commit: "carl9170: revamp carl9170_tx_prepare"
introduced a peculiar bug that would only show
up if the the module parameter noht is set to 1.
Then all outbound voice, video and background
frames would each invoke a (bogus) RTS/CTS
handshake.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
while removing beaconing mode interface, SWBA interrupt
was never disabled when there are no other beaconing interfaces.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With some upcoming changes we'd like to use
the interface types for P2P capability tests.
Enable them now so that when we add those
tests in wpa_supplicant, nothing will break.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver uses a shared pm_qos_request_list structure for all
devices. This causes the following warning if more than one device is
present in the system:
WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0()
pm_qos_add_request() called for already added request
Modules linked in:
Call Trace:
[<802b1cdc>] dump_stack+0x8/0x34
[<8007dd90>] warn_slowpath_common+0x78/0xa4
[<8007de44>] warn_slowpath_fmt+0x2c/0x38
[<801b0828>] ath9k_init_device+0x5e8/0x6b0
[<801bc508>] ath_pci_probe+0x2dc/0x39c
[<80176254>] pci_device_probe+0x64/0xa4
[<8019471c>] driver_probe_device+0xbc/0x188
[<80194854>] __driver_attach+0x6c/0xa4
[<80193e20>] bus_for_each_dev+0x60/0xb0
[<80193580>] bus_add_driver+0xcc/0x268
[<80194c08>] driver_register+0xe0/0x198
[<801764e0>] __pci_register_driver+0x50/0xe0
[<80365f48>] ath9k_init+0x3c/0x6c
[<8006050c>] do_one_initcall+0xfc/0x1d8
[<80355340>] kernel_init+0xd4/0x174
[<800639a4>] kernel_thread_helper+0x10/0x18
---[ end trace 5345fc6f870564a6 ]---
This patch fixes that warning by using a separate pm_qos_request_list
sructure for each device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
card->priv must not be accessed after lbs_remove_card() was called
as lbs_remove_card() frees card->priv via free_netdev().
For libertas_sdio this is a regression introduced by 23b149c189.
The correct fix to the issue described there is simply to remove the
assignment. This flag is set at the appropriate time inside
lbs_remove_card anyway.
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"priv" is stored at the end of the wiphy structure, which is freed
during the call to lbs_cfg_free(). It must not be touched afterwards.
Remove the unnecessary NULL assignment causing this memory corruption.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix unbalanced call to sdio_release_host() on the error path.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting tid information in the TX header is required only for QoS
frames. Not handling this case causes severe data loss with some APs.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9287 based PCI & USB devices are differed in eeprom start offset.
So set proper the offset for HTC devices to read nvram correctly.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Treat new PIDs (0xA704, 0x1200) as AR7010 devices.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added new VID/PIDs into supported devices list
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update pm_qos before removing it in deinit_device to prevent this
warning:
pm_qos_update_request() called for unknown object.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
usb_wait_anchor_empty_timeout's @timeout
wants milliseconds and not jiffies.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to use build-in debugging macro, pci_dev in priv need to be
assigned first.
This fix iwl3945 driver oopsed at boot with 2.6.37-rc1
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The allocated externel radio banks have to be freed in
case of ath9k_hw_rf_alloc_ext_banks failure.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the endpoint descriptors (EP3 & EP4) were changed from Interrupt
to Bulk type by firmware, the urb submission done on Bulk pipes.
And the recent commit "check the endpoint type against the pipe type"
added aditional error checking against pipe types under CONFIG_USB_DEBUG.
So bmAttribute has to be updated for both EP3 & EP4 before submitting
urbs on that pipe. This patch resolves the following failure.
[ 2215.710936] usb 1-1: usb_probe_device
[ 2215.710945] usb 1-1: configuration #1 chosen from 1 choice
[ 2215.711152] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 2215.711252] ath9k_hif_usb 1-1:1.0: usb_probe_interface
[ 2215.711255] ath9k_hif_usb 1-1:1.0: usb_probe_interface - got id
[ 2215.712780] usb 1-1: BOGUS urb xfer, pipe 3 != type 1
[ 2215.713782] usb 1-1: ath9k_htc: Unable to allocate URBs
[ 2215.713801] ath9k_hif_usb: probe of 1-1:1.0 failed with error -22
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for USB dongle with device ID 3346 from IMC Networks.
Signed-off-by: Haitao Zhang <minipanda@linuxrobot.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 22 of AR_WA should be set to fix the situation where chip reset
is asynchronous to clock of analog shift registers, such that when
reset is released, it could mess up the values of analog shift registers
and cause some hw issue on AR9280.
This bit is write only, but the driver does a read-modify-write
on AR_WA without setting bit 22 in ar9002_hw_configpcipowersave()
during radio disable. This causes surprise removal of hw. It can
never recover from this state and the hw will become usable only
after a power on/off cycle, and sometimes only during a cold reboot.
This issue can be triggered by doing frequent roaming with the
simple/test-roam script available from the wifi-test project [1]
when roaming between APs quickly. When roaming there is a is a high
possibility that the device being put into idle (radio disable) state
by mac80211 during AUTH->ASSOC. A device hardware reset would fail
and the kernel would output:
[40251.363799] ath: AWAKE -> FULL-SLEEP
[40251.363815] ieee80211 phy17: device no longer idle - working
[40251.363817] ath: Marking phy17 as not-idle
[40251.363819] ath: FULL-SLEEP -> AWAKE
[40251.415978] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3)
[40251.419896] ath: ah->misc_mode 0x4
[40251.428138] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[40251.532247] ath: timeout (100000 us) on reg 0x9860: 0xffffffff & 0x00000001 != 0x00000000
[40251.532250] ath: Unable to reset channel (2462 MHz), reset status -5
[40251.532422] ath: Set channel: 5745 MHz
[40251.540639] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.548826] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.557023] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.565211] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.573415] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.581603] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.581606] ath: Failed to stop TX DMA. Resetting hardware!
[40251.592679] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff
[40251.703330] ath: timeout (100000 us) on reg 0x7000: 0xffffffff & 0x00000003 != 0x00000000
[40251.703333] ath: RTC stuck in MAC reset
[40251.703334] ath: Chip reset failed
[40251.703335] ath: Unable to reset hardware; reset status -22
This is currently only reproducible with some HB92 (Half Mini-PCIE)
cards but the fix applies to all AR9280 cards. This patch fixes this
issue by setting bit 22 during radio disable.
This patch has fixes for all kernels that has ath9k.
[1] http://wireless.kernel.org/en/developers/Testing/wifi-test
Cc: kyungwan.nam@atheros.com
Cc: amod.bodas@atheros.com
Cc: david.quan@atheros.com
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are currently no provisions in place to ensure that the scanning
task has been stopped when the interface is stopped or removed.
This can result in a WARNING at net/wireless/core.c:643 and other badness
when you remove the module while a scan is happening.
Terminate the scanning task during interface stop.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_ps_wakeup() clears the cycle counters after waking up the
hardware using ath9k_hw_setpower, however if power save is disabled,
then the counters will contain useful data, which then gets discarded.
Fix this by checking the old power mode before discarding any data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch includes the following updates:
* add D-Link DWA-130 Rev D
* Netgear has three WNDA3100 versions.
the original WNDA3100 is now called WNDA3100v1.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Throughput was severely affected in Intel Pinetrail platforms
because of a DMA problem in C3 state. This patch fixes this
issue.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW opmode is blindly set to monitor type on monitor mode
change notification. This overrides the opmode when one of the
interfaces is still running as non-monitor iftype. So the monitoring
information needs to be maintained seperately.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bug seems to be due to commit 27ae60f8f7 ("ipw2x00: replace
"ieee80211" with "libipw" where appropriate"), where Pavel did this:
- libipw_proc = proc_mkdir(DRV_NAME, init_net.proc_net);
+ libipw_proc = proc_mkdir("ieee80211", init_net.proc_net);
but then the cleanup was kept as
remove_proc_entry(DRV_NAME, init_net.proc_net);
in both places (both in the failure case and in the unload case). The
error string is also total crap, and says
"Unable to create " DRV_NAME " proc directory\n");
Even though it doesn't actually create a proc directory named DRV_NAME at all.
So that patch looks like total and utter crap to me. The commit message says
"Keep /proc/net/ieee80211 under the original name to avoid breaking user
interface."
but the thing is, it really didn't fix anything but that one create
thing. It needs to fix all the other cases too.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the SD8686, we cannot rely on the scratch register to read the firmware
load status, because the same register is used for storing RX packet length.
Broaden the check to account for this.
The module can now be unloaded/reloaded successfully.
Based on the implementation from libertas_tf.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The index variable to access the rate flags should be obtained from the
inner loop counter which corresponds to the rate table structure.This
fixes the invalid rate selection i.e when the supported basic rate is
invalid on a particular band and also the following warning message.
Thanks to Raj for finding this out.
Call Trace:
[<ffffffff8104ee4a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104ee95>] warn_slowpath_null+0x15/0x20
[<ffffffffa0583c45>] ath_get_rate+0x595/0x5b0 [ath9k]
[<ffffffff811a0636>] ? cpumask_next_and+0x36/0x50
[<ffffffffa0405186>] rate_control_get_rate+0x86/0x160 [mac80211]
[<ffffffffa040dfac>] invoke_tx_handlers+0x81c/0x12d0 [mac80211]
[<ffffffffa040eae9>] ieee80211_tx+0x89/0x2b0 [mac80211]
[<ffffffff812891bc>] ? pskb_expand_head+0x1cc/0x1f0
[<ffffffffa040edc5>] ieee80211_xmit+0xb5/0x1c0 [mac80211]
[<ffffffffa041026f>] ieee80211_tx_skb+0x4f/0x60 [mac80211]
[<ffffffffa03fe016>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]
[<ffffffffa03f91d7>] ieee80211_offchannel_stop_station+0x107/0x150
[mac80211]
[<ffffffff812891bc>] ? pskb_expand_head+0x1cc/0x1f0
[<ffffffffa040edc5>] ieee80211_xmit+0xb5/0x1c0 [mac80211]
[<ffffffffa041026f>] ieee80211_tx_skb+0x4f/0x60 [mac80211]
[<ffffffffa03fe016>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]
[<ffffffffa03f91d7>] ieee80211_offchannel_stop_station+0x107/0x150
[mac80211]
[<ffffffffa03f8896>] ieee80211_scan_work+0x146/0x600 [mac80211]
[<ffffffff8133a375>] ? schedule+0x2f5/0x8e0
[<ffffffffa03f8750>] ? ieee80211_scan_work+0x0/0x600 [mac80211]
[<ffffffff81064fcf>] process_one_work+0x10f/0x380
[<ffffffff81066bc2>] worker_thread+0x162/0x340
[<ffffffff81066a60>] ? worker_thread+0x0/0x340
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If ath5k_hw_attach fails it will free sc->ah (local variable ah) before
returning. However, when it reports failure the caller (ath5k_pci_probe)
will also free sc->ah. Let the caller handle the deallocation, it does
so on further errors as well.
Signed-off-by: Jones Desougi <jones.desougi@27m.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Netgear WNDA3200 device uses ar7010 firmware but it is failed to set
correct firmware offset on firmware download which causes device initialization
failure.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completing aggregate frames can lead to new buffers being pushed into
the tid queues due to software retransmission.
When the tx queues are being drained, all pending aggregates must be
completed before the tid queues get drained, otherwise buffers might be
leaked.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apart from locking the start and stop PCU we need
to ensure we also content starting and stopping the PCU
between hardware resets.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The real way to lock RX is to contend on the PCU
and reset, this will be fixed in the next patch but for
now just do the renames so that the next patch which changes
the locking order is crystal clear.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was some locking for starting some parts of
RX but not for starting the PCU. Include this otherwise
we can content against stopping the PCU.
This can potentially lead to races against different
buffers on the PCU which can lead to to the DMA RX
engine writing to buffers which are already freed.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k locks for starting RX but not for stopping RX. We could
potentially run into a situation where tried to stop RX
but immediately started RX. This allows for races on the
the RX engine deciding what buffer we last left off on
and could potentially cause ath9k to DMA into already
free'd memory or in the worst case at a later time to
already given memory to other drivers.
Fix this by locking stopping RX.
This is part of a series that will help resolve the bug:
https://bugzilla.kernel.org/show_bug.cgi?id=14624
For more details about this issue refer to:
http://marc.info/?l=linux-wireless&m=128629803703756&w=2
Cc: stable@kernel.org
Cc: Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Timing issues in microcode for some devices can cause a compressed BA to
be sent to the driver prior to returning any a-MPDU notification.
Traces show RTS-CTS is exchanged and then the timer fires which causes an
empty BA to be sent which acknowledges nothing. This results in a noisy
printk. Only print the message if the bitmap is non-zero.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since aggregation is usually triggered by tx completion, a hardware
reset (because of beacon stuck, tx hang or baseband hang) can
significantly delay the transmission of the next AMPDU (until the next
tx completion event).
Fix this by rescheduling aggregation after such a reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1251 move accidently renamed wl1251_sdio and wl1251_spi
modules to just sdio and spi. Restore proper module names.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k aggregation code was already checking the rate control probe flag
to prevent starting an aggregate frame with a sampling rate. What was missing
was closing an aggregate before adding a probing frame to it.
Without that, rate control cannot have precise control over probing, which
delays using faster rates when the channel conditions improve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If ah->curchan is uninitialized, the channel index is bogus, which leads
to invalid memory access when the cycle counters are updated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are not handling all divide by zero cases in paprd.
Add additional checks for divide by zero cases in papard.
This patch has fixes intended for kernel 2.6.36.
Cc: stable@kernel.org
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This updates the initvals for the AR9003 2.2 chipsets. The initvals
are the initial register values we use for our registers upon hardware
reset. This synchs up the initvals to match what our latest recommendation
from our systems engineering team.
The description of changes in this update:
Improves ability to support very strong Rx conditions.
Enhances DFS support for AP-mode.
Improves performance of Tx carrier leak calibration.
Adds support for Japan channel 14 Tx filtering requirements.
Improves Tx power accuracy.
Impact:
Update required to address degraded throughput at very short range.
Update required for AP-mode DFS certification.
Update required to comply to IEEE Tx carrier leak specification.
May not meet expected +/- 2 dB Tx power accuracy without update.
The most important fix here would be the TX carrier leakage required
to comply with IEEE 802.11 specifications. The group of changes have
been tested all together in one release.
References:
Osprey 2.2 header file ver #33
Checksums:
$ ./initvals -f ar9003-2p2
0x000000004a488fc7 ar9300_2p2_radio_postamble
0x0000000046cb1300 ar9300Modes_lowest_ob_db_tx_gain_table_2p2
0x00000000e912711f ar9300Modes_fast_clock_2p2
0x0000000037ac0ee8 ar9300_2p2_radio_core
0x00000000047a7700 ar9300Common_rx_gain_table_merlin_2p2
0x0000000003f783bb ar9300_2p2_mac_postamble
0x00000000301fc841 ar9300_2p2_soc_postamble
0x000000005ec8075f ar9200_merlin_2p2_radio_core
0x0000000083372ffa ar9300_2p2_baseband_postamble
0x00000000c4f59974 ar9300_2p2_baseband_core
0x00000000e20d2e72 ar9300Modes_high_power_tx_gain_table_2p2
0x000000007fd55c70 ar9300Modes_high_ob_db_tx_gain_table_2p2
0x0000000029495000 ar9300Common_rx_gain_table_2p2
0x0000000042cb1300 ar9300Modes_low_ob_db_tx_gain_table_2p2
0x00000000c4739cd6 ar9300_2p2_mac_core
0x000000003521a300 ar9300Common_wo_xlna_rx_gain_table_2p2
0x00000000a15ccf1b ar9300_2p2_soc_preamble
0x0000000029734396 ar9300PciePhy_pll_on_clkreq_disable_L1_2p2
0x000000002d834396 ar9300PciePhy_clkreq_enable_L1_2p2
0x0000000029834396 ar9300PciePhy_clkreq_disable_L1_2p2
$ ./initvals -f ar9003-2p2 | sha1sum
0ceddb5cf66737610fb51f04cf3e9ff71870c7b4 -
Cc: stable@kernel.org
Cc: Yixiang Li <yixiang.li@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch continues where the previous commit:
"carl9170: fix async command buffer leak"
left off.
Similar to carl9170_reboot/carl9170_powersave, the
carl9170_async_regwrite* macros would leak the
temporary command buffer, if __carl9170_exec_cmd
fails to upload the command to the device.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If __carl9170_exec_cmd fails to upload an asynchronous
command to the device, the functions: carl9170_reboot
and carl9170_powersave will leak the temporary command
assembly buffer.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
