xt875 comes up with a iva voltage of 1375000 and android runs at this too. fix
maximum voltage to be consistent with this.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the i2c timings in high-speed mode do not work properly to
allow us to clear I2C_DISABLE bits for PRM_VOLTCTRL register and the
device reboots if I2C_DISABLE bits are cleared.
Let's configure the voltage controller i2c for low-speed mode as done in
the Motorola Mapphone Android Linux kernel. This saves us about 7mW of
power during retention compared to the high-speed values.
Let's also change the low-speed warning to pr_info about relying on the
bootloader configured low-speed values like we currently do.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix sparse warnings:
arch/arm/mach-omap2/pmic-cpcap.c:29:15: warning: symbol 'omap_cpcap_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/pmic-cpcap.c:43:15: warning: symbol 'omap_cpcap_uv_to_vsel' was not declared. Should it be static?
arch/arm/mach-omap2/pmic-cpcap.c:93:15: warning: symbol 'omap_max8952_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/pmic-cpcap.c:107:15: warning: symbol 'omap_max8952_uv_to_vsel' was not declared. Should it be static?
arch/arm/mach-omap2/pmic-cpcap.c:140:15: warning: symbol 'omap_fan535503_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/pmic-cpcap.c:155:15: warning: symbol 'omap_fan535508_vsel_to_uv' was not declared. Should it be static?
arch/arm/mach-omap2/pmic-cpcap.c:173:15: warning: symbol 'omap_fan535503_uv_to_vsel' was not declared. Should it be static?
arch/arm/mach-omap2/pmic-cpcap.c:192:15: warning: symbol 'omap_fan535508_uv_to_vsel' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can configure voltage controller for cpcap with the data available in
Motorola Mapphone Android Linux kernel. Let's add it so we can have droid4
behave the same way for voltage controller as other omap4 devices and save
some power when idle.
Note that we're now using high-speed i2c mode, looks like the Motorola
kernel had a typo using 0x200 instead of 200 for the timings which may
caused it to not work properly.
Also note that in the long run, this should just become dts data for a
voltage controller device driver. But let's get things working first to
make it possible to test further changes easily.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
