roce interface is suppored only on Skyhawk-R.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SEMAPHORE register was being accessed from the csr BAR space. This BAR
may not be available in some Skyhawk-R configurations. Instead, access this
register via the PCI config space (it's available there too).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) separate NIC and roce bar mapping code
2) parse sli_intf::if_type inside be_map_pci_bars() as if_type must be
used only to identify bars.
3) Use pci_iomap/unmap() routines
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SKYHAWK_FAMILY will not identify all revisions of the chip.
Use device-id check (skyhawk_chip() macro) instead.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter->generation was being incorrectly set as BE_GEN3 for Skyhawk-R.
Replace generation usage with XXX_chip() macros to identify the chip.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not assume reserve fields to be don't cares as fields may change.
Clearing data structures before using.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 currently uses a too high tx coalescing setting, deferring
TX completion interrupts by up to 128 us.
With the recent skb_orphan() removal in commit 8112ec3b87,
performance of a single TCP flow is capped to ~4 Gbps, unless
we increase tcp_limit_output_bytes.
I suggest using 16 us instead of 128 us, allowing a finer control.
Performance of a single TCP flow is restored to previous levels,
while keeping TCP small queues fully enabled with default sysctl.
This patch is also a BQL prereq.
Reported-by: Vimalkumar <j.vimal@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On gcc 4.7, we will get alignment traps in the ip stack if we don't align
the ip headers on receive. The h/w can support this, so use ip aligned
allocations.
Cut down the unnecessary padding on the allocation. The buffer can start on
any byte alignment, but the size including the begining offset must be 8
byte aligned. So the h/w buffer size must include the NET_IP_ALIGN offset.
Thanks to Eric Dumazet for the initial patch highlighting the padding issues.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only generate tx interrupts on every ring size / 4 descriptors. Move the
netif_stop_queue call to the end of the xmit function rather than
checking at the beginning.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupts have already been cleared, so we don't need to clear them
again. Also, we could miss interrupts if they are cleared, but we don't
process the packet.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard readl/writel accessors involve a spinlock and cache sync
operation on ARM platforms with an outer cache. Only DMA triggering
accesses need this, so use the raw variants instead in the critical paths.
The relaxed variants would be more appropriate, but don't exist on all
arches.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New received frames will trigger the rx DMA to poll the DMA descriptors,
so there is no need to tell the h/w to poll. We also want to enable
dropping frames from the fifo when there is no buffer.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the tx dma to start reading the next frame while sending the current
frame.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instead of making separate tg3_napi_disable() and netif_tx_disable() calls.
Update version to 3.126.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 5717C0 which is a 5720A0 with special bonds-out option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed some coding style issues.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl throws error message for the current code. This patch fixes
this coding style issue.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Jitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following chips need to enable internal settings to let ASPM
and clock request work.
RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use WARN rather than printk followed by WARN_ON(1), for conciseness.
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression list es;
@@
-printk(
+WARN(1,
es);
-WARN_ON(1);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building atp.o triggers this GCC warning:
drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]
GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().
But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW driver remaps two different IO regions, but fails to unmap them
both. This patch fixes the issue by calling iounmap in the appropriate
places.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings recently came up with a better way to handle the kconfig
dependencies for the PTP hardware clocks. This patch converts one new and
one older driver to the new scheme.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_35 includes no multicast hardware filter.
Signed-off-by: Nathan Walp <faceprint@faceprint.com>
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This regression was spotted between Debian squeeze and Debian wheezy
kernels (respectively based on 2.6.32 and 3.2). More info about
Wake-on-LAN issues with Realtek's 816x chipsets can be found in the
following thread: http://marc.info/?t=132079219400004
Probable regression from d4ed95d796e5126bba51466dc07e287cebc8bd19;
more chipsets are likely affected.
Tested on top of a 3.2.23 kernel.
Reported-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Tested-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Hinted-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some driver uses tasklet_disable in device remove/close process,
tasklet_disable will inc tasklet->count and return. If the tasklet
is not handled yet because some softirq pressure, the tasklet will
placed on the tasklet_vec, never have a chance to excute. This might
lead to ksoftirqd heavy loaded, wakeup with pending_softirq, but
tasklet is disabled. tasklet_kill should be used in this case.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in
rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit b27393aecf
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function name should include '_ether_addr'.
Return type should be bool.
Parameter name should be 'addr' not 'dest' (also matching kernel-doc).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was missed in commit a24006ed12
('ptp: Enable clock drivers along with associated net/PHY drivers')
which enabled sfc's clock driver unconditionally.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to igb, ixgbe and e1000.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for the FEC(MX6) that offers time
stamping and a PTP haderware clock. Because FEC\ENET(MX6)
hardware frequency adjustment is complex, we have implemented
this in software by changing the multiplication factor of the
timecounter.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new file fec_ptp.c will use fec_enet_private to support 1588 PTP
move such structure to common header file fec.h
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch hooks into the CPTS code and adds support for the HWTSTAMP
ioctl. The patch includes code for the CPSW version found in the dm814x
even though the background device tree support for this board is still
missing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a way to configure the CPTS input clock scaling factors
via the device tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because time stamping on both external ports of the switch simultaneously
is positively useless from the application's point of view, this patch
provides a DT configuration method to choose the active port.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a driver for the CPTS that offers time
stamping and a PTP hardware clock. Because some of the
CPTS hardware variants (like the am335x) do not support
frequency adjustment, we have implemented this in software
by changing the multiplication factor of the timecounter.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the cpsw driver to operate correctly with both the
dm814x and the am335x versions of the switch hardware.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch lets the CPSW driver remember the version number in order to
support the two different variants already in the wild.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding multicast address to ALE table via netdev ops to subscribe, transmit
or receive multicast frames to and from the network
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: adapt the error path, remove unneeded headers]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ethernet frame payload word-aligned, possibly making the
memcpy into the skb a bit faster. This will be even more important
after we eliminate the copy altogether.
Also eliminate the redundant RX_OFFSET constant -- it has the same
definition and purpose as NET_IP_ALIGN.
Signed-off-by: Havard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle all TX errors, not only underruns. TX error management is
deferred to a dedicated workqueue.
Reinitialize the TX ring after treating all remaining frames, and
restart the controller when everything has been cleaned up properly.
Napi is not stopped during this task as the driver only handles
napi for RX for now.
With this sequence, we do not need a special check during the xmit
method as the packets will be caught by TX disable during workqueue
execution.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macb_get_regs() ethtool function and its helper function:
macb_get_regs_len().
The version field is deduced from the IP revision which gives the
"MACB or GEM" information. An additional version field is reserved.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of masking head and tail every time we increment them, just let them
wrap through UINT_MAX and mask them when subscripting. Add simple accessor
functions to do the subscripting properly to minimize the chances of messing
this up.
This makes the code slightly smaller, and hopefully faster as well. Also,
doing the ring buffer management this way will simplify things a lot when
making the ring sizes configurable in the future.
Available number of descriptors in ring buffer function by David Laight.
Signed-off-by: Havard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some revision of GEM, TSR status register has more information.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function has little meaning so remove it altogether and
let ethtool core fill in the fields automatically.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert some noisy netdev_dbg() statements to netdev_vdbg(). Defining
DEBUG will no longer fill up the logs; VERBOSE_DEBUG still does.
Add one more verbose debug for ISR status.
Signed-off-by: Havard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, add ISR status]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a couple of unneeded barriers and document the remaining ones.
Signed-off-by: Havard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Gigabit Ethernet mode to GEM cadence IP and enable RGMII connection.
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BF518 has a PTP time unit that works in a similar way to other MAC
based clocks, like gianfar, ixp46x, and igb. This patch adds support for
using the blackfin as a PHC. Although the blackfin hardware does offer a
few ancillary features, this patch implements only the basic operations.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the sys time stamps and timecompare code with simple
raw hardware time stamps in nanosecond resolution. The only tricky bit is
to find a PTP Hardware Clock period slower than the input clock period
and a power of two.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware time stamping code is a compile time option for the blackfin.
When it is not enabled, the driver should fall back to the standard
ethtool reply to the get_ts_info query.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where a PTP clock driver is associated with a net or PHY driver, it
should be enabled automatically whenever that driver is enabled.
Therefore:
- Make PTP clock drivers select rather than depending on PTP_1588_CLOCK
- Remove separate boolean options for PTP clock drivers that are built
as part of net driver modules. (This also fixes cases where the PTP
subsystem is wrongly forced to be built-in.)
- Set 'default y' for PTP clock drivers that depend on specific net
drivers but are built separately
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware clock drivers that select PTP_1588_CLOCK must currently
also select PPS. For those drivers that don't, the user must enable
PPS, then enable PTP_1588_CLOCK, then the driver. Simplify things for
developers and users by putting this selection in one place.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are now established subsystems, and we want drivers to be able
to select PPS and PTP_1588_CLOCK without depending on EXPERIMENTAL.
Further, the use of EXPERIMENTAL is now deprecated in general.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of link flap avoidance between PXE boot and bnx2x, set the appropriate
PHY DEVAD even if LFA kicks in.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 1G KR link by restoring CL72 misc control register to default value rather
than 0.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: Stable <stable@vger.kernel.org> [3.5]
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000 driver currently does not protect concurrent accesses to the PHY
from both the ethtool callbacks, and from the e1000_watchdog function. This
patchs adds a new spinlock which is used by e1000_{read,write}_phy_reg in
order to serialize concurrent accesses to the PHY.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where the driver would crash when trying to
write a word to the EEPROM on i210 devices.
Reported-by: Ekman Tsang <Ekman.Tsang@riverbed.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i211's one-time programmable (invm) version field is different than the
other fields contained in it. This patch adds a function to get the invm version
of it and store it for output from ethtool.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes a workaround that was needed on pre-release hardware.
Released hardware should not have this setting, but any devices that do
will get a warning message instead.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The q_vector->itr check in ixgbe_configure_tx_ring() was done prior to it
being set, which resulted in TXDCTL.WTHRESH always being set to 1 on driver
load, while consequent resets would set it to 8.
This patch moves the setting of q_vector->itr in ixgbe_alloc_q_vector() to
make sure that TXDCTL.WTHRESH is set to 8 by default.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug in ixgbe_ptp_check_pps_event where the type was
uninitialized and could cause unknown event outcomes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe, ixgbevf, igbvf, igb and
networking core (bridge). Most notably is the addition of support
for local link multicast addresses in SR-IOV mode to the networking
core.
Also note, the ixgbe patch "ixgbe: Add support for pipeline reset" and
"ixgbe: Fix return value from macvlan filter function" is revised based
on community feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following build failure on S390:
In file included from drivers/net/ethernet/cadence/at91_ether.c:35:0:
drivers/net/ethernet/cadence/macb.h: In function 'macb_is_gem':
drivers/net/ethernet/cadence/macb.h:563:2: error: implicit declaration of function '__raw_readl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cadence/at91_ether.c: In function 'update_mac_address':
drivers/net/ethernet/cadence/at91_ether.c:119:2: error: implicit declaration of function '__raw_writel' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware doesn't support controlling pause frames autoneg, so
report that back correctly to userspace.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the module_pci_driver macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the module_pci_driver macro to make the code simpler
by eliminating the module_init and module_exit calls
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable retval is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the net device ops to manage the embedded
hardware bridge on ixgbe devices. With this patch the bridge
mode can be toggled between VEB and VEPA to support stacking
macvlan devices or using the embedded switch without any SW
component in 802.1Qbg/br environments.
Additionally, this adds source address pruning to the ixgbevf
driver to prune any frames sent back from a reflective relay on
the switch. This is required because the existing hardware does
not support this. Without it frames get pushed into the stack
with its own src mac which is invalid per 802.1Qbg VEPA
definition.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes a sparse warning triggered by us casting the timestamp in
the packet as a u64 instead of as a __le64. This change corrects that in
order to resolve the sparse warning.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are multiple places in our device nvm where the version is stored.
This update fixes some output errors with some types of images and
refactors the way the version data is gathered and stored for ethtool output.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Newer devices supported by igb can support auto-crossover detection in
forced operation modes. Enable this in the driver, rather than clobbering
this functionality in forced operation.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ignoring the return value from a call to the kernel dma_map API functions
can cause data corruption and system instability. Check the return value
and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver should not forward LLDP type frames. Inspect the ether type and
do not send if it is an LLDP ethertype frame.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hw timestamping code caused performance regression in ixgbe driver when the
timestamping is not enabled. The culprit is IXGBE_READ_REG call in the Rx
path which is executed for every received skb. This call is not needed when
the timestamping is disabled or for non-ptp packets.
netperf results:
The ixgbe side of the connection was acting as a server, the netperf command
line on the other side was:
netperf -H 192.168.1.23 -T0,0 -t UDP_STREAM -l 20
The values below mean throughput as reported by netperf (local/remote), for
3 runs, with timestamping not enabled.
3.7.0-rc1+ with CONFIG_IXGBE_PTP off:
5373.83 / 3329.32
5721.88 / 3033.89
5653.42 / 3112.38
3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5233.64 / 1226.85
5448.67 / 1039.32
5421.36 / 1095.66
Patched 3.7.0-rc1+ with CONFIG_IXGBE_PTP on:
5594.72 / 2942.53
5428.95 / 3110.16
5343.56 / 3200.48
Reported-by: Jesper Brouer <jbrouer@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Andy Gospodarek <gospo@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adds/updates ASCII descriptor maps for 82598 and 82599 Tx/Rx descriptors.
Current descriptor maps were out of date for 82598 and incorrect for
82599.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that compare the total_rx_packets cleaned to budget
instead of decrementing budget. The advantage to this approach is that budget
can now be const and we only end up modifying total_rx_packets instead of
modifying both it and budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When setting a MAC filter for the VF the function should return a success
or failure code, not the index of the new filter. It causes spurious NACK
returns to the VF driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies the check for calling en/disable_tx_laser() function
pointer. The pointer is only set on parts that can use it.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In SR-IOV mode the PF driver acts as the uplink port and is
used to send control packets e.g. lldpad, stp, etc.
eth0.1 eth0.2 eth0
VF VF PF
| | | <-- stand-in for uplink
| | |
--------------------------
| Embedded Switch |
--------------------------
|
MAC <-- uplink
But the embedded switch is setup to forward multicast addresses
to all interfaces both VFs and PF and onto the physical link.
This results in reserved MAC addresses used by control protocols
to be forwarded over the switch onto the VF.
In the LLDP case the PF sends an LLDPDU and it is currently
being forwarded to all the VFs who then see the PF as a peer.
This is incorrect.
This patch adds the multicast addresses to the RAR table in the
hardware to prevent this behavior.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function to set the macvlan filter should return success or failure
instead of the index of the filter. The message processing function was
misinterpreting the index as a non-zero return code indicating failure and
NACKing MAC filter set messages that actually succeeded.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Calling the ixgbe_reset_pipeline_82599 function will ensure a full pipeline
reset on all 82599 devices. This is necessary to avoid possible link issues.
Since this patch accomplishes this by modifying AUTOC.LMS we need to wrap
all AUTOC writes when LESM is enabled.
v2- fix LMS behaviour based on feedback by Martin Josefsson
CC: Martin Josefsson <gandalf@mjufs.se>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABCAAGBQJQiupBAAoJEENa44ZhAt0hPZkP/38m8O1eXFZoWA3wq4y3Wq/m
ZfKV4XD3PRFUUdcXGIdLbO0yE8+YvLIp0arxLS8C6lyKBe/EBHwByiq0uWccB7WY
I215Xo8hsaudAcylXWd1SvSFqbn/CjcMTpD3zATsvugxVf0iSOCX0bLUTXGLT56a
GfAUpJZ05fzM33atKLC5uMgCKBl4h1miAohA9ztPJusFupkuOHCCdWkqGFKCAZqm
85CUrlbz7nfl9mPbPlDYWT/ECzSSARKRAS0ZNkbYSGpZPx6G89L1NssYRpr8x1OC
tLr12kwIe3Aph5j1wZM7eQKgGV2B+9wFT8fGTLXRkHypMOvhXYJReNF91KX2mTUW
TcZ6WZHf7fCKx6rFNz1saS2yu2tiRwUTEr7NNmv5CLohMy/wRQTw6XHGVKZHvOVa
Tu8pBCcSZHI+zLpRdCosyMWHuxn2bx7psSNO8vC2earq4zSx4iOU3pdsKo2g2P25
Ut4Drm1LfzkglkeyuMv01azAyxSS0fEt1jjDacGdJmnPcz5dC0TpztlegLLZLHeq
BdM9sOham7dxHfuB5xY7AiAUt1i0VAejCn5QHnNIKwINqhJf9Zfj+RO/YmAi80ox
XOveVQT6L/60LFi0ntEAUakiwq6vPMJRFjWfw883fwhXcmuaxChHJhQU2iN0CDD1
XZI37iVsDm9eFYDl2VSj
=1EJ/
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Small batch of fixes for 3.7:
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Perform correct resource cleanup if mlx4_QUERY_ADAPTER() fails
mlx4_core: Remove annoying debug messages from SR-IOV flow
RDMA/cxgb4: Don't free chunk that we have failed to allocate
IB/mlx4: Synchronize cleanup of MCGs in MCG paravirtualization
IB/mlx4: Fix QP1 P_Key processing in the Primary Physical Function (PPF)
IB/mlx4: Fix build error on platforms where UL is not 64 bits
This change correctly computes the header length and data length in
the fragments to avoid a bug where we would end up with extremely
slow performance. Also adopt use of skb_frag_size() accessor.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org [v3.6]
Signed-off-by: David S. Miller <davem@davemloft.net>
If a failure takes place during the EQ creation, we need to unmap the
UAR memory block too.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Uri Habusha <urih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan tag can be zero. This is why it can't serve as an indication
that packet requires VLAN header in the TX flow.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).
Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable ALDPS function to save power when link down. Note that the
feature should be set after the other PHY settings. And the firmware
is necessary. Don't enable it without loading the firmware.
None of the firmware-free chipsets support ALDPS. Neither do the
RTL8168d/8111d.
For 8136 series, make sure the ALDPS is disabled before loading the
firmware. For 8168 series, the ALDPS would be disabled automatically
when loading firmware. You must not disable it directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a 36 bit dtb file, the driver complains "resource busy".
Investigating the source of the message leads one to the
gianfar_ptp_probe function.
Since the type of the device resource requested in this function
is IORESOURCE_MEM, it should use "iomem_resource" instead of
"ioports_resource".
Signed-off-by: Wei Yang <Wei.Yang@windriver.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw/davinci mdio ip cores are present on am33xx, so make NET_VENDOR_TI
visible for it as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to allocate rx buffers pool by any reason, we'll just return
with an error, however we've previously successfully requested an irq. Fix
this by releasing the irq before returning the error.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW flashing code, even though it works correctly, makes some hidden
assumptions about buffer sizes. This is causing code analysers to
report error. Cleanup FW flashing code to remove these hidden assumptions.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed the resource cleanup to act correctly and prevent a kernel oops when
mlx4_QUERY_ADAPTER() fails.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These debug prints left behind by commits c82e9aa0a8 ("mlx4_core:
resource tracking for HCA resources used by guests"), 54679e1482
("mlx4: Implement QP paravirtualization and maintain phys_pkey_cache
for smp_snoop") and 993c401e20 ("mlx4_core: Add IB port-state
machine and port mgmt event propagation") make it pretty hard to
actually use the mlx4_core debug messages when running in SRIOV/IB
mode -- for example, the module load sequence of a device with one VF
yielded 631 debug prints, with 408 of them being from this set. Let's
just remove them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Ignoring the return value from a call to the kernel dma_map API functions
can cause data corruption and system instability. Check the return value
and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the igb driver version to 4.0.17.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a problem in the initial implementation of the get cable length
function for i210 and it did not work properly. This patch fixes that
problem for i210/i211 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a HW requirement. Although a buffer as short as 1 byte is allowed,
the total length of packet before, padding and CRC insertion, must be at
least 17 bytes. So pad all small packets manually up to 17 bytes before
delivering them to HW.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe only. Only change to this series
is I dropped the "ixgbe: Add support for pipeline reset" due to
change requested by Martin Josefsson.
Alexander Duyck (7):
ixgbe: Add support for IPv6 and UDP to ixgbe_get_headlen
ixgbe: Add support for tracking the default user priority to SR-IOV
ixgbe: Add support for GET_QUEUES message to get DCB configuration
ixgbe: Enable support for VF API version 1.1 in the PF.
ixgbevf: Add VF DCB + SR-IOV support
ixgbe: Drop unnecessary addition from ixgbe_set_rx_buffer_len
ixgbe: Fix possible memory leak in ixgbe_set_ringparam
Don Skidmore (1):
ixgbe: Add function ixgbe_reset_pipeline_82599
Emil Tantilov (1):
ixgbe: add WOL support for new subdevice id
Jacob Keller (1):
ixgbe: (PTP) refactor init, cyclecounter and reset
Tushar Dave (1):
ixgbe: Correcting small packet padding
Wei Yongjun (1):
ixgbe: using is_zero_ether_addr() to simplify the code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow us to remove the last mach include from at91_ether
and also make it easier to share address setup with macb.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that HAVE_NET_MACB is gone let's just select MACB to
satisfy the dependecies in at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb is a platform driver and there is nothing that prevents
this driver from being built on non-ARM/AVR32 platforms.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building macb on x86_64 the following warnings show up:
drivers/net/ethernet/cadence/macb.c: In function macb_interrupt:
drivers/net/ethernet/cadence/macb.c:556:4: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c: In function macb_reset_hw:
drivers/net/ethernet/cadence/macb.c:792:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c:793:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
drivers/net/ethernet/cadence/macb.c:796:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Use -1 insted of ~0UL, as done in other places in the driver,
to silence these warnings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when FIFO_ERR happens, we stop the dma, wait for it to become
idle and then reset the whole MAC_RX logic (and after that we must re-set
multicast addresses and also re-enable MAC_RX when we're finally ready to
accept new packets). This leads to CRC errors on high number of incoming
packets and is not needed according to the datasheet.
This patch fixes it by the following steps:
1) remove this reset in pch_gbe_stop_receive(), which causes some functions
to not be used anywhere
2) remove already unused functions pch_gbe_wait_clr_bit_irq() and
pch_gbe_mac_reset_rx() to correctly build
3) move pch_gbe_enable_mac_rx() out of pch_gbe_start_receive() to
pch_gbe_up() where it's only needed after we've removed the MAC_RX reset
4) rename pch_gbe_start/stop_receive() to pch_gbe_enable/disable_dma_rx()
to more precisely reflect what the functions are now doing.
After these changes we already don't see the CRC errors and gain some
increase in RX processing speed.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we were in RX_FIFO_ERR state and entered pch_gbe_napi_poll(), we'll
anyway clean some rx space and thus can continue to receive more packets.
Currently, we re-set the RX_FIFO_ERR in situations when we've exhausted our
budget for RX cleaning or cleaned some TX packets. Removing it gives us
+20%-40% speed increase and a lot less of RX_FIFO_ERRors reported.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move MAC_RX-related bits into separate functions.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were not correctly freeing the temporary rings on error in
ixgbe_set_ring_param. In order to correct this I am unwinding a number of
changes that were made in order to get things back to the original working
form with modification for the current ring layouts.
This approach has multiple advantages including a smaller memory footprint,
and the fact that the interface is stopped while we are allocating the rings
meaning that there is less potential for some sort of memory corruption on the
ring.
The only disadvantage I see with this approach is that on a Rx allocation
failure we will report an error and only update the Tx rings. However the
adapter should be fully functional in this state and the likelihood of such
an error is very low. In addition it is not unreasonable to expect the
user to need to recheck the ring configuration should they experience an
error setting the ring sizes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a function that forces a full pipeline reset. This
function will be used in following patches to completely reset the PHY
during resets.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We still had some code floating around from the old single buffer receive
path. As a result we were adding VLAN_HLEN to max_frame although the
resultant value was never used. Since that is the case we can drop this from
the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver pad skb up to 17 bytes because of the HW requirement. However, that code
implementation mess up the skb tail pointer after padding. This patch sets
skb->tail correctly.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using is_zero_ether_addr() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies when and where PTP registers and data are set. Previously
a work-around was used inside cyclecounter_start in order to reset some of the
time registers. This patch creates a new ixgbe_ptp_reset specifically for this
purpose. The cyclecounter configuration has trimmed down to only modify what
is necessary. Due to hardware conditions after probe and before open, PTP init
has now moved into the ixgbe_open call. This allows the ptp device name in the
sysfs to be the ethernet device name instead of the MAC address.
The cyclecounter check flag is renamed to PTP_ENABLED and is used to prevent
PTP init from happening when PTP has not been enabled.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a subdevice id for new 82599 device. The define is needed
to allow enabling WOL support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for DCB and SR-IOV from the VF. With this change
in place the VF will correctly use a traffic class other than 0 in the case
that the PF is configured with the default user priority belonging to a
traffic class other than 0.
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change switches on the last few bits for us enabling version 1.1 VF
support in the PF.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch addresses several issues in regards to the combination of DCB
and SR-IOV. Specifically it allows us to send information to the VF on
which queues it should be using.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is necessary to track the default user priority in the PF so that we can
force it upon the VFs. The motivation behind this is to keep the VFs from
getting access to user priorities meant for things like storage.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for IPv6 and UDP to ixgbe_get_headlen. The
advantage to this is that we can now handle ipv4/UDP, ipv6/TCP, and
ipv6/UDP with a single memcpy instead of having to do them in multiple
pskb_may_pull calls.
A quick bit of testing shows that we increase throughput for a single
session of netperf from 8800Mpbs to about 9300Mpbs in the case of ipv6/TCP.
As such overall ipv6 performance should improve with this change.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Before use the request and response queue addr, make sure it has wrote
to the registers.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW flash layout on Skyhawk-R is different from BE3-R.
Hence the code needs to be fixed to flash FW on Skyhawk-R.
Also cleaning up code in BE3-R flashing function.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_shutdown is enabling wake-on-lan by calling be_setup_wol.
Emulex adapter do not support wake-on-lan in S5 state.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver should enable VF so that VF goes to ready state in
new Lancer FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCI EEH, driver waits for all functions in the card.
Wait is needed only once per card. Fix is to wait only for the
first PCI function.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During recovery from a FW error, destroy queue operation may fail.
Queue should be marked as destroyed so that recovery code can recreate
the queue. Also fix queue created state not getting checked at one instance.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return default values for fields for which VFs dont have privilege to get the
required information from FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF does not have privileges to execute many commands. When VFs try
to execute those commands there are unnecessary error messages.
Fix this by executing only those commands for which VF has privilege.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow adding VLANs for Lancer VF.
VLAN ID 0 should not be added to list of VLANs sent to FW.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After FW error, driver should wait for NO_RESOURCE error to disappear before
proceeding with recovery.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For changing MAC of VF from PF, delete MAC operation needs to be done before
assigning new MAC. Also in ndo_set_mac_address operation avoid delete MAC if
it has been already deleted by PF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use Lancer specific command to set QoS for VF.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver assumes FW resource counts and capabilities while creating queues and
using functionality like RSS. This causes driver load to fail in FW configs
where resources and capabilities are reduced. Fix this by querying FW
configuration during probe and using resources and capabilities accordingly.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also fixes the build failure caused due to removal of #ifdef
CONFIG_CHELSIO_T4_OFFLOAD condition
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to ixgbe and igb.
Alexander Duyck (13):
ixgbe: Initialize q_vector cpu and affinity masks correctly
ixgbe: Enable jumbo frames support w/ SR-IOV
ixgbe: Move message handling routines into their own functions
ixgbe: Add mailbox API version negotiation support to ixgbe PF
igb: Split Rx timestamping into two separate functions
igb: Do not use header split, instead receive all frames into a
single buffer
igb: Combine post-processing of skb into a single function
igb: Map entire page and sync half instead of mapping and unmapping
half pages
igb: Move rx_buffer related code in Rx cleanup path into separate
function
igb: Lock buffer size at 2K even on systems with larger pages
igb: Combine q_vector and ring allocation into a single function
igb: Move the calls to set the Tx and Rx queues into igb_open
igb: Split igb_update_dca into separate Tx and Rx functions
Tushar Dave (1):
igb: Correcting and improving small packet check and padding
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does two things:
* Use macb struct members and remove at91_ether ones
* Alloc DMA buffers on netdev start and dealloc on stop
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This rips out the at91_ether phy handling and ethtool stuff
and replace it with equivalent stuff from macb.
The only thing lost is the phy irq support from at91_ether,
but this can be added to macb and then benefit all users.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This will make it easier to share code between the drivers and
eventually merge them into one driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Use register and bits definitions from the macb header. This makes it
possible to have one header file for this hardware.
Process was scripted and the resulting object file has the same checksum.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
This change makes it so that igb_update_dca is broken into two halves, one
for Rx and one for Tx. The advantage to this is primarily readability.
In addition I am enabling relaxed ordering for reads from hardware since
this is supported on all of the igb parts.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change helps to address locking issues seen with
netif_set_real_num_tx_queues and netif_set_real_num_rx_queues when used in
the igb_set_interrupt_capability function. To resolve these locking issues
I have moved the two function calls into __igb_open so that they can be
called while the RTNL lock is held.
An added advantage to this is that the number of queues is not updated
until the last possible moment so if there are any issues in allocating
MSI-X interrupts or resources for the rings we have time to change the
values prior to updating the netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change combines the the allocation of q_vectors and rings into a single
function. The advantage of this is that we are guaranteed we will avoid
overlap in the L1 cache sets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change locks us in at 2K buffers even on a system that supports larger
frames. The reason for this change is to make better use of pages and to
reduce the overall truesize of frames generated by igb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to try and isolate things a bit further I am moving the code
related to retrieving data from the rx_buffer_info structure into a
separate function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we map the entire page and just sync half of
it for the device at a time. The advantage to this approach is that we can
avoid the locking on map/unmap seen in many IOMMU implementations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to just clean-up a number of function calls that were
made at the end of the Rx clean-up path by combining them into a single
function call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we no longer use header split. The idea is to
reduce partial cache line writes by hardware when handling frames larger
then header size. We can compensate for the extra overhead of having to
memcpy the header buffer by avoiding the cache misses seen by leaving an
full skb allocated and sitting on the ring.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support page based receive we will need to split up the two
different types of timestamping into two separate functions. The first one
will handle legacy timestamps with the value in the register, and the new
one will handle timestamps in the Rx buffer itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current implementation mess up the tail pointer. This patch sets skb->tail
correctly.
Also, the small packet check and padding is optimized by using unlikely and
calling skb_pad directly.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change allows us to add a mailbox versioning API. This will allow us
to determine the features supported by the VFs from the PF. For example we
will be implementing a version 1.1 API for the VF that will indicate that
it can support us enabling Jumbo frames as the VF will support buffer
chaining.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Robert Garrett <RobertX.Garrett@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of trying to maintain one large monolithic function that handles
most of the different messages from the VF it makes sense to break the
message handling function up so that we can just go through one switch
statement and call the correct routine for a given message.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can have limited support for jumbo frames
when SR-IOV is enabled. In order to accomplish this it is necessary to
disable all VFs when the PF has jumbo frames enabled. If the VFs then
request the same maximum frame size as the PF they will be re-enabled. A
follow on patch will add a means of identifying when a VF can support
spanning buffers and does not need to be worried about the actual supported
max frame size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Robert Garrett <robertx.e.garrett@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling DCB the rings belonging to a q_vector on CPU 0 were not
reinitializing their DCA registers. Upon closer inspection the issue was
that the q_vector CPU variable was left at 0 resulting in the driver not
updating the DCA registers.
In order to guarantee the DCA registers will be updated I am adding a
couple line change so that we initialize the CPU variable to -1 which will
force a DCA update the first time an interrupt fires on that q_vector.
In addition we were setting the CPU affinity hint to all CPUs when we were
not specifying a CPU. Instead we should leave it as all zeros to avoid any
possible confusion about the fact that we shouldn't be giving a hint.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit a3348722 AFEX FCoE function is continuously reset.
The patch prevents the resetting and removes debug print
to stop garbaging syslog.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patch from Matthew Garrett <mjg@redhat.com> (https://lkml.org/lkml/2011/11/11/168).
http://driveragent.com/archive/30421/7-0-14 indicates that ASPM is
disabled on the 250 and 260. Duplicate for sanity.
Fixes random RX engine hangs I experienced with JMC250 on Clevo W270HU.
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Cc: Guo-Fu Tseng <cooldavid@cooldavid.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch originated from Hiroaki SHIMODA but has been modified
by Intel with some minor cleanups and additional commit log text.
Denys Fedoryshchenko and others reported Tx stalls on e1000e with
BQL enabled. Issue was root caused to hardware delays. They were
introduced because some of the e1000e hardware with transmit
writeback bursting enabled, waits until the driver does an
explict flush OR there are WTHRESH descriptors to write back.
Sometimes the delays in question were on the order of seconds,
causing visible lag for ssh sessions and unacceptable tx
completion latency, especially for BQL enabled kernels.
To avoid possible Tx stalls, change WTHRESH back to 1.
The current plan is to investigate a method for re-enabling
WTHRESH while not harming BQL, but those patches will be later
for net-next if they work.
please enqueue for stable since v3.3 as this bug was introduced in
commit 3f0cfa3bc1
Author: Tom Herbert <therbert@google.com>
Date: Mon Nov 28 16:33:16 2011 +0000
e1000e: Support for byte queue limits
Changes to e1000e to use byte queue limits.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
CC: eric.dumazet@gmail.com
CC: therbert@google.com
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain platforms, BE hardware could falsely indicate UE.
For BE family of NICs, do not set hw_error based on the UE bits.
If there was a real fatal error, the corresponding h/w block will
automatically go offline and stop traffic.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fengguang reported a kernel build failure as following:
drivers/built-in.o: In function `pch_gbe_ioctl':
pch_gbe_main.c:(.text+0x510370): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x510393): undefined reference to `pch_ch_control_write'
pch_gbe_main.c:(.text+0x5103b3): undefined reference to `pch_ch_control_write'
...
It's a regression by commit da1586461. The root cause is that
the CONFIG_PPS is not set there, consequently CONFIG_PTP_1588_CLOCK
can not be set anyway, which finally causes ptp_pch and pch_gbe_main
build failures.
As David prefers to use *select* to fix such module co-dependency issues,
this patch explicitly selects all the possible dependencies of PCH_PTP.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Haicheng Li <haicheng.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pulled mainline in order to get the UAPI infrastructure already
merged before I pull in David Howells's UAPI trees for networking.
Signed-off-by: David S. Miller <davem@davemloft.net>
i218 is the next-generation LOM that will be available on systems with the
Lynx Point LP Platform Controller Hub (PCH) chipset from Intel. This patch
provides the initial support of those devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change limits the PF/VF driver to 9.5K max jumbo frame size in order
prevent a possible Tx hang in the adapter when sending frames between
pools.
All of the parts in ixgbe support a maximum frame of 15.5K for standard
traffic, however with SR-IOV or DCB enabled they should be limiting the
MTU size to 9.5K. Instead of adding extra checks which would have to
change the MTU when we go into or out of these modes it is preferred to
just use a standard 9.5K MTU limit for all modes so that this extra
overhead can be avoided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not setting the number of real Tx queues in the net_device
structure. This caused some serious issues such as Tx hangs and extremely
poor performance with some usages of the driver.
The issue is best observed by running:
iperf -c <host> -P <n>
Where n is greater than one. The greater the value of n the more likely
the problem is to show up.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>