Specify CPU supply using the "cpu-supply" property instead of
the invalid "arm-supply" property.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All Colibri iMX7 SKUs use either single-die NAND or eMMC, hence
NAND_CE1 is not used on the module and can be used as a GPIO by
carrier boards.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use pull-ups instead of pull-downs for the pins which are already
pulled-up externally.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Colibri pins PWM<A> and <D> are multiplexed on the module, make
sure the secondary SoC pin is not active.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Colibri default which enables USB Host power is not necessarily
tied to the OTG2 controller, some carrier board use the pin to
control USB power for both controllers. Hence name the pinctrl
group more generic.
Also move the regulator to the generic eval-v3 device tree since
the regulator is always on the carrier board. In the Colibri iMX7S
case the regulator is just not used. This allows to reuse the
regulator in a upcoming SKU Colibri iMX7D 1GB with eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string which describes the parallel
LCD.
Also, pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulators inside "simple-bus", so move
them out.
The motivation for doing this is to make it easier to adding new
regulators.
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.
So pass the "sii,43wvf1g" compatible string, which describes the parallel
LCD.
Also pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt
Signed-off-by: Marco Franchi <marcofrk@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared
to a st,m41t00 this RTC has also an oscillator fail bit which allows
to detect when the RTC lost track of time.
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This avoids the warning
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Esben Haabendal <eha@deif.com>
[RV: adapt commit log to the warning emitted in current mainline]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1021A can be reset via the dcfg regmap in the same way as the
arm64 layerscape SoCs, so add the corresponding DT node.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USB PHYs are supplied via MC13892 VUSB regulator rail,
so properly describe this in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
device_type = "pci" should be used for the SoC level PCI controller and
it is already present at imx6qdl.dtsi.
Remove it from the subnode in order to fix the following build
warnings with W=1:
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing ranges for PCI bridge (or not a bridge)
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_bridge): Node /soc/pcie@1ffc000/pci@0 missing bus-range for PCI bridge
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (unit_address_format): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
arch/arm/boot/dts/imx6q-zii-rdu2.dtb: Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6ul-14x14-evk.dtb: Warning (simple_bus_reg): Node /regulators/sd1_regulator missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the unneeded unit address for the i2cmux nodes in order to fix
the following build warnings with W=1:
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@3 has a unit name, but no reg property
While at it, rename the i2cmux nodes and subnodes to make it clearer to which
i2c controller the mux belongs to.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the unneeded unit address for the port nodes in order to fix
the following build warnings with W=1:
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a0000/tc358743@f/port@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@0 has a unit name, but no reg property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx6q-apalis-eval.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move disp0 node from soc node to root node.
disp0 node does not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (simple_bus_reg): Node /soc/disp0 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit name, but no reg property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/3p3v missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/usb-h1-vbus missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /regulators/usb-otg-vbus missing or empty reg/ranges property
Cc: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move disp0 node from soc node to root node.
disp0 node does not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx53-tx53-x03x.dtb: Warning (simple_bus_reg): Node /soc/disp0 missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx53-m53evk.dtb: Warning (unit_address_vs_reg): Node /soc/aips@60000000/i2c@63fc4000/stmpe610@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As described at Documentation/devicetree/bindings/mfd/mc13xxx.txt the
reg property is mandatory, so add the corresponding unit address in
order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled0 has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled1 has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The syscon node has an incorrect notation for its unit address and the
wdt node has an unneeded unit address.
Fix them so that the following build warnings with W=1 are gone:
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/syscon@b0010000/wdt@e has a unit name, but no reg property
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/touchscreen has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/syscon@b0010000 simple-bus unit address format error, expected "10000"
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/touchscreen simple-bus unit address format error, expected "12000"
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
SoM Carrier-Board.
This Carrier-Board has the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- On-board DMIC
- CAN bus header
- SPI header
- Camera Interfaces header
- 4xButtons, 2xLeds
- OnBoard RTC with Coin Backup battery socket
- RS232 Header + USB-Serial debug port
Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits
The board support is done with all on-board and header interfaces enabled.
7" LVDS Touchscreen is enabled by default along HDMI output.
Audio interface is supported with the "simple-card" bindings.
PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds support for the Variscite DART-MX6 SoM with :
- i.MX6 Quad or Dual Lite SoC
- 1Gb/2Gb LPDDR2
- 4-64 GB eMMC
- Camera Interface
- HDMI+CEC interface
- LVDS / DSI / Parallel RGB interfaces
- Ethernet RGMII interface
- On-SoM Wi-Fi/Bluetooth with WiLink wl1835 SDIO Module
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec with HP/Line-In interfaces + DMIC interface
- Digital Audio interface
- S/PDIF interface
Product website : http://www.variscite.com/products/system-on-module-som/cortex-a9/dart-mx6-cpu-freescale-imx6
Support is handled with a SoM-centric dtsi exporting the default interfaces
along the default pinmuxing to be enabled by the board dts file.
Only board-independent devices like WiFi, eMMC or PMIC are enabled in the dtsi.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing pinmux entry for OSC32K_32K_OUT on pad ENET_RXD0 used by the
Variscite DART-MX6 SoM.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1021AQDS support NAND flash on IFC chip-select 2.
So add NAND node in device tree for IFC controller.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Separate the old imx7d-pico into cpu (imx7d-pico.dtsi) and baseboard
(imx7d-pico-pi.dts) dts so the same cpu dtsi can be used in different
baseboards variants.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct unit address for interrupt-controller is 0x40003000, so
change it accordingly in order to fix the following build warning
with W=1:
arch/arm/boot/dts/vf500-colibri-eval-v3.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@40000000/interrupt-controller@40002000 simple-bus unit address format error, expected "40003000"
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct unit address for spba-bus is 0x2240000, so change it
accordingly in order to fix the following build warning with W=1:
arch/arm/boot/dts/imx6sx-sabreauto.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@2200000/spba-bus@2200000 simple-bus unit address format error, expected "2240000"
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move iio-hwmon node from soc node to root node.
iio-hwmon node does not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/vf500-colibri-eval-v3.dtb: Warning (simple_bus_reg): Node /soc/iio-hwmon missing or empty reg/ranges property
Based on a patch from Simon Horman for the renesas r8a7795 dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add unit address and reg for the anatop nodes in order to fix the
following build warnings with W=1:
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30000000/anatop@30360000/regulator-vdd1p0d missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move usbphynop1, usbphynop2, usbhypnop3, replicator and timer and nodes
from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/replicator missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/timer missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop1 missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop3 missing or empty reg/ranges property
arch/arm/boot/dts/imx7d-cl-som-imx7.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@30800000/usbphynop2 missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unneeded label and unit address in order to fix the following
build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux@34 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux@34 has a unit name, but no
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the reg properties for mipi nodes in order to fix the
following build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@1/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@1/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@2/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@2/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@3/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@3/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@4/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@4/endpoint@1 has a unit name, but no reg property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move tempmon, ldb and pmu nodes from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@2000000/tempmon missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /soc/aips-bus@2000000/ldb missing or empty reg/ranges property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (simple_bus_reg): Node /soc/pmu missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move pmu, usbphy0 and usbphy1 nodes from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx53-ard.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-0 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-1 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/pmu missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This node is for Low Power General Purpose Register which can
be used as Non-Volatile Storage.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse. To use the TMR_FIPER1
register to generate a 1 PPS event, the value
(10^9 nanoseconds) - TCLK_PERIOD should be programmed.
It should be 999999995 not 999999990 since TCLK_PERIOD
is 5.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the partitions definition for the SPI NOR to provide
backward compatibility with the documented[1] layout used with
Boundary Devices BSP.
1. https://boundarydevices.com/boot-flash-access-linux/
It exports to Linux:
mtd0: bootloader
mtd1: env
mtd2: splash
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam suggested using GPIO_ACTIVE_HIGH in the gpio specification
for the USB regulators. Change them to conform.
Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Cubox-i and Hummingboard variants for v1.5 SOMs, where the SOM has
eMMC fitted.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Cubox-i and Hummingboard variants for v1.5 SOMs, which have TI
Wi-Fi instead of Broadcom Wi-Fi. This variant does not include
SOM eMMC support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Node names are supposed to be generic, fix the RTC and codec node
names for both Hummingboard and Cubox-i.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make the regulators match the schematic - name the regulators after
one of their schematic supply names, and arrange them into their
heirarchy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
