The PCA9552 lines can be used either for driving LEDs or as GPIOs. The
manual states that for LEDs, the operation is open-drain:
The LSn LED select registers determine the source of the LED data.
00 = output is set LOW (LED on)
01 = output is set high-impedance (LED off; default)
10 = output blinks at PWM0 rate
11 = output blinks at PWM1 rate
For GPIOs it suggests a pull-up so that the open-case drives the line
high:
For use as output, connect external pull-up resistor to the pin
and size it according to the DC recommended operating
characteristics. LED output pin is HIGH when the output is
programmed as high-impedance, and LOW when the output is
programmed LOW through the ‘LED selector’ register. The output
can be pulse-width controlled when PWM0 or PWM1 are used.
Now, I have a hardware design that uses the LED controller to control
LEDs. However, for $reasons, we're using the leds-gpio driver to drive
the them. The reasons are here are a tangent but lead to the discovery
of the inversion, which manifested as the LEDs being set to full
brightness at boot when we expected them to be off.
As we're driving the LEDs through leds-gpio, this means wending our way
through the gpiochip abstractions. So with that in mind we need to
describe an active-low GPIO configuration to drive the LEDs as though
they were GPIOs.
The set() gpiochip callback in leds-pca955x does the following:
...
if (val)
pca955x_led_set(&led->led_cdev, LED_FULL);
else
pca955x_led_set(&led->led_cdev, LED_OFF);
...
Where LED_FULL = 255. pca955x_led_set() in turn does:
...
switch (value) {
case LED_FULL:
ls = pca955x_ledsel(ls, ls_led, PCA955X_LS_LED_ON);
break;
...
Where PCA955X_LS_LED_ON is defined as:
#define PCA955X_LS_LED_ON 0x0 /* Output LOW */
So here we have some type confusion: We've crossed domains from GPIO
behaviour to LED behaviour without accounting for possible inversions
in the process.
Stepping back to leds-gpio for a moment, during probe() we call
create_gpio_led(), which eventually executes:
if (template->default_state == LEDS_GPIO_DEFSTATE_KEEP) {
state = gpiod_get_value_cansleep(led_dat->gpiod);
if (state < 0)
return state;
} else {
state = (template->default_state == LEDS_GPIO_DEFSTATE_ON);
}
...
ret = gpiod_direction_output(led_dat->gpiod, state);
In the devicetree the GPIO is annotated as active-low, and
gpiod_get_value_cansleep() handles this for us:
int gpiod_get_value_cansleep(const struct gpio_desc *desc)
{
int value;
might_sleep_if(extra_checks);
VALIDATE_DESC(desc);
value = _gpiod_get_raw_value(desc);
if (value < 0)
return value;
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
return value;
}
_gpiod_get_raw_value() in turn calls through the get() callback for the
gpiochip implementation, so returning to our get() implementation in
leds-pca955x we find we extract the raw value from hardware:
static int pca955x_gpio_get_value(struct gpio_chip *gc, unsigned int offset)
{
struct pca955x *pca955x = gpiochip_get_data(gc);
struct pca955x_led *led = &pca955x->leds[offset];
u8 reg = pca955x_read_input(pca955x->client, led->led_num / 8);
return !!(reg & (1 << (led->led_num % 8)));
}
This behaviour is not symmetric with that of set(), where the val is
inverted by the driver.
Closing the loop on the GPIO_ACTIVE_LOW inversions,
gpiod_direction_output(), like gpiod_get_value_cansleep(), handles it
for us:
int gpiod_direction_output(struct gpio_desc *desc, int value)
{
VALIDATE_DESC(desc);
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
else
value = !!value;
return _gpiod_direction_output_raw(desc, value);
}
All-in-all, with a value of 'keep' for default-state property in a
leds-gpio child node, the current state of the hardware will in-fact be
inverted; precisely the opposite of what was intended.
Rework leds-pca955x so that we avoid the incorrect inversion and clarify
the semantics with respect to GPIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Matt Spinler <mspinler@linux.vnet.ibm.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The "activity" trigger was inspired by the heartbeat one, but aims at
providing instant indication of the immediate CPU usage. Under idle
condition, it flashes 10ms every second. At 100% usage, it flashes
90ms every 100ms. The blinking frequency increases from 1 to 10 Hz
until either the load is high enough to saturate one CPU core or 50%
load is reached on a single-core system. Then past this point only the
duty cycle increases from 10 to 90%.
This results in a very visible activity reporting allowing one to
immediately tell whether a machine is under load or not, making it
quite suitable to be used in clusters.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The indicator LED was registered in probe but was not removed in driver
remove callback. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Use integer numbers for LEDs, 0 is the flash and 1 is the indicator.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
DT bindings document the property "ams,input-max-microamp" that limits the
chip's maximum input current. The driver and the DTS however used
"peak-current-limit" property. Fix this by using the property documented
in DT binding documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=E1ff
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED class drivers improvements:
leds-pca955x:
- add Device Tree support and bindings
- use devm_led_classdev_register()
- add GPIO support
- prevent crippled LED class device name
- check for I2C errors
leds-gpio:
- add optional retain-state-shutdown DT property
- allow LED to retain state at shutdown
leds-tlc591xx:
- merge conditional tests
- add missing of_node_put
leds-powernv:
- delete an error message for a failed memory allocation in
powernv_led_create()
leds-is31fl32xx.c
- convert to using custom %pOF printf format specifier
Constify attribute_group structures in:
- leds-blinkm
- leds-lm3533
Make several arrays static const in:
- leds-aat1290
- leds-lp5521
- leds-lp5562
- leds-lp8501"
* tag 'leds_for_4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca955x: check for I2C errors
leds: gpio: Allow LED to retain state at shutdown
dt-bindings: leds: gpio: Add optional retain-state-shutdown property
leds: powernv: Delete an error message for a failed memory allocation in powernv_led_create()
leds: lp8501: make several arrays static const
leds: lp5562: make several arrays static const
leds: lp5521: make several arrays static const
leds: aat1290: make array max_mm_current_percent static const
leds: pca955x: Prevent crippled LED device name
leds: lm3533: constify attribute_group structure
dt-bindings: leds: add pca955x
leds: pca955x: add GPIO support
leds: pca955x: use devm_led_classdev_register
leds: pca955x: add device tree support
leds: Convert to using %pOF instead of full_name
leds: blinkm: constify attribute_group structures.
leds: tlc591xx: add missing of_node_put
leds: tlc591xx: merge conditional tests
We get a link error when V4L2_FLASH_LED_CLASS=m and AS3645A is built-in:
drivers/leds/leds-as3645a.o: In function `as3645a_v4l2_setup':
leds-as3645a.c:(.text+0x258): undefined reference to `v4l2_flash_init'
leds-as3645a.c:(.text+0x284): undefined reference to `v4l2_flash_indicator_init'
leds-as3645a.c:(.text+0x2a4): undefined reference to `v4l2_flash_release'
drivers/leds/leds-as3645a.o: In function `as3645a_remove':
leds-as3645a.c:(.text+0x784): undefined reference to `v4l2_flash_release'
This adds the same Kconfig dependency that the other V4L2 flash
drivers in drivers/leds use, to avoid that broken configuration.
Fixes: a56ba8fbcb ("media: leds: as3645a: Add LED flash class driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This should also allow probing to fail when a pca955x chip is not
found on a I2C bus.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In some systems, such as Baseboard Management Controllers (BMCs), we
want to retain the state of LEDs across a reboot of the BMC (whilst the
host remains up). Implement support for the retain-state-shutdown
devicetree property in leds-gpio.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Brandon Wyman <bjwyman@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Don't populate the arrays on the stack, instead make them static const.
Makes the object code smaller by 50 bytes:
Before:
text data bss dec hex filename
5058 1552 64 6674 1a12 drivers/leds/leds-lp8501.o
After:
text data bss dec hex filename
4788 1776 64 6628 19e4 drivers/leds/leds-lp8501.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Don't populate the arrays on the stack, instead make them static const.
Makes the object code smaller by over 150 bytes:
Before:
text data bss dec hex filename
7725 2448 64 10237 27fd drivers/leds/leds-lp5562.o
After:
text data bss dec hex filename
7184 2832 64 10080 2760 drivers/leds/leds-lp5562.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Don't populate the arrays on the stack, instead make them static const.
Makes the object code smaller by over 120 bytes:
Before:
text data bss dec hex filename
8999 4176 64 13239 33b7 drivers/leds/leds-lp5521.o
After:
text data bss dec hex filename
8554 4496 64 13114 333a drivers/leds/leds-lp5521.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Don't populate the array max_mm_current_percent on the stack, instead
make it static const. Makes the object code smaller by over 280 bytes:
Before:
text data bss dec hex filename
7225 1936 64 9225 2409 ./drivers/leds/leds-aat1290.o
After:
text data bss dec hex filename
6847 2032 64 8943 22ef ./drivers/leds/leds-aat1290.o`
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In case platform data provided empty LED name string the resulting
LED class device name would be crippled. Use corresponding LED chip
bit in place of "function" segment of LED class device name then to
make the LEDs at least distinguishable.
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Reported-by: Colin King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Nate Case <ncase@xes-inc.com>
Functions working with attribute_groups provided by <linux/device.h>
work with const attribute_group. These attribute_group structures do not
change at runtime so mark them as const.
File size before:
text data bss dec hex filename
8272 4608 64 12944 3290 drivers/leds/leds-lm3533.o
File size after:
text data bss dec hex filename
8368 4512 64 12944 3290 drivers/leds/leds-lm3533.o
This change was made with the help of Coccinelle.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Add a LED flash class driver for the as3654a flash controller. A V4L2 flash
driver for it already exists (drivers/media/i2c/as3645a.c), and this driver
is based on that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 flash interface allows controlling multiple LEDs through a single
sub-devices if, and only if, these LEDs are of different types. This
approach scales badly for flash controllers that drive multiple flash LEDs
or for LED specific associations. Essentially, the original assumption of a
LED driver chip that drives a single flash LED and an indicator LED is no
longer valid.
Address the matter by registering one sub-device per LED.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> (for greybus/light)
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The PCA955x family of chips are I2C LED blinkers whose pins not used
to control LEDs can be used as general purpose I/Os (GPIOs).
The following adds such a support by defining different operation
modes for the pins (See bindings documentation for more details). The
pca955x driver is then extended with a gpio_chip when some of pins are
operating as GPIOs. The default operating mode is to behave as a LED.
The GPIO support is conditioned by CONFIG_LEDS_PCA955X_GPIO.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This lets us remove the loop doing the cleanup in case of failure and
also the remove handler of the i2c_driver.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
It will be used in a following patch to define different operation
modes for each pin.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
for_each_child_of_node performs an of_node_get on each iteration, so a
return from the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,e1;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(e1,n) {
...
(
of_node_put(n);
|
e = n
|
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Merge conditionals that have the same then branch, to prepare for extending
that branch with of_node_put.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5JLc
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"This time we're removing more than adding:
Removed drivers:
leds-versatile:
- all users of the Versatile LED driver are deleted and replaced
with the very generic leds-syscon
leds-sead3:
- SEAD3 is using the generic leds-syscon & regmap based
register-bit-led driver
LED class drivers improvements:
ledtrig-gpio:
- use threaded IRQ, which both simplifies the code because we can
drop the workqueue indirection, and it enables using the trigger
for GPIOs that work with threaded IRQs themselves
- refresh LED state after GPIO change since the new GPIO may have
a different state than the old one
leds-lp55xx:
- make various arrays static const
leds-pca963x:
- add bindings to invert polarity"
* tag 'leds_for_4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: lp55xx: make various arrays static const
leds: Remove SEAD-3 driver
leds: trigger: gpio: Use threaded IRQ
leds: trigger: gpio: Refresh LED state after GPIO change
leds: Delete obsolete Versatile driver
leds: pca963x: Add bindings to invert polarity
Several arrays are currently on-stack and instead should be made
static const.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEbBAABAgAGBQJZR92EAAoJEHm+PkMAQRiGT1oH+KW2FLrRaYxtut+KyGA6l7tc
R/hFx1n9BibkjXeqD+y6/4SjRTe6/pT8Zkihv3/19eZ5algUWeQa0Hm+/455sl58
IdIXx/pzuCO3kqR3//fP9ZFD657GNDsuQ0fYnZESItFwiWQtO1TNfZD6KQjkqBdI
L3MVhDUVBZA2ZtPwC4ERei5/sToV9woykKoJ/A3+OkWjgX6w4SBimqgkSEFk4uE8
xS0pycyDZci93rJlECi1UueewdODTKSmhwdC80qvGEiYXzsC6UFtaF0Fj66XO1AL
UMjxqI/gkm5ZuCIjRsmPmJjgL5q1RT6UX/qtw9yn71XTmcgMiPW2/DF/v/OaTg==
=XbW2
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rc6' into patchwork
Linux 4.12-rc6
* tag 'v4.12-rc6': (813 commits)
Linux 4.12-rc6
mm: larger stack guard gap, between vmas
virtio_balloon: disable VIOMMU support
mm: correct the comment when reclaimed pages exceed the scanned pages
userfaultfd: shmem: handle coredumping in handle_userfault()
mm: numa: avoid waiting on freed migrated pages
swap: cond_resched in swap_cgroup_prepare()
mm/memory-failure.c: use compound_head() flags for huge pages
perf unwind: Report module before querying isactivation in dwfl unwind
fs: pass on flags in compat_writev
objtool: Add fortify_panic as __noreturn function
powerpc/debug: Add missing warn flag to WARN_ON's non-builtin path
USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks
drm: mxsfb_crtc: Reset the eLCDIF controller
drm/mgag200: Fix to always set HiPri for G200e4 V2
i2c: ismt: fix wrong device address when unmap the data buffer
i2c: rcar: use correct length when unmapping DMA
powerpc/xive: Fix offset for store EOI MMIOs
drm/tegra: Correct idr_alloc() minimum id
drm/tegra: Fix lockup on a use of staging API
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
SEAD3 is using the generic syscon & regmap based register-bit-led
driver as of commit c764583f40 ("MIPS: SEAD3: Use register-bit-led
driver via DT for LEDs") merged in the v4.9 cycle. As such the custom
SEAD-3 LED driver is now unused, so remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=GOju
-----END PGP SIGNATURE-----
Merge tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Two LED fixes:
- fix signal source assignment for leds-bcm6328
- revert patch that intended to fix LED behavior on suspend but it
had a side effect preventing suspend at all due to uevent being
sent on trigger removal"
* tag 'led_fixes_for_4.12-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
Revert "leds: handle suspend/resume in heartbeat trigger"
leds: bcm6328: fix signal source assignment for leds 4 to 7
This reverts commit 5ab92a7cb8.
System cannot enter suspend mode because of heartbeat led trigger.
In autosleep_wq, try_to_suspend function will try to enter suspend
mode in specific period. it will get wakeup_count then call pm_notifier
chain callback function and freeze processes.
Heartbeat_pm_notifier is called and it call led_trigger_unregister to
change the trigger of led device to none. It will send uevent message
and the wakeup source count changed. As wakeup_count changed, suspend
will abort.
Fixes: 5ab92a7cb8 ("leds: handle suspend/resume in heartbeat trigger")
Signed-off-by: Zhang Bo <bo.zhang@nxp.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Each nibble represents 4 LEDs, and in case of the higher register, bit 0
represents LED 4, so we need to use modulus for the LED number as well.
Fixes: fd7b025a23 ("leds: add BCM6328 LED driver")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
-----BEGIN PGP SIGNATURE-----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=+jBV
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-2' into patchwork
media fixes for v4.12-rc4
* tag 'media/v4.12-2': (598 commits)
[media] rc-core: race condition during ir_raw_event_register()
[media] cec: drop MEDIA_CEC_DEBUG
[media] cec: rename MEDIA_CEC_NOTIFIER to CEC_NOTIFIER
[media] cec: select CEC_CORE instead of depend on it
[media] rainshadow-cec: ensure exit_loop is intialized
[media] atomisp: don't treat warnings as errors
Linux 4.12-rc3
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
PCI/msi: fix the pci_alloc_irq_vectors_affinity stub
blk-mq: Only register debugfs attributes for blk-mq queues
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pass the more generic fwnode_handle to the init function than the
device_node.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This both simplifies the code because we can drop the workqueue
indirection, and it enables using the trigger for GPIOs that work with
threaded IRQs themselves.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The new GPIO may have a different state than the old one.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The driver checks an incorrect flag of functionality of adapter.
When a driver requires i2c_smbus_read_byte_data and
i2c_smbus_write_byte_data, it should check I2C_FUNC_SMBUS_BYTE_DATA
instead I2C_FUNC_I2C.
This patch fixes the problem.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
All users of the Versatile LED driver are deleted and replaced
with the very generic leds-syscon. Delete the old driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Add a new DT property, nxp,inverted-out, to invert the polarity
of the output.
Tested on PCA9634.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Fix typos and add the following to the scripts/spelling.txt:
momery||memory
Link: http://lkml.kernel.org/r/20170317011131.6881-1-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch extends the device tree support for the pca9532 by adding
the leds 'default-state' property.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Motorola CPCAP is a PMIC (power management integrated circuit) found
in multiple smartphones. This driver adds support for the chip's LED
controllers. This introduces support for all controllers used by the
Droid 4. According to Motorola's driver (no datasheets available)
there a couple of more LED controllers. I did not add support for
them, since I cannot verify that they work with my modifications.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Instead of unusual "if (!ret)" use "if (ret)" in lp3952_get_label().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In ACPI world any ID should be carefully chosen and registered
officially. The discussion [1] as I read it gets to wilful assignment
an ID for non-existing real DSDT example.
Rafael already told [2] how this device would be enumerated using
compatible string. To be more precise look at the possible DSDT excerpt
below:
Device (LDX0) {
Name (_HID, "PRP0001")
Name (_DDN, "TI LP3952 compatible led driver")
...
})
Name (_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"compatible", "ti,lp3952"},
...
}
})
Based on above, remove non-official ACPI IDs and enumeration from the
driver.
Note: currently driver has no compatible strings at all, to make above
working one should add at least one.
[1] https://e2e.ti.com/support/power_management/led_driver/f/192/t/524926
[2] https://www.spinics.net/lists/linux-acpi/msg67125.html
Cc: Tony Makkiel <tony.makkiel@daqri.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
It should be ">= MT6323_MAX_LEDS" instead of ">". Also "reg" is a u32
so it can't be negative and we can remove the test for negative values.
Fixes: 216ec6cc4c ("leds: Add LED support for MT6323 PMIC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
MT6323 PMIC is a multi-function device that includes LED function.
It allows attaching up to 4 LEDs which can either be on, off or dimmed
and/or blinked with the controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
In leds-gpio we support LEDs specified in DT so we should use
(devm_)of_led_classdev_register. This allows passing DT node as argument
for use by the LED subsystem.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
These new functions allow passing an additional device_node argument
that will be internally set for created LED device. Thanks to this LED
core code and triggers will be able to access DT node for reading extra
info.
The easiest solution for achieving this was reworking old functions to
more generic ones & adding simple defines for API compatibility.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The dell-led driver handles a specific WMI GUID present on some Dell
laptops and as such it belongs in the x86 platform driver subsystem.
Source code is moved along with the relevant Kconfig and Makefile
entries, with some minor modifications:
- Kconfig option is renamed from CONFIG_LEDS_DELL_NETBOOKS to
CONFIG_DELL_WMI_LED,
- the X86 Kconfig dependency is removed as the whole
drivers/platform/x86 menu depends on it, so there is no need to
duplicate it,
- the name of the module's source file is removed from the header
comment to avoid the need to update it in the future.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
With dell_micmute_led_set() moved to drivers/platform/x86/dell-laptop.c,
all remnants of the mic mute LED handling code can be removed from
drivers/leds/dell-led.c, restoring it back to the state it was in before
commit db6d8cc007 ("dell-led: add mic mute led interface").
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
To ensure all users of dell-smbios are in drivers/platform/x86, move the
dell_micmute_led_set() method from drivers/leds/dell-led.c to
drivers/platform/x86/dell-laptop.c.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The dell_app_wmi_led_set() method introduced in commit db6d8cc007
("dell-led: add mic mute led interface") was implemented as an easily
extensible entry point for other modules to set the state of various
LEDs. However, almost three years later it is still only used to
control the mic mute LED, so it will be replaced with direct calls to
dell_micmute_led_set().
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
As dell_micmute_led_set() no longer uses the dell_wmi_perform_query()
method, which was removed in commit 0c41a08e13 ("dell-led: use
dell_smbios_send_request() for performing SMBIOS calls"), the
DELL_APP_GUID check is redundant and thus can be safely removed.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Currently there is one CPU led trigger per cpu ('cpu0', 'cpu1', ...)
This patch adds a new trigger, 'cpu', with brightness proportional to
the number of active CPUs.
If multiple brightness levels aren't supported on the LED,
it effectively indicates if there is any CPU active.
This is particularly useful on tiny linux boards with more CPU cores than LED pins.
Signed-off-by: Paulo Costa <me@paulo.costa.nom.br>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
We are going to split <linux/sched/loadavg.h> out of <linux/sched.h>, which
will have to be picked up from a couple of .c files.
Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This set contains mostly fixes to existing drivers as well as cleanup of
code that's not been in active use for a while.
-----BEGIN PGP SIGNATURE-----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=J9q4
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set contains mostly fixes to existing drivers as well as cleanup
of code that's not been in active use for a while"
* tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (27 commits)
acpi: lpss: call pwm_add_table() for BSW PWM device
pwm: Try to load modules during pwm_get()
pwm: Don't hold pwm_lookup_lock longer than necessary
pwm: Make the PWM_POLARITY flag in DTB optional
pwm: Print error messages with pr_err() instead of pr_debug()
pwm: imx: Add polarity inversion support to i.MX's PWMv2
pwm: imx: doc: Update imx-pwm.txt documentation entry
pwm: imx: Remove redundant i.MX PWMv2 code
pwm: imx: Provide atomic PWM support for i.MX PWMv2
pwm: imx: Move PWMv2 wait for fifo slot code to a separate function
pwm: imx: Move PWMv2 software reset code to a separate function
pwm: imx: Rewrite v1 code to facilitate switch to atomic PWM
pwm: imx: Add separate set of PWM ops for v1 and v2
pwm: imx: Remove ipg clock and enable per clock when required
pwm: lpss: Add Intel Gemini Lake PCI ID
pwm: lpss: Do not export board infos for different PWM types
pwm: lpss: Avoid reconfiguring while UPDATE bit is still enabled
pwm: lpss: Switch to new atomic API
pwm: lpss: Allow duty cycle to be 0
pwm: lpss: Avoid potential overflow of base_unit
...
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do.
This is a treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace
ABI correctly reflect the current in-kernel consumer of a pin
taken using this abstraction. This is a treewide change also
updating all users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide
change also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing
a backend into the pin control subsystem that were also merged
into the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace
to fully test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime
PM support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations.
-----BEGIN PGP SIGNATURE-----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=O81I
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.11 cycle
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do. This is a
treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace ABI
correctly reflect the current in-kernel consumer of a pin taken
using this abstraction. This is a treewide change also updating all
users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide change
also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing a
backend into the pin control subsystem that were also merged into
the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace to fully
test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime PM
support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations"
* tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: reintroduce devm_get_gpiod_from_child()
gpio: pci-idio-16: Fix PCI BAR index
gpio: pci-idio-16: Fix PCI device ID code
gpio: mockup: implement event injecting over debugfs
gpio: mockup: add a dummy irqchip
gpio: mockup: implement naming the lines
gpio: mockup: code shrink
gpio: mockup: readability tweaks
gpio: Add GPIO support for the ACCES PCI-IDIO-16
gpio: Add the devm_fwnode_get_index_gpiod_from_child() helper
gpio: Rename devm_get_gpiod_from_child()
gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error
gpio: ws16c48: Add support for GPIO names
gpio: gpio-mm: Add support for GPIO names
gpio: 104-idio-16: Add support for GPIO names
gpio: 104-idi-48: Add support for GPIO names
gpio: 104-dio-48e: Add support for GPIO names
gpio: ws16c48: Remove unnecessary driver_data set
gpio: gpio-mm: Remove unnecessary driver_data set
gpio: 104-idio-16: Remove unnecessary driver_data set
...
LED class heartbeat trigger allowed only for blinking with max_brightness
value. This patch adds more flexibility by exploiting part of LED core
software blink infrastructure.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Rename devm_get_gpiod_from_child() into
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some LEDs may have their brightness level changed autonomously
(outside of kernel control) by hardware / firmware. This commit
adds support for an optional brightness_hw_changed attribute to
signal such changes to userspace (if a driver can detect them):
What: /sys/class/leds/<led>/brightness_hw_changed
Date: January 2017
KernelVersion: 4.11
Description:
Last hardware set brightness level for this LED. Some LEDs
may be changed autonomously by hardware/firmware. Only LEDs
where this happens and the driver can detect this, will
have this file.
This file supports poll() to detect when the hardware
changes the brightness.
Reading this file will return the last brightness level set
by the hardware, this may be different from the current
brightness.
Drivers which want to support this, simply add LED_BRIGHT_HW_CHANGED to
their flags field and call led_classdev_notify_brightness_hw_changed()
with the hardware set brightness when they detect a hardware / firmware
triggered brightness change.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
gcc gets confused about the control flow in ktd2692_parse_dt(), causing
it to warn about what seems like a potential bug:
drivers/leds/leds-ktd2692.c: In function 'ktd2692_probe':
drivers/leds/leds-ktd2692.c:244:15: error: '*((void *)&led_cfg+8)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:225:7: error: 'led_cfg.flash_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:232:3: error: 'led_cfg.movie_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is fine, and slightly reworking it in an equivalent way lets
gcc figure that out too, which gets rid of the warning.
Fixes: 77e7915b15 ("leds: ktd2692: Add missing of_node_put")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Currently all users of fwnode_get_named_gpiod() have no way to
specify a label for the GPIO. So GPIOs listed in debugfs are shown
with label "?". With this change a proper label is used.
Also adjust all users so they can pass a label, properly retrieved
from device tree properties.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make fwnode_get_named_gpiod() consistent with the rest of
gpiod_get() like API, i.e. configure GPIO pin immediately after
request.
Besides obvious clean up it will help to configure pins based
on firmware provided resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PWM devices have all been marked as "might sleep" since v4.5. It no
longer makes sense to keep the alternative code paths around because
it is effectively dead code.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch enables ACPI support for leds-pca955x driver.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/leds//leds-netxbig.ko | grep alias
alias: platform:leds-netxbig
After this patch:
$ modinfo drivers/leds//leds-netxbig.ko | grep alias
alias: platform:leds-netxbig
alias: of:N*T*Clacie,netxbig-ledsC*
alias: of:N*T*Clacie,netxbig-leds
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch enables ACPI support for leds-pca963x driver.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
All 3 of led_timer_func, led_set_brightness and led_set_software_blink
set blink_brightness. If led_timer_func or led_set_software_blink race
with led_set_brightness they may end up overwriting the new
blink_brightness. The new atomic work_flags does not protect against
this as it just protects the flags and not blink_brightness.
This commit introduces a new new_blink_brightness value which gets
set by led_set_brightness and read by led_timer_func on LED on, fixing
this.
Dealing with the new brightness at LED on time, makes the new
brightness apply sooner, which also fixes a led_set_brightness which
happens while a oneshot blink which ends in LED on is running not
getting applied.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
All the LED_BLINK* flags are accessed read-modify-write from e.g.
led_set_brightness and led_blink_set_oneshot while both
set_brightness_work and the blink_timer may be running.
If these race then the modify step done by one of them may be lost,
switch the LED_BLINK* flags to a new atomic work_flags bit-field
to avoid this race.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Add the driver to support User LEDs on PXI Embedded Controller.
Signed-off-by: Hui Chun Ong <hui.chun.ong@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Verify that vendor is Mellanox as the first step of initialization.
If it is not - return ENODEV.
Change module license from "GPL v2" to "Dual BSD/GPL".
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Allow chip to enter low power state when no LEDs are being lit or in
blink mode.
Cc: Peter Meerwald <p.meerwald@bct-electronic.com>,
Cc: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The value for a led's default_trigger should come from platform data
instead of data (which is always 0).
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
PCA9632TK part seems to incorrectly blink at ~1.3x of the programmed
rate. This patchset add a nxp,period-scale devicetree property to
adjust for this misconfiguration.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
If the driver is built as a module, I2C module alias information is not
filled so the module won't be autoloaded if the device isn't registered
over ACPI. Export the I2C device table alias with MODULE_DEVICE_TABLE()
macro so the information is exported in the module.
Before this patch:
$ modinfo drivers/leds/leds-lp3952.ko | grep alias
alias: acpi*:TXNW3952:*
After this patch:
$ modinfo drivers/leds/leds-lp3952.ko | grep alias
alias: i2c:lp3952
alias: acpi*:TXNW3952:*
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Fix the register access shift argument calculation introduced with
commit a59ce6584d ("leds: leds-mc13783: Add MC34708 LED support")
and re-enable access to the "keypad" led for MC13892 MFC devices.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use a macro instead of hard-coding the max device node name size. The
uleds driver introduced a macro for this value, so using it.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This driver creates a userspace leds driver similar to uinput.
New LEDs are created by opening /dev/uleds and writing a uleds_user_dev
struct. A new LED class device is registered with the name given in the
struct. Reading will return a single byte that is the current brightness.
The poll() syscall is also supported. It will be triggered whenever the
brightness changes. Closing the file handle to /dev/uleds will remove
the leds class device.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The Kconfig and file naming for the PM8xxx driver is totally
confusing:
- Kconfig options MFD_PM8XXX and MFD_PM8921_CORE, some in-kernel
users depending on or selecting either at random.
- A driver file named pm8921-core.c even if it is indeed
used by the whole PM8xxx family of chips.
- An irqchip named pm8xxx since it was (I guess) realized that
the driver was generic for all pm8xxx PMICs.
As I may want to add support for PM8901 this is starting to get
really messy. Fix this situation by:
- Remove the MFD_PM8921_CORE symbol and rely solely on MFD_PM8XXX
and convert all users, including LEDs Kconfig and ARM defconfigs
for qcom and multi_v7 to use that single symbol.
- Renaming the driver to qcom-pm8xxx.c to fit along the two
other qcom* prefixed drivers.
- Rename functions withing the driver from 8921 to 8xxx to
indicate it is generic.
- Just drop the =m config from the pxa_defconfig, I have no clue
why it is even there, it is not a Qualcomm platform. (Possibly
older Kconfig noise from saveconfig.)
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If led_trigger_set() is called with "trig" argument set to NULL, and there
is no trigger to remove then the function should return immediately so
as to avoid doing unnecessary allocation and sending uevent.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: Daniel Romell <daro@hms.se>
Acked-by Daniel Romell <daro@hms.se>
Simplify the error handling and add a missing call to fwnode_handle_put
when checking led.name.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Using the managed version of led_classdev_register allows to
significantly simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Checking for the presence of the property first isn't strictly needed
as we can react on the return code of fwnode_property_read_string.
Also, even if the presence of a property "label" was checked,
reading a string value for it theoretically still can fail and
this case isn't handled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Definition of np can be moved into the loop as well to simplify
the code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Add a helper for the container_of as it's used more than once.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
gpiod_get_value_cansleep returns 0, 1, or an error code.
So far errors are not handled and treated the same as 1.
Change this to bail out if an error code is returned and
remove the double negation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Introduce a typedef gpio_blink_set_t to improve readability of the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This makes it possible to create a set of LEDs for Mellanox systems:
"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410",
"msb7800", "msn2740", "msn2100".
Driver obtains LED devices according to system configuration, provided
through system DMI data, like mlxcpld:fan1:green, mlxcpld:fan1:red and
creates devices in form: "devicename:colour:function".
LED setting is controlled through on board CPLD Lattice device.
For setting particular LED off, solid, blink:
echo 0 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo timer > /sys/class/leds/mlxcpld\:status\:green/trigger
On module probing all LEDs are set green, on removing - off.
Last setting overwrites previous, f.e. sequence for
changing LED from green - red - green:
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:red/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
Note: LEDs cannot be turned on/off simultaneously.
The Kconfig currently controlling compilation of this code is:
drivers/leds/Kconfig:config LEDS_MLXCPLD
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This adds a driver for the six PM8058 LEDs, three ordinary LEDs,
two "flash" LEDs and one "keypad" LED.
The "keypad" and "flash" LEDs are not really hard-wired to these
usecases: for example on the APQ8060 Dragonboard, the "keypad"
LED is instead used to drive an IR LED used for the proximity
sensor. The "flash" LEDs are just ordinary high-current LED
drivers.
Cc: linux-arm-msm@vger.kernel.org
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Per the documentation, use scnprintf instead of sprintf to ensure there
is never more than PAGE_SIZE bytes of trigger names put into the
buffer.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The Kconfig currently controlling compilation of this code is:
drivers/leds/trigger/Kconfig:menuconfig LEDS_TRIGGERS
drivers/leds/trigger/Kconfig: bool "LED Trigger support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file doesn't need that.
However it does use EXPORT_SYMBOL, so we add the export.h header.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This is a driver for the Integrated Silicon Solution Inc. LED driver
chips series IS31FL319x. They can drive 1, 3, 6 or up to 9
LEDs.
Each LED is individually controllable in brightness (through pwm)
in 256 steps so that RGB LEDs can show any of ca. 16 Mio colors.
The maximum current of the LEDs can be programmed and limited to
5 .. 40mA through a device tree property.
The chip is connected through I2C and can have one of 4 addresses
in the range 0x64 .. 0x67 depending on how the AD pin is connected. The
address is defined by the reg property as usual.
The chip also has a shutdown input which could be connected to a GPIO,
but this driver uses software shutdown if all LEDs are inactivated.
The chip also has breathing and audio features which are not fully
supported by this driver.
Tested-on: OMAP5 based Pyra handheld prototype.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXnWchAAoJEFHr6jzI4aWAe64P/36Vd9yJLptjkoyZp8/IQtu1
Cv8buQwGdKuSMzdkcUAOXcC3fe2u70ZWXMKKLfY3koIV1IAiqdWk5/XWRKMP2XmE
dG0LhSf0uu7uh+mE0WvQnRu46ImeKtQ+mPp4Hbs/s9SxMSeYjruv3vdWWmgUq0cl
Gac2qJSRtAMmgLuHWMjf7N5mxOTOnKejU4o2i9cJ+YHmWKOdCigv2Ge1UadOQFlC
E7tRPiUR3asfDfj+e+LVTTdToH6p8pk+mOUzIoZ8jIkQ+IXzi62UDl5+Rw9mqiuX
1CtqEMUXxo2qwX+d4TcV/QUOp0YKPuIcUZ9NMMS+S3lOyJ4NFt+j2Izk7QJp5kNP
gKVqB68TjDQsBuDr3P9ynlHbduxTIhZAqopbTrLe0FIg48nUe4n1yHJBVzqaVajX
rFBJSsSUffBLAARNPSXJJhIgc2C1/qOC8dgMeDMcR2kPirDHaQZ/lY1yEpq1yiqR
q6e3v5hvIAm4IjbYk0mF7TUxBrPGVE/ExyBINyASRoYxAJ1PyeD/iljZ9vI3asRA
s+hhxT8H3f7lnqTrmJqMjHgAdGkmag07EdmvFNX4xK4aADSy7Y6g4dw25ffRopo9
p9Jf9HX+dZv65Y3UjbV/6HuXcaSEBJJLSVWvii65PebqSN0LuHEFvNeIJ6Iblx0B
AWh/hd0Iin2gdkcG39Mr
=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
There is no need the ledtriger to be called *that* early in the hotplug
process (+ with disabled interrupts). As explained by Jacek Anaszewski [0]
there is no need for it.
Therefore this patch moves it to the ONLINE/PREPARE_DOWN level using the
dynamic registration for the id.
[0] https://lkml.kernel.org/r/578C92BC.2070603@samsung.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: rt@linutronix.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-leds@vger.kernel.org
Link: http://lkml.kernel.org/r/1469028295-14702-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Otherwise the driver module will not be automatically probed.
Fixes: 9d7cffaf99 ("leds: Add driver for the ISSI IS31FL32xx family of LED controllers")
Fixes: e0442d7def ("leds: Add SN3218 and SN3216 support to the IS31FL32XX driver")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: David Rivshin <drivshin@allworx.com>
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: David Rivshin <drivshin@allworx.com>
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The chip can drive 2 sets of RGB leds. Controller can
be controlled via PWM, I2C and audio synchronisation.
This driver uses I2C to communicate with the chip.
Datasheet: http://www.ti.com/lit/gpn/lp3952
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This is a straightforward conversion. We place this callback last
in the list so that the LED illuminates only after a successful
bring up sequence.
( NOTE: The patch adds a FIXME question about the callback used,
this question should probably be revisited later on.)
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-leds@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.465496902@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When working with Device Tree we iterate over children of "gpio-leds"
compatible node and create LED device for each of them. We take care of
all common DT properties (label, default trigger, state, etc.), however
some triggers may want to support more of them.
It could be useful for timer trigger to support setting delay on/off
values with Device Tree property. Or for transient trigger to support
e.g. duration property.
We obviously should handle such properties in triggers, not in generic
code. To let trigger drivers read properties from DT node we need to set
of_node to point the relevant node. This change allows using all kind of
of helpers in e.g. "activate" callbacks.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
If an invalid trigger name is provided via sysfs currently no error
is returned. Therefore it's not possible to determine whether the
trigger was set successfully.
Fix this by returning -EINVAL if no trigger is matched.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
An opal_msg of type OPAL_MSG_ASYNC_COMP contains the return code in the
params[1] struct member. However this isn't intuitive or obvious when
reading the code and requires that a user look at the skiboot
documentation or opal-api.h to verify this.
Add an inline function to get the return code from an opal_msg and update
call sites accordingly.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This patch adds basic device tree support for the pca9532 LEDs.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The following phenomena was observed: when suspending the
system, sometimes the heartbeat LED was left on, glowing and
wasting power while the rest of the system is asleep, also
disturbing power dissapation measures on the odd suspend
cycle when it's left on.
Clearly this is not how we want the heartbeat trigger to
work: it should turn off and leave the LED off during
system suspend.
This removes the heartbeat trigger when preparing suspend and
restores it during resume. The trigger code will make sure all
LEDs are left in OFF state after removing the trigger, and
will re-enable the trigger on all LEDs after resuming.
Cc: linux-pm@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Commit 76931edd54 ("leds: fix brightness changing when software blinking
is active") changed the semantics of led_set_brightness() which according
to the documentation should disable blinking upon any brightness setting.
Moreover it made it different for soft blink case, where it was possible
to change blink brightness, and for hardware blink case, where setting
any brightness greater than 0 was ignored.
While the change itself is against the documentation claims, it was driven
also by the fact that timer trigger remained active after turning blinking
off. Fixing that would have required major refactoring in the led-core,
led-class, and led-triggers because of cyclic dependencies.
Finally, it has been decided that allowing for brightness change during
blinking is beneficial as it can be accomplished without disturbing
blink rhythm.
The change in brightness setting semantics will not affect existing
LED class drivers that implement blink_set op thanks to the LED_BLINK_SW
flag introduced by this patch. The flag state will be from now on checked
in led_set_brightness() which will allow to distinguish between software
and hardware blink mode. In the latter case the control will be passed
directly to the drivers which apply their semantics on brightness set,
which is disable the blinking in case of most such drivers. New drivers
will apply new semantics and just change the brightness while hardware
blinking is on, if possible.
The issue was smuggled by subsequent LED core improvements, which modified
the code that originally introduced the problem.
Fixes: f1e80c0741 ("leds: core: Add two new LED_BLINK_ flags")
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This set of changes introduces an atomic API to the PWM subsystem. This
is influenced by the DRM atomic API that was introduced a while back,
though it is obviously a lot simpler. The fundamental idea remains the
same, though: drivers provide a single callback to implement the atomic
configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware. Many
use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are postponed
to v4.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sxT9
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces an atomic API to the PWM subsystem.
This is influenced by the DRM atomic API that was introduced a while
back, though it is obviously a lot simpler. The fundamental idea
remains the same, though: drivers provide a single callback to
implement the atomic configuration of a PWM channel.
As a side-effect the PWM subsystem gains the ability for initial state
retrieval, so that the logical state mirrors that of the hardware.
Many use-cases don't care about this, but for others it is essential.
These new features require changes in all users, which these patches
take care of. The core is transitioned to use the atomic callback if
available and provides a fallback mechanism for other drivers.
Changes to transition users and drivers to the atomic API are
postponed to v4.8"
* tag 'pwm/for-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
pwm: Add information about polarity, duty cycle and period to debugfs
pwm: Switch to the atomic API
pwm: Update documentation
pwm: Add core infrastructure to allow atomic updates
pwm: Add hardware readout infrastructure
pwm: Move the enabled/disabled info into pwm_state
pwm: Introduce the pwm_state concept
pwm: Keep PWM state in sync with hardware state
ARM: Explicitly apply PWM config extracted from pwm_args
drm: i915: Explicitly apply PWM config extracted from pwm_args
input: misc: pwm-beeper: Explicitly apply PWM config extracted from pwm_args
input: misc: max8997: Explicitly apply PWM config extracted from pwm_args
backlight: lm3630a: explicitly apply PWM config extracted from pwm_args
backlight: lp855x: Explicitly apply PWM config extracted from pwm_args
backlight: lp8788: Explicitly apply PWM config extracted from pwm_args
backlight: pwm_bl: Use pwm_get_args() where appropriate
fbdev: ssd1307fb: Use pwm_get_args() where appropriate
regulator: pwm: Use pwm_get_args() where appropriate
leds: pwm: Use pwm_get_args() where appropriate
input: misc: max77693: Use pwm_get_args() where appropriate
...
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Calling a GPIO LEDs is quite likely to work even if the kernel
has paniced, so they are ideal to blink in this situation.
This commit adds support for the new "panic-indicator"
firmware property, allowing to mark a given LED to blink on
a kernel panic.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit adds a new led_cdev flag LED_PANIC_INDICATOR, which
allows to mark a specific LED to be switched to the "panic"
trigger, on a kernel panic.
This is useful to allow the user to assign a regular trigger
to a given LED, and still blink that LED on a kernel panic.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The Intel NAS SS4200 was also sold by Fujitsu Siemens (FSC) under
the name "SCALEO Home Server". The hardware is equivalent.
This patch adds the DMI data of this rebranded device.
Signed-off-by: Martin Dummer <martin.dummer@gmx.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
There is only one x86 hardware where the driver leds-ss4200 applies to.
Add kconfig dependency to x86 architecture, fix help text whitespace.
Signed-off-by: Martin Dummer <martin.dummer@gmx.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Parameters delay_on and delay_off of led_trigger_blink_oneshot()
are pointers, to enable blink interval adjustment by LED class drivers
of the controllers that implement hardware blinking.
Move ide_blink_delay variable to ledtrig_ide_activity() in order to
prevent the situation when adjustment committed by one LED class
driver influences blink interval of the software fallback blink feature,
that is applied to the drivers that don't implement blink_set op.
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
If choose_times() returns -EINVAL that means "c1" and "c2" haven't been
initialized. I've added a check for that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit introduces a MTD trigger for flash (NAND/NOR) device
activity. The implementation is copied from IDE disk.
This trigger deprecates the "nand-disk" LED trigger, but for backwards
compatibility, we still keep the "nand-disk" trigger around.
The motivation for deprecating the "nand-disk" LED trigger is that
it only works for NAND drivers, whereas the "mtd" LED trigger
is more generic (in fact, "nand-disk" currently only works for
certain NAND drivers).
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit introduces a new LED trigger which allows to configure
a LED to blink on a kernel panic (through panic_blink).
Notice that currently the Openmoko FreeRunner (GTA02) mach code
sets panic_blink to blink a hard-coded LED. The new trigger is
meant to introduce a generic mechanism to achieve this.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Significant refactoring of Dell laptop drivers, modularizing the smbios code.
Multiple new platforms added for ideapad, asus, dell, and alienware using
existing quirks. A few fixes and cleanups.
hp-wmi:
- Remove GPS rfkill support via pre-2009 interface
- fix unregister order in hp_wmi_rfkill_setup() once again
ideapad-laptop:
- Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop:
- Support radio toggle button
intel-hid:
- allocate correct amount of memory for private struct
platform/x86:
- Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc:
- Avoid pending IPC1 command during legacy suspend
- Fix GCR register base address and length
asus-nb-wmi:
- add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv:
- Change verbosity control bits
dell-rbtn:
- Add a comment about the XPS 13 9350
dell-wmi, dell-laptop:
- depends DMI
dell-wmi:
- support Dell Inspiron M5110
- properly process Dell Instant Launch hotkey
- enable receiving WMI events on Dell Vostro V131
- Support new hotkeys on the XPS 13 9350 (Skylake)
- Clean up hotkey table size check
- Stop storing pointers to DMI tables
dell-laptop:
- move dell_smi_error() to dell-smbios
- use dell_smbios_find_token() instead of find_token_location()
- use dell_smbios_find_token() instead of find_token_id()
- extract SMBIOS-related code to a separate module
dell-smbios:
- rename dell_smi_error() to dell_smbios_error()
- make da_tokens static
- remove find_token_{id,location}()
- implement new function for finding DMI table 0xDA tokens
- make the SMBIOS buffer static
- return the SMBIOS buffer from dell_smbios_get_buffer()
- don't return an SMBIOS buffer from dell_smbios_send_request()
- don't pass an SMBIOS buffer to dell_smbios_send_request()
- rename dell_send_request() to dell_smbios_send_request()
- rename release_buffer() to dell_smbios_release_buffer()
- rename clear_buffer() to dell_smbios_clear_buffer()
- rename get_buffer() to dell_smbios_get_buffer()
dell-led:
- use dell_smbios_send_request() for performing SMBIOS calls
- use dell_smbios_find_token() for finding mic DMI tokens
toshiba_acpi:
- Add a module parameter to disable hotkeys registration
- Add sysfs entries for the Cooling Method feature
- Add support for cooling method feature
Documentation/ABI:
- Update sysfs-driver-toshiba_acpi file
thinkpad_acpi:
- Remove ambiguous logging for "Unsupported brightness interface"
alienware-wmi:
- whitespace improvements
- Add support for two new systems: ASM200 and ASM201.
- Add support for deep sleep control.
- Add initial support for alienware graphics amplifier.
- Add support for new platform: X51-R3
- Clean up whitespace for ASM100 platform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW8s77AAoJEKbMaAwKp364iVgH/18Tpefbc7uOrNak4zfTmvVO
CQjLdbnbCYoeNjwgdYSZNlaR+E2TuMdqmBXXLEr3kqicpmX15l+V5y8xJkDmGpxw
0RmwJnkdIpmkZcjb3/2abOtIuOj1Y/tXCp5mY1FoaDYBQVzO+ZsPEGNQcMu5uJpa
qZTw9UwiSPUspTrHHbS7/Bzv7yFnxlWC1nmt6G5zL4OMEv2AGbuVSstXVGySIML5
TfFdisUBIXQplzwpDytHGqtGUJMc0NnT1s66beuo1oBdEFTFtBNpFySW3goV2nrZ
JPbvyaV3tD24NYNmU9WH653InX4KuaGiJRWVT31a/I5HVVlx7mZdUYRI+EYAnmE=
=e0E4
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.6-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Significant refactoring of Dell laptop drivers, modularizing the
smbios code. Multiple new platforms added for ideapad, asus, dell,
and alienware using existing quirks. A few fixes and cleanups.
hp-wmi:
- Remove GPS rfkill support via pre-2009 interface
- fix unregister order in hp_wmi_rfkill_setup() once again
ideapad-laptop:
- Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop:
- Support radio toggle button
intel-hid:
- allocate correct amount of memory for private struct
platform/x86:
- Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc:
- Avoid pending IPC1 command during legacy suspend
- Fix GCR register base address and length
asus-nb-wmi:
- add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv:
- Change verbosity control bits
dell-rbtn:
- Add a comment about the XPS 13 9350
dell-wmi, dell-laptop:
- depends DMI
dell-wmi:
- support Dell Inspiron M5110
- properly process Dell Instant Launch hotkey
- enable receiving WMI events on Dell Vostro V131
- Support new hotkeys on the XPS 13 9350 (Skylake)
- Clean up hotkey table size check
- Stop storing pointers to DMI tables
dell-laptop:
- move dell_smi_error() to dell-smbios
- use dell_smbios_find_token() instead of find_token_location()
- use dell_smbios_find_token() instead of find_token_id()
- extract SMBIOS-related code to a separate module
dell-smbios:
- rename dell_smi_error() to dell_smbios_error()
- make da_tokens static
- remove find_token_{id,location}()
- implement new function for finding DMI table 0xDA tokens
- make the SMBIOS buffer static
- return the SMBIOS buffer from dell_smbios_get_buffer()
- don't return an SMBIOS buffer from dell_smbios_send_request()
- don't pass an SMBIOS buffer to dell_smbios_send_request()
- rename dell_send_request() to dell_smbios_send_request()
- rename release_buffer() to dell_smbios_release_buffer()
- rename clear_buffer() to dell_smbios_clear_buffer()
- rename get_buffer() to dell_smbios_get_buffer()
dell-led:
- use dell_smbios_send_request() for performing SMBIOS calls
- use dell_smbios_find_token() for finding mic DMI tokens
toshiba_acpi:
- Add a module parameter to disable hotkeys registration
- Add sysfs entries for the Cooling Method feature
- Add support for cooling method feature
Documentation/ABI:
- Update sysfs-driver-toshiba_acpi file
thinkpad_acpi:
- Remove ambiguous logging for "Unsupported brightness interface"
alienware-wmi:
- whitespace improvements
- Add support for two new systems: ASM200 and ASM201.
- Add support for deep sleep control.
- Add initial support for alienware graphics amplifier.
- Add support for new platform: X51-R3
- Clean up whitespace for ASM100 platform"
* tag 'platform-drivers-x86-v4.6-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (47 commits)
hp-wmi: Remove GPS rfkill support via pre-2009 interface
hp-wmi: fix unregister order in hp_wmi_rfkill_setup() once again
dell-wmi: support Dell Inspiron M5110
dell-wmi: properly process Dell Instant Launch hotkey
dell-wmi: enable receiving WMI events on Dell Vostro V131
dell-smbios: rename dell_smi_error() to dell_smbios_error()
dell-laptop: move dell_smi_error() to dell-smbios
ideapad-laptop: Add ideapad Y700 (15) to the no_hw_rfkill DMI list
fujitsu-laptop: Support radio toggle button
intel-hid: allocate correct amount of memory for private struct
platform/x86: Make intel_scu_ipc explicitly non-modular
intel_pmc_ipc: Avoid pending IPC1 command during legacy suspend
intel_pmc_ipc: Fix GCR register base address and length
asus-nb-wmi: add wapf=4 quirk for ASUS X75VD
intel_telemetry_pltdrv: Change verbosity control bits
dell-rbtn: Add a comment about the XPS 13 9350
dell-wmi: Support new hotkeys on the XPS 13 9350 (Skylake)
dell-wmi: Clean up hotkey table size check
dell-wmi, dell-laptop: depends DMI
dell-wmi: Stop storing pointers to DMI tables
...
Instead of using the WMI wrapper, dell-led can take advantage of
dell_smbios_send_request() for performing the SMBIOS calls required to
change the state of the microphone LED.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
With the advent of dell_smbios_find_token(), dell-led does not need to
perform any DMI walking on its own, but it can rather ask dell-smbios to
look up the DMI tokens it needs for changing the state of the microphone
LED.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
led_trigger_store can be significantly simplified by using sysfs_streq().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, max8997_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, da903x_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove unnecessary function pdev_to_gpio, platform_set_drvdata
in the probe function and the remove function, s3c24xx_led_remove as
it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata from probe function and the remove
function, wm831x_status_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, lp8788_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
Also, remove platform_set_drvdata in probe function and the remove
function, pm860x_led_remove as it is now has nothing to do.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Si-En Technology was acquired by ISSI in 2011, and it appears that
the IS31FL3218/IS31FL3216 are just rebranded SN3218/SN3216 devices.
Add the "si-en,sn3218" and "si-en,sn3216" compatible strings into the
IS31FL32XX driver as aliases for the issi equivalents, and update
binding documentation.
Datasheets:
IS31FL3218: http://www.issi.com/WW/pdf/31FL3218.pdf
SN3218: http://www.si-en.com/uploadpdf/s2011517171720.pdf
IS31FL3216: http://www.issi.com/WW/pdf/31FL3216.pdf
SN3216: http://www.si-en.com/uploadpdf/SN3216201152410148.pdf
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The IS31FL32xx family of LED controllers are I2C devices with multiple
constant-current channels, each with independent 256-level PWM control.
Datasheets: http://www.issi.com/US/product-analog-fxled-driver.shtml
This has been tested on the IS31FL3236 and IS31FL3216, on an ARM
(TI am335x) platform.
The programming paradigm of these devices is similar in the following
ways:
- All registers are 8 bit
- All LED control registers are write-only
- Each LED channel has a PWM register (0-255)
- PWM register writes are shadowed until an Update register is poked
- All have a concept of Software Shutdown, which disables output
However, there are some differences in devices:
- 3236/3235 have a separate Control register for each LED,
(3218/3216 pack the enable bits into fewer registers)
- 3236/3235 have a per-channel current divisor setting
- 3236/3235 have a Global Control register that can turn off all LEDs
- 3216 is unique in a number of ways
- OUT9-OUT16 can be configured as GPIOs instead of LED controls
- LEDs can be programmed with an 8-frame animation, with
programmable delay between frames
- LEDs can be modulated by an input audio signal
- Max output current can be adjusted from 1/4 to 2x globally
- Has a Configuration register instead of a Shutdown register
This driver currently only supports the base PWM control function
of these devices. The following features of these devices are not
implemented, although it should be possible to add them in the future:
- All devices are capable of going into a lower-power "software
shutdown" mode.
- The is31fl3236 and is31fl3235 can reduce the max output current
per-channel with a divisor of 1, 2, 3, or 4.
- The is31fl3216 can use some LED channels as GPIOs instead.
- The is31fl3216 can animate LEDs in hardware.
- The is31fl3216 can modulate LEDs according to an audio input.
- The is31fl3216 can reduce/increase max output current globally.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Switch to resource-managed function devm_led_classdev_register instead
of led_classdev_register and remove unneeded led_classdev_unregister.
To be compatible with this change, remove an unnecessary label by
replacing it with direct return statement.
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e;
@@
probefn(struct platform_device *pdev, ...) {
...
e =
- led_classdev_register
+ devm_led_classdev_register
(...);
...
?- led_classdev_unregister(...);
...
}
@remove depends on prb@
identifier platform.removefn;
@@
removefn(...) {
...
?- led_classdev_unregister(...);
...
}
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Use the GPIO flag definition instead of a numeric literal, so the casual
reader grepping for GPIOF_ will find the GPIO flags used.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Add helpers for calling brightness_set(_blocking) allowing to
simplify the code and make it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
In case of error, the function gpio_to_desc() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Improve the wording for the comment about the led status, and while at
it also use the standard formatting for multi-line comments.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
When a USB LED device is unplugged the remove call chain calls
led_classdev_unregister which tries to switch the LED off.
As the device has been removed already this results in a ENODEV
error message in dmesg.
Avoid this error message by ignoring ENODEV in calls from
led_classdev_unregister if the LED device is flagged as pluggable.
Therefore a new flag LED_HW_PLUGGABLE was introduced which should be set by
all LED drivers handling pluggable LED devices (mainly USB LED devices).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ran into this on UML:
drivers/built-in.o: In function `bcm6328_leds_probe':
drivers/leds/leds-bcm6328.c:340: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `bcm6358_leds_probe':
drivers/leds/leds-bcm6358.c:173: undefined reference to `devm_ioremap_resource'
collect2: error: ld returned 1 exit status
devm_ioremap_resource() is defined only when HAS_IOMEM is selected.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Complementing devm_led_classdev_register add a managed version of
led_trigger_register.
I omit a managed version of led_classdev_unregister as the equivalent
devm_led_classdev_unregister isn't used in the kernel as of today.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The busy status checking isn't needed while reading initial LED status.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
BCM6328 controller has a margin of 20ms per blink step, which means that
we can only set it to 20, 40, 60 ... 1260 ms (0x3f * 20ms).
However, when checking if delay_on == delay_off, we were not considering
the case when the user had set delay_on=20 and delay_off=21, since this
will cause the driver to fallback to software blinking.
This update fixes this issue and improves blink steps by rounding them
in a more sensible way. Now 30-49ms is rounded to 40 ms, and previous
behaviour implied 40-59ms being rounded to 40 ms.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
bcm6358_led_mode is now only called by bcm6358_led_set, so merge both
in one single function.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Instead of duplicating the unlock we can store the return value and use a
single unlock before returning that value, which simplifies the code.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This adds little endian support while keeping big endian support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
