When shutting down the CAN interface (ifconfig canX down) during high CAN bus
loads, the CAN core might hang and freeze the whole CPU.
This patch fixes the shutdown sequence by first disabling the CAN core then
disabling all interrupts.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is no reason to disallow building the driver on big-endian ARM kernels.
Furthermore, the current behavior is actually broken on little-endian PowerPC
as well.
The choice of register accessor functions must purely depend on the CPU
architecture, not which endianess the CPU is running on. Note that we nowadays
allow both big-endian ARM and little-endian PowerPC kernels.
With this patch applied, we will do the right thing in all four combinations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core uses the peripheral clock ("per") as basic clock for the
bit timing calculation. However the driver uses the the wrong clock ("ipg").
This leads to wrong bit rates if the rates on both clock are different.
This patch fixes the problem by using the correct clock for the bit rate
calculation.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implemetation of of_match_device() relies that the of_device_id
table in the driver is sorted from most specific to least specific compatible.
Without this patch the mx28 is detected as the less specific p1010. This leads
to a p1010 specific workaround is activated on the mx28, which is not needed.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In patch
0d1862e can: flexcan: fix flexcan_chip_start() on imx6
the loop in flexcan_chip_start() that iterates over all mailboxes after the
soft reset of the CAN core was removed. This loop put all mailboxes (even the
ones marked as reserved 1...7) into EMPTY/INACTIVE mode. On mailboxes 8...63,
this aborts any pending TX messages.
After a cold boot there is random garbage in the mailboxes, which leads to
spontaneous transmit of CAN frames during first activation. Further if the
interface was disabled with a pending message (usually due to an error
condition on the CAN bus), this message is retransmitted after enabling the
interface again.
This patch fixes the regression by:
1) Limiting the maximum number of used mailboxes to 8, 0...7 are used by the RX
FIFO, 8 is used by TX.
2) Marking the TX mailbox as EMPTY/INACTIVE, so that any pending TX of that
mailbox is aborted.
Cc: linux-stable <stable@vger.kernel.org>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/usb/qmi_wwan.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
include/net/netfilter/nf_conntrack_synproxy.h
include/net/secure_seq.h
The conflicts are of two varieties:
1) Conflicts with Joe Perches's 'extern' removal from header file
function declarations. Usually it's an argument signature change
or a function being added/removed. The resolutions are trivial.
2) Some overlapping changes in qmi_wwan.c and be.h, one commit adds
a new value, another changes an existing value. That sort of
thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the flexcan_chip_start() function first the flexcan core is going through
the soft reset sequence, then the RX FIFO is enabled.
With the hardware is put into FIFO mode, message buffers 1...7 are reserved by
the FIFO engine. The remaining message buffers are in reset default values.
This patch removes the bogus initialization of the message buffers, as it
causes an imprecise external abort on imx6.
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_set_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Using devm_ioremap_resource() can make the code simpler and smaller.
Also, place alloc_candev() after of_match_device() to make error handling
easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of using a GPIO to turn on/off the CAN transceiver, it is better to
use a regulator as some systems may use a PMIC to power the CAN transceiver.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Using SIMPLE_DEV_PM_OPS can make the code smaller and simpler.
Also change CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: <linux-can@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for canbus activity led indicators on flexcan devices by
calling appropriate can_led_* functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a MODULE_DEVICE_TABLE for the of and platform bindings, so that
the module can be loaded automatically by udev.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds some Flexcan version info and removes the feature flag
FLEXCAN_HAS_BROKEN_ERR_STATE for the i.MX6Q. It also has the line [TR]WRN_INT
properly connected.
Cc: Hui Wang <jason77.wang@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
[mkl: convert to incremental patch]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Due to a bug in most Flexcan cores, the bus error interrupt needs
to be enabled. Otherwise we don't get any error warning or passive
interrupts. This is _not_ necessary for the i.MX28 and this patch
disables bus error interrupts if "berr-reporting" is not requested.
This avoids bus error flooding, which might harm, especially on
low-end systems.
To handle such quirks of the Flexcan cores, a hardware feature flag
has been introduced, also replacing the "hw_ver" variable. So far
nobody could tell what Flexcan core version is available on what
Freescale SOC, apart from the i.MX6Q and P1010, and which bugs or
features are present on the various "hw_rev".
CC: Hui Wang <jason77.wang@gmail.com>
CC: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a second clock to the flexcan driver. On
modern freescale ARM cores like the imx53 and imx6q two clocks ("ipg"
and "per") must be enabled in order to access the CAN core.
In the original driver, the clock was requested without specifying the
connection id, further all mainline ARM archs with flexcan support
(imx28, imx25, imx35) register their flexcan clock without a
connection id, too.
This patch first renames the existing clk variable to clk_ipg and
converts it to devm for easier error handling. The connection id "ipg"
is added to the devm_clk_get() call. Then a second clock "per" is
requested. As all archs don't specify a connection id, both clk_get
return the same clock. This ensures compatibility to existing flexcan
support and adds support for imx53 at the same time.
After this patch hits mainline, the archs may give their existing
flexcan clock the "ipg" connection id and implement a dummy "per"
clock.
This patch has been tested on imx28 (unmodified clk tree) and on imx53
with a seperate "ipg" and "per" clock.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch marks the bittiming_const pointer as in the struct can_pric as
"const". This allows us to mark the struct can_bittiming_const in the CAN
drivers as "const", too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
At least in the i.MX series, the flexcan contrller divides into ver_3
and ver_10, current driver is for ver_3 controller.
i.MX6 has ver_10 controller, it has more reigsters than ver_3 has.
The rxfgmask (Rx FIFO Global Mask) register is one of the new added.
Its reset value is 0xffffffff, this means ID Filter Table must be
checked when receive a packet, but the driver is designed to accept
everything during the chip start, we need to clear this register to
follow this design.
Use the data entry of the struct of_device_id to point chip specific
info, we can set hardware version for each platform.
Cc: linux-can@vger.kernel.org
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
[mkl: add id_table support]
Tested-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
of_property_read_u32() can auto handle endian problems, use this
function can make code clean and simple.
No need to check return value here since the following got value
check will handle this.
Cc: linux-can@vger.kernel.org
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
The freescale arm i.MX series platform can support this driver, and
usually the arm cpu works in the little endian mode by default, while
device tree entry value is stored in big endian format, we should use
be32_to_cpup() to handle them, after modification, it can work well
both on the le cpu and be cpu.
Cc: stable <stable@vger.kernel.org> # v3.2+
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently the flexcan driver uses hardware local echo. This blindly
echos all transmitted frames to all receiving sockets, regardless what
CAN_RAW_RECV_OWN_MSGS and CAN_RAW_LOOPBACK are set to.
This patch now submits transmitted frames to be echoed in the transmit
complete interrupt, preserving the reference to the sending
socket. This allows the can protocol to correctly handle the local
echo.
Further this patch moves tx_bytes statistic accounting into the tx_complete
handler.
Signed-off-by: Reuben Dowle <reuben.dowle@navico.com>
[mkl: move tx_bytes accounting into tx_complete handler; cleanups]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As pointed out by Reuben Dowle and Lothar Waßmann, the TWRN_INT,
RWRN_INT, BOFF_INT interrupt sources need to be cleared as well
to avoid interrupt flooding, at least for the Flexcan on i.MX28
SOCs. Furthermore, the interrupts are only cleared, if really one
of those interrupt sources are pending (which is not the case for
rx and tx done).
Cc: Reuben Dowle <Reuben.Dowle@navico.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
The patch converts flexcan driver to clk_prepare/clk_unprepare by
using helper functions clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
This patch converts the drivers in drivers/net/can/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Kurt Van Dijck <kurt.van.dijck@eia.be>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If our CAN device's device tree node has a clock-frequency property,
then use that value for the can devices clock frequency. If not, fall
back to asking the platform/mach code for the clock frequency associated
with the flexcan device.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
On powerpc, the OpenFirmware devices are not matched without specifying
an of_match array. Introduce that array as that is used for matching
on the Freescale P1010 processor.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Make flexcan driver handle register reads in the appropriate endianess.
This was a basic search and replace and then define some inlines.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
powerpc does not have a mach-####/clock.h. When testing, I found neither
arm nor powerpc needed the mach/clock.h at all so I removed it.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: socketcan-core@lists.berlios.de
Cc: netdev@vger.kernel.org
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failed_get label is used after the call to clk_get has succeeded, so it
should be moved up above the call to clk_put.
The failed_req labels doesn't do anything different than failed_get, so
delete it.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv is part of the memory allocated by alloc_candev().
This patch moved the free it after last usage of priv.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This core is found on some Freescale SoCs and also some Coldfire
SoCs. Support for Coldfire is missing though at the moment as
they have an older revision of the core which does not have RX FIFO
support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
