM is stored as
a 2byte value with the major and minor versions each using one byte from
the field. The Option ROM is stored as a 4byte value that contains
a major, build, and patch number.
Modify the code to immediately extract the version values and store them
in a new struct ice_orom_info. Remove the now unnecessary
ice_get_nvm_version function.
Update ice_ethtool.c to use the new fields directly from the structured
data.
This reduces complexity of the code that prints these versions in
ice_ethtool.c
Update the macro definitions and variable names to use the term "orom"
instead of "oem" for the Option ROM version. This helps increase the
clarity of the Option ROM version code.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM contents are read via firmware by using the ice_aq_read_nvm
function. This function has a couple of limits:
1) The AdminQ commands can only take buffers sized up to 4Kb. Thus, any
larger read must be split into multiple reads.
2) when reading from the Shadow RAM, reads must not cross sector
boundaries. The sectors are also 4Kb in size.
Implement the ice_read_flat_nvm function to read portions of the NVM by
flat offset. That is, to read using offsets from the start of the NVM
rather than from a specific module.
This function will be able to read both from the NVM and from the Shadow
RAM. For simplicity NVM reads will always be broken up to not cross 4Kb
page boundaries, even though this is not required unless reading from
the Shadow RAM.
Use this new function as the implementation of ice_read_sr_word_aq.
The ice_read_sr_buf_aq function is not modified here. This is because
a following change will remove the only caller of that function in favor
of directly using ice_read_flat_nvm. Thus, there is little benefit to
changing it now only to remove it momentarily. At the same time, the
ice_read_sr_aq function will also be removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ice_read_sr_aq function returns words in the Little Endian format.
Remove the need for __force and typecasting by using a local variable in
the ice_read_sr_word_aq function.
Additionally clarify explicitly that the ice_read_sr_aq function takes
storage for __le16 values instead of using u16.
Being explicit about the endianness of this data helps when using tools
like sparse to catch endian-related issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver reclaims descriptors in much smaller batches, even if hardware
indicates more to reclaim, during backpressure. So, fix the check to
restart the Txq during backpressure, by looking at how many
descriptors hardware had indicated to reclaim, and not on how many
descriptors that driver had actually reclaimed. Once the Txq is
restarted, driver will reclaim even more descriptors when Tx path
is entered again.
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
reverted back to getting Tx CIDX updates via DMA, instead of interrupts,
introduced by commit d429005fdf ("cxgb4/cxgb4vf: Add support for SGE
doorbell queue timer")
However, it missed reverting back several code changes where Tx CIDX
updates are not explicitly requested during backpressure when using
interrupt mode. These missed changes cause slow recovery during
backpressure because the corresponding interrupt no longer comes and
hence results in Tx throughput drop.
So, revert back these missed code changes, as well, which will allow
explicitly requesting Tx CIDX updates when backpressure happens.
This enables the corresponding interrupt with Tx CIDX update message
to get generated and hence speed up recovery and restore back
throughput.
Fixes: 7c3bebc3d8 ("cxgb4: request the TX CIDX updates to status page")
Fixes: d429005fdf ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload action skbedit priority when keyed to a flower classifier. The
skb->priority field in Linux is very generic, so only allow setting the
bottom 8 priorities and bounce anything else.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QOS_ACTION is used for manipulating the QoS attributes of a packet.
Add the corresponding defines and helpers, in particular for the
switch_priority override.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it will check the return value of dwmac_dma_reset() in the
stmmac_init_dma_engine() function and report an error if the
return value is not zero. so don't need check here.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_chip_specific_setup':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1378:8: warning:
variable 's' set but not used [-Wunused-but-set-variable]
It's not used since commit b6334be64d ("net/liquidio: Delete driver version assignment")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization the driver issues a software reset command and
then waits for the system status to change back to "ready" state.
However, before issuing the reset command the driver does not check that
the system is actually in "ready" state. On Spectrum-{1,2} systems this
was always the case as the hardware initialization time is very short.
On Spectrum-3 systems this is no longer the case. This results in the
software reset command timing-out and the driver failing to load:
[ 6.347591] mlxsw_spectrum3 0000:06:00.0: Cmd exec timed-out (opcode=40(ACCESS_REG),opcode_mod=0,in_mod=0)
[ 6.358382] mlxsw_spectrum3 0000:06:00.0: Reg cmd access failed (reg_id=9023(mrsr),type=write)
[ 6.368028] mlxsw_spectrum3 0000:06:00.0: cannot register bus device
[ 6.375274] mlxsw_spectrum3: probe of 0000:06:00.0 failed with error -110
Fix this by waiting for the system to become ready both before issuing
the reset command and afterwards. In case of failure, print the last
system status to aid in debugging.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Compiler warnings and cleanup for the connection tracking series
2) Bug fixes for the connection tracking series
3) Fix devlink port register sequence
4) Last five patches in the series, By Eli cohen
Add the support for forwarding traffic between two eswitch uplink
representors (Hairpin for eswitch), using mlx5 termination tables
to change the direction of a packet in hw from RX to TX pipeline.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl5ximgACgkQSD+KveBX
+j4iGwf9FrTxtGjgVXuwmc5LmSU6tak5SjK+dW5PdCw4mNorN2hSJeV/f9evLrf7
7Cxfm4OH8/ivOSpVQz6XZEF0aYTq9T3JakGzAWESWwo/s+i7iwA+lVPYKhcvHXeg
C9ImWbnyDCZkPZM6jz4KNpSMRWkyB7sEtQ51hYF0bdiSzcLSDaLCoKPEljp7sNKb
f1456/yDuOIZ3sb6rYPH6e8EqqfUMiyYAyY3bBu09sl3deXopyueYVqPSPgjOoC7
SfM5K+9nnuQJdvSqwUJLexxDZo1Z7fizz73LwUp0SBLk5zvZdn2bhxbt4wPS/xH/
CSjsWFAs1eu2rDqRH48G3jKqTZeq2w==
=LkML
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-03-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-03-17
1) Compiler warnings and cleanup for the connection tracking series
2) Bug fixes for the connection tracking series
3) Fix devlink port register sequence
4) Last five patches in the series, By Eli cohen
Add the support for forwarding traffic between two eswitch uplink
representors (Hairpin for eswitch), using mlx5 termination tables
to change the direction of a packet in hw from RX to TX pipeline.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement occupancy counting for counters and expose over devlink
resource API.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put all init operations related to subpools into
mlxsw_sp_counter_sub_pools_init().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the validation of subpools configuration, to avoid possible over
commitment to resource registration. Add WARN_ON to indicate bug
in the code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement devlink resources support for counter pools. Move the subpool
sizes calculations into the new resources register function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new field to subpool struct that would indicate which
resource id should be used to query the entry size for
the subpool from the device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the global static array of subpools is used. Make it
per-instance as multiple instances of the mlxsw driver can have
different values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bank size is different between Spectrum versions. Also it is
a resource that can be queried. So instead of hard coding the value in
code, query it from the firmware.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chelsio NICs have 3 filter regions, in following order of priority:
1. High Priority (HPFILTER) region (Highest Priority).
2. HASH region.
3. Normal FILTER region (Lowest Priority).
Currently, there's a 1-to-1 mapping between the prio value passed
by TC and the filter region index. However, it's possible to have
multiple TC rules with the same prio value. In this case, if a region
is exhausted, no attempt is made to try inserting the rule in the
next available region.
So, rework and remove the 1-to-1 mapping. Instead, dynamically select
the region to insert the filter rule, as long as the new rule's prio
value doesn't conflict with existing rules across all the 3 regions.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for Enterprise MAC IP version which is very similar to
XGMAC. It's so similar that we just need to check the device id and add
new speeds definitions and some minor callbacks.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XLGMII support for stmmac including the list of speeds and defines
for them.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
last_keep_alive_jiffies is updated in probe and when a keep-alive
event is received. In case the driver times-out on a keep-alive event,
it has high chances of continuously timing-out on keep-alive events.
This is because when the driver recovers from the keep-alive-timeout reset
the value of last_keep_alive_jiffies is very old, and if a keep-alive
event is not received before the next timer expires, the value of
last_keep_alive_jiffies will cause another keep-alive-timeout reset
and so forth in a loop.
Solution:
Update last_keep_alive_jiffies whenever the device is restored after
reset.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx req_id is an index in struct ena_eth_io_rx_cdesc_base.
The driver should validate that the Rx req_id it received from
the device is in range [0, ring_size -1]. Failure to do so could
yield to potential memory access violoation.
The validation was mistakenly done when refilling
the Rx submission queue and not in Rx completion queue.
Fixes: ad974baef2 ("net: ena: add support for out of order rx buffers refill")
Signed-off-by: Noam Dagan <ndagan@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug:
In short the main issue is caused by the fact that the number of queues
is changed using ethtool after ena_probe() has been called and before
ena_up() was executed. Here is the full scenario in detail:
* ena_probe() is called when the driver is loaded, the driver is not up
yet at the end of ena_probe().
* The number of queues is changed -> io_queue_count is changed as well -
ena_up() is not called since the "dev_was_up" boolean in
ena_update_queue_count() is false.
* ena_up() is called by the kernel (it's called asynchronously some
time after ena_probe()). ena_setup_io_intr() is called by ena_up() and
it uses io_queue_count to get the suitable irq lines for each msix
vector. The function ena_request_io_irq() is called right after that
and it uses msix_vecs - This value only changes during ena_probe() and
ena_restore() - to request the irq vectors. This results in "Failed to
request I/O IRQ" error for i > io_queue_count.
Numeric example:
* After ena_probe() io_queue_count = 8, msix_vecs = 9.
* The number of queues changes to 4 -> io_queue_count = 4, msix_vecs = 9.
* ena_up() is executed for the first time:
** ena_setup_io_intr() inits the vectors only up to io_queue_count.
** ena_request_io_irq() calls request_irq() and fails for i = 5.
How to reproduce:
simply run the following commands:
sudo rmmod ena && sudo insmod ena.ko;
sudo ethtool -L eth1 combined 3;
Fix:
Use ENA_MAX_MSIX_VEC(adapter->num_io_queues + adapter->xdp_num_queues)
instead of adapter->msix_vecs. We need to take XDP queues into
consideration as they need to have msix vectors assigned to them as well.
Note that the XDP cannot be attached before the driver is up and running
but in XDP mode the issue might occur when the number of queues changes
right after a reset trigger.
The ENA_MAX_MSIX_VEC simply adds one to the argument since the first msix
vector is reserved for management queue.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overview:
We don't frequently change the msix vectors throughout the life cycle of
the driver. We do so in two functions: ena_probe() and ena_restore().
ena_probe() is only called when the driver is loaded. ena_restore() on the
other hand is called during device reset / resume operations.
We use num_io_queues for calculating and allocating the number of msix
vectors. At ena_probe() this value is equal to max_num_io_queues and thus
this is not an issue, however ena_restore() might be called after the
number of io queues has changed.
A possible bug scenario is as follows:
* Change number of queues from 8 to 4.
(num_io_queues = 4, max_num_io_queues = 8, msix_vecs = 9,)
* Trigger reset occurs -> ena_restore is called.
(num_io_queues = 4, max_num_io_queues =8 , msix_vecs = 5)
* Change number of queues from 4 to 6.
(num_io_queues = 6, max_num_io_queues = 8, msix_vecs = 5)
* The driver will reset due to failure of check_for_rx_interrupt_queue()
Fix:
This can be easily fixed by always using max_num_io_queues to init the
msix_vecs, since this number won't change as opposed to num_io_queues.
Fixes: 4d19266022 ("net: ena: multiple queue creation related cleanups")
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't recognize the transceiver type, set the xcvr type
and data length such that ethtool can at least print the first
256 bytes and the reader can figure out why the transceiver
is not recognized.
While we're here, we can update the phy_id type values to use
the enum values in sfp.h.
Fixes: 4d03e00a21 ("ionic: Add initial ethtool support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the adminq's napi struct when tearing down
the adminq.
Fixes: 1d062b7b6f ("ionic: Add basic adminq support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't bother de-initing RSS if it wasn't selected.
Fixes: aa3198819b ("ionic: Add RSS support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't set a port type, the devlink code will eventually
print a WARN in the kernel log. Because the mgmt device is
not really a useful port, don't register it as a devlink port.
Fixes: b3f064e974 ("ionic: add support for device id 0x1004")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP flower offload uses delayed stats. Kernel recently gained
the ability to specify stats types. Make nfp accept DELAYED
stats, not just the catch all "any".
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked at least 5
cycles while the sw_reset is asserted to ensure a clean reset.
That commit enabled local loopback to provide an Rx clock from the
GENET sourced Tx clk. However, when connected in MII mode the Tx
clk is sourced by the PHY so if an EPHY is not supplying clocks
(e.g. when the link is down) the UniMAC does not receive the
necessary clocks.
This commit extends the sw_reset window until the PHY reports that
the link is up thereby ensuring that the clocks are being provided
to the MAC to produce a clean reset.
One consequence is that if the system attempts to enter a Wake on
LAN suspend state when the PHY link has not been active the MAC
may not have had a chance to initialize cleanly. In this case, we
remove the sw_reset and enable the WoL reception path as normal
with the hope that the PHY will provide the necessary clocks to
drive the WoL blocks if the link becomes active after the system
has entered suspend.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3a55402c93.
This is not a good solution when connecting to an external switch
that may not support the isolation of the TXC signal resulting in
output driver contention on the pin.
A different solution is necessary.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters.
While at it remove unnecessary zeroing on get.
No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
The check for use_adaptive_tx_coalesce will now be done by
the core.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e1f550dc44.
platform_get_irq_optional() will still return -ENXIO when no interrupt
is provided so the additional error handling caused the driver prone to
fail when no interrupt was specified. Revert the change so we can apply
the correct minimal fix.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not allow forwarding of encapsulated traffic received from one eswtich's
uplink to another eswtich's uplink.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add dependencny on cap termination_table_raw_traffic to allow non
encapsulated packets received from uplink to be forwarded back to the
received uplink port.
Refactor the conditions into a separate function.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Termination tables change the direction of a packet in hw from RX to SX
pipeline. Use that to offload hairpin flows received from uplink and
sent back to uplink.
Currently termination tables are used for pushing VLAN to packets
received from uplink and targeting a VF. Extend the implementation to
allow forwarding packets to uplink. These packets can either be
encapsulated or not.
In case encapsulation is needed before forwarding, move the reformat
object to the termination table as required.
Extend the hash table key to include tunnel information for the sake of
reusing reformat objects.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Don't use termination tables for packets that are steered to the slow path,
as a pre-step for supporting packet encap (packet reformat) action on
termination tables. Packet encap (reformat action) actions steer the packet
to the slow path until outer arp entries are resolved.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Check if QoS is enabled for the eswitch before attempting to configure
QoS parameters and emit a netlink error if not supported.
Introduce an API to check if QoS is supported for the eswitch.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If udevd is configured to rename interfaces according to persistent
naming rules and if a network interface has phys_port_name in sysfs,
its contents will be appended to the interface name.
However, register_netdev creates device in sysfs and if
devlink_port_register is called after that, there is a timeframe in
which udevd may read an empty phys_port_name value. The consequence is
that the interface will lose this suffix and its name will not be
really persistent.
The solution is to register the port before registering a netdev.
Fixes: c6acd629ee ("net/mlx5e: Add support for devlink-port in non-representors mode")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The original condition rejected all egress rules that
are not on tunnel device.
Also, the whole point of this egress reject was to disallow bad
rules because of egdev which doesn't exists today, so remove
this check entirely.
Fixes: 0a7fcb78cc ("net/mlx5e: Support inner header rewrite with goto action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Register loopback which is needed for tunnel restoration, is now always
enabled if supported and not just with metadata enabled, check for
that instead.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix the following warnings: [-Werror=frame-larger-than=]
In function ‘mlx5_tc_ct_entry_add_rule’:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:541:1:
error: the frame size of 1136 bytes is larger than 1024 bytes
In function ‘__mlx5_tc_ct_flow_offload’:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:1049:1:
error: the frame size of 1168 bytes is larger than 1024 bytes
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
If CONFIG_MLX5_TC_CT isn't enabled, all offloading of eswitch tc rules
fails on parsing ct match, even if there is no ct match.
Return success if there is no ct match, regardless of config.
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:
In function mlx5_tc_ct_parse_match:
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:699:36: warning:
variable unnew set but not used [-Wunused-but-set-variable]
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Restore modify header writes the chain mapping on the packet.
This modify header and action is added on all prios connections,
and gets overwritten with the same value consecutively in prios
of the same chain.
Use the chain's modify header only for the last prio of a given tc
chain.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, if firmware doesn't support fwd and modify, driver fails
initializing eswitch chains while entering switchdev mode.
Instead, on such cases, disable the chains and prio feature (as we can't
restore the chain on miss) and the usage of fwd and modify.
Fixes: 8f1e0b97cc ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When CONFIG_MLX5_ESWITCH is unset, clang warns:
In file included from drivers/net/ethernet/mellanox/mlx5/core/main.c:58:
drivers/net/ethernet/mellanox/mlx5/core/eswitch.h:670:1: warning: unused
function 'esw_add_restore_rule' [-Wunused-function]
esw_add_restore_rule(struct mlx5_eswitch *esw, u32 tag)
^
1 warning generated.
This stub function is missing inline; add it to suppress the warning.
Fixes: 11b717d615 ("net/mlx5: E-Switch, Get reg_c0 value on CQE")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Clang warns:
../drivers/net/ethernet/mellanox/mlx5/core/mr.c:63:21: warning: variable
'key' is uninitialized when used here [-Wuninitialized]
mkey_index, key, mkey->key);
^~~
../drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.h:54:6: note:
expanded from macro 'mlx5_core_dbg'
##__VA_ARGS__)
^~~~~~~~~~~
../include/linux/dev_printk.h:114:39: note: expanded from macro
'dev_dbg'
dynamic_dev_dbg(dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
../include/linux/dynamic_debug.h:158:19: note: expanded from macro
'dynamic_dev_dbg'
dev, fmt, ##__VA_ARGS__)
^~~~~~~~~~~
../include/linux/dynamic_debug.h:143:56: note: expanded from macro
'_dynamic_func_call'
__dynamic_func_call(__UNIQUE_ID(ddebug), fmt, func, ##__VA_ARGS__)
^~~~~~~~~~~
../include/linux/dynamic_debug.h:125:15: note: expanded from macro
'__dynamic_func_call'
func(&id, ##__VA_ARGS__); \
^~~~~~~~~~~
../drivers/net/ethernet/mellanox/mlx5/core/mr.c:47:8: note: initialize
the variable 'key' to silence this warning
u8 key;
^
= '\0'
1 warning generated.
key's initialization was removed in commit fc6a9f86f0 ("{IB,net}/mlx5:
Assign mkey variant in mlx5_ib only") but its use was not fully removed.
Remove it now so that there is no more warning.
Fixes: fc6a9f86f0 ("{IB,net}/mlx5: Assign mkey variant in mlx5_ib only")
Link: https://github.com/ClangBuiltLinux/linux/issues/932
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
XDP-redirect is broken in this driver sfc. XDP_REDIRECT requires
tailroom for skb_shared_info when creating an SKB based on the
redirected xdp_frame (both in cpumap and veth).
The fix requires some initial explaining. The driver uses RX page-split
when possible. It reserves the top 64 bytes in the RX-page for storing
dma_addr (struct efx_rx_page_state). It also have the XDP recommended
headroom of XDP_PACKET_HEADROOM (256 bytes). As it doesn't reserve any
tailroom, it can still fit two standard MTU (1500) frames into one page.
The sizeof struct skb_shared_info in 320 bytes. Thus drivers like ixgbe
and i40e, reduce their XDP headroom to 192 bytes, which allows them to
fit two frames with max 1536 bytes into a 4K page (192+1536+320=2048).
The fix is to reduce this drivers headroom to 128 bytes and add the 320
bytes tailroom. This account for reserved top 64 bytes in the page, and
still fit two frame in a page for normal MTUs.
We must never go below 128 bytes of headroom for XDP, as one cacheline
is for xdp_frame area and next cacheline is reserved for metadata area.
Fixes: eb9a36be7f ("sfc: perform XDP processing on received packets")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the case where the last mvneta_poll did not process all
RX packets, we need to xor the pp->cause_rx_tx or port->cause_rx_tx
before claculating the rx_queue.
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
printk in macro vxge_debug_ll uses __VA_ARGS__ without "##" prefix,
it causes a build error when there is no variable
arguments(e.g. only fmt is specified.).
Signed-off-by: Zheng Wei <wei.zheng@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove set but not used variables 'sw_comp_cons' and 'hw_comp_cons'
to fix gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function qede_selftest_receive_traffic:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:1569:20:
warning: variable sw_comp_cons set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function qede_selftest_receive_traffic:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:1569:6:
warning: variable hw_comp_cons set but not used [-Wunused-but-set-variable]
After removing 'hw_comp_cons',the memory barrier 'rmb()' and its comments become useless,
so remove them as well.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat all internal delay variants the same as RGMII.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4_dma_reset() function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The init_systime() function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: oss-drivers@netronome.com
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: oss-drivers@netronome.com
To: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Tariq Toukan <tariqt@mellanox.com>
To: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit set a value of 2^31-1 in order to "disable" the shaper
on a given a port. However, the length of the maximum shaper rate field
was not updated from 28 bits to 31 bits, which means ports are still
limited to ~268Gbps despite supporting speeds of 400Gbps.
Fix this by increasing the field's length.
Fixes: 92afbfedb7 ("mlxsw: reg: Increase MLXSW_REG_QEEC_MAS_DIS")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify code, which
contains platform_get_resource and devm_ioremap_resource.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being a non-physical port, the CPU port does not have an ocelot_port
structure, so the ocelot_port_writel call inside the
ocelot_port_set_maxlen() function would access data behind a NULL
pointer.
This is a patch for net-next only, the net tree boots fine, the bug was
introduced during the net -> net-next merge.
Fixes: 1d34357931 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Fixes: a8015ded89 ("net: mscc: ocelot: properly account for VLAN header length when setting MRU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,
commit c219399988 ("cxgb4: add support for high priority filters")
hardware TID index can start after the high priority region, which
has introduced a regression resulting in remove filters entry
failure for cxgb4 unload path. This patch fix that.
Fixes: c219399988 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected almost all
unsupported parameters (missing sample_rate_interval).
As a side effect of these changes the error code for
unsupported params changes from EINVAL to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
As a side effect of these changes the error code for
unsupported params changes from EINVAL to EOPNOTSUPP.
The driver was missing a check for rate_sample_interval.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver correctly rejects all unsupported
parameters, no functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver correctly rejects all unsupported
parameters, no functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RED ECN nodrop mode means that non-ECT traffic should not be early-dropped,
but enqueued normally instead. In Spectrum systems, this is achieved by
disabling CWTPM.ew (enable WRED) for a given traffic class.
So far CWTPM.ew was unconditionally enabled. Instead disable it when the
RED qdisc is in nodrop mode.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not every stmmac based platform makes use of the eth_wake_irq or eth_lpi
interrupts. Use the platform_get_irq_byname_optional variant for these
interrupts, so no error message is displayed, if they can't be found.
Rather print an information to hint something might be wrong to assist
debugging on platforms which use these interrupts.
Signed-off-by: Markus Fuchs <mklntf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corresponds to the MAC_SPOOFING_TX privilege in the hardware.
Some firmware versions on some cards don't support the feature, so check
the TX_MAC_SECURITY capability and fail EOPNOTSUPP if trying to enable
spoofchk on a NIC that doesn't support it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a statement that is indented incorrectly, remove a space.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more T5/T6 registers to be collected in register dump:
1. MPS register range 0x9810 to 0x9864 and 0xd000 to 0xd004.
2. NCSI register range 0x1a114 to 0x1a130 and 0x1a138 to 0x1a1c4.
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove dummy functions declaration, the dummy functions are not needed
since fs_dr is the only one to call mlx5dr and both fs_dr and dr files
depend on the same config flag (MLX5_SW_STEERING).
Fixes: 70605ea545 ("net/mlx5: DR, Expose APIs for direct rule managing")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This action allows to go to a flow table based on the table id.
Goto flow table id is required for supporting user space SW.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
All callers needs to work on mlx5_core_dev and it is already derived
before calling mlx5_devlink_eswitch_check().
Hence, accept mlx5_core_dev in mlx5_devlink_eswitch_check().
Given that it works on mlx5_core_dev change helper function name to
drop devlink prefix.
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Annotate mutex destroy to keep it symmetric to init sequence.
It should be destroyed after its users (representor netdevices) are
destroyed in below flow.
esw_offloads_disable()
esw_offloads_unload_rep()
Hence, initialize the mutex before creating the representors which uses
it.
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow passing NULL spec when creating a flow rule. Such rules will act
as "catch all" flow rules.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Following introduction of per vport configuration of vport and rep,
unload all reps per rep type is still needed as IB reps can be
unloaded individually. However, a few internal functions exist purely
for this purpose, merge them to a single function.
This patch doesn't change any existing functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, ECPF eswitch manager does one-time only configuration for
VF vports when device switches to offloads mode. However, when num of
VFs changed from host side, driver doesn't update VF vports
configurations.
Hence, perform VFs vport configuration update whenever num_vfs change
event occurs.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Both legacy and offload modes require vport setup, only offload mode
requires rep setup. Before this patch, vport and rep operations are
separated applied to all relevant vports in different stages.
Change to use per vport configuration, so that vport and rep operations
are modularized per vport.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vport enable and disable sequence is incorrect. It should be:
enable()
esw_vport_setup_acl,
esw_vport_setup,
esw_vport_enable_qos.
disable()
esw_vport_disable_qos,
esw_vport_cleanup,
esw_vport_cleanup_acl.
Instead of having two setup functions for port and acl, merge
acl setup to port setup function.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename esw_apply_vport_config() to esw_vport_setup(), and add new
helper function esw_vport_cleanup() to make them symmetric.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
esw_vport_enable_qos can return error in cases below:
1. QoS is already enabled. Warnning is useless in this case.
2. Create scheduling element cmd failed. There is already a warning.
Remove the redundant warnning if esw_vport_enable_qos returns err.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Consider scenario below, CPU 1 is at risk to query already destroyed
drop counters. Need to apply the same state mutex when disabling vport.
+-------------------------------+-------------------------------------+
| CPU 0 | CPU 1 |
+-------------------------------+-------------------------------------+
| mlx5_device_disable_sriov | mlx5e_get_vf_stats |
| mlx5_eswitch_disable | mlx5_eswitch_get_vport_stats |
| esw_disable_vport | mlx5_eswitch_query_vport_drop_stats |
| mlx5_fc_destroy(drop_counter) | mlx5_fc_query(drop_counter) |
+-------------------------------+-------------------------------------+
Fixes: b8a0dbe3a9 ("net/mlx5e: E-switch, Add steering drop counters")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
esw_vport_create_legacy_acl_tables bails out immediately for eswitch
manager, hence remove all the check of esw manager cap after.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Leon Romanovsky says:
====================
This series fixes various corner cases in the mlx5_ib MR cache
implementation, see specific commit messages for more information.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Due to dependencies
* branch 'mlx5_mr-cache':
RDMA/mlx5: Allow MRs to be created in the cache synchronously
RDMA/mlx5: Revise how the hysteresis scheme works for cache filling
RDMA/mlx5: Fix locking in MR cache work queue
RDMA/mlx5: Lock access to ent->available_mrs/limit when doing queue_work
RDMA/mlx5: Fix MR cache size and limit debugfs
RDMA/mlx5: Always remove MRs from the cache before destroying them
RDMA/mlx5: Simplify how the MR cache bucket is located
RDMA/mlx5: Rename the tracking variables for the MR cache
RDMA/mlx5: Replace spinlock protected write with atomic var
{IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
{IB,net}/mlx5: Assign mkey variant in mlx5_ib only
{IB,net}/mlx5: Setup mkey variant before mr create command invocation
As mlx5_ib is the only user of the mlx5_core_create_mkey_cb, move the
logic inside mlx5_ib and cleanup the code in mlx5_core.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
mkey variant is not required for mlx5_core use, move the mkey variant
counter to mlx5_ib.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
On reg_mr_callback() mlx5_ib is recalculating the mkey variant which is
wrong and will lead to using a different key variant than the one
submitted to firmware on create mkey command invocation.
To fix this, we store the mkey variant before invoking the firmware
command and use it later on completion (reg_mr_callback).
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
We need to unlock before returning if this allocation fails.
Fixes: 75f3627099 ("octeontx2-pf: Support to enable/disable pause frames via ethtool")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bounds check on index is off by one and can lead to
an out of bounds access on array priv->filters_loc when index is
RXCHK_BRCM_TAG_MAX.
Fixes: bb9051a2b2 ("net: systemport: Add support for WAKE_FILTER")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear action, as with software, removes all ct metadata from
the packet.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark packets with a unique tupleid, and on miss use that id to get
the act ct restore_cookie. Using that restore cookie, we ask CT to
restore the relevant info on the SKB.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register driver callbacks with the nf flow table platform.
FT add/delete events will create/delete FTE in the CT/CT_NAT tables.
Restoring the CT state on miss will be added in the following patch.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading tc ct action and ct matches.
We translate the tc filter with CT action the following HW model:
+-------------------+ +--------------------+ +--------------+
+ pre_ct (tc chain) +----->+ CT (nat or no nat) +--->+ post_ct +----->
+ original match + | + tuple + zone match + | + fte_id match + |
+-------------------+ | +--------------------+ | +--------------+ |
v v v
set chain miss mapping set mark original
set fte_id set label filter
set zone set established actions
set tunnel_id do nat (if needed)
do decap
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we write chain register mapping on miss from the the last
prio of a chain. It is used to restore the chain in software.
To support re-using the chain register mapping from global tables (such
as CT tuple table) misses, export the chain mapping.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FTEs in global tables may match on packets from multiple in_ports.
Provide the capability to omit the in_port match condition.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, flow tables are automatically connected according to their
<chain,prio,level> tuple.
Introduce global tables which are flow tables that are detached from the
eswitch chains processing, and will be connected by explicitly referencing
them from multiple chains.
Add this new table type, and allow connecting them by refenece.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eswitch offloads table, which has the reps (vport) rx miss rules,
was moved from OFFLOADS namespace [0,0] (prio, level), to [1,0], so
the restore table (the new [0,0]) can come before it. The destinations
of these miss rules is the rep root ft (ttc for non uplink reps).
Uplink rep root ft is created as OFFLOADS namespace [0,1], and is used
as a hook to next RX prio (either ethtool or ttc), but this fails to
pass fs_core level's check.
Move uplink rep root ft to OFFLOADS prio 1, level 1 ([1,1]), so it
will keep the same relative position after the restore table
change.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable reg c1 loopback if firmware reports it's supported,
as this is needed for restoring packet metadata (e.g chain).
Also define helper to query if it is enabled.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, PF missed to clear the port base VLAN for VF when
unload. In this case, the VLAN id will remain in the VLAN
table. This patch fixes it.
Fixes: 92f11ea177 ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the user manual, the ingress and egress VLAN filter
are configured at the same time. Currently, hclge_init_vlan_config()
and hclge_set_vlan_spoofchk() will both change the VLAN filter
switch. So it's necessary to read the old configuration before
modifying it.
Fixes: 22044f95fa ("net: hns3: add support for spoof check setting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if VF is loaded on the host side, the host doesn't
clear the VF's VLAN table entries when VF removing. In this
case, when doing reset and disabling sriov at the same time the
VLAN device over VF will be removed, but the VLAN table entries
in hardware are remained.
This patch fixes it by asking PF to clear the VLAN table entries for
VF when VF is removing. It also clears the VLAN table full bit
after VF VLAN table entries being cleared.
Fixes: c6075b1934 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS3 driver supports to configure TC numbers and TC to priority
map via "tc" tool. But when delete the rule, will fail, because
the HNS3 driver needs at least one TC, but the "tc" tool sets TC
number to zero when delete.
This patch makes sure that the TC number is at least one.
Fixes: 30d240dfa2 ("net: hns3: Add mqprio hardware offload support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters
(other than adaptive rx, which will now be rejected by core).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converting fallthrough comments to fallthrough; creates warnings
in this code when compiled with gcc.
This code is overly complicated and reads rather better with a
little refactoring and no fallthrough uses at all.
Remove the fallthrough comments and simplify the written source
code while reducing the object code size.
Consolidate duplicated switch/case blocks for IPV4 and IPV6.
defconfig x86-64 with sfc:
$ size drivers/net/ethernet/sfc/ethtool.o*
text data bss dec hex filename
10055 12 0 10067 2753 drivers/net/ethernet/sfc/ethtool.o.new
10135 12 0 10147 27a3 drivers/net/ethernet/sfc/ethtool.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/ibm/emac/core.c: In function __emac_mdio_write:
drivers/net/ethernet/ibm/emac/core.c:875:9: warning:
variable err set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
