When suspending the system with atmel_lcdfb enabled, I sometimes see
this:
atmel_lcdfb atmel_lcdfb.0: FIFO underflow 0x10
Which can be explained by the fact that we're not stopping the LCD
controller and its DMA engine when suspending, we're just gating the
clocks to them.
There's another potential issue which may be harder to trigger but
much more nasty: If we gate the clocks at _just_ the right moment,
e.g. when the DMA engine is doing a bus transaction, we may cause the
DMA engine to violate the system bus protocol and cause a lockup.
Avoid these issues by shutting down the LCD controller before entering
suspend (and restarting it when resuming). This prevents the underrun
from happening in the first place, and prevents whatever nastiness is
happening when the bus clock stops in the middle of a DMA transfer.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP1_IO_ADDRESS(), OMAP2_IO_ADDRESS() and IO_ADDRESS() returns cookies
for use with __raw_{read|write}* for accessing registers. Therefore,
these macros should return (void __iomem *) cookies, not integer values.
Doing this improves typechecking, and means we can find those places
where, eg, DMA controllers are incorrectly given virtual addresses to
DMA to, or physical addresses are thrown through a virtual to physical
address translation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: cleanup
Video mode selection became always possible in 2.6.23-rc1 after i386 setup
code rewrite in C.
Regardless, VIDEO_SELECT is stupid config option because it affects only
kernel setup code, not code which always stays in memory.
vga= always possible now which is good.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
If there are more then one graphics card handled by the tdfxfb driver the
name of the frame buffer overruns reserved size.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix memory detection on Voodoo3 cards with SDRAM memory.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Check if virtual resolution fits into memory.
Otherwise, Linux hangs during panning.
2. When selected use all available memory to
maximize yres_virtual to speed up panning
(previously also xres_virtual was increased).
3. Simplify memory restriction calculations.
Signed-off-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original am200epd driver was designed with bad assumptions. It
manipulated GPSR/GPLR registers directly. It relied on direct access to the
pxa LCDC registers which have since conflicted with commit
ce4fb7b892 . This patch moves it into mach-pxa
and overhauls it to use a fb obtained through fb notifiers. It now uses the
generic GPIO api.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These changes are used in order to support the use of the framebuffer
provided by the platform device driver rather than to directly allocate one.
Other changes are cleanup to error handling and order of release.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch converts the printk messages in metronomefb to dev_dbg/err type
messages.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes kernel BUG at lib/radix-tree.c:473.
Previously the handler was incidentally provided by tmpfs but this was
removed with:
commit 14fcc23fdc
Author: Hugh Dickins <hugh@veritas.com>
Date: Mon Jul 28 15:46:19 2008 -0700
tmpfs: fix kernel BUG in shmem_delete_inode
relying on this behaviour was incorrect in any case and the BUG also
appeared when the device node was on an ext3 filesystem.
v2: override a_ops at open() time rather than mmap() time to minimise
races per AKPM's concerns.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Johannes Weiner <hannes@saeurebad.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Kel Modderman <kel@otaku42.de>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [14fcc23fd is in 2.6.25.14 and 2.6.26.1]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug: does nor properply resume after suspend mem
Fix for PM_SUSPEND_MEM: Save and restore peripheral base and DMA registers
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Release cmap memory allocated in the probe function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are four operating modes Xen code may find itself running in:
- native
- hvm domain
- pv dom0
- pv domU
Clean up predicates for testing for these states to make them more consistent.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Xen-devel <xen-devel@lists.xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
The newly introduced "lcd_conn" field for connected LCD panel type will
cause the original code to generate the warnings of incorrect lccr*.
This is unnecessary since well encoded LCD_* flags will not generate
incorrect combinition of lccr* bits. Skip the check if "lcd_conn" is
specified.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Another fix of inconsistent shift of the LCD_BIAS_ACTIVE_* and
LCD_PCLK_EDGE_* is also included.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Alex Osborne <ato@meshy.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AOI position cannot be negative.
Signed-off-by: York Sun <yorksun@freescale.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Application can now have the virtual resoltuion and use FBIOPAN_DISPLAY
ioctl to pan.
Signed-off-by: York Sun <yorksun@freescale.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adjust and honor the vc_scrl_erase_char for 256 and 512 character fonts.
It fixes the issue with disappearing cursor during scrolling
(http://bugzilla.kernel.org/show_bug.cgi?id=11258). The issue was
reported and tracked by Peter Hanzel.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Peter Hanzel <hanzelpeter@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Specify how much physically continuous, DMA capable memory will be
allocated at driver initialization time. This allow to create framebuffer
device with larger virtual resolution. Combine with y-panning this can be
used to implement double buffering acceleration method.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Panning in the y-direction can be done by simply changing the DMA base
address. This code is already in place, but FBIOPAN_DISPLAY will
currently fail because ypanstep is 0.
Set ypanstep to 1 to indicate that we do support y-panning and also set
the necessary acceleration flags on AT91 (AVR32 already have them.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The legacy i2c model is going away soon, so switch to the new model.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the use of structure templates in i2c-matroxfb. In this case
it's more efficient to initialize the few fields we need individually.
This makes i2c-matroxfb.ko 16% smaller on my system.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I broke an error path with d03c21ec0b,
sorry about that.
The machine will crash if the i2c_attach_client() or maven_init_client()
calls fail, although nobody has yet reported this happening.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Petr Vandrovec <VANDROVE@vc.cvut.cz>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some chips appear to have the 2D engine hang during screen redraw,
typically in a sequence of copyarea operations. This appear to be
solved by adding a flush of the engine destination pixel cache
and waiting for the engine to be idle before issuing the accel
operation. The performance impact seems to be fairly small.
Here is a trace on an RV370 (PCI device ID 0x5b64), it records the
RBBM_STATUS register, then the source x/y, destination x/y, and
width/height used for the copy:
----------------------------------------
radeonfb_prim_copyarea: STATUS[00000140] src[210:70] dst[210:60] wh[a0:10]
radeonfb_prim_copyarea: STATUS[00000140] src[2b8:70] dst[2b8:60] wh[88:10]
radeonfb_prim_copyarea: STATUS[00000140] src[348:70] dst[348:60] wh[40:10]
radeonfb_prim_copyarea: STATUS[80020140] src[390:70] dst[390:60] wh[88:10]
radeonfb_prim_copyarea: STATUS[8002613f] src[40:80] dst[40:70] wh[28:10]
radeonfb_prim_copyarea: STATUS[80026139] src[a8:80] dst[a8:70] wh[38:10]
radeonfb_prim_copyarea: STATUS[80026133] src[e8:80] dst[e8:70] wh[80:10]
radeonfb_prim_copyarea: STATUS[8002612d] src[170:80] dst[170:70] wh[30:10]
radeonfb_prim_copyarea: STATUS[80026127] src[1a8:80] dst[1a8:70] wh[8:10]
radeonfb_prim_copyarea: STATUS[80026121] src[1b8:80] dst[1b8:70] wh[88:10]
radeonfb_prim_copyarea: STATUS[8002611b] src[248:80] dst[248:70] wh[68:10]
----------------------------------------
When things are going fine the copies complete before the next ROP is
even issued, but all of a sudden the 2D unit becomes active (bit 17 in
RBBM_STATUS) and the FIFO retry (bit 13) and FIFO pipeline busy (bit
14) are set as well. The FIFO begins to backup until it becomes full.
What happens next is the radeon_fifo_wait() times out, and we access
the chip illegally leading to a bus error which usually wedges the
box. None of this makes it to the console screen, of course :-)
radeon_fifo_wait() should be modified to reset the accelerator when
this timeout happens instead of programming the chip anyways.
----------------------------------------
radeonfb: FIFO Timeout !
ERROR(0): Cheetah error trap taken afsr[0010080005000000] afar[000007f900800e40] TL1(0)
ERROR(0): TPC[595114] TNPC[595118] O7[459788] TSTATE[11009601]
ERROR(0): TPC<radeonfb_copyarea+0xfc/0x248>
ERROR(0): M_SYND(0), E_SYND(0), Privileged
ERROR(0): Highest priority error (0000080000000000) "Bus error response from system bus"
ERROR(0): D-cache idx[0] tag[0000000000000000] utag[0000000000000000] stag[0000000000000000]
ERROR(0): D-cache data0[0000000000000000] data1[0000000000000000] data2[0000000000000000] data3[0000000000000000]
ERROR(0): I-cache idx[0] tag[0000000000000000] utag[0000000000000000] stag[0000000000000000] u[0000000000000000] l[00\
ERROR(0): I-cache INSN0[0000000000000000] INSN1[0000000000000000] INSN2[0000000000000000] INSN3[0000000000000000]
ERROR(0): I-cache INSN4[0000000000000000] INSN5[0000000000000000] INSN6[0000000000000000] INSN7[0000000000000000]
ERROR(0): E-cache idx[800e40] tag[000000000e049f4c]
ERROR(0): E-cache data0[fffff8127d300180] data1[00000000004b5384] data2[0000000000000000] data3[0000000000000000]
Ker:xnel panic - not syncing: Irrecoverable deferred error trap.
----------------------------------------
Another quirk is that these copyarea calls will not happen until the
first drivers/char/vt.c:redraw_screen() occurs. This will only happen
if you 1) VC switch or 2) run "consolechars" or 3) unblank the screen.
This seems to happen because until a redraw_screen() the screen scrolling
method used by fbcon is not finalized yet. I've seen this with other fb
drivers too.
So if all you do is boot straight into X you will never see this bug on
the relevant chips.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 2d04a4a72d, which made
it impossible to make the softcursor use the highlight colors.
Yes, the fourth bit should be "blinking", but since we cannot reasonably
blink in fbcon, highlighting it with a bright background is preferable.
Reported-by: Pavel Machek <pavel@suse.cz>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Antonino A. Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the LCD panel size for sh_mobile_lcdc boards. This allows us
to perform dpi and screen aspect ratio calculations in user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/video/aty/atyfb_base.c:2663: warning: 'aty_resume_chip' defined
but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Antonino A. Daplas <adaplas@pol.net>
Cc: Mark Asselstine <asselsm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_node_put is needed before discarding a value received from
of_find_node_by_type, eg in error handling code.
The semantic patch that makes the change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device_node *n;
struct device_node *n1;
struct device_node *n2;
statement S;
identifier f1,f2;
expression E1,E2;
constant C;
@@
n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f1(n,...)
when != E1 = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n2 = f2(n,...)
|
E2 = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Timur Tabi <timur@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of the i2c buses shows in the output of "i2cdetect -l", so
it's important to give informative names.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the 'clear' command is used on the frame buffer with a logo the upper
area is filled by few lines but not scrolled anymore.
Fix this by removing the protected area for the logo if any part of the
logo is cleared.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a new PCI-E radeon RV380 series card (PCI device ID 5b64) that
hangs in my sparc64 boxes when the init scripts set the font. The problem
goes away if I disable acceleration.
I haven't figured out that bug yet, but along the way I found some
corrections to make based upon some auditing.
1) The RB2D_DC_FLUSH_ALL value used by the kernel fb driver
and the XORG video driver differ. I've made the kernel
match what XORG is using.
2) In radeonfb_engine_reset() we have top-level code structure
that roughly looks like:
if (family is 300, 350, or V350)
do this;
else
do that;
...
if (family is NOT 300, OR
family is NOT 350, OR
family is NOT V350)
do another thing;
this last conditional makes no sense, is always true,
and obviously was likely meant to be "family is NOT
300, 350, or V350". So I've made the code match the
intent.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the missing MODULE_ALIAS() to the pwm_backlight driver.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the error paths in the pwm_backlight driver more informative in the
probe path, especially for the times that it finds an error.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 20e061fb75
Author: Ondrej Zajicek <santiago@crfreenet.org>
Date: Mon Apr 28 02:15:18 2008 -0700
fbdev: framebuffer_alloc() fixes
Correct the dev arg of framebuffer_alloc() in arkfb, s3fb and vt8623fb.
causes a null-pointer deref because "info->dev is NULL, info was just
kzallocated".
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Reported-by: "MadLoisae@gmx.net" <MadLoisae@gmx.net>
Tested-by: "MadLoisae@gmx.net" <MadLoisae@gmx.net>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
Add drivers/video/console/promcon_tbl.c to the list of ignored files.
This file is generated by conmakehash against drivers/video/console/prom.uni.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writes to the cmap fifo while the display is blanked caused cmap FIFO
timeout messages and a wrong colormap. To avoid this the driver now
maintains a colormap in memory and updates the colormap after the display
is unblanked.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems that we need to ensure that the lcd is powered up at start,
otherwise we do not see a display.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On HPPA there exists some older GSC graphics cards, which need special
graphic-card-BIOS patching to become supported. Since we don't have yet
implemented the patching, it's better to detect such cards in advance,
inform to the user that there are known problems and to not activate the
card.
Problematic GSC cards and BIOS versions are:
* Hyperdrive/Hyperbowl (A4071A) graphics card series:
* ID = 0x2BCB015A (Version 8.04/8)
* ID = 0x2BCB015A (Version 8.04/11)
* Thunder 1 VISUALIZE 48 card:
* ID = 0x2F23E5FC (Version 8.05/9)
* Thunder 2 VISUALIZE 48 XP card:
* ID = 0x2F8D570E (Version 8.05/12)
* Some Hyperion and ThunderHawk GSC cards
Further details are described here:
http://parisc-linux.org/faq/graphics-howto.html
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When registering an platform_lcd, use the name of the platform device
specified in case there are more than one platform_lcd backlights
registered.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The computed color value is never actually written to hardware
colormap register.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: Munakata Hisao <munakata.hisao@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This came in with the SH-Mobile LCDC changes in commit
cfb4f5d175, kill it off.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes the following needlessly global functions static:
- stifb_init_fb()
- stifb_init()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the needlessly global macfb_setup() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, linux/major.h defines a GRAPHDEV_MAJOR (29) that nobody uses,
and linux/fb.h defines the real FB_MAJOR (also 29), that only fbmem.c
needs. Drop GRAPHDEV_MAJOR from major.h, move FB_MAJOR definition from
fb.h to major.h, and fix fbmem.c to use major.h's definition.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a platform driver using the ATMEL PWM driver to control a
backlight which requires a PWM signal and optional GPIO signal for discrete
on/off signal. It has been tested on Favr-32 board from EarthLCD.
The driver is configurable by supplying a struct with the platform data. See
the include/linux/atmel-pwm-bl.h for details.
The board code for Favr-32 will be submitted to the AVR32 kernel list.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fourth bit of the background color is the blink property bit, not the
intensity bit, as for the foreground color. Therefore it shouldn't be
included in the background color.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the xtimings structure which only stored some values to be used
later (mostly once). Calculate and use these values in places they are
needed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop structure which is only set but never read. Drop variables which are
only set and never read. Convert one long switch into two shorter ones.
Add cpu_relax() in busy waiting loop.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is nothing to gain by converting value in kHz to fixed point MHz.
Just calculate everything in kHz.
A reorder of the loop allows reducing number of iterations (check if
frequency is not too high already).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains the following cleanups:
- make the needlessly global amifb_init() static
- rename cleanup_module() to amifb_exit(),
make it static __exit,
use module_exit(),
there's no need to #ifdef MODULE it
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simply enabling DAC blanking without turning off the CRT seems to be resulting
in characters remaining on the screen when the monitor blanks. This patch
turns off the CRT for all modes, and also powers down the DACs when vsync
and/or hsync are disabled.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We never sent the gamma stuff upstream, and don't really care about it.
However, lx_[gs]_et_gamma prototypes snuck into lxfb.h anyways; there are
no definitions for them. Drop the dead code.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the Freescale DIU driver to use page_alloc_exact() to allocate a
DMA buffer. This also eliminates the rheap-based memory allocator. We
can do this now because commit 6ccf61f9 allows us to allocate 8MB
physically- contiguous memory blocks.
[akpm@linux-foundation.org: fix printk warnings]
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a platform_lcd driver to allow boards with simple lcd power controls
to register themselves easily.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the lcd_device being checked to the check_fb entry of lcd_ops. This
ensures that any driver using this to check against it's own state can do
so, and also makes all the calls in lcd_ops more orthogonal in their
arguments.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide support for the ILI9320 display controller chip which is found in
many LCD displays. Included with this is support for an example LCD using
this chip, the VGG2432A4.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Andrew Morton, we have a problem when setting the 64bit
resources option. Alter the allocation routines to remove the need to use
the start and end fields, use the proper HEAD_PANEL/HEAD_CRT and update
the comments.
Note, we also fix the bug where we failed to check the size of the
CRT memory allocation.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the ability to register only one of the two possible main framebuffer
devices on the SM501 by passing platform data for only the framebuffer
that you are interested in having.
As a side note, we update the init sequence to commonise the code that is
executed twice, and fix a pair of missing frees that we didn't do on
framebuffer exit, such as freeing the fb's cmap.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add flags to allow the driver to invert the sense of both VBIASEN and FPEN
signals comming from the SM501.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid division by zero in atmel_lcdfb_check_var() function.
If pixclock is not specified while passing a var structure in
the check_var() funtion, a division by zero occurs (when
translating pixclock to KHz).
This patch adds a checking of this value and try to choose a
video mode in the modelist.
The mode found in the probe function in added to the modelist.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It updates skeletonfb to new platform driver API. The skeletonfb is
templates for creating new drivers.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The argument to iounmap() is void __iomem *. Fix the cast.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Properly propagate errors to the probe function.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert atyfb to use a PCI device ID table.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atari probe code relies on correct_chipset() failing if the device is not
a mach64 GX/CX. aty_chips[] array would be indexed with -1 in that case.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove dead code. This will slightly change the behaviour of the driver
on systems that support backlight control. Previously they would just
turn the backlight off using the backlight control but now the generic LCD
code will also turn off the LCD using the POWER_MANAGEMENT register.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The xoffset, yoffset and yres members of fb_var_screeninfo are __u32.
Make them unsigned in the code as well.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The width and height members of fb_var_screeninfo are __u32. The code
initializes them to -1 which seems wrong, and 0 seems like an equally good
default value.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the hgafb driver to use new platform driver API.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9689
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Kconfig help for the vfb driver says:
Do NOT enable it for normal systems! To protect the innocent, it
has to be enabled explicitly at boot time using the kernel option
`video=vfb:'.
This change lets the code match the description.
Support for vfb:disable is kept for backwards compatibility; vfb:off works
because it is tested at a higher level.
Note: any undefined option (e.g. vfb:enable) will also enable this driver.
The relevant code has been unchanged since before the migration to
git (2.6.12).
This patch fixes bugzilla #9310 and was the root cause behind
http://lkml.org/lkml/2008/5/31/220.
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Antonino A. Daplas <adaplas@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the SuperH Mobile LCDC frame buffer driver V2, adding support for
the LCDC block found in SuperH Mobile processors. The hardware supports
up to two LCD panels per LCDC block, and both RGB and SYS interfaces can
be used to hook up LCD panels/modules.
The device driver is a regular platform driver, so LCD configuration and
board specific hooks are passed to the driver using platform data. LCD
modules using SYS interface often require special configuration using the
SYS bus, and to solve this cleanly the driver provides SYS interface
operations to the board code.
Tested on sh7723 and sh7722 processors with a SYS16A QVGA panel and WVGA
panels using RGB16 and RGB18 interfaces.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Reviewed-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These checks and assignments are done by a higher layer so remove them
from the driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use constants and functions from the vga.h file. Also add module
description.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Small step toward unification of mode setting parameter. This is required
to fix the Bugzilla's bug 9847
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make more drivers use the "mode_option" parameter. This one is quite new
so drop the old "mode" parameter before someone starts using it seriously.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make logo_height variable local in the only function it is used.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Manage atmel_lcdfb FIFO underflow
Resetting the LCD and DMA allows to fix screen shifting after a FIFO
underflow. It follows reset sequence from errata "LCD Screen Shifting
After a Reset".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dx and dy are u32's, so the test should occur before the subtraction
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dx and dy are u32's, so the test should occur before the subtraction
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: Tim Schmielau <tim@physik3.uni-rostock.de>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dx and dy are u32's, so the test should occur before the subtraction
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pll->post_divider is unsigned, so the test fails
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current kernel builds warn about:
drivers/video/aty/radeon_base.c: In function 'radeonfb_pci_register':
drivers/video/aty/radeon_base.c:2334: warning: ignoring return value of 'sysfs_create_bin_file', declared with attribute warn_unused_result
drivers/video/aty/radeon_base.c:2336: warning: ignoring return value of 'sysfs_create_bin_file', declared with attribute warn_unused_result
Do minimal checking of these functions and issue a warning if either
fails. They don't seem to be critical..
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The semaphore ctrlr_sem is used as a mutex. Convert it to the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The semaphore ctrlr_sem is used as a mutex. Convert it to the mutex API.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mdacon incorrectly detects MDA hardware on systems without such graphics card.
One may load this module by chance, for example when doing some systematical
module-testing, and if there is no Monochrome Display Adapter attached ,
module init renders vc1-16 completely unusable.
I and others have run into this more than once. see [Bug 224522 - modprobe
mdacon freezes machine -> https://bugzilla.novell.com/show_bug.cgi?id=224522 ]
for example
Apparently proper MDA detection seems to be broken for a long time - seems to
be related to those #ifdef TEST_MDA_B statements added by Edward Betts.
this commit back in 2002 made things even worse :
http://git.kernel.org/?p=linux/kernel/git/tglx/history.git;a=commit;h=c72757b49c88914433244757fb4967fc63546685
It changed default vc allocation from 13-16 to 1-16 for no apparent reason
(!?) , and with that (and without X), mdacon grabs the vc you`re currently
sitting on and locks you out.
this is from Kconfig :
>config MDA_CONSOLE
> depends on !M68K && !PARISC && ISA
> tristate "MDA text console (dual-headed) (EXPERIMENTAL)"
> ---help---
> Say Y here if you have an old MDA or monochrome Hercules graphics
> adapter in your system acting as a second head ( = video card). You
> will then be able to use two monitors with your Linux system. Do not
> say Y here if your MDA card is the primary card in your system; the
> normal VGA driver will handle it.
As we can see mdacon is just meant as an additional driver for dual-head
setup, and since kernel 2.4.36 still defaults to vc13-16 , setting the default
back to that value again shouldn`t do any harm.
Hereby i'm reverting that change, setting default back to to vc13-16 again.
Besides the fact that mdacon may be rarely or never be used these days and
could perhaps put to trash anyway (pre-dinosaur hardware!), indeed this is not
a real solution, but at least it removes the unfortunate side-effect of
messing up the vc you`re working on.
Signed-off-by: Roland Kletzing <devzero@web.de>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Tim Schmielau <tim@physik3.uni-rostock.de>
Cc: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tridentfb driver should handle now all chipsets handled by the cyblafb
driver. Remove the message which claims that support will be removed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add imageblit acceleration for the Blade3D family of cores. The code is
based on code from the cyblafb driver.
It is a step toward assimilating back the cyblafb driver into the
tridentfb driver. The cyblafb driver handles a subfamily of the Trident
Blade3d cores.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes following problems:
- does not allow the m parameter to reach 0 as
it locks the graphics core (power cycle needed)
- for the newer chips (with new clock registers)
does not allow of n / m ratio below 4 as it gives
unstable image on the Blade3D core
- extend shift parameter (k) range to 2 for the newer
chips to cope with the n /m >= 4 limit at low resolution
(bandwidth) modes
- prefer modes with higher n / m ratio (higher k values)
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Trident cards uses only 20-bit address of screen start in double
words. This allows addressing for only 4MB of video memory so check this.
Also remove some redundant checks and assignments.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix depth setting for 8 bpp mode. The nice 224 color logo is not
displayed in 8 bpp depth without this fix.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes two problems when acceleration is enabled:
- console switch from the Xorg locks up the computer
because the Xorg code locks some registers and disables
the mmio mode, so reenable these in the
tridentfb_set_par() and enable_mmio()
- blacklist the Image975 chipset from setting PCI burst
mode. This helps with random lock ups of the
framebuffer on this chip. The same fix is probably
needed for the Xorg as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains general source code improvments:
- more simple functions are inline
- removes some meaningless output and the VERSION
string as it is no use
- eng_par is moved into the tridentfb_par
- removed small section of code for CyberBladeXPAi1
which is maybe right for only one resolution
and refresh rate and is probably redundant now
- other minor improvements
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces deprecated constant FB_ACCELF_TEXT with
FBINFO_HWACCEL_DISABLED and adds constants for Trident families of
accelerators.
The FBINFO_HWACCEL_DISABLED is correctly used so noaccel parameter works
now.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes few issues related to timings and pixclock generation:
- disallow the pixclocks with numerator lower than
double denominator. This fixes display instability
for some modes.
- choose the pixelclock with the highest
numerator and denominator values. This improve
image quality and fixes display instability
for some modes.
- make interlaced modes work.
- set synchronization pulses polarization
correctly.
- horizontal synchronization timing are now
the same as generated by X.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes two problems when acceleration is enabled:
- bit for bitblt direction is corrected
so scrolling down works as expected on 3DImage chips
- initialization of acceleration is done later
this helps with initial console malfuntion (on Blade3D
chips) well documented here:
http://marc.info/?l=linux-fbdev-users&m=111386953124478&w=2
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch brings various acceleration improvements:
- set copyarea/fillrect for non-accelerated framebuffer (fix)
- remove 15 bpp depth handling to simplify code as it hardly
works (15 bpp handling was obviously missing in some switches)
- add fb_sync call and move waiting before accelerated function
to make acceleration more asynchronous to cpu (few % of speed
improvement)
- add cpu_relax() call in waiting loops
- make longer register names and name more registers
- move registers' definition to header
- general code improvements (shortening, simplifying)
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds acceleration for TGUI 9440 and 96xx chips. These chips
requires line length to be power of 2, so this is also changed.
It also moves the troubling enable_mmio() function to its final
destination.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TGUI 9440 requires doubling clock for 16bpp (hi-color) modes.
The patch also moves back enable_mmio() call to the right position.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not overwrite bits which contain memory type settings. It removes
noise pixels ("snow") on Blade3D and 3DImage chips.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do some additional checks (like pixelclock versus ramdac speed) to
eliminate modes which do not work.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initialize the pseudo_palette pointer properly. This fixes crash when
16bpp or 32bpp mode is selected.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for TGUI 9440 chip.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improved values for some registers after Xorg Trident driver. The main
problem was that values set by BIOS have been ignored.
This patch completely remove random pixels ("snow") on the TGUI 9680 and
9440 (not supported yet by the driver). It does not help with the "snow"
on 3DImage and Blade3D cards.
There is also small improvement in timing calculations (hblank start and
vblank start)
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add missing release of allocated fb_info structure and move enable_mmio() to
fix error path.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Xorg code shows that Trident models 9660, 9680 and 9682 require a
different clock setting method. Add the second clock setting method for older
models.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the mmio outb function instead of direct one. The mmio registers are
already mapped (in the probe function).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix broken timings calculations. This patch helps with following
problems:
- no left part of screen visible (up to half of the screen)
- monitor's frequencies are not the ones intended for selected modes
- if mode with resoultion y > 1024 is selected at least once then
all modes with y < 1024 are "out of sync" (no display)
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make use of functions and constants from the vga.h header to compact the code
and make it more readable.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves acceleration hooks into the tridentfb_par structure and
removes global hooks.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts the is_blade() and is_xp() macros into local functions.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves flat panel indicator into tridentfb_par structure and removes
related global variables and macros.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the chip_id into tridentfb_par structure and removes global
chip_id related constants.
It also bumps version of the driver to 0.7.9
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves pseudo palette int tridentfb_par structure and removes global
default_var.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts fb_info structure from global variable to allocatable one.
The global default_par is moved into function variable.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces macros with static functions and puts tridentfb_par
pointer as the first argument of these functions. These is a step toward
multihead support.
Additionally, bogus TRIDENT_MMIO define is removed as the driver supports
graphics cards only through the mmio mode.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Basic FB driver for the carmine chip. The driver registers two FB devices for
the two possible screens. The DRAM settings can be be switched via Kconfig
(between eval board and custom).
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
