The requested bit rate can be outside the range supported by the driver.
The maximum bit rate this driver supports at the moment is 400Khz.
If the requested bit rate is larger than the maximum supported by the
driver, set the bitrate to the maximum supported before bitrate_khz is
calculated.
Maximum speed supported by the driver can be increased to 1Mhz by
adding support for "fast plus mode" in the future.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clear line status and all generated interrupts from the interrupt
status register before starting a transfer, as we may have
unserviced interrupts from previous transfers that might be
handled in the context of the new transfer.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c->line_status accumulates the line status bits that have been seen
with each interrupt. As we're only interested in that bit from the
current interrupt, refer to line_status (the argument to img_i2c_auto)
instead of i2c->line_status.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, after determining the minimum value for the High period
(TCKH) the remainder of the internal clock pulses is set as the Low
period (TCKL). This causes the i2c clock duty cycle to be much less
than 50%.
Modify the starting position to TCKH and TCKL at 50% of the internal
clock, and adjusts the TCKH and TCKL values from there should the
minimum value for TCKL not be met. This results in duty cycles closer
to 50%.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using % can be slow depending on the architecture.
Using DIV_ROUND_UP is nicer and more efficient way to do it.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move scb_wr_rd_fence to before reading from fifo and writing to
fifo to make sure the the first read/write is done after the required
number of cycles.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The code to read from the master read fifo, and write to the master
write fifo, checks a bit in an SCB register before every byte to
ensure that the fifo is not full (write fifo) or empty (read fifo).
Due to clock domain crossing inside the SCB block the updated value
of this bit is only visible after 2 cycles.
The scb_wr_rd_fence() function does 2 dummy writes (to the read-only
revision register), and it's called before reading from or writing to the
fifos to ensure that subsequent reads of the fifo status bits do not read
stale values.
As the 2 dummy writes are required in all versions of the ip, the version
check is dropped.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated. To keep the race window as small as
possible, we clear it right at the beginning of the interrupt. We don't
need checking since we always want to stop START and STOP generation on
the next occasion after we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to broken HW design, master IRQs are more timing critical, so give
them precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We make sure to reinit the HW in the timeout case; then we know that
interrupts are always disabled in the sections protected by the
spinlock. Thus, we can simply remove it which is a preparation for
further refactoring. While here, rename the timeout variable to
time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Features:
- new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
- core: scans DT and assigns wakeup interrupts. no driver changes needed.
- core: some refcouting issues fixed and better API for that
- core: new helper function for best effort block read emulation
- slave framework: proper DT bindings and userspace instantiation
- some bigger work for xiic, pxa, omap drivers
.. and quite a number of smaller driver fixes, cleanups, improvements"
* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
i2c: mux: reg Change ioread endianness for readback
i2c: mux: reg: fix compilation warnings
i2c: mux: reg: simplify register size checking
i2c: muxes: fix leaked i2c adapter device node references
i2c: allow specifying separate wakeup interrupt in device tree
of/irq: export of_get_irq_byname()
i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
i2c: Replace I2C_CROS_EC_TUNNEL dependency
eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
i2c: core: Add support for best effort block read emulation
i2c: lpc2k: add driver
i2c: mux: Add register-based mux i2c-mux-reg
i2c: dt: describe generic bindings
i2c: slave: print warning if slave flag not set
i2c: support 10 bit and slave addresses in sysfs 'new_device'
i2c: take address space into account when checking for used addresses
i2c: apply DT flags when probing
i2c: make address check indpendent from client struct
i2c: rename address check functions
i2c: apply address offset for slaves, too
...
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
The dma_mapping_error() function returns true if there is an error, it
doesn't return an error code. We should return -ENOMEM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The ChromeOS EC tunnel I2C bus driver depend on CROS_EC_PROTO but
MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the I2C bus driver
is registered by the ChromeOS EC mfd driver, I2C_CROS_EC_TUNNEL
really depends on MFD_CROS_EC. And because this config option
selects CROS_EC_PROTO, that dependency is met as well. So make the
driver to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.
The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When occur i2c ack error, i2c controller generate two interrupts,
first is the ack error interrupt, then the complete interrupt.
i2c interrupt handler should keep the two interrupt value, and only
call complete() for the complete interrupt.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reset DMA in hardware init function to avoid unknown hardware state
before do any I2C operation.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog resources
have been moved to reside under the i801 SMBus host controller whereas
previously they were under the LPC device.
In order to support the iTCO watchdog on newer PCHs we need to create the
platform device here in the SMBus driver and pass all known resources using
platform data.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Minor clean up of indenting, no functional change
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[wsa: squashed two lines into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The owner of the adapter is missing, while this driver is tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Printing adapter name is irrelevant from this debug print and makes output
needlessly long. Having already device and functions names printed here is
enough for debugging.
While at it remove extra space from "enabled= 0x" and use "%#x" for
printing "0x" prefixed hexadecimal values.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made it a oneliner]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for VCT-jig parallel port I2C adapter to i2c-parport.
The adapter schematic can be found here (in the RAR file):
http://remont-aud.net/shop/22/desc/vct-jig-komplekt-dlja-samostojatelnoj-sborki
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cadence 1.0 version has bugs which have been fixed in the cadence 1.4 version.
This patch removes the quirks present in the driver for cadence 1.4 version.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
[wsa: fixed indentation issues in r1p10_i2c_def]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra I2C controller required to configure the clock divisor
register inside controller to different value based on the clock
speed. The recommended clock divisor for the I2C controller for
standard/fast mode is 0x19 and for fast-mode plus is 0x10.
Add support to configure clock divisor register of I2C controller
based on bus clock rate.
This clock divisor is supported form T114 onwards.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Once the new configuration is set on the conifg register of
I2C controller, it is require to update the CONFIG_LOAD register
to transfer the new SW configuration to actual HW internal
registers that would be used in the actual logic.
It is like, SW is programming only shadow registers through
regular configuration and when these load_config bit fields
are set to 1, it causes the regular/shadows registers
configuration transferred to the HW internal active registers.
So SW has to set these bit fields at the end of all regular
registers configuration. And these config_load bits are HW
auto-clear bits. HW clears these bit fields once the register
configuration is moved to HW internal active registers. So SW
has to wait until these bits are auto-cleared before going
for any further programming
This mechanism is supported on T124 and after this SoCs.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Patch "i2c: omap: abolish variable name confusion" triggered a
coccinelle warning which we fix here:
drivers/i2c/busses/i2c-omap.c:1333:5-24: pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at line 1334
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of error conditions like Arbitration lost or NACK lets signal
the waiting process.
Handle error cases in the Rx path
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently only one interrupt is serviced in the isr.
In case the multiple interrupts happen simultenously we service and ack
only one of them. Check for all the causes in the isr and service them.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently there is no slave mode support in the driver
also in the isr we just ack it and do nothing.
So disable the AAS interrupt.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the busy loop while waiting for bus busy.
Instead let the processor sleep.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently before every transfer the interrupts are disabled.
So incase the slave nacks in the middle of the transfer the
current transfer is not aborted. Upon enabling the interrupts
conditions like NACK , arbitration lost will not be masked.
Remove the disabling of the interrupts.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently before every transfer the controller is reinitialised.
We are already resetting the controller upon errors so upon every
transfer is a performance kill.
Remove the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The xiic_process is a 154 line code that runs in isr context currently
move it to thread context. Also the name xiic_process suggests that the
intension was to run in process context.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
[wsa: initialized irqreturn_t to IRQ_NONE instead of IRQ_HANDLED]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the interrupts are disabled at the start of the
isr and enabled at the end of the isr. Remove the same.
In case the slave device NACKs the transaction while in the isr
the transfer will continue and the NACK interrupt will arrive
only after the isr is serviced.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch cleans up i2c_pxa_probe() function,
- Use devm_ variants wherever
This will clean both probe exit and i2c_pxa_remove() functions
- Check platform resource before parsing any other data from DT/platform
- Use dev_err on failure from i2c_add_numbered_adapter()
- Use pr_info instead of printk for KERN_INFO
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: removed unneeded error prinout after devm_ioremap_resource]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update i2c_pxa_scream_blue_murder() fn to print more information
in case of error.
Also, use dev_err variants instead of printk.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix below warning message, coming from 64 bit toolchain.
drivers/i2c/busses/i2c-pxa.c:1237:15:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Yipeng Yao <ypyao@marvell.com>
[vaibhav.hiremath@linaro.org: Updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of timeout in pio mode of operation return I2C_RETRY.
This behavior will be same as interrupt mode of operation.
Signed-off-by: Shouming Wang <wangshm@marvell.com>
[vaibhav.hiremath@linaro.org: Updated changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Normally i2c controller works as master, so slave addr is not needed, or
it will impact some slave device (eg. ST NFC chip) i2c accesses, because
it has the same i2c address with controller.
For example,
On the pxa1928 based platform, where PMIC (88pm860) is present @0x30
address on TWSI0 interface, and if we set 0x30 as a slave address in
pxa1928 TWSI0 module, all the transactions towards PMIC would go for toss.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During suspend there may still be some i2c access happening, as the
interrupt is shared between multiple drivers.
And if we don't keep i2c irq ON, there may be i2c access timeout if
i2c is in irq mode of operation.
Signed-off-by: Raul Xiong <xjian@marvell.com>
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
[vaibhav.hiremath@linaro.org: updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
we're about to remove the module, so we can't
really schedule a PM transition in the future,
we must wait for it to finish.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct device pointers are usually called
dev. Calling our struct omap_i2c_dev pointers
also dev has caused enough confusion.
This is the result of a few simple sed rules
to convert all struct omap_i2c_dev pointers
to be called omap instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
