After fixing the u32 thinko I sill had occasional hickups on ATI chipsets
with small deltas. There seems to be a delay between writing the compare
register and the transffer to the internal register which triggers the
interrupt. Reading back the value makes sure, that it hit the internal
match register befor we compare against the counter value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use the HPET only in 32bit mode because:
1) some HPETs are 32bit only
2) on i386 there is no way to read/write the HPET atomic 64bit wide
The HPET code unification done by the "moron of the year" did
not take into account that unsigned long is different on 32 and
64 bit.
This thinko results in a possible endless loop in the clockevents
code, when the return comparison fails due to the 64bit/332bit
unawareness.
unsigned long cnt = (u32) hpet_read() + delta can wrap over 32bit.
but the final compare will fail and return -ETIME causing endless
loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The minimum reprogramming delta was hardcoded in HPET ticks,
which is stupid as it does not work with faster running HPETs.
The C1E idle patches made this prominent on AMD/RS690 chipsets,
where the HPET runs with 25MHz. Set it to 5us which seems to be
a reasonable value and fixes the problems on the bug reporters
machines. We have a further sanity check now in the clock events,
which increases the delta when it is not sufficient.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Tested-by: Dmitry Nezhevenko <dion@inhex.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
AMD SB700 based systems with spread spectrum enabled use a SMM based
HPET emulation to provide proper frequency setting. The SMM code is
initialized with the first HPET register access and takes some time to
complete. During this time the config register reads 0xffffffff. We
check for max. 1000 loops whether the config register reads a non
0xffffffff value to make sure that HPET is up and running before we go
further. A counting loop is safe, as the HPET access takes thousands
of CPU cycles. On non SB700 based machines this check is only done
once and has no side effects.
Based on a quirk patch from: crane cai <crane.cai@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This fixes kernel http://bugzilla.kernel.org/show_bug.cgi?id=11112 (bogus
RTC update IRQs reported) for rtc-cmos, in two ways:
- When HPET is stealing the IRQs, use the first IRQ to grab
the seconds counter which will be monitored (instead of
using whatever was previously in that memory);
- In sane IRQ handling modes, scrub out old IRQ status before
enabling IRQs.
That latter is done by tightening up IRQ handling for rtc-cmos everywhere,
also ensuring that when HPET is used it's the only thing triggering IRQ
reports to userspace; net object shrink.
Also fix a bogus HPET message related to its RTC emulation.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Report-by: W Unruh <unruh@physics.ubc.ca>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While reading through the HPET code I realized that the
computation of .mult variables could be done with less
lines of code, resulting in a 1.6% text size saving
for hpet.o
So I propose the following patch, which applies against
today's Linus -git tree.
>From 0c6507e400e9ca5f7f14331e18f8c12baf75a9d3 Mon Sep 17 00:00:00 2001
From: Carlos R. Mafra <crmafra@ift.unesp.br>
Date: Mon, 5 May 2008 19:38:53 -0300
The computation of clocksource_hpet.mult
tmp = (u64)hpet_period << HPET_SHIFT;
do_div(tmp, FSEC_PER_NSEC);
clocksource_hpet.mult = (u32)tmp;
can be streamlined if we note that it is equal to
clocksource_hpet.mult = div_sc(hpet_period, FSEC_PER_NSEC, HPET_SHIFT);
Furthermore, the computation of hpet_clockevent.mult
uint64_t hpet_freq;
hpet_freq = 1000000000000000ULL;
do_div(hpet_freq, hpet_period);
hpet_clockevent.mult = div_sc((unsigned long) hpet_freq,
NSEC_PER_SEC, hpet_clockevent.shift);
can also be streamlined with the observation that hpet_period and hpet_freq are
inverse to each other (in proper units).
So instead of computing hpet_freq and using (schematically)
div_sc(hpet_freq, 10^9, shift) we use the trick of calling with the
arguments in reverse order, div_sc(10^6, hpet_period, shift).
The different power of ten is due to frequency being in Hertz (1/sec)
and the period being in units of femtosecond. Explicitly,
mult = (hpet_freq * 2^shift)/10^9 (before)
mult = (10^6 * 2^shift)/hpet_period (after)
because hpet_freq = 10^15/hpet_period.
The comments in the code are also updated to reflect the changes.
As a result,
text data bss dec hex filename
2957 425 92 3474 d92 arch/x86/kernel/hpet.o
3006 425 92 3523 dc3 arch/x86/kernel/hpet.o.old
a 1.6% reduction in text size.
Signed-off-by: Carlos R. Mafra <crmafra@ift.unesp.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Al Viro pointed out that there's a missing readl() of timer->hpet_config,
found by Sparse.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the magic number in the third argment of div_sc().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The commits:
commit 37a47db8d7
Author: Balaji Rao <balajirrao@gmail.com>
Date: Wed Jan 30 13:30:03 2008 +0100
x86: assign IRQs to HPET timers, fix
and
commit e3f37a54f6
Author: Balaji Rao <balajirrao@gmail.com>
Date: Wed Jan 30 13:30:03 2008 +0100
x86: assign IRQs to HPET timers
have been identified to cause a regression on some platforms due to
the assignement of legacy IRQs which makes the legacy devices
connected to those IRQs disfunctional.
Revert them.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=10382
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
the previous patch in the old RTC driver. It also removes the direct
rtc_interrupt() call from arch/x86/kernel/hpetc.c so that there's finally no
(code) dependency to CONFIG_RTC in arch/x86/kernel/hpet.c.
Because of this, it's possible to compile the drivers/char/rtc.ko driver as
module and still use the HPET emulation functionality. This is also expressed
in Kconfig.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
enabled, then interrupts don't work for the rtc-cmos driver which results in
RTC_AIE*, RTC_PIE* and RTC_ALM being unusable. This affects hwclock from
util-linux-ng at least on i386 since that uses RTC_PIE_ON. (For x86-64, a
polling method is used for unknown reasons.)
This patch series now
1. export the functions from arch/x86/kernel/hpet.c that the old char/rtc
driver uses to work around that problem,
2. makes it possible to compile the old rtc driver as module, while still
having CONFIG_HPET_EMULATE_RTC enabled and
3. makes use of the exported functions in (1) in the new rtc-cmos driver.
This patch:
This patch makes the RTC emulation functions in arch/x86/kernel/hpet.c usable
for kernel modules. It
- exports the functions (EXPORT_SYMBOL_GPL()),
- adds an interface to register the interrupt callback function
instead of using only a fixed callback function and
- replaces the rtc_get_rtc_time() function which depends on
CONFIG_RTC with a call to get_rtc_time() which is defined in
include/asm-generic/rtc.h.
The only dependency to CONFIG_RTC is the call to rtc_interrupt() which is
removed by the next patch. After this, there's no (code) dependency of
this functions to CONFIG_RTC=y any more.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Robert Picco <Robert.Picco@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lucas Woods <woodzy@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Looks like IRQ 31 is assigned to timer 3, even without the patch!
I wonder who wrote the number 31. But the manual says that it is
zero by default.
I think we should check whether the timer has been allocated an IRQ before
proceeding to assign one to it. Here is a patch that does this.
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The userspace API for the HPET (see Documentation/hpet.txt) did not work. The
HPET_IE_ON ioctl was failing as there was no IRQ assigned to the timer
device. This patch fixes it by allocating IRQs to timer blocks in the HPET.
arch/x86/kernel/hpet.c | 13 +++++--------
drivers/char/hpet.c | 45 ++++++++++++++++++++++++++++++++++++++-------
include/linux/hpet.h | 2 +-
3 files changed, 44 insertions(+), 16 deletions(-)
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I was confused by FSEC = 10^15 NSEC statement, plus small whitespace
fixes. When there's copyright, there should be GPL.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the current code, RTC_AIE doesn't work if the RTC relies on
CONFIG_HPET_EMULATE_RTC because the code sets the RTC_AIE flag in
hpet_set_rtc_irq_bit(). The interrupt handles does accidentally check
for RTC_PIE and not RTC_AIE when comparing the time which was set in
hpet_set_alarm_time().
I now verified on a test system here that without the patch applied,
the attached test program fails on a system that has HPET with
2.6.24-rc7-default. That's not critical since I guess the problem has
been there for several kernel releases, but as the fix is quite
obvious.
Configuration is CONFIG_RTC=y and CONFIG_HPET_EMULATE_RTC=y.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If HPET was enabled by pci quirks, we use i8253 as initial clockevent
because pci quirks doesn't run until pci is initialized.
The above means the kernel (or something) is assuming HPET legacy
replacement is disabled and can use i8253 at boot.
If we used kexec, it isn't true. So, this patch disables HPET legacy
replacement for kexec in machine_shutdown().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
add force_hpet boot option.
(this will be useful to make the forced-enable quirks depend on.)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
force_enable hpet for ICH5.
[ Build fixes from Andrew Morton ]
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Enable HPET later during boot, after the force detect in PCI quirks. Also add
a call to repeat the force enabling at resume time.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Restructure and rename legacy replacement mode HPET timer support. Just the
code structural changes and should be zero functionality change.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove hpet_readl/writel from vsyscall.h, where it does not belong
anyway. Use the hpet code itself.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Remove the unused code after the switch to clock events.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>