This issue is specific to SLI-3 adapters, specifically when DIF is used.
Once seen, this message floods the logs:
9064 BLKGRD: lpfc_scsi_prep_dma_buf_s3: Too many sg segments from
dma_map_sg
The driver, upon detecting an error such as too many elements in an sglist,
misrepresents the error by treating it as a temporary resource issue by
returning MLQUEUE_HOST_BUSY. In these cases, no retry will fix it and it
should have been a hard error. The repeated retry was causing the spamming
of the log.
As for the initial reason of why an I/O encountered this issue at all is
not clear as parameters set by the driver should have avoided this. The
dm multipath maintainer has been notified of the issue.
Fix by changing the return code for the dma mapping routines to indicate
cases that are not retryable and return DID_ERROR on those cases.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter encounters a condition which causes the adapter to fail
(driver must detect the failure) simultaneously to a request to the driver
to reset the adapter (such as a host_reset), the reset path will be racing
with the asynchronously-detect adapter failure path. In the failing
situation, one path has started to tear down the adapter data structures
(io_wq's) while the other path has initiated a repeat of the teardown and
is in the lpfc_sli_flush_xxx_rings path and attempting to access the
just-freed data structures.
Fix by the following:
- In cases where an adapter failure is detected, rather than explicitly
calling offline_eratt() to start the teardown, change the adapter state
and let the later calls of posted work to the slowpath thread invoke the
adapter recovery. In essence, this means all requests to reset are
serialized on the slowpath thread.
- Clean up the routine that restarts the adapter. If there is a failure
from brdreset, don't immediately error and leave things in a partial
state. Instead, ensure the adapter state is set and finish the teardown
of structures before returning.
- If in the scsi host reset handler and the board fails to reset and
restart (which can be due to parallel reset/recovery paths), instead of
hard failing and explicitly calling offline_eratt() (which gets into the
redundant path), just fail out and let the asynchronous path resolve the
adapter state.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During cable pull testing a deadlock was seen between lpfc_nlp_counters()
vs lpfc_mbox_process_link_up() vs lpfc_work_list_done(). They are all
waiting on the shost->host_lock.
Issue is all of these cases raise irq when taking out the lock but use
spin_unlock_irq() when unlocking. The unlock path is will unconditionally
re-enable interrupts in cases where irq state should be preserved. The
re-enablement allowed the other paths to execute which then causes the
deadlock.
Fix by converting the lock/unlock to irqsave/irqrestore.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a test with high nvme remote port counts connected via a multi-hop FC
switch config where switches were systematically reset (e.g. fabric
partitioning and re-establishment), the nvme remote ports would switch
addresses based on the switch reconfiguration events. The driver would get
into a situation where the nvme port changed address, PLOGI and PRLI would
succeed nvme transport registration occurred, but subsequent LS requests by
the nvme subsystem failed due to a bad ndlp state and connectivity to the
device failed.
The driver hit a race condition on multiple devices that address swapped
simultaneously. In cases where the driver notices the remote port structure
came back as the same value as previously (meaning a nvme_rport structure
was re-enabled and did not go through devloss_tmo/connect_tmo_failures on
all controllers) the driver would unconditionally exit assuming the ndlp
information was correct. But, if the ndlp's had been swapped, the ndlp had
stale port state information, which when used by the LS request commands,
would fail the commands.
Fix by checking whether a node swap had occurred, and only exit if no ndlp
swap had occurred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In situations where zoning is not being used, thus NVMe initiators see
other NVMe initiators as well as NVMe targets, a link bounce on an
initiator will cause the NVMe initiators to spew "6169" State Error
messages.
The driver is not qualifying whether the remote port is a NVMe targer or
not before calling the lpfc_nvme_rescan_port(), which validates the role
and prints the message if its only an NVMe initiator.
Fix by the following:
- Before calling lpfc_nvme_rescan_port() ensure that the node is a NVMe
storage target or a NVMe discovery controller.
- Clean up implementation of lpfc_nvme_rescan_port. remoteport pointer
will always be NULL if a NVMe initiator only. But, grabbing of
remoteport pointer should be done under lock to coincide with the
registering of the remote port with the fc transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On an SLI-3 adapter which does not support NVMe, but with the driver global
attribute to enable nvme on any adapter if it does support NVMe
(e.g. module parameter lpfc_enable_fc4_type=3), the SGL and total SGE
values are being munged by the protocol enablement when it shouldn't be.
Correct by changing the location of where the NVME sgl information is being
applied, which will avoid any SLI-3-based adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If admin changes the devloss_tmo on an rport via the fc_remote_port rport
dev_loss_tmo attribute, the value is on set on scsi stack. The change is
not propagated to NVMe.
The set routine in the lldd lacks the call to
nvme_fc_set_remoteport_devloss() to set the value.
Fix by adding the call to the lldd set routine.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In tests with remote ports contantly logging out/logging coupled with
occassional local link bounce, if a remote port is disocnnected for longer
than devloss_tmo and then subsequently reconnected, eventually the test
will fail to login with the remote port and remote port connectivity is
lost.
When devloss_tmo expires, the driver does not free the node struct until
the port or npiv instances is being deleted. The node is left allocated but
the state set to UNUSED. If the node was in the process of logging in when
the local link drop occurred, meaning the RPI was allocated for the node in
order to send the ELS, but not yet registered which comes after successful
login, the node is moved to the NPR state, and if devloss expires, to
UNUSED state. If the remote port comes back, the node associated with it
is restarted and this path happens to allocate a new RPI and overwrites the
prior RPI value. In the cases where the port was logged in and loggs out,
the path did release the RPI but did not set the node rpi value. In the
cases where the remote port never finished logging in, the path never did
the call to release the rpi. In this latter case, when the node is
subsequently restore, the new rpi allocation overwrites the rpi that was
not released, and the rpi is now leaked. Eventually the port will run out
of RPI resources to log into new remote ports.
Fix by following changes:
- When an rpi is released, do so under locks and ensure the node rpi value
is set to a non-allocated value (LPFC_RPI_ALLOC_ERROR). Note:
refactored to a small service routine to avoid indentation issues.
- When re-enabling a node, check the rpi value to determine if a new
allocation is necessary. If already set, use the prior rpi.
Enhanced logging to help in the future.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a remote port is removed and remains removed for devloss_tmo, if an RSCN
is subsequently received indicating the presence of the remte port, the
driver does not login to and rediscovery the remote port.
Currently, in order to for a port to be rediscovered post an RSCN, the node
state must be NPR to reflect not logged in. When devloss expires, the node
state is marked UNUSED. When an RSCN occurs, the nodes referenced by the
RSCN will have a NPR_2B_DISC flag set, but the re-login will only be
attempted if the node is in NPR_NODE state. Thus the node is skipped over.
Fix by recognizing the NPR_2B_DISC and UNUSED and transition the node back
to NPR state to allow the re-login to take place.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If an admin updates lpfc's devloss_tmo sysfs attribute, the kernel will
oops.
Coding of a loop allowed a new value (rport) to be set/checked for null
followed by an older value (remoteport) checked for null to allow progress
where the new value, even though null, will be referenced.
Rework the logic to validate and prevent any reference to the null ptr.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It's possible for the driver to initiate an FLOGI and before it completes,
another link down/up transition occurs requiring a new FLOGI. Currently,
nothing is done to abort/noop the older FLOGI request to the adapter, so if
this transition occurs and the FLOGI completion is received after the link
down/up transition, the driver may erroneously act on the older FLOGI. In
most cases, the adapter properly terminates/fails the FLOGI, but there is a
timing condition where the FLOGI may complete on the wire prior to the
transition, but the response may not be seen/processed by the driver before
the driver sees the link transition.
Fix by having the link down handler in the driver run through any
outstanding ELS's and change the completion handler of the ELS so that it
will be no-op'd and released.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When tearing down the adapter for a reset, online/offline, or driver
unload, the queue free routine would hit a GPF oops. This only occurs on
conditions where the number of hardware queues created is fewer than the
number of cpus in the system. In this condition cpus share a hardware
queue. And of course, it's the 2nd cpu that shares a hardware that
attempted to free it a second time and hit the oops.
Fix by reworking the cpu to hardware queue mapping such that:
Assignment of hardware queues to cpus occur in two passes:
first pass: is first time assignment of a hardware queue to a cpu.
This will set the LPFC_CPU_FIRST_IRQ flag for the cpu.
second pass: for cpus that did not get a hardware queue they will
be assigned one from a primary cpu (one set in first pass).
Deletion of hardware queues is driven by cpu itteration, and queues
will only be deleted if the LPFC_CPU_FIRST_IRQ flag is set.
Also contains a few small cleanup fixes and a little better logging.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The adapter reset path (lpfc_sli_hba_down) is taking/releasing a lock with
irq. But, the path is already under the hbalock which raised irq so it's
unnecessary.
Convert to simple lock/unlock.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
lpfc_nvme_register_port hit a null prev_ndlp pointer in a test with lots of
target ports swapping addresses. The oldport value was stale, thus it's
ndlp (prev_ndlp set to it) was used.
Fix by moving oldrport pointer checks, and if used prev_ndlp pointer
assignment, to be done while the lock is held.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is inadvertently trying to issue an INIT_VPI mailbox command on
an SLI-3 driver. The command is specific to SLI-4. When the call is made to
send the command, if on an SLI-3 adapter, an array pointer is NULL and the
driver will oops.
Fix by restricting the command to SLI-4 adapters only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target issues an ADISC to the port and the target is a NVME target,
the driver is inadvertantly invalidating the login and marking the remote
port as logged out. Communication with the target is lost.
Revise the ADISC check so that FCP or NVME targets will be marked valid at
the end of ADISC processing. Enhance logging to recognize condition
better.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some remote ports may be slow in registering their GID_FT protocol
information with the fabric. If the remote port is an initiator, it may
send PLOGI to the port before the GID_FT logic is complete. Meaning, after
accepting the PLOGI, when the driver may see no response to the GID_FT that
is issued after the login to determine the protocols supported so that
proper PRLI's may be transmit. If the driver has no fc4 information, it
currently stops and the remote port is not discovered.
Fix by issuing a LOGO when there is no GID_FT information. The LOGO
completion handling will attempt to re-login if the nport_id is still
present.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In cases of remote-port-side cable pull/replug, there happens to be a
target that upon replug will send the port a PLOGI, a PRLI, and a LOGO.
When this sequence is received by the driver, the PLOGI accepted and a
GFT_ID is issued to find the protocol support for the remote port. While
the GFT_ID is outstanding, a LOGO is received. The driver logs the remote
port out and unregisters the RPI and schedules a new PLOGI transmission.
However, the GFT_ID was not terminated. When it completed, the driver
attempted to transition the remote port to PRLI transmission, which cancels
the PLOGI scheduling. The PRLI transmit attempt is rejected by the adapter
as the remote port is not logged in. No retry is attempted as it's expected
the logout is noted and the supposedly scheduled PLOGI should address the
state. As there is no PLOGI, the remote port does not get re-discovered.
Fix by aborting the outstanding GFT_ID if the related remote port is logged
out.
Ensure a PRLI transmit attempt only occurs if the remote port is logging
in. This avoids the incorrect attempt while logged out.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the adapter is reset while there are outstanding ELS's, subsequent
reinitialization of the adapter will fail as it has not recovered all of
the io contexts relative to the ELS's.
If an ELS timed out or otherwise failed and an the ELS was attempted to be
aborted (which changes the ELS completion context), in causes where the
driver generates completions for the outstanding IO as the adapter would
not due to being reset, the driver released only the ELS context and failed
to release the abort context. When the adapter went to reinit, as it had
not received all of the contexts, it failed to reinit.
Fix by having the ELS completion handler identify the driver-generated
completion status and release the abort context.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unusually high IO latency can be observed with little IO in progress. The
latency may remain high regardless of amount of IO and can only be cleared
by forcing lpfc_fcp_imax values to non-zero and then back to zero.
The driver's eq_delay mechanism that scales the interrupt coalescing based
on io completion load failed to reduce or turn off coalescing when load
decreased. Specifically, if no io completed on a cpu within an eq_delay
polling window, the eq delay processing was skipped and no change was made
to the coalescing values. This left the coalescing values set when they
were no longer applicable.
Fix by always clearing the percpu counters for each time period and always
run the eq_delay calculations if an eq has a non-zero coalescing value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a timer routine uses workqueues, it could fire before the workqueue is
allocated.
Fix by allocating the workqueue before the timer routines are setup
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After seeing some interoperability issues with ADISC, it was determined the
ELS definitions in lpfc were using types that allowed the compiler to add
pad to the structure, causing the structure to no longer be per spec. The
offending structures are ADISC, FAN, and RNID.
This patch implements the simple fix of eliminating the pad by forcing the
compiler to pack the structure. Care was taken to ensure field accesses
won't be by operations that would hit a bad field alignment.
The better solution would be to convert to the uapi fc header definitions,
but the number of changes required to do is rather intrusive so this course
of action was deferred.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When connected to a high number of remote ports, the driver is encountering
PLOGI errors. The errors are due to adapter detected failures indicating
illegal field values.
Turns out the driver was prematurely clearing an RPI bitmask before waiting
for an UNREG_RPI mailbox completion. This allowed the RPI to be reused
before it was actually available.
Fix by clearing RPI bitmask only after UNREG_RPI mailbox completion.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi-mq operation inherently performs pre-allocation of resources for
blk-mq request queues. Even though the kdump environment reduces the
configuration to a single CPU, thus 1 hardware queue, which helps
significantly, the resources are still rather large due to the per request
allocations. blk-mq pre-allocations can be over 4KB per request. With
adapter can_queue values in the 4k or 8k range, this can easily be 32MBs
before any other driver memory is factored in. Driver SGL DMA buffer
allocation can be up to 8KB per request as well adding an additional
64MB. Totals are well over 100MB for a single shost. Given kdump memory
auto-sizing utilities don't accommodate this amount of memory well, it's
very possible for kdump to fail due to lack of memory.
Fix by having the driver recognize that it is booting within a kdump
context and reduce the number of requests it will support to a more
reasonable value.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As dma_pool_destroy and mempool_destroy functions has NULL check. We may
not need NULL check before calling them.
Fix below warnings reported by coccicheck
./drivers/scsi/lpfc/lpfc_mem.c:252:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:255:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:258:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:261:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:265:2-18: WARNING: NULL check before some
freeing functions is not needed.
./drivers/scsi/lpfc/lpfc_mem.c:269:2-17: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Static structure ufs_hba_qcom_vops, of type ufs_hba_variant_ops, is used
only once, when it is passed as the second argument to function
ufshcd_pltfrm_init(). In the definition of ufshcd_pltfrm_init(), its second
parameter (corresponding to ufs_hba_qcom_vops) is declared as
constant. Hence declare ufs_hba_qcom_vops itself constant as well to
protect it from unintended modification. Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As spin_unlock_irq will enable interrupts.
Function lpfc_findnode_rpi is called from
lpfc_sli_abts_err_handler (./drivers/scsi/lpfc/lpfc_sli.c)
<- lpfc_sli_async_event_handler
<- lpfc_sli_process_unsol_iocb
<- lpfc_sli_handle_fast_ring_event
<- lpfc_sli_fp_intr_handler
<- lpfc_sli_intr_handler
and lpfc_sli_intr_handler is an interrupt handler.
Interrupts are enabled in interrupt handler. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq in
IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the redundant initialization code.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable ret is initialized to a value that is never read and it is
re-assigned later and immediately returns. Clean up the code by removing
rc and just returning 0.
[mkp: typo]
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid code duplication between qla2x00_alloc_offload_mem() and
qla2x00_alloc_fw_dump() by moving the FCE and EFT buffer allocation and
initialization to separate functions. Cleanly track failure and success by
making sure that the ha->eft, ha->fce and respective eft_dma, fce_dma
members are set if and only if the buffers are properly allocated and
initialized. Avoid pointless buffer reallocation. Eliminate some goto
statements. Make sure the fce_enabled flag is cleared when the FCE buffer
is freed.
Fixes: ad0a0b01f0 ("scsi: qla2xxx: Fix Firmware dump size for Extended login and Exchange Offload")
Fixes: a28d9e4ef9 ("scsi: qla2xxx: Add support for multiple fwdump templates/segments")
Cc: Joe Carnuccio <joe.carnuccio@cavium.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In qla2x00_alloc_fw_dump(), an existing EFT buffer (e.g. from previous
invocation of qla2x00_alloc_offload_mem()) is freed. The buffer is then
re-allocated, but without setting the eft and eft_dma fields to the new
values.
Fixes: a28d9e4ef9 ("scsi: qla2xxx: Add support for multiple fwdump templates/segments")
Cc: Joe Carnuccio <joe.carnuccio@cavium.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <hmadhani@marvell.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 8c0d3a02c1 ("PCI: Add accessors for PCI Express Capability") added
accessors for the PCI Express Capability so that drivers didn't need to be
aware of differences between v1 and v2 of the PCI Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 8c0d3a02c1 ("PCI: Add accessors for PCI Express Capability") added
accessors for the PCI Express Capability so that drivers didn't need to be
aware of differences between v1 and v2 of the PCI Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable retv is initialized to a value that is never read and it is
re-assigned later. The initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This should be 'pmcraid', not 'pcmraid'
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mark switch cases where we are expecting to fall through.
Fix the following warnings (Building: rpc_defconfig arm):
drivers/scsi/arm/fas216.c: In function fas216_disconnect_intr :
drivers/scsi/arm/fas216.c:913:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (fas216_get_last_msg(info, info->scsi.msgin_fifo) == ABORT) {
^
drivers/scsi/arm/fas216.c:919:2: note: here
default: /* huh? */
^~~~~~~
drivers/scsi/arm/fas216.c: In function fas216_kick :
drivers/scsi/arm/fas216.c:1959:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_allocate_tag(info, SCpnt);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1960:2: note: here
case TYPE_OTHER:
^~~~
drivers/scsi/arm/fas216.c: In function fas216_busservice_intr :
drivers/scsi/arm/fas216.c:1413:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_stoptransfer(info);
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1414:2: note: here
case STATE(STAT_STATUS, PHASE_SELSTEPS):/* Sel w/ steps -> Status */
^~~~
drivers/scsi/arm/fas216.c:1424:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
fas216_stoptransfer(info);
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:1425:2: note: here
case STATE(STAT_MESGIN, PHASE_COMMAND): /* Command -> Message In */
^~~~
drivers/scsi/arm/fas216.c: In function fas216_funcdone_intr :
drivers/scsi/arm/fas216.c:1573:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if ((stat & STAT_BUSMASK) == STAT_MESGIN) {
^
drivers/scsi/arm/fas216.c:1579:2: note: here
default:
^~~~~~~
drivers/scsi/arm/fas216.c: In function fas216_handlesync :
drivers/scsi/arm/fas216.c:605:20: warning: this statement may fall through [-Wimplicit-fallthrough=]
info->scsi.phase = PHASE_MSGOUT_EXPECT;
~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~
drivers/scsi/arm/fas216.c:607:2: note: here
case async:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a module parameter and sysfs interface to select
whether the queue depth for each device should be based on the value
suggested by firmware (the default) or the maximum supported by the
controller (can_queue).
Although we have a sysfs interface per sdev to change the queue depth of
individual scsi devices, this implementation provides a single sysfs entry
per shost to switch between the controller max and the value reported by
firmware. The module parameter can provide an interface for one time grub
settings and provides persistent settings across the boot.
[mkp: tweaked commit desc]
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make the code easier to read by converting 'goto' statements into
'return' statements.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following Coverity complaint:
Null-checking sp->u.iocb_cmd.u.ctarg.rsp suggests that it may be null, but
it has already been dereferenced on all paths leading to the check.
See also commit e374f9f592 ("scsi: qla2xxx: Migrate switch registration commands away from mailbox interface") # v4.16.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of calling qla2x00_fcport_event_handler() and letting the switch
statement inside that function decide which other function to call, call
the latter function directly. Remove the event member from the event_arg
structure because it is no longer needed. Remove the
qla_handle_els_plogi_done() function because it is never called.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is easy to mix up the QLA_* and the MBS_* status codes. Complain loudly
if that happens.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The C language supports implicit casting of void pointers to non-void
pointers. Remove explicit sts_entry_* casts that are not necessary.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split srb_cmd.ctx into two pointers such that the compiler can check the
type of that pointer.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Not calling sp->done() from the command completion path is a severe bug.
Hence complain loudly if that happens.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The LIO core requires that the target driver callback functions
.queue_data_in() and .queue_status() call target_put_sess_cmd() or
transport_generic_free_cmd(). These calls may happen synchronously or
asynchronously. Make sure that one of these LIO functions is called in case
a command has been aborted. This patch avoids that the code for removing a
session hangs due to commands that do not make progress.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: 694833ee00 ("scsi: tcm_qla2xxx: Do not allow aborted cmd to advance.") # v4.13.
Fixes: a07100e00a ("qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM") # v4.5.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since struct sg_table is used in nvme-fc-driver.h, include
<linux/scatterlist.h> from that header file.
Since no definitions or declarations from <linux/blk-mq.h> are used in the
qla_nvme.h header file, do not include <linux/blk-mq.h> from that header
file.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that this function crashes if mcmd == NULL.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
