Recent firmware versions expose more DPNI counters.
Export relevant ones via ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we prepare to read more pages from the DPNI stat counters,
reorganize the code a bit to make it easier to extend.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.
Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:
PAUSE | ASYM_PAUSE | Rx pause | Tx pause
----------------------------------------
0 | 0 | disabled | disabled
0 | 1 | disabled | enabled
1 | 0 | enabled | enabled
1 | 1 | enabled | disabled
The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a link state change occurs, we get notified and save
the new link settings in the device's private data. In ethtool
get_link_ksettings, use the stored state instead of interrogating
the firmware each time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only support fixed-link for now, so there is no point in
offering users the option to change link settings via ethtool.
Functionally there is no change, since firmware prevents us from
changing link parameters anyway.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch reports a potential spectre vulnerability in the dpaa2-eth
driver, where the value of rxnfc->fs.location (which is provided
from user-space) is used as index in an array.
Add a call to array_index_nospec() to sanitize the access.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't
offer flow steering capabilities at all on these platforms,
since our driver implementation configured a "comprehensive"
FS key (containing all supported header fields), with masks
used to ignore the fields not present in the rules provided
by the user.
We now allow ethtool rules that share a common key (i.e. have
the same header fields). The FS key is now kept in the driver
private data and initialized when the first rule is added to
an empty table, rather than at probe time. If a rule with a new
composition key is wanted, the user must first manually delete
all previous rules.
When building a FS table entry to pass to firmware, we still use
the old building algorithm, which assumes an all-supported-fields
key, and later collapse the fields which aren't actually needed.
Masked rules are not supported; if provided, the mask value
will be ignored. For firmware versions older than MC10.7.0
(that only offer the legacy ABIs for configuring distribution
keys) flow steering without masking support remains unavailable.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for the XDP_REDIRECT action.
The redirected frame is transmitted and confirmed on the regular Tx/Tx
conf queues. Frame is marked with the "XDP" type in the software
annotation, since it requires special treatment.
We don't have good hardware support for TX batching, so the
XDP_XMIT_FLUSH flag doesn't make a difference for now; ndo_xdp_xmit
performs the actual Tx operation on the spot.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics for pending frames in Rx/Tx conf FQs and
number of buffers in pool. Available through ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add counters for xdp processed frames to the channel statistics.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused counter. Reorder fields in channel stats structure
to match the ethtool strings order and make it easier to print them
with ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for inserting and deleting Rx flow classification
rules through ethtool.
We support classification based on some header fields for
flow-types ether, ip4, tcp4, udp4 and sctp4.
Rx queues are core affine, so the action argument effectively
selects on which cpu the matching frame will be processed.
Discarding the frame is also supported.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the Rx flow hash key was a 5-tuple (IP src, IP dst,
IP nextproto, L4 src port, L4 dst port) fixed value that we
configured at probe.
Add support for configuring this hash key at runtime.
We support all standard header fields configurable through ethtool,
but cannot differentiate between flow types, so the same hash key
is applied regardless of protocol.
We also don't support the discard option.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA2 Ethernet driver supports Freescale/NXP SoCs with DPAA2
(DataPath Acceleration Architecture v2). The driver manages
network objects discovered on the fsl-mc bus.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
