Enforcing this flag in RxConfig for the mentioned chips fixes netdev
watchdog issues prepended with AMD IOMMU message(s) like:
AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x001d address=0x0000000000003000 flags=0x0050]
Note that this flag is also set in Realtek's own driver for these chips.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Alexander Lindqvist <alexander@bitspace.se>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function r8169_csum_workaround is called in the ndo_start_xmit path of
the r8169 driver. As such it should not be using dev_kfree_skb as it is
not irq safe, so instead we should be using dev_kfree_skb_any for freeing
in the dropped path, and dev_consume_skb_any for any frames that were
transmitted.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are certain regressions which are pointing to
these two commits which we are having a hard time
resolving. So revert them for now.
Specifically this reverts:
commit 0bec3b700d
Author: Florian Westphal <fw@strlen.de>
Date: Wed Jan 7 10:49:49 2015 +0100
r8169: add support for xmit_more
and
commit 1e91887685
Author: Florian Westphal <fw@strlen.de>
Date: Wed Oct 1 13:38:03 2014 +0200
r8169: add support for Byte Queue Limits
There were some attempts by Eric Dumazet to address some obvious
problems in the TX flow, to see if they would fix the problems,
but none of them seem to help for the regression reporters.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
Replace a magic number with a PCI #define symbol.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay update of hw tail descriptor if we know that another skb is going
to be sent.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For linux-3.18.0
The driver lacks netif_napi_del in the normal path and error path
to match the call of netif_napi_add in rtl8139_init_one.
This patch fixes this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For linux-3.18.0
When pci_request_regions is failed in rtl8139_init_board, pci_disable_device
is not called to disable the device which are enabled by pci_enable_device,
because of disable_dev_on_err is not assigned 1.
This patch fix this problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ephy parameter to rtl8168g.
Also change the common function of rtl8168g from "rtl_hw_start_8168g_1" to
"rtl_hw_start_8168g". And function "rtl_hw_start_8168g_1" is used for
setting rtl8168g hardware parameters.
Following is the explanation of what hardware parameter change for.
rtl8168g may erroneous judge the PCIe signal quality and show the error bit
on PCI configuration space when in PCIe low power mode.
The following ephy parameters are for above issue.
{ 0x00, 0x0000, 0x0008 }
{ 0x0c, 0x37d0, 0x0820 }
{ 0x1e, 0x0000, 0x0001 }
rtl8168g may return to PCIe L0 from PCIe L0s low power mode too slow.
The following ephy parameter is for above issue.
{ 0x19, 0x8000, 0x0000 }
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8169 use a pair of wmb() calls when setting up the descriptor rings.
The first is to synchronize the descriptor data with the descriptor status,
and the second is to synchronize the descriptor status with the use of the
MMIO doorbell to notify the device that descriptors are ready. This can
come at a heavy price on some systems, and is not really necessary on
systems such as x86 as a simple barrier() would suffice to order store/store
accesses. As such we can replace the first memory barrier with
dma_wmb() to reduce the cost for these accesses.
In addition the r8169 uses a rmb() to prevent compiler optimization in the
cleanup paths, however by moving the barrier down a few lines and replacing
it with a dma_rmb() we should be able to use it to guarantee
descriptor accesses do not occur until the device has updated the DescOwn
bit from its end.
One last change I made is to move the update of cur_tx in the xmit path to
after the wmb. This way we can guarantee the device and all CPUs should
see the DescOwn update before they see the cur_tx value update.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces most of the calls to netdev_alloc_skb_ip_align in the Realtek
drivers. The one instance I didn't replace in 8139cp.c is because it was
called as a part of init and as such is not always accessed from the
softirq context.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace rtl_skb_pad with eth_skb_pad since they do the same thing.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cmac engine is the bridge between driver and dash firmware.
Other os may not disable cmac when leave. And r8169 did not allocate any
resources for cmac engine. Disable it to prevent abnormal system behavior.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8168G/GU/H/EP and RTL8411B remove enable tx/rx from its own hw_start
function. This will prevent enable tx/rx before complete hardware tx/rx
setting.
Tx/Rx will be enabled in the end of function rtl_hw_start_8168.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Ben Hutchings drivers that allow using VLAN have to
provide enough headroom for the VLAN tags.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver allows MTU up to 1518 bytes which is not enought to run
batman-adv. Simply raise the maximum packet size up to the maximum
allowed by the transmit descriptor, 1792 bytes, giving a maximum MTU
of 1774 bytes.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the default ndo_change_mtu callback with one that allow
setting MTU that the driver can handle.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several warnings and errors of coding style rules corrected.
Compile tested.
Signed-off-by: Roberto Medina <robertoxmed@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8168EP is Realtek PCIe Gigabit Ethernet controller with DASH support.
It is a successor chip of RTL8168DP.
For RTL8168EP, the read/write ocp register is via eri channel type 2, so I
move ocp_xxx() related functions under rtl_eri_xxx. And use r8168dp_ocp_xxx()
for RTL8168DP ocp read/write, r8168ep_ocp_xxx() for RTL8168EP ocp read/write.
The way of checking dash enable is different with RTL8168DP. I use
r8168dp_check_dash()for RTL8168DP and r8168ep_check_dash() for RTL8168EP,
to check if dash is enabled.
The driver_start() and driver_stop() of RTL8168EP is also different with
RTL8168DP. I use rtl8168dp_driver_xxx() for RTL8168DP and
rtl8168ep_driver_xxx for RTL8168EP.
Right now, RTL8168EP phy mcu did not need firmware code patch, so I did not
add firmware code for it.
so I did not add firmware code for it.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions are used to inform dash firmware that driver is been
brought up or brought down. So call these two functions only when hardware dash
function is enabled.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function "rtl8168_oob_notify", using function "rtl_eri_write" to access
eri register 0xe8, instead of using MAC register "ERIDR" and "ERIAR" to
access it.
For using function "rtl_eri_write" in function "rtl8168_oob_notify", need to
move down "rtl8168_oob_notify" related functions under the function
"rtl_eri_write".
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DASH function not only RTL8168DP can support, but also RTL8168EP.
So change the name of function "r8168dp_check_dash" to "r8168_check_dash".
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of function "rtl_w1w0_eri" to "rtl_w0w1_eri".
In this function, the local variable "val" is "write zeros then write ones".
Please see below code.
(val & ~m) | p
In this patch, change the function name from "xx_w1w0_xx" to "xx_w0w1_xx".
The changed function name is more suitable for it's behavior.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change function name from "rtl_w1w0_phy" to "rtl_w0w1_phy".
And its behavior from "write ones then write zeros" to
"write zeros then write ones".
In Realtek internal driver, bitwise operations are almost "write zeros then
write ones". For easy to port hardware parameters from Realtek internal driver
to Linux kernal driver "r8169", we would like to change this function's
behavior and its name.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8168F RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8402 RTL8107E,
the magic packet enable bit is changed to eri 0xde bit0.
In this patch, change magic packet enable bit of these chips to eri 0xde bit0.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8106EUS RTL8402 can
support get mac address from backup mac address register.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an extra semi-colon so __rtl8169_set_features() is called every
time.
Fixes: 929a031dfd ('r8169: adjust __rtl8169_set_features')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>--
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the "changed" test in __rtl8169_set_features(). Instead, do
simple test in rtl8169_set_features().
Set the RxChkSum and RxVlan through __rtl8169_set_features() in
rtl_open().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setting should depend on the new features not the current one.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the parameter "features" of __rtl8169_set_features() is equal to
dev->features, the variable "changed" is alwayes 0, and nothing would
be changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leftover from 6e1d0b8988 ("r8169:add
support for RTL8168H and RTL8107E").
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8168H is Realtek PCIe Gigabit Ethernet controller.
RTL8107E is Realtek PCIe Fast Ethernet controller.
This patch add support for these two chips.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch use the struct pci_device_id instead of using macro
DEFINE_PCI_DEVICE_TABLE which is deprecated and should not be used.
And also moves these ids after probe and remove functionalities.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts to use the macro module_pci_driver, which makes
the code smaller and simpler.
Previously in this driver we are having driver version info will be
printed log buffer based on whether the driver selected as module
or statically into image itself. By using the module_pci_driver that
part of the code removed. For the first time of the device init,
we are making the version info to be printed once.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet port on my ASUS A88X Pro mainboard stopped working
several times a day, with messages like these in dmesg:
AMD-Vi: Event logged [IO_PAGE_FAULT device=05:00.0 domain=0x001e address=0x0000000000003000 flags=0x0050]
Searching the web for these messages led me to similar reports about
different hardware supported by r8169, and eventually to commits
3ced8c955e ('r8169: enforce RX_MULTI_EN
for the 8168f.') and eb2dc35d99 ('r8169:
RxConfig hack for the 8168evl'). So I tried this change, and it fixes
the problem for me.
Signed-off-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the IPv6 hw checksum for RTL8111C and later chips. Note
that the hw has the limitation for the transport offset. The
checksum must be calculated by sw, when the transport offset is
out of the range which the hw accepts.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace large send with giant send for TSO for RTL8111C and later ICs.
The large send setting of the RTL8111DP is different from the other
chips. However, the giant send setting is the same for all the chips
which support it. Use the giant send to synchronize the settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the txd_version, split rtl8169_tso_csum() into
rtl8169_tso_csum_v1() and rtl8169_tso_csum_v2().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
