Before doing any other verifications, the add_remote_oob_data function
should first check that the given address is valid. This patch adds such
a missing check to the beginning of the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When BR/EDR is supported by a controller, then it is required to enable
Secure Simple Pairing first before enabling the Secure Connections
feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a powered on dual-mode controller has been configured to operate
as LE only with secure connections, then the BR/EDR side of things can
not be switched back on. Do reconfigure the controller it first needs
to be powered down.
The secure connections feature is implemented in the BR/EDR controller
while for LE it is implemented in the host. So explicitly forbid such
a transaction to avoid inconsistent states.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BR/EDR Secure Connections feature should only be enabled when the
Secure Simple Pairing mode has been enabled first. However since secure
connections is feature that is valid for BR/EDR and LE, this needs
special handling.
When enabling secure connections on a LE only configured controller,
thent the BR/EDR side should not be enabled in the controller. This
patches makes the BR/EDR Secure Connections feature depending on
enabling Secure Simple Pairing mode first.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Start Discovery was reporting 0 RSSI for invalid RSSI only for
BR/EDR devices. LE devices were reported with RSSI 127.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.19+
Remove the function hci_conn_change_link_key() that is not used anywhere.
This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the SMP channels have been already registered, then print out a
clear WARN_ON message that something went wrong. Also unregister the
existing channels in this case before trying to register new ones.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The comparing of chan->src should always be done against the local
identity address, represented by hcon->src and hcon->src_type. This
patch modifies l2cap_global_fixed_chan() to take the full hci_conn so
that we can easily compare against hcon->src and hcon->src_type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current bdaddr_type() usage in l2cap_core.c is a bit funny in that
it's always passed a hci_conn + a hci_conn member. Because of this only
the hci_conn is really needed. Since the second parameter is always
either hcon->src_type or hcon->dst type this patch adds two helper
functions for each purpose: bdaddr_src_type() and bdaddr_dst_type().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the controller gets powered on via the management interface, then
register the supported SMP channels. There is no point in registering
these channels earlier since it is not know what identity address the
controller is going to operate with.
When powering down a controller unregister all SMP channels. This is
required since a powered down controller is allowed to change its
identity address.
In addition the SMP channels are only available when the controller
is powered via the management interface. When using legacy ioctl, then
Bluetooth Low Energy is not supported and registering kernel side SMP
integration may actually cause confusion.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When LE features are not supported, then do not bother registering any
kind of SMP channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The source address and source address type of the LE SMP channel can
either be the public address of the controller or the static random
address configured by the host.
Right now the public address is used for the LE SMP channel and
obviously that is not correct if the controller operates with the
configured static random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For dual-mode controllers it is possible to disable BR/EDR and operate
as LE single mode controllers with a static random address. If that is
the case, then refuse switching BR/EDR back on after the controller has
been powered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The devices address types are BR/EDR Public, LE Public and LE Random and
any of these three is valid for L2CAP connections. So show the correct
type in the debugfs list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Removing PSM setting debugfs interface as the IPSP has a well
defined PSM value that should be used.
The patch introduces enable flag that can be used to toggle
6lowpan on/off.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the Bluetooth core specification valid identity addresses
are either Public Device Addresses or Static Random Addresses. IRKs
received with any other type of address should be discarded since we
cannot assume to know the permanent identity of the peer device.
This patch fixes a missing check for the Identity Address when receiving
the Identity Address Information SMP PDU.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.17+
Variable 'controller' is assigned a value that is never used.
Identified by cppcheck tool.
Signed-off-by: Gowtham Anandha Babu <gowtham.ab@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The duration variable for the selftests is unsigned long long and with
that use %llu instead of %lld when printing the results.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This moves the execution of Delete Stored Link Key command to the
hci_init4_req phase. No actual code has been changed. The command
is just executed at a later stage of the initialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI Delete Stored Link Key command completes, then update the
value of current stored keys in hci_dev structure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The information about max stored link keys and current stored link keys
should be read at controller initialization. So issue HCI Read Stored
Link Key command with BDADDR_ANY and read_all flag set to 0x01 to
retrieve this information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI Read Stored Link Keys command completes it gives useful
information of the current stored keys and maximum keys a controller
can actually store. So process this event and store these information
in hci_dev structure.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The send_monitor_event function is essentially the same as the newly
introduced queue_monitor_skb. So instead of having duplicated code,
replace send_monitor_event with queue_monitor_skb.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_send_to_monitor function contains generic code for queueing the
packet into the receive queue of every monitor client. To avoid code
duplication, create a generic queue_monitor_skb function to interate
over all monitor sockets.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Within the monitor functionality, the global atomic variable called
monitor_promisc ensures that no memory allocation happend when there
is actually no client listening. This means it is safe to just create
a copy of the skb since it is guaranteed that at least one client
exists. No extra checks needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds an extra check for ensuring that the size of sockaddr_sco
does not grow larger than sockaddr.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds an extra check for ensuring that the size of sockaddr_rc
does not grow larger than sockaddr.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds an extra check for ensuring that the size of sockaddr_l2
does not grow larger than sockaddr.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds an extra check for ensuring that the size of sockaddr_hci
does not grow larger than sockaddr.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When hci_req_run() calls its provided complete function and one of the
HCI commands in the sequence fails, then provide the opcode of failing
command. In case of success HCI_OP_NOP is provided since all commands
completed.
This patch fixes the prototype of hci_req_complete_t and all its users.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_QUIRK_FIXUP_INQUIRY_MODE option allows to force Inquiry Result
with RSSI setting on controllers that do not indicate support for it,
but where it is known to be fully functional.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are some old Bluetooth modules from Silicon Wave and Broadcom
which support Inquiry Result with RSSI, but do not advertise it. The
core has quirks in the code to enable that inquiry mode. However as
it stands right now, that code is not even executed since entering
the function to determine which inquiry mode requires that the device
has the feature bit for Inquiry Result with RSSI set in the first
place. So this makes this dead code that hasn't work for a long
time.
In conclusion, just remove these extra quirks and simplify the setup
of the inquiry mode to be inline and with that a lot easier to read
and understand.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Bluetooth controllers requires an unconfigured state (for
example when the BD_ADDR is missing), then it is important to try
to register the SMP channels when the controller transitions to the
configured state.
This also fixes an issue with the debugfs entires that are not present
for controllers that start out as unconfigured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
One of the LE Secure Connections security credentials was still using
the BT_DBG instead of SMP_DBG.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The sc_only_mode debugfs entry is used to read the current state of the
Secure Connections Only mode. Before Bluetooth 4.2 this mode was only
for BR/EDR controllers and with that tight to the support Secure Simple
Pairing. Since Secure Connections is now available for BR/EDR and LE
this debugfs entry is no longer correctly place.
Move it to the common section and enable it when either BR/EDR Secure
Connections feature is supported or when the controller has LE support.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The force_sc_support debugfs option was introduced to easily work with
pre-production Bluetooth 4.1 silicon. This option is no longer needed
since controllers supporting BR/EDR Secure Connections feature are now
available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The force_lesc_support debugfs option never really worked. It has a race
condition between creating the debugfs entry and registering the L2CAP
fixed channel for BR/EDR SMP support.
Also this has been replaced with a working force_bredr_smp debugfs
switch that developers can use now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Testing cross-transport pairing that starts on BR/EDR is only valid when
using a controller with BR/EDR Secure Connections. Devices will indicate
this by providing BR/EDR SMP fixed channel over L2CAP. To allow testing
of this feature on Bluetooth 4.0 controller or controllers without the
BR/EDR Secure Connections features, introduce a force_bredr_smp debugfs
option that allows faking the required AES connection.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg say:
====================
pull request: bluetooth-next 2014-12-31
Here's the first batch of bluetooth patches for 3.20.
- Cleanups & fixes to ieee802154 drivers
- Fix synchronization of mgmt commands with respective HCI commands
- Add self-tests for LE pairing crypto functionality
- Remove 'BlueFritz!' specific handling from core using a new quirk flag
- Public address configuration support for ath3012
- Refactor debugfs support into a dedicated file
- Initial support for LE Data Length Extension feature from Bluetooth 4.2
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After successful completion of the ECDH test cases, print the time it
took to run them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After successful completion of the SMP test cases, print the time it
took to run them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds SMP self-tests for the Secure Connections crypto
functions. The sample data has been taken from the core specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds self-tests for legacy SMP crypto functions. The sample
data has been taken from the core specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the initial skeleton and kernel config option for SMP
self-tests.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the test cases for ECDH cryptographic functionality
used by Bluetooth Low Energy Secure Connections feature.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This add support for the Bluetooth self testing framework that allows
running certain test cases of sample data to ensure correctness of its
basic functionality.
With this patch only the basic framework will be added. It contains
the build magic that allows running this at module loading time or
at late_initcall stage when built into the kernel image.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These SMP crypto functions should have all their input parameters
declared as const. This patch fixes the parameters that were missing the
const declaration.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The AVM BlueFritz! USB controllers had a special handling in the
Bluetooth core when it comes to reading the supported commands.
Both drivers now set the HCI_QUIRK_BROKEN_LOCAL_COMMANDS and with
that it is no longer needed to look for vendor specific details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When connectable mode is enabled (page scan on) through some non-mgmt
method the HCI_CONNECTABLE flag will not be set. For backwards
compatibility with user space versions not using mgmt we should not
require HCI_CONNECTABLE to be set if HCI_MGMT is not set.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.17+
When controllers set the HCI_QUIRK_INVALID_BDADDR flag, it is required
by userspace to program a valid public Bluetooth device address into
the controller before it can be used.
After successful address configuration, the internal state changes and
the controller runs the complete initialization procedure. However one
small difference is that this is no longer the HCI_SETUP stage. The
HCI_SETUP stage is only valid during initial controller setup. In this
case the stack runs the initialization as part of the HCI_CONFIG stage.
The controller version information, default name and supported commands
are only stored during HCI_SETUP. While these information are static,
they are not read initially when HCI_QUIRK_INVALID_BDADDR is set. So
when running in HCI_CONFIG state, these information need to be updated
as well.
This especially impacts Bluetooth 4.1 and later controllers using
extended feature pages and second event mask page.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org # 3.17+
