This is a pure codestyle cleanup patch. No functional change intended.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What 0xFFFF means here is actually the max mtu of a ip packet. Use help
macro IP_MAX_MTU here.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new bit TX_GENF_CLR_EN has been added in AM65x SR2.0 to fix i2083
errata, which can be just set unconditionally for all SoCs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: clean up some W=1 build warnings
A collection of minor fixes to issues flagged up by W=1.
After this series, the only remaining warnings in the sfc driver are
some 'member missing in kerneldoc' warnings from ptp.c.
Tested by building on x86_64 and running 'ethtool -p' on an EF10 NIC;
there was no error, but I couldn't observe the actual LED as I'm
working remotely.
[ Incidentally, ethtool_phys_id()'s behaviour on an error return
looks strange — if I'm reading it right, it will break out of the
inner loop but not the outer one, and eventually return the rc
from the last run of the inner loop. Is this intended? ]
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
W=1 warnings indicated that 'rc' was unused in efx_mcdi_set_id_led();
change the function to return int instead of void and plumb the rc
through the caller efx_ethtool_phys_id().
Since (post-Falcon) all sfc NICs use MCDI for this, there's no point in
indirecting through a nic_type method, so remove that and just call
efx_mcdi_set_id_led() directly.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing 'struct' keyword caused "cannot understand function prototype"
warnings.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to some past refactor, 'spec' is not actually used in this
function; the code using it moved to the callee efx_farch_filter_remove.
Remove the variable to fix a W=1 warning.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these RX-event flags aren't used at all, so remove them.
Others are used only #ifdef DEBUG to log a message; suppress the
unused-var warnings #ifndef DEBUG with a void cast.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wenxu says:
====================
Add ip6_fragment in ipv6_stub
Add ip6_fragment in ipv6_stub and use it in openvswitch
This version add default function eafnosupport_ipv6_fragment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Using ipv6_stub->ipv6_fragment to avoid the netfilter dependency
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6_fragment to ipv6_stub to avoid calling netfilter when
access ip6_fragment.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel says:
====================
gtp: minor enhancements
The first patch removes a useless rcu lock and the second relax alloc
constraints when a PDP context is added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PDP context is added, the rtnl lock is held, thus no need to force
a GFP_ATOMIC.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtnl lock is taken just the line above, no need to take the rcu also.
Fixes: 1788b8569f ("gtp: fix use-after-free in gtp_encap_destroy()")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we intend to use PCS operations, mac_pcs_get_state() will not be
implemented, so will be NULL. If we also intend to register the PCS
operations in mac_prepare() or mac_config(), then this leads to an
attempt to call NULL function pointer during phylink_start(). Avoid
this, but we must report the link is down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luo bin says:
====================
hinic: add debugfs support
add debugfs node for querying sq/rq info and function table
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
add debugfs node for querying function table, for example:
cat /sys/kernel/debug/hinic/0000:15:00.0/func_table/valid
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add debugfs node for querying rq info, for example:
cat /sys/kernel/debug/hinic/0000:15:00.0/RQs/0x0/rq_hw_pi
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add debugfs node for querying sq info, for example:
cat /sys/kernel/debug/hinic/0000:15:00.0/SQs/0x0/sq_pi
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the policy export for binary attributes I erroneously used
a != NLA_VALIDATE_NONE comparison instead of checking for the
two possible values, which meant that if a validation function
pointer ended up aliasing the min/max as negatives, we'd hit
a warning in nla_get_range_unsigned().
Fix this to correctly check for only the two types that should
be handled here, i.e. range with or without warn-too-long.
Reported-by: syzbot+353df1490da781637624@syzkaller.appspotmail.com
Fixes: 8aa26c575f ("netlink: make NLA_BINARY validation more flexible")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d3b990b7f3 ("netlabel: fix problems with mapping removal")
added a check to return an error if ret_val != 0, before ret_val is
later used in a log message. Now it will unconditionally print "...
res=1". So just drop the check.
Addresses-Coverity: ("Dead code")
Fixes: d3b990b7f3 ("netlabel: fix problems with mapping removal")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson says:
====================
ionic memory usage rework
Previous review comments have suggested [1],[2] that this driver
needs to rework how queue resources are managed and reconfigured
so that we don't do a full driver reset and to better handle
potential allocation failures. This patchset is intended to
address those comments.
The first few patches clean some general issues and
simplify some of the memory structures. The last 4 patches
specifically address queue parameter changes without a full
ionic_stop()/ionic_open().
[1] https://lore.kernel.org/netdev/20200706103305.182bd727@kicinski-fedora-pc1c0hjn.dhcp.thefacebook.com/
[2] https://lore.kernel.org/netdev/20200724.194417.2151242753657227232.davem@davemloft.net/
v3: use PTR_ALIGN without typecast
fix up Neel's attribution
v2: use PTR_ALIGN
recovery if netif_set_real_num_tx/rx_queues fails
less racy queue bring up after reconfig
common-ize the reconfig queue stop and start
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert tx_timeout handler to not do the full reset. As this was
the last user of ionic_reset_queues(), we can drop it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add to our new ionic_reconfigure_queues() to also be able to change
the number of queues in use, and to change the queue interrupt layout
between split and combined.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original way of changing ring length was to completely
tear down the lif's queue structure and then rebuild it, while
running the risk of allocations that might fail in the middle
and leave us with a broken driver.
Instead, we can set up all the new queue and descriptor
allocations first, then swap them out and delete the old
allocations. If the new allocations fail, we report the error,
stay with the old setup and continue running. This gives us
a safer path, and a smaller window of time where we're not
processing traffic.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
We really don't need to tear down and rebuild the whole queue structure
when changing the MTU; we can simply stop the queues, clean and refill,
then restart the queues.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use index counters rather than pointers for tracking head
and tail in the queues to save a little memory and to perhaps
slightly faster queue processing.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the queue descriptor blocks into separate dma
allocations to make for smaller blocks.
Co-developed-by: Neel Patel <neel@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
ionic_open() and ionic_stop() are not referenced outside of their
defining file, so make them static.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a block of stats structs attached to the lif instead of
little ones attached to each qcq. This simplifies our memory
management and gets rid of a lot of unnecessary indirection.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we aren't yet supporting multiple lifs, we can remove
complexity by removing the list concept and related code,
to be re-engineered later when actually needed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kcalloc for allocating arrays of structures.
Following along after
commit e71642009cbdA ("ionic_lif: Use devm_kcalloc() in ionic_qcq_alloc()")
there are a couple more array allocations that can be converted
to using devm_kcalloc().
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC might tell us its minimum MTU, but let's be sure not
to use something smaller than ETH_MIN_MTU.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy says:
====================
Enable Fiber on DP83822 PHY
The DP83822 Ethernet PHY has the ability to connect via a Fiber port. The
derivative PHYs DP83825 and DP83826 do not have this ability. In fiber mode
the DP83822 disables auto negotiation and has a fixed 100Mbps speed with
support for full or half duplex modes.
A devicetree binding was added to set the signal polarity for the fiber
connection. This property is only applicable if the FX_EN strap is set in
hardware other wise the signal loss detection is disabled on the PHY.
If the FX_EN is not strapped the device can be configured to run in fiber mode
via the device tree. All be it the PHY will not perform signal loss detection.
v2 review from a long time ago can be found here - https://lore.kernel.org/patchwork/patch/1270958/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83822 can be configured to use a Fiber connection. The strap
register is read to determine if the device has been configured to use
a fiber connection. With the fiber connection the PHY can be configured
to detect whether the fiber connection is active by either a high signal
or a low signal.
Fiber mode is only applicable to the DP83822 so rework the PHY match
table so that non-fiber PHYs can still use the same driver but not call
or use any of the fiber features.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dt binding for the TI dp83822 ethernet phy device.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sysctl that was added earlier by commit 79134e6ce2 ("net: do
not create fallback tunnels for non-default namespaces") to create
fall-back only in root-ns. This patch enhances that behavior to provide
option not to create fallback tunnels in root-ns as well. Since modules
that create fallback tunnels could be built-in and setting the sysctl
value after booting is pointless, so added a kernel cmdline options to
change this default. The default setting is preseved for backward
compatibility. The kernel command line option of fb_tunnels=initns will
set the sysctl value to 1 and will create fallback tunnels only in initns
while kernel cmdline fb_tunnels=none will set the sysctl value to 2 and
fallback tunnels are skipped in every netns.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Zenczykowski <maze@google.com>
Cc: Jian Yang <jianyang@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Edich says:
====================
Add phylib support to smsc95xx
To allow to probe external PHY drivers, this patch series adds use of
phylib to the smsc95xx driver.
Changes in v5:
- Removed all phy_read calls from the smsc95xx driver.
Changes in v4:
- Removed useless inline type qualifier.
Changes in v3:
- Moved all MDI-X functionality to the corresponding phy driver;
- Removed field internal_phy from a struct smsc95xx_priv;
- Initialized field is_internal of a struct phy_device;
- Kconfig: Added selection of PHYLIB and SMSC_PHY for USB_NET_SMSC95XX.
Changes in v2:
- Moved 'net' patches from here to the separate patch series;
- Removed redundant call of the phy_start_aneg after phy_start;
- Removed netif_dbg tracing "speed, duplex, lcladv, and rmtadv";
- mdiobus: added dependency from the usbnet device;
- Moved making of the MII address from 'phy_id' and 'idx' into the
function mii_address;
- Moved direct MDIO accesses under condition 'if (pdata->internal_phy)',
as they only need for the internal PHY;
- To be sure, that this set of patches is git-bisectable, tested each
sub-set of patches to be functional for both, internal and external
PHYs, including suspend/resume test for the 'devices'
(5.7.8-1-ARCH, Raspberry Pi 3 Model B).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, each PHY has their own configuration and it can be done
through an external PHY driver. The smsc95xx driver uses only the
hard-coded internal PHY configuration.
This patch adds phylib support to probe external PHY drivers for
configuring external PHYs.
The MDI-X configuration for the internal PHYs moves from
drivers/net/usb/smsc95xx.c to drivers/net/phy/smsc.c.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using `void *driver_priv` instead of `unsigned long data[]` is more
straightforward way to recover the `struct smsc95xx_priv *` from the
`struct net_device *`.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes arguments netdev and phy_id from the functions
smsc95xx_mdio_read_nopm and smsc95xx_mdio_write_nopm. Both removed
arguments are recovered from a new argument `struct usbnet *dev`.
Signed-off-by: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* some code to support SAE (WPA3) offload in AP mode
* many documentation (wording) fixes/updates
* netlink policy updates, including the use of NLA_RANGE
with binary attributes
* regulatory improvements for adjacent frequency bands
* and a few other small additions/refactorings/cleanups
-----BEGIN PGP SIGNATURE-----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=Ys45
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2020-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* some code to support SAE (WPA3) offload in AP mode
* many documentation (wording) fixes/updates
* netlink policy updates, including the use of NLA_RANGE
with binary attributes
* regulatory improvements for adjacent frequency bands
* and a few other small additions/refactorings/cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Like all other network functions, let's notify gtp context on creation and
deletion.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Gabriel Ganne <gabriel.ganne@6wind.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: updates 2020-08-27
please apply the following patch series for qeth to netdev's net-next tree.
Patch 8 makes some improvements to how we handle HW address events,
avoiding some uncertainty around processing stale events after we
switched off the feature.
Except for that it's all straight-forward cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code for bridge address events has two shortcomings in its
control sequence:
1. after disabling address events via PNSO, we don't flush the remaining
events from the event_wq. So if the feature is re-enabled fast
enough, stale events could leak over.
2. PNSO and the events' arrival via the READ ccw device are unordered.
So even if we flushed the workqueue, it's difficult to say whether
the READ device might produce more events onto the workqueue
afterwards.
Fix this by
1. explicitly fencing off the events when we no longer care, in the
READ device's event handler. This ensures that once we flush the
workqueue, it doesn't get additional address events.
2. Flush the workqueue after disabling the events & fencing them off.
As the code that triggers the flush will typically hold the sbp_lock,
we need to rework the worker code to avoid a deadlock here in case
of a 'notifications-stopped' event. In case of lock contention,
requeue such an event with a delay. We'll eventually aquire the lock,
or spot that the feature has been disabled and the event can thus be
discarded.
This leaves the theoretical race that a stale event could arrive
_after_ we re-enabled ourselves to receive events again. Such an event
would be impossible to distinguish from a 'good' event, nothing we can
do about it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data returned from IPA_SBP_QUERY_BRIDGE_PORTS and
IPA_SBP_BRIDGE_PORT_STATE_CHANGE has the same format. Use a single
struct definition for it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code copies _all_ entries from the event into a worker, when we
later only need specific data from the first entry.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only time that our Bridgeport role should change is when we change
the configuration ourselves. In which case we also adjust our internal
state tracking, no need to do it again when we receive the corresponding
event.
Removing the locked section helps a subsequent patch that needs to flush
the workqueue while under sbp_lock.
It would be nice to raise a warning here in case HW does weird things
after all, but this could end up generating false-positives when we
change the configuration ourselves.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A newly initialized device is disabled for address events, there's no
need to explicitly disable them.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
