ASoC: Updates for v5.11
There's a lot of changes here but mostly cleanups and driver specific
things, the most user visible change is the support for boot time
selection of Intel DSP firmware which will make it easier for people to
move over to the preferred modern implementations in distros and other
large scale deployments.
This also includes a merge of the new auxillary bus which was done in
anticipation of use by the Intel DSP drivers which didn't quite make it.
- Lots more cleanups and simplifications from Morimoto-san.
- Support for some basic DPCM systems in the audio graph card from
Sameer Pujar.
- Remove some old pre-DT Freescale drivers for platforms that are now
DT only.
- Move selection of which Intel DSP implementation to use to boot time
rather than requiring it to be selected at build time.
- Support for Allwinner H6 I2S, Analog Devices ADAU1372, Intel
Alderlake-S, GMediatek MT8192, NXP i.MX HDMI and XCVR, Realtek RT715,
Qualcomm SM8250 and simple GPIO based muxes.
The TI/OMAP sound drivers use Common Clock Framework thus they cannot be
built on platforms without it (e.g. compile test on MIPS with RALINK and
SOC_RT305X):
/usr/bin/mips-linux-gnu-ld: sound/soc/ti/davinci-mcasp.o:davinci-mcasp.c:(.text+0x1c64): more undefined references to `clk_set_parent' follow
/usr/bin/mips-linux-gnu-ld: sound/soc/ti/omap-dmic.o: in function `omap_dmic_set_dai_sysclk':
omap-dmic.c:(.text+0xa5c): undefined reference to `clk_get_parent'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201116175133.402553-4-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
McASP needs three required properties to be usable for audio:
op-mode, tdm-slots and the serial-dir array.
Instead of probing the driver even without the needed information we should
make sure that all the parameters are provided for operation.
The fact that McASP can act as a GPIO controller for it's pins complicates
this a bit, but as a general rule we can:
- we fail the probe if McASP is not configured to be used as gpiochip
- we will not register the DAI (and PCM) if gpiochip is defined
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201106072551.689-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the davinci_mcasp_set_pdata_from_of() function which returned a
pdata pointer with davinci_mcasp_get_config() to return an actual error
code and handle all pdata validation and private mcasp struct setup in
there.
Drop the unused ram-size-playback and sram-size-capture query from DT at
the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201106072551.689-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the integration of McASP either the 'common' or the
'rx' and 'tx' or only the 'tx' interrupt number is valid, provided.
By switching to platform_get_irq_byname_optional() we can clean up the
bootlog from messages like:
davinci-mcasp 2ba0000.mcasp: IRQ common not found
The irq number == 0 is not valid, fix the check at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201106072551.689-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 9c34d023dc ("ASoC: omap-mcbsp: Re-arrange files for core McBSP
and Sidetone function split"), in rearranging various files, also replaced
calls to platform_get_resource_by_name() + devm_ioremap_resource() with a
single call to devm_platform_ioremap_resource_byname(). However, the
struct resource is needed as we access its members so at present a null
pointer is dereferenced. Fix by doing things the old way.
Fixes: 9c34d023dc ("ASoC: omap-mcbsp: Re-arrange files for core McBSP and Sidetone function split")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20201004102535.325547-1-alex.dewar90@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_J721E_EVM should not select SND_SOC_PCM3168A_I2C when I2C
is not enabled. That causes build errors, so make this driver's
symbol depend on I2C.
WARNING: unmet direct dependencies detected for SND_SOC_PCM3168A_I2C
Depends on [n]: SOUND [=m] && !UML && SND [=m] && SND_SOC [=m] && I2C [=n]
Selected by [m]:
- SND_SOC_J721E_EVM [=m] && SOUND [=m] && !UML && SND [=m] && SND_SOC [=m] && (DMA_OMAP [=y] || TI_EDMA [=m] || TI_K3_UDMA [=n] || COMPILE_TEST [=y]) && (ARCH_K3_J721E_SOC [=n] || COMPILE_TEST [=y])
../sound/soc/codecs/pcm3168a-i2c.c:59:1: warning: data definition has no type or storage class
module_i2c_driver(pcm3168a_i2c_driver);
^~~~~~~~~~~~~~~~~
../sound/soc/codecs/pcm3168a-i2c.c:59:1: error: type defaults to ‘int’ in declaration of ‘module_i2c_driver’ [-Werror=implicit-int]
../sound/soc/codecs/pcm3168a-i2c.c:59:1: warning: parameter names (without types) in function declaration
../sound/soc/codecs/pcm3168a-i2c.c:49:26: warning: ‘pcm3168a_i2c_driver’ defined but not used [-Wunused-variable]
static struct i2c_driver pcm3168a_i2c_driver = {
^~~~~~~~~~~~~~~~~~~
cc1: some warnings being treated as errors
Fixes: 6748d05590 ("ASoC: ti: Add custom machine driver for j721e EVM (CPB and IVI)")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/e74c690c-c7f8-fd42-e461-4f33571df4ef@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200718112403.13709-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200718110857.11520-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dai_digital_mute() is internally using both
mute_stream() (1) or digital_mute() (2), but the difference between
these 2 are only handling direction.
We can merge digital_mute() into mute_stream
int snd_soc_dai_digital_mute(xxx, int direction)
{
...
else if (dai->driver->ops->mute_stream)
(1) return dai->driver->ops->mute_stream(xxx, direction);
else if (direction == SNDRV_PCM_STREAM_PLAYBACK &&
dai->driver->ops->digital_mute)
(2) return dai->driver->ops->digital_mute(xxx);
...
}
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/87blkpxxip.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio support on the board is using pcm3168a codec connected to McASP10
serializers in parallel setup.
The pcm3168a SCKI clock is coming via the j721e AUDIO_REFCLK2 pin.
In order to support 48KHz and 44.1KHz family of sampling rates the parent clock
for AUDIO_REFCLK2 needs to be changed between PLL4 (for 48KHz) and PLL15 (for
44.1KHz). The same PLLs are used for McASP10's AUXCLK clock via different
HSDIVIDER.
Generic card can not be used for the board as we need to switch between
clock paths for different sampling rate families and also need to change
the slot_width between 16 and 24 bit audio.
The audio support on the Infotainment Expansion Board consists of McASP0
connected to two pcm3168a codecs with dedicated set of serializers to each.
The SCKI for pcm3168a is sourced from j721e AUDIO_REFCLK0 pin.
It is extending the audio support on the CPB.
Due to the fact that the same PLL4/15 is used by both domains (CPB/IVI)
there are cross restriction on sampling rates.
The IVI side is represented as multicodec setup.
PCMs available on a plain CPB (no IVI addon):
hw:0,0 - cpb playback (8 channels)
hw:0,1 - cpb capture (6 channels)
When the IVI addon is present, additional two PCMs will be present:
hw:0,2 - ivi multicodec playback (16 channels)
hw:0,3 - ivi multicodec capture (12 channels)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200630125843.11561-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If an error occurs after the call to 'omap_mcbsp_init()', the reference to
'mcbsp->fclk' must be decremented, as already done in the remove function.
This can be achieved easily by using the devm_ variant of 'clk_get()'
when the reference is taken in 'omap_mcbsp_init()'
This fixes the leak in the probe and has the side effect to simplify both
the error handling path of 'omap_mcbsp_init()' and the remove function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Link: https://lore.kernel.org/r/20200512134325.252073-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
davinci_mcasp_get_dma_type() invokes dma_request_chan(), which returns a
reference of the specified dma_chan object to "chan" with increased
refcnt.
When davinci_mcasp_get_dma_type() returns, local variable "chan" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one exception handling path of
davinci_mcasp_get_dma_type(). When chan device is NULL, the function
forgets to decrease the refcnt increased by dma_request_chan(), causing
a refcnt leak.
Fix this issue by calling dma_release_channel() when chan device is
NULL.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/1587818916-38730-1-git-send-email-xiyuyang19@fudan.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull sound updates from Takashi Iwai:
"This became again a busy development cycle. There are few ALSA core
updates (merely API cleanups and sparse fixes), with the majority of
other changes are found in ASoC scene.
Here are some highlights:
ALSA core:
- More helper macros for sparse warning fixes (e.g. bitwise types)
- Slight optimization of PCM OSS locks
- Make common handling for PCM / compress buffers (for SOF)
ASoC:
- Lots of code refactoring and modernization for (still ongoing)
componentization works
- Conversion of SND_SOC_ALL_CODECS to use imply
- Continued refactoring and fixing of the Intel SOF/SST support,
including the initial (but still incomplete) SoundWire support
- SoundWire and more advanced clocking support for Realtek RT5682
- Support for amlogic GX, Meson 8, Meson 8B and T9015 DAC, Broadcom
DSL/PON, Ingenic JZ4760 and JZ4770, Realtek RL6231, and TI TAS2563
and TLV320ADCX140
HD-audio:
- Optimizations in HDMI jack handling
- A few new quirks and fixups for Realtek codecs
USB-audio:
- Delayed registration support
- New quirks for Motu, Kingston, Presonus"
* tag 'sound-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: usb-audio: Fix case when USB MIDI interface has more than one extra endpoint descriptor
Revert "ALSA: uapi: Drop asound.h inclusion from asoc.h"
ALSA: hda/realtek - Remove now-unnecessary XPS 13 headphone noise fixups
ALSA: hda/realtek - Set principled PC Beep configuration for ALC256
ALSA: doc: Document PC Beep Hidden Register on Realtek ALC256
ALSA: hda/realtek - a fake key event is triggered by running shutup
ALSA: hda: default enable CA0132 DSP support
ASoC: amd: acp3x-pcm-dma: clean up two indentation issues
ASoC: tlv320adcx140: Remove undocumented property
ASoC: Intel: sof_sdw: Add Volteer support with RT5682 SNDW helper function
ASoC: Intel: common: add match table for TGL RT5682 SoundWire driver
ASoC: Intel: boards: add sof_sdw machine driver
ASoC: Intel: soc-acpi: update topology and driver name for SoundWire platforms
ASoC: rt5682: move DAI clock registry to I2S mode
ASoC: pxa: magician: convert to use i2c_new_client_device()
ASoC: SOF: Intel: hda-ctrl: add reset cycle before parsing capabilities
Asoc: SOF: Intel: hda: check SoundWire wakeen interrupt in irq thread
ASoC: SOF: Intel: hda: add WAKEEN interrupt support for SoundWire
ASoC: SOF: Intel: hda: add parameter to control SoundWire clock stop quirks
ASoC: SOF: Intel: hda: merge IPC, stream and SoundWire interrupt handlers
...
Call cpu_latency_qos_add/update/remove_request() and
cpu_latency_qos_request_active() instead of
pm_qos_add/update/remove_request() and pm_qos_request_active(),
respectively, because the latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
There is no big difference at implementation for .suspend/.resume
between DAI driver and Component driver.
But because some driver is using DAI version, thus ALSA SoC needs
to keep supporting it, hence, framework becoming verbose.
If we can switch all DAI driver .suspend/.resume to Component driver,
we can remove verbose code from ALSA SoC.
Driver is getting its private data via dai->dev.
But dai->dev and component->dev are same dev, thus, we can convert
these. For same reason, we can convert dai->active to
component->active if necessary.
This patch moves DAI driver .suspend/.resume to Component driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/871rrvym3p.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When McASP is master the bclk can be generated from two main source:
AUXCLK: functional clock for McASP or
AHCLK: from external source or internal mux in dra7x family
With this patch it is possible to select between the two source. The patch
is not breaking existing machine drivers since historically the clk_id was
ignored and left as 0 in all cases.
When output clock is configured - which can be only the AHCLK, we select
the AUXCLK as source for the internal HCLK. In this case the HCLK rate is
the same as the output clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191204192005.31210-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
